盐酸催化合成α-萘乙酸甲酯

以α-萘乙酸、甲醇为原料,以浓盐酸为催化剂,通过酯化反应合成了植物生长调节剂萘乙酸甲酯。通过正交设计讨论了醇酸摩尔比、催化剂用量、反应时间等因素对酯化产率的影响。在α-萘乙酸50mmol,n(甲醇)：n(α-萘乙酸)=25,催化剂用量为α-萘乙酸质量的17％,反应时间2．0h,酯化温度65℃～69℃的最佳反应工艺条件下,产率97．4％。     

TiSiW12O40／TiO2催化合成葡萄糖五丁酸酯的研究

首次报道了新型催化剂TiSiW12O40/TiO2催化酯化合成葡萄五丁酸酯,考察了糖酸比、催化剂用量、反应时间、反应温度诸因素对产率的影响。实验表明,TiSiW12O40/TiO2是合成葡萄糖五丁酸酯的良好催化剂。最佳反应条件为：糖酸摩尔比1：6,催化剂的用量为反应物料总量的2.0%,酯化反应时间为2.0h,反应温度90-95℃。反应产率可达85.4%。     

固体超强酸ZrO_2/S_2O_8~(2-)催化合成乙酸正己酯

以固体超强酸ZrO2/S2O2-8为催化剂,乙酸和正己醇为原料合成了乙酸正己酯,考察了反应条件对酯化率的影响.结果表明,最佳反应条件为:醇酸摩尔比1.4,催化剂用量0.5g(当乙酸用量为0.1mol时),带水剂苯15mL,在110～118℃反应1.5h,其酯化率达92%以上.该方法的优点是酯化率高,催化剂可重复使用且基本不腐蚀设备.     

ZnMn2O4纳米催化剂制备及催化合成乙酸正丁酯

本文以共沉淀法制备了四方晶系锌锰复合氧化物ZnMn2O4纳米催化剂。采用X射线粉末衍射(XRD)和透射电子显微镜(TEM)测试技术对样品进行了分析表征,结果表明所合成的催化剂为粒径均匀的纳米粒子,平均粒径在20-50 nm,具有较好的分散性。实验考察了所制备的ZnMn2O4纳米催化剂对乙酸和正丁醇酯化反应的催化活性,表明ZnMn2O4对乙酸正丁酯的合成有较高的催化活性;探讨了催化剂焙烧温度、催化剂用量、酸醇摩尔比以及反应时间对酯化率的影响,确定了适宜的酯化反应条件,以焙烧温度为300 ℃制备的ZnMn2O4为催化剂,在催化剂用量为0.3%(以反应物总质量计)、酸醇摩尔比n(酸):n(醇)=1.8:1、反应时间为4 h、酯化反应温度120 ℃的条件下,酯化率可达92.53%。     

磷钨酸催化合成丙烯酸丁酯

用磷钨酸为催化剂 ,由丙烯酸和丁醇直接酯化合成了丙烯酸丁酯。研究了醇 /酸比、酯化时间、催化剂用量、带水剂用量对酯化率的影响 ;选择了最佳反应条件 ,重复反应酯化率达到 95 %以上。     

固体超强酸ZrO2/S2O28-催化合成乙酸正己酯

以固体超强酸ZrO2／S2O8^2-为催化剂，乙酸和正己醇为原料合成了乙酸正己酯，考察了反应条件对酯化率的影响,结果表明，最佳反应条件为：醇酸摩尔比1．4，催化剂用量0．5g(当乙酸用量为0．1mol时)，带水剂苯15mL，在110-118℃反应1．5h，其酯化率达92％以上．该方法的优点是酯化率高，催化剂可重复使用且基本不腐蚀设备．     

固体酸预处理高酸值油脂降低酸值

通过沉淀、回流和浸渍分别制备了Al、Ga掺杂的SO 2-4/ZrO2固体酸催化剂,利用该促进型固体酸催化剂酯化预处理高酸值油脂,考察了固体酸焙烧温度、醇油摩尔比等因素对酯化反应的影响. 结果表明,该类型固体酸对高酸值油脂具有良好的酯化反应活性,其中600 ℃焙烧的Ga2O3/SO 2-4/ZrO2在67 ℃下,醇与油摩尔比为30: 1,催化剂用量为4%,对初始酸值为32的油脂进行酯化反应,经8 h反应,油脂酸值降为4.1,有利于后续用碱性催化剂对处理后的油脂进行酯交换反应生成生物柴油.     

二氧化硅负载硫酸氢钠催化合成壬酸乙二醇单酯

研究了以二氧化硅负载硫酸氢钠为催化剂,壬酸和乙二醇为原料合成壬酸乙二醇单酯的工艺.考察了酸醇物质的量、催化剂用量、反应时间、反应温度等对壬酸酯化率的影响,结果表明,合成壬酸乙二醇单酯的优化条件为:壬酸与乙二醇的物质的量为1∶3,催化剂的用量为反应物料总质量的5%,反应时间为4h,反应温度为90℃,在此条件下,酯化率可达92%以上,通过红外光谱验证了目标产物.催化剂具有一定的重复使用活性.     

乙酸异丙酯的合成

以乙酸和异丙醇为原料,硫酸氢钠为催化剂,合成了乙酸异丙酯;考察了反应时间、酸醇比、催化剂用量、带水剂用量对酯化率的影响,确定了最佳酯化反应条件:反应时间60min,酸醇的物质的量的比1∶0.8,催化剂用量0.8g,带水剂用量8mL.在最佳反应条件下,酯化率最高可达84.3%.     

磷酸钛固载磷钨酸非均相催化合成异戊酸己酯

通过在300℃下焙烧2h制备了磷酸钛固载15%磷钨酸H3PW12O40(简记为HPW)非均相酯化催化剂HPW/Ti3(PO4)4;采用红外光谱仪分析了催化剂的结构;基于异戊酸与正己醇的酯化反应考察了催化剂用量、n(正己醇)∶n(异戊酸)、反应时间、带水剂种类和催化剂重复使用性能等因素对酯化率的影响.结果表明,该催化剂催化合成异戊酸己酯的适宜反应条件为:0.2mol异戊酸,催化剂用量0.6g,n(正己醇)∶n(异戊酸)=1.6∶1,反应时间4.5h,环己烷10mL;相应的酯化率达95.1%.与此同时,该催化剂循环利用6次后酯化率不低于84%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.