Preparation and the optical nonlinearity of surface chemistry improved titania nanoparticles in poly(methyl methacrylate)-titania hybrid thin films

With 800-nm, 120-fs laser pulses, optical nonlinearity has been studied in a series of thin films containing poly(methyl methacrylate) (PMMA), filled with surfactant acetylacetone (Acac) capped TiO₂ nanoparticles, which were synthesized by a simple in situ sol-gel/polymerization process, assisted by spin coating and multi-step baking. The resulting nanohybrid thin films have highly optical transparency and demonstrate a unique nonlinear optical (NLO) response. The highest nonlinear refractive index (n₂) is observed up to 6.55 × 10⁻² cm² GW⁻¹ in the nanohybrid thin film of 60 wt% Ti(OBu)₄ in PMMA, with a negligible two-photon absorption (TPA), as confirmed by the Z-scan technique. The titanium precursor loading combined with the nature of the capping molecules are used to influence the ability of nanoparticles to nonlinear optical response. Indeed, the ligands at the nanoparticles’ surface can not only control the extent of the interaction between the organic molecules and the embedded nanoparticles but also influence the optical nonlinearities of nanoparticles.     

Optical properties of poly(methyl methacrylate)–titania nanostructure thin films containing ellipsoid-shaped titania nanoparticles from ex-situ sol-gel method at low growth temperature

This paper reports on the linear and nonlinear optical responses of the PMMA-TiO₂ nanohybrid thin films which are synthesized by a flexible ex-situ sol-gel/polymerization process, assisted by spin coating and multi-step baking. Triethanolamine (TEOA) as surfactant and shape controller is used to modify the interface between PMMA and TiO₂, allowing a highly homogeneous dispersion of the ellipsoid-shaped TiO₂ nanoparticles. The resulting nanohybrid thin films have highly optical transparency as proved by the linear absorption photon-energy spectra and indicate an enhanced nonlinear optical (NLO) response as confirmed by the Z-scan technique using 800-nm, 120-femtosecond (fs) laser pulses, highlighting the potential of the nanocomposites for efficient optical devices.     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术,分别沉积Ti和Ti/Al膜,经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序,分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27 关键词： 2薄膜')" href="#">多孔TiO₂薄膜 阳极氧化 紫外光吸收     

Quantum confinement effects of CdTe nanocrystals sequestered in TiO2 matrix: effect of oxygen incorporation

Thin films of TiO₂ with high volume fraction (40–55%) and crystallite size (6–40 nm) of CdTe nanoparticles had been prepared by rf magnetron sputtering from a composite TiO₂:CdTe target at room temperature and 373 K. A detailed optical properties of nanocrystalline CdTe:TiO₂ films as-deposited and after thermal treatment (300 °C) are studied. The absorbance of the TiO₂ films with CdTe nanocrystallite dispersions depends both on the nanocrystallite size and volume fraction. The blue-shifts of the optical absorption edge concurrent with the CdTe nanocystal size reduction for as-deposited and after thermal treatment of nanocrystalline CdTe:TiO₂ thin films with respect to the bulk semiconductor agrees quite well with the strong quantum confinement theory. A slight deviation in absorption edge values than the predicted values from the strong quantum confinement model can be attributed to change in interplanar distance due to oxygen incorporation and inhomogeneous size distribution of CdTe nanocrystallites in these films.     

Mesoporous titania films investigated by positron annihilation based on a slow positron beam

Tunable mesoporous titania (TiO₂) thin films were synthesized via a sol-gel method using an amphiphilic triblock copolymer F38 as the structural template. The dependence of crystalization, pore morphology and interconnectivity of TiO₂ films on the weight ratio of F38 was studied by wide-angle X-ray diffraction, field emission scanning electron microscopy and Doppler broadening of positron annihilation radiation spectroscopy based on a slow positron beam. By loading more F38, the crystallization of TiO₂ films is enhanced, accompanied by a decrement in oxygen vacancies/grain boundaries. Smaller and isolated mesopores are formed in the films prepared with F38 less than 15?wt%. The pore percolation occurs when the weight ratio of F38 is up to 20?wt% and larger and interconnected worm-like pores are formed.     

