Sub-Tg mechanical relaxation of a La55Al25Ni20 amorphous alloy

Dynamic mechanical properties of an amorphous La₅₅Al₂₅Ni₂₀ alloy were measured by a forced oscillation method in the temperature range from room temperature to 453 K, just below the glass transition temperature (T_g = 481 K). The internal friction at a constant frequency 62.8 rad/s of this alloy showed a peak at about 400 K and the peak position shifts with frequency. Structural relaxation reduces the magnitude of the relaxation peak but has little affect on the peak position. Using the time-temperature superposition process, master curves for storage E′ (ln ω) and loss E″ (ln ω) moduli are constructed. Activation energy of the relaxation obtained from shift factors is low, 100 kJ/mol, which is close to that for diffusion of the Al in Al and Ni in Al. The relaxation spectra are very broad with a half width of 2 3 decades.     

The observation of two glass transitions in the dynamic mechanical properties of a La55Al25Ni20 amorphous alloy

The glass transition behavior of a La₅₅Al₂₅Ni₂₀ amorphous alloy was examined through the changes in the storage, E′, and loss, E″, moduli obtained by a forced oscillation method. Two distinguishable relaxation peaks are observed in the glass transition region, although these are not resolved in calorimetric measurements. At a frequency of 62.8 rad/s, E″ shows two peaks at 483 and 507 K. As the frequency decreases, the splitting of the two peaks becomes distinct and their peak temperatures shift to a lower value. The change in E″ with frequency also shows the two relaxation peaks. A master curve of E″ is derived by using the time-temperature superposition process. This is the first master curve for the relaxation spectrum in the glass transition region for amorphous alloys. The activation energies evaluated from the shift factors are 400 and 550 kJ/mol for the lower and higher temperature peaks, respectively.     

A SAXS observation of the crystallization of an Al85Y10Ni5 amorphous alloy in the supercooled liquid state

The medium-range structure of a heat-treated Al₈₅Y₁₀Ni₅ amorphous alloy was investigated by small-angle X-ray scattering, calorimetric analysis, wide-angle X-ray diffraction and transmission electron microscope measurements. It is observed that crystalline particles having a definite boundary are precipitated by annealing at supercooled liquid temperatures and that most of the precipitates consist of the Al fcc crystalline phase. The integrated intensities of the small-angle scattering and the Guinier radii of the precipitates increase on annealing for time duration <5.4 ks. However, as the annealing time becomes > 5.4 ks, the integrated intensities and the Guinier radii are invariant, i.e., growth of the precipitates ceases. After annealing for 518.4 ks, the diameters of the precipitates exhibit a narrow distribution centered around 200 Å.     

Influence of outphase Cu50Ti50 amorphous alloy addition on microstructural evolution of mechanically alloyed Zr66.7Ni33.3 amorphous alloy

The influence of outphase Cu₅₀Ti₅₀ amorphous alloy addition on microstructural evolution of Zr_66.7Ni_33.3 amorphous alloy has been investigated using a mechanical alloying method. It has been found that the milling induced microstructural evolution is related to the change of peak positions of the first maximum on X-ray diffraction patterns of the as-obtained amorphous alloys. With increasing milling time, the 3 wt.% Cu₅₀Ti₅₀ addition can give rise to the cyclic amorphization transformation of the as-milled alloy. The mechanical stability of the mixing amorphous phase can be greatly enhanced with increasing Cu₅₀Ti₅₀ addition up to 10 wt.%. Moreover, the addition of outphase Cu₅₀Ti₅₀ amorphous alloy not only increases the onset crystallization temperature of Zr_66.7Ni_33.3 amorphous alloy but also alters its crystallization mode. The effect of outphase amorphous addition on the mechanical stability of the Zr_66.7Ni_33.3 amorphous phase has been discussed based upon the bond order theory.     

Thermal stability of amorphous Mg50Ni50 alloy produced by mechanical alloying

Amorphous Mg₅₀Ni₅₀ alloy was produced by mechanical alloying (MA) of the elemental powders Mg and Ni using a SPEX 8000D mill. The alloyed powders were microstructurally characterized by X-ray diffraction (XRD). The thermal transformation of amorphous Mg₅₀Ni₅₀ into stable intermetallics (Mg₅₀Ni₅₀ → remaining amorphous + Mg₂Ni → Mg₂Ni + MgNi₂) was analyzed using the Kissinger and isoconversional methods based on the non-isothermal differential scanning calorimetry (DSC) experiments. The apparent activation energies (E_a) and the transformation diagrams, temperature-time-transformation (T-T-T) and temperature-heating rate-transformation (T-HR-T), were obtained for both processes. A good agreement was observed between the calculated transformation curves and the experimental data, which verifies the reliability of the method utilized.     

