CR环二极磁铁的磁场优化

FAIR项目中的CR环二极磁铁对磁场积分场的误差分布要求很高,通过削斜与加载镜像板的方法是优化磁场的主要方法,文中介绍了对二极磁铁优化方法和对它的处理方法.利用削斜的方法来改变二极磁铁积分场的误差分布,通过复杂的削斜,已将其高场的误差分布优化到±2×10-4.加镜像板的方法主要适合高场,而对低场的调节不明显.另外处理方法的选取对结果的影响也很大,文中对两种方法作了比较.优化模拟计算软件采用的是专门的磁场计算工具OPERA.     

冷却储存环主环注入线二极磁铁测量

 介绍了兰州重离子加速器冷却储存环工程主环注入线二极磁铁的测磁系统和测磁结果。着重分析了垫补线圈和极头削斜两种手段对C型弯曲二极磁铁积分磁场径向分布均匀度的调节效果。并且分析了TOSCA三维磁场计算程序与实际测量结果之间的误差及其产生的原因。     

CSNS/RCS交流二极磁铁研制关键技术

针对交流二极磁铁的磁场特性和涡流问题,利用电磁场分析软件对磁铁进行了优化设计和温度场计算,确定了交流二极磁铁关键技术的方案。对交流二极磁铁极头端面采用了罗高斯基曲线和谐波削斜的方法来提高磁铁磁场质量;对铁芯端部和端板进行开槽优化设计,有效切断磁铁端部主要的涡流回路,降低了磁铁温升;磁铁线圈采用铝绞线导线进行绕制,以减少磁铁线圈内的涡流损耗。最后,通过对样机磁铁的测试,磁场均满足物理要求,磁铁温度也控制在安全范围内。     

CSR60°二极C型铁磁场特性的研究

兰州重离子加速器冷却储存环主环注入线二极C型磁铁首次采用了磁极头中埋置垫补线圈调整磁场均匀度的设计.在其磁场测量中,使用了点测和积分测量的方法对其各方面特性参数进行了测量,并对积分场的测量结果以及内置垫补线圈对均匀场的垫补效果进行了详细的非线性分析.     

HIRFL-CSRe二极铁积分磁场测量

 介绍了兰州重力加速器冷却储存环实验环二极磁铁积分长线圈测磁装置的构成,描述了实验环二极铁的分散性测量、横向分布测量、传递函数等测量内容及测量方法。实验环二极铁采用不断地加减硅钢铁片垫补和加调整线圈电流的方法来调整二极磁铁的有效长度来改变分散性。通过垫补和测量,二极磁铁的分散性在优化磁场时达到±2×10^-4。同时给出了二极铁的横向分布和传递函数的测量结果。对二极铁的设计和加工进行了修正。     

FAIR项目Super-FRS超导二极磁铁端部优化

介绍了Super-FRS超导二极磁铁的磁场优化和端部削斜方案,采用OPERA软件对活极头进行削斜计算,得出合理的活极头尺寸,使各场下的积分均匀度在要求范围内达到了±2×10-4。最后将计算的积分场均匀度与磁场测量的结果进行比较,结果吻合得较好,验证了这种端部活极头优化计算方法的正确性。 The end optimization of dipole magnet of Super-FRS for FAIR by OPERA 3D has been introduced in this paper. By using a complicated chamfer, the integral field homogeneity which is better than 2×10-4 can be obtained. In addition, the paper also introduced the comparison between the magnetic field measurement result and calculation one, which confirms the method of the removable pole end chamfer very well.     

HIAF-BRing快脉冲二极磁铁磁场测量系统

介绍了强流重离子加速器装置HIAF(High Intensity heavy-ion Accelerator Facility)项目增强器BRing(Booster Ring)快脉冲二极磁铁的性能指标、测量要求和测量方法,描述了快脉冲二极磁铁稳态磁场测量系统及动态磁场测量系统的构成。在稳态磁场测量中,为提高积分磁场测量精度和测量效率,长线圈测量系统采用了on fly技术;在动态磁场测量中,研制了用于磁场延迟及磁场畸变测量的矩阵线圈。通过样机磁铁的测量,完成了测量系统的性能指标验证和磁铁的稳态磁场测量。实测结果表明,样机磁铁的设计和制造均达到了预期指标,并依据测量数据完成了磁铁的二次削斜。     

真空盒对二极铁场均匀性影响的研究

通过计算机模拟计算与实验相结合, 讨论了真空盒磁导率对二极磁铁磁场分布的影响. 结果表明当真空盒磁导率μ_r≠1时, 真空盒将影响磁铁磁场分布, 在磁场均匀性要求很高时, 必须考虑真空盒的材料与尺寸对磁场均匀性的影响.     

高精度多探头磁场测量系统

兰州重离子研究装置的磁场测量系统已于1983年10月建立. 多探头长臂上装有94个霍尔片. 测磁支架采用长臂、动环和定环组成的以加速器几何中心为原点的极坐系结构. 由小型计算机承担自动控制和数据的获取与处理工作. 对16KG磁场, 本系统的测量重复性好于±5×10^－5, 测量精确度估计为±1×10^－4. 测量速度约为每分钟188个数据.     

中国散裂中子源磁铁系统和样机研制

中国散裂中子源(China Spallation Neutron Source, CSNS)快循环同步加速器(Rapid Cycling Synchrotron, RCS)磁铁由24块二极磁铁、48块四极磁铁、16块六极磁铁和若干斜四极磁铁以及校正磁铁组成, 其中二极磁铁和四极磁铁是带直流偏置的25Hz正弦交流励磁, 铁芯和线圈导体将产生不可忽视的涡流效应. 为了积累批量生产磁铁的制造经验, 探索磁铁后期处理和磁场测量方法, 已完成了中空水冷铝绞线试样线圈的研制, 启动了二极磁铁和四极磁铁样机的研制. 本文将对相关进展进行介绍.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.