Excimer laser processing as a tool for photocatalytic design of sol-gel TiO2 thin films

Nanostructured sol-gel TiO₂ thin films spin coated on silicate glass plates are subjected to excimer (KrF^*) pulsed laser irradiation in order to tailor their structure and photocatalytic properties. The surface morphology of virgin and laser-processed films are followed applying electron optical imaging and atomic force microscopy. The evolution of the surface roughness and pore formation are shown to be accompanied by optical absorption edge shift to infrared wavelength range. Conventional X-ray diffraction analysis and high-resolution transmission electron imaging are applied in order to obtain information on the phase composition. Co-existence of amorphous and anatase TiO₂ phases in nonirradiated sol-gel films is found. It is established that after laser processing the most intense XRD anatase peak is shifted to lower 2θ range. The analysis of high-resolution transmission electron images of film profiles evidences for the laser induced phase transitions. Formation of rutile and brookite TiO₂ accompanied by evolution of oxygen deficient Ti_nO_2n−1 phases are identified in the subsurface region. The contribution of laser processing for increasing the photocatalytic efficiency of laser-modified films toward the oxidation of methylene blue water solution is demonstrated. The results obtained reveal a novel-processing route for designing sol-gel titania films with improved photocatalytical activity.     

The effect of the deposition parameters on size, distribution and antimicrobial properties of photoinduced silver nanoparticles on titania coatings

Controlled photodeposition of silver nanoparticles (AgNP) on titania coatings using two different sources of UV light is described. Titania (anatase) thin films were prepared by the sol-gel dip-coating method on silicon wafers. AgNPs were grown on the titania surface as a result of UV illumination of titania films immersed in aqueous solutions of silver nitrate. UV xenon lamp or excimer laser, both operating at the wavelength 351 ± 5 nm, was used as illumination sources. The AFM topography of AgNP/TiO₂ nanocomposites revealed that silver nanoparticles could be synthesized by both sources of illumination, however the photocatalysis carried out by UV light from xenon lamp illumination leads to larger AgNP than those synthesized using the laser beam. It was found that the increasing concentration of silver ions in the initial solution increases the number of Ag nanoparticles on the titania surface, while longer time of irradiation results the growth of larger size nanoparticles. Antibacterial tests performed on TiO₂ covered by Ag nanoparticles revealed that increasing density of nanoparticles enhances the inhibition of bacterial growth. It was also found that antibacterial activity drops by only 10-15% after 6 cycles compared to the initial use.     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

银/二氧化钛核壳纳米颗粒对碲化镉纳米晶的荧光增强研究

利用新合成的复合纳米结构银/二氧化钛核壳纳米颗粒,研究了金属银纳米颗粒对碲化镉纳米晶层荧光的增强情况.结果表明,这种新型复合金属纳米结构能极大地增强发光纳米晶层的荧光强度.银/二氧化钛核壳纳米颗粒是以水合肼、硝酸银和四异丙氧基钛为原材料,利用胶体化学法在水溶液中合成.透射电子显微镜图片表明这种新合成的银/二氧化钛纳米材料基本上呈球形,有较为明显的核壳结构,中间黑色的核是银纳米颗粒,外层颜色较浅部分是二氧化钛壳层.另外,包裹二氧化钛壳层后,银纳米颗粒的表面等离子吸收带从409 nm红移至430 nm,也证实了这种新型核壳纳米材料的形成.将此合成方法得到的银/二氧化钛纳米颗粒和碲化镉纳米晶用旋转涂覆方法进行直接组合后,得到了银纳米颗粒对碲化镉纳米晶荧光的明显增强,并对其增强的物理过程进行了讨论.这种能够增强荧光团发光的新型复合银纳米结构将在发光器件、荧光成像、生物探测等方面具有一定的应用价值.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Transparent nano composite PVA–TiO2 and PMMA–TiO2 thin films: Optical and dielectric properties

Transparent nano composite PVA–TiO₂ and PMMA–TiO₂ thin films were prepared by an easy and cost effective dip coating method. Al/PVA–TiO₂/Al and Al/PMMA–TiO₂/Al sandwich structures were prepared to study the dielectric behavior. The presence of metal–oxide (Ti–O) bond in the prepared films was confirmed by Fourier transform infrared spectroscopy. X-ray diffraction pattern indicated that the prepared films were predominantly amorphous in nature. Scanning electron micrographs showed cluster of TiO₂ nanoparticles distributed over the film surface and also there were no cracks and pin holes on the surface. The transmittance of the films was above 80% in the visible region and the optical band gap was estimated to be about 3.77 eV and 3.78 eV respectively for PVA–TiO₂ and PMMA–TiO₂ films by using Tauc's plot. The determined refractive index (n) values were between 1.6 and 2.3. High value of dielectric constant (?′ = 24.6 and ?′ = 26.8) was obtained for the prepared composite films. The conduction in the composite films was found to be due to electrons. The observed amorphous structure, good optical properties and dielectric behavior of the prepared nano composite thin films indicated that these films could be used in opto-electronic devices and in thin film transistors.     