Short-range order in ultrafine powder of an amorphous (Fe7Ni3)69B31 alloy

The short-range order structure of ultrafine powder of an amorphous (Fe₇Ni₃)₆₉B₃₁ alloy has been studied by ZAFS. The particles with diameters 1.7–15.3 nm are prepared by chemical reduction. The fact that the local environments around Fe or Ni are not the same suggests that there is chemical short-range order in this material. The mean distances of near neighbors surrounding an Fe and a Ni atom are shorter than those in amorphous Fe₈₀B₂₀ ribbon. The XANES spectra also show some differences between these two amorphous alloys. These indicate that the interaction between near neighbors is stronger in this amorphous ultrafine powder than in bulk amorphous material.     

Length and density changes of amorphous Pd40Cu30Ni10P20 alloys due to structural relaxation

The density changes of bulk amorphous Pd₄₀Cu₃₀Ni₁₀P₂₀ due to structural relaxation under isothermal heat treatment were measured using the buoyancy method. The corresponding length changes of amorphous Pd₄₀Cu₃₀Ni₁₀P₂₀ ribbons applying non-isothermal heat treatment are determined applying dilatometry. The measured density changes Δρ(T=const.,t)/ρ_o as a function of isothermal heat treatment increase close to the glass transition up to 0.18%. The measured density changes as a function of temperature and time are furthermore reversible. The experimental data validate the model predictions of the free volume model for length and density changes of amorphous alloys due to structural relaxation applying isothermal and non-isothermal heat treatment.     

On mechanisms of structural relaxation in a Pd48Ni32P20 glass

Structural relaxation processes are investigated calorimetrically for a pre-conditioned Pd₄₈Ni₃₂P₂₀ glass over a wide temperature range from well below to just above the glass transition. The low temperature anneals further stabilize the glassy structure. Upon heating, the annealed sample shows an excess endothermic specific heat ΔC_p above the annealing temperature and completely recovers the initial enthalpy before any manifestation of glass transition, T_g. Significantly the ΔC_p peak evolves in a continuous manner with annealing time. A physically reasonable activation energy spectrum $\text{N}{}_0{}^1\text{(Q)}$ is obtained with the proper choice of coupling constants which are dependent on annealing temperature. Results suggest the existence of localized relaxation modes which do not contribute to macroscopic flow. A concept of distribution in glass transition temperatures H(T_g,m) is conceived to account for the reversible relaxation with temperature. A model glass transition based on percolation theory is proposed and is found to reproduce the calorimetric relaxation phenomena well.     

The structural relaxation and glass transition of La---Al---Ni and Zr---Al---Cu amorphous alloys with a significant supercooled liquid region

An amorphous phase with a wide supercooled liquid region, > 50 K, was found to form over wide composition ranges in the La---Al---Ni and Zr---Al---Cu systems. The largest values for the temperature span between the crystallization temperature, T_x, and the glass transition temperature, T_g, ΔT_x(-T_x−T_g), are 69 K for La₅₅ Al₂₅Ni₂₀ and 88 K for Zr₆₅Al_7.5Cu_27.5. The structural relaxation behavior on annealing was examined for the two amorphous alloys with the largest ΔT_x values. The magnitude of the structural relaxation increases gradually with increasing annealing temperature, T_a, and then rapidly in the T_a range slightly below T_g and decreases significantly on annealing T_g. The rapid increase in the magnitude of the structural relaxation on annealing near T_g is due to the glass transition. The single-stage structural relaxation indicates that there is no distinct difference in relaxation times (atomic bonding forces) between the constituent atoms in the two metal-metal-type amorphous alloys. The existence of an optimum bonding state is thought to cause the wide supercooled liquid region for the two amorphous alloys.     

Electron microscopic study of the crystallization kinetics of the amorphous alloy Pd80Si20

Amorphous Pd₈₀Si₂₀ foils, prepared by the rapidly rotating mill device method, were quenched from the liquid state, temperatures of the melt being 1100, 1500 and 1600°C. The foils were linearly heated at a rate of 1.5 °C/min over a temperature range of 20–600°C. The structural changes were observed by methods of optical microscopy, transmission electron microscopy and electron diffraction. The beginning of crystallization of the amorphous phase is affected by the temperature of the melt. The crystallization of the amorphous phase was terminated at a temperature of 390–400°C. Silicides Pd₉Si₂ and Pd₃Si, the morphology of which varied with temperature, were formed during crystallization.     