Effect of cobalt doping and annealing on properties of titania thin films prepared by sol-gel process

Undoped and cobalt doped titania (TiO₂) thin films have been prepared on Si(1 0 0) monocrystal and quartz substrate using the sol-gel deposition method and annealed in air at 450, 550, 650, 750, 850, 950 and 1050 °C. Several experimental techniques (AFM, XRD, Raman spectroscopy, XRR, EDX, XPS, XAS, UV-VIS spectroscopy) have been used to characterize these films. Further more the degree of light induced hydrophilicity was estimated by measuring the contact angle of a water droplet on the film. Increase of the annealing temperature and in smaller degree also cobalt doping predispose titania crystallite growth. The rutile phase was detected at lower temperatures in the cobalt doped films than in the undoped titania films. Cobalt in the cobalt doped TiO₂ was seen to be in Co²⁺ oxidation state, mainly in CoTiO₃ phase when films were annealed at temperatures higher than 650 °C. Cobalt compounds segregated into the sub-surface region and to the surface of the titania, where they formed islands. Cobalt doping red-shifted the fundamental absorption edge further into the visible range, however it did not enhance the light induced hydrophilicity of the thin film surface as compared to the undoped titania thin films.     

Optical and electrical properties of nanocrystalline TiO<Subscript>2</Subscript>:Pd semiconducting oxides

Electrical and optical properties of TiO₂:Pd thin films deposited from Ti-Pd mosaic targets sputtered in reactive oxygen plasma have been studied. The properties were investigated for thin films with the Pd amount of 5.5 at. %, 8.4 at. % and 23 at. %. Based on resistivity measurements a drop from 10³ down to almost 10⁻³Ωcm has been recorded when the Pd amount was varied from 5.5 at. % to 23 at. %, respectively. Moreover, it was shown that doping with different amounts of Pd results in the possibility of obtaining both types of electrical conduction: n-type for the TiO₂ with 5.5 at. % and 8.4 at. % of Pd and p-type for the TiO₂ with 23 at. % of Pd thin films. From optical measurements it has been found that as the Pd amount was increased the transmission through the thin films was reduced and position of the fundamental absorption edge was shifted toward a longer wavelength range of up to 600 nm. The optical band gap was calculated for direct and indirect transitions from optical absorption spectra. Structural properties were characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM). The XRD patterns displayed occurrence of the crystalline, TiO₂-rutile for lower Pd amounts (5.5 at. %, 8.4 at. %), while the TiO₂:Pd (23 at. %) thin films displayed XRD-amorphous behaviour. Images obtained from AFM displayed dense, nanocrystalline structure with homogenous distribution of crystallites. Additionally performed secondary ion mass spectroscopy investigation confirmed homogenous distribution of Pd in the whole thickness of the prepared thin films.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

Influences of the iron ion (Fe)-doping on structural and optical properties of nanocrystalline TiO2 thin films prepared by sol-gel spin coating

Titanium dioxide (TiO₂) thin films doping of various iron ion (Fe³⁺) concentrations were deposited on silicon (Si) (100) and quartz substrates by sol-gel Spin Coating technique followed by a thermal treatment at 600 °C. The structure, surface morphology and optical properties, as a function of the doping, have been studied by X-ray diffractometer (XRD), Raman, ultraviolet-visible (UV-vis) and Spectroscopic Ellipsometry (SE). XRD and Raman analyzes of our thin films show that the crystalline phase of TiO₂ thin films comprised only the anatase TiO₂, but the crystallinity decreased when the Fe³⁺ content increased from 0% to 20%. During the Fe³⁺ addition to 20%, the phase of TiO₂ thin film still maintained the amorphous state. The grain size calculated from XRD patterns varies from 29.3 to 22.6 nm. The complex index and the optical band gap (E_g) of the films were determined by the spectroscopic ellipsometry analysis. We have found that the optical band gap decreased with an increasing Fe³⁺ content.     

TiO2 nanoparticle thin film deposition by matrix assisted pulsed laser evaporation for sensing applications

The MAPLE technique has been used for the deposition of nanostructured titania (TiO₂) nanoparticles thin films to be used for gas sensors applications. An aqueous solution of TiO₂ nanoparticles, synthesised by a novel chemical route, was frozen at liquid nitrogen temperature and irradiated with a pulsed ArF excimer laser in a vacuum chamber. A uniform distribution of TiO₂ nanoparticles with an average size of about 10 nm was deposited on Si and interdigitated Al₂O₃ substrates as demonstrated by high resolution scanning electron microscopy-field emission gun inspection (SEM-FEG). Energy dispersive X-ray (EDX) analysis revealed the presence of only the titanium and oxygen signals and FTIR (Fourier transform infra-red) revealed the TiO₂ characteristic composition and bond. A comparison with a spin coated thin film obtained from the same solution of TiO₂ nanoparticles is reported. The sensing properties of the films deposited on interdigitated substrates were investigated, too.     

Influence of terbium on structure and luminescence of nanocrystalline TiO2 thin films

In this work analysis of the structural and optical properties of TiO₂ thin films doped with terbium has been described. Samples were prepared by a high energy reactive magnetron sputtering process under low pressure of oxygen plasma. X-ray diffraction results have shown that different TiO₂ crystal forms have been produced, depending on the amount of Tb dopant. The undoped matrix had rutile structure with crystallites with a size of 8.7 nm, while incorporation of 0.4 at. % of Tb into the film during the sputtering process resulted in anatase structure with bigger crystallites (11.7 nm). Increasing the amount of terbium up to 2 at. % and 2.6 at. % gave rutile structure with crystallites with a size of 6.6 nm for both films. However, Raman spectroscopy has revealed that in the case of TiO₂:(2 at. % Tb), except for the rutile form, the presence of fine-crystalline anatase was observed. Moreover, the lack of Raman peaks shift attests to the lack of stress in the titania lattice of all of the TiO₂:Tb films. This fact indicates localization of Tb3+ ions on the surface of TiO₂ nanocrystals. In the case of optical investigation, results have shown that doping with terbium has a significant influence on the properties of TiO₂, but it does not decrease the high transparency of the matrix. The observed changes of the transmission characteristics were produced only due to modification of the TiO₂:Tb structure. Photoluminescence measurements have shown that emission of light from TiO₂:Tb films occurs when the amount of terbium is 2.6 at. %. Based on the obtained results a scheme of direct energy transfer from titanium dioxide matrix (with rutile structure) to Tb³⁺ ions has been proposed.     

Optical properties of in situ doped and undoped titania nanocatalysts and doped titania sol-gel nanofilms

In this paper we present spectroscopic properties of doped and undoped titanium dioxide (TiO₂) as nanofilms prepared by the sol-gel process with rhodamine 6G doping and studied by photoacoustic absorption, excitation and emission spectroscopy. The absorption spectra of TiO₂ thin films doped with rhodamine 6G at very low concentration during their preparation show two absorption bands, one at 2.3 eV attributed to molecular dimmer formation, which is responsible for the fluorescence quenching of the sample and the other at 3.0 eV attributed to TiO₂ absorption, which subsequently yields a strong emission band at 600 nm. The electronic band structure and optical properties of the rutile phase of TiO₂ are calculated employing a fully relativistic, full-potential, linearized, augmented plane-wave (FPLAPW) method within the local density approximation (LDA). Comparison of this calculation with experimental data for TiO₂ films prepared for undoped sol-gels and by sputtering is performed.     

Evolution of structural and optical properties of rutile TiO2 thin films synthesized at room temperature by chemical bath deposition method

Nanocrystalline thin films of TiO₂ were prepared on glass substrates from an aqueous solution of TiCl₃ and NH₄OH at room temperature using the simple and cost-effective chemical bath deposition (CBD) method. The influence of deposition time on structural, morphological and optical properties was systematically investigated. TiO₂ transition from a mixed anatase–rutile phase to a pure rutile phase was revealed by low-angle XRD and Raman spectroscopy. Rutile phase formation was confirmed by FTIR spectroscopy. Scanning electron micrographs revealed that the multigrain structure of as-deposited TiO₂ thin films was completely converted into semi-spherical nanoparticles. Optical studies showed that rutile thin films had a high absorption coefficient and a direct bandgap. The optical bandgap decreased slightly (3.29–3.07 eV) with increasing deposition time. The ease of deposition of rutile thin films at low temperature is useful for the fabrication of extremely thin absorber (ETA) solar cells, dye-sensitized solar cells, and gas sensors.