Influence of Gd and Fe on crystallization of Al87Y5Ni8 amorphous alloy

Crystallization of amorphous Al-based alloys (Al-Y-Gd-Ni-Fe) was investigated by applying differential scanning calorimetry (DSC), X-ray diffraction (XRD) and high resolution electron microscopy (HREM). It was shown that the crystallization in the examined alloys proceeds in three stages (DSC maxima). The two first stages are attributed to formation of solid solution of fcc Al(RE) nanograins in amorphous matrix. In the third stage the precipitation of ternary compound Al₁₉Ni₅RE₃ of the orthorhombic Al₁₉Ni₅Gd₃-type structure was observed. A partial substitution of Ni by Fe causes a change of stoichiometry and crystal structure of the ternary compounds: Al₈TM₄RE (TM = Fe, Ni; RE = Y, Gd) of the tetragonal ThMn₁₂ (Al₈Mn₄Ce)-type structure. A partial replacing of Y atoms by Gd in the Al₈₇Y₅Ni₈ based alloy shifts the Al(RE) nanocrystallization to lower temperatures. In contrast to this a partial replacing of Ni by Fe shifts the nanocrystallization to higher temperatures.     

Reverse Monte Carlo simulations of an amorphous Cr25Nb75 alloy produced by mechanical alloying

The local atomic structure of an amorphous Cr₂₅Nb₇₅ alloy produced by mechanical alloying was determined using only one X-ray total structure factor S(K) as input data for reverse Monte Carlo simulations. The results showed that the amorphous alloy has a local atomic structure similar to that predicted by the additive hard sphere model for a Cr and Nb mixture with same composition of the alloy, and quite different of those found in the cubic and hexagonal Cr₂Nb crystals.     

Physical properties of amorphous Ge20Sb25−xBixSe55 thin films

The influence of substitution of Sb atoms by Bi atoms on the electrical and optical properties of thin films of the Ge₂₀Sb_25−xBi_xSe₅₅ [0x15] system are reported. Results of dc conductivity and thermoelectric power measurements between 150 and 450 K show that the Ge---Sb---Se system is chemically modified by addition of large concentrations of Bi atoms between X=5 and X=10 at.%). A transition from p-type for Sb-doped to n-type for Bi-doped films and a decrease of resistivity is observed. The absorption edge shifts to shorter wavelength, thereby decreasing the optical band gap of the system. Compositional dependences of electrical conductivity, thermoelectric power, and the appearance of n-type conduction are discussed from the stand point of chemical bonds formed in the films and related to the defect states produced due to incorporation of Bi atoms in high concentrations. The coexistence of band and hopping conduction is proposed. The ac conductivity in 0.1–10.0 kHz frequency and 150–450 K temperature range was found to obey a power law σ(ω, T) = Aω^s. The results were interpreted in terms of Elliott's theory, which assumes correlated barrier hopping (CBH) between the charged defect centres. It was found that computed results from the CBH model and experimental one are qualitative agreement for the present materials.     

Study on crystallization kinetics of Al65Cu20Ti15 amorphous alloy

The crystallization behavior and thermal stability of amorphous phases of Al₆₅Cu₂₀Ti₁₅ alloy obtained by mechanical alloying were investigated by using in-situ X-ray diffraction and differential scanning calorimetry (DSC) under non isothermal and isothermal conditions. The result of a Kissinger analysis shows that the activation energy for crystallization is 1131 kJ/mol. The higher stability against crystallization of Al₆₅Cu₂₀Ti₁₅ amorphous alloy is attributed to the stronger interaction of atoms in the Al-Cu-Ti system and formed of complicated compound like Al₅CuTi₂ and Al₄Cu₉ as primary phases. The isothermal crystallization was modeled by using the Johnson-Mehl-Avrami (JMA) equation. The Avarami exponents suggest that the isothermal crystallization is governed by a three-dimensional diffusion-controlled growth.     

Growth and characterization of ferromagnetic shape memory alloy Co50Ni20FeGa29 single crystals

Single crystals of Co₅₀Ni₂₀FeGa₂₉ with B2 phase have been obtained in a deep supercooling condition. The interface-facets and the segregation effect lead to the formation of ordered defects that store a directional internal stress. These defects give to a large energy barrier that leads to a very sharp martensitic transformation within a temperature window of only 2 K. The single crystals show good shape memory effect and superelasticity, which are anisotropic between the growth direction [0 0 1] and its equivalent direction [0 1 0]. The anisotropic behaviors are attributed to the directional internal stress caused by the ordered defects.     

Crystallization kinetics of the Zr61Al7.5Cu17.5Ni10Si4 alloy using isothermal DSC and TEM observation

The crystallization behavior and microstructure development of the Zr₆₁Al_7.5Cu_17.5Ni₁₀Si₄ alloy during annealing were investigated by isothermal differential scanning calorimetry, X-ray diffractometry and transmission electron microscopy. During isothermal annealing of the Zr₆₁Al_7.5Cu_17.5Ni₁₀Si₄ alloy at 703 K, Zr₂Cu crystals with an average size of about 5 nm were first observed during the early stages (30% crystallization) of crystallization by TEM. The Zr₂Cu crystal size increased with annealing time and attained an average size of 20 nm corresponding to the stage of 80% crystallization. In addition, the change in particle size with increasing annealing time exhibited a linear relationship between grain growth time and the cube of the particle size for the Zr₂Cu type crystalline phase. This indicates that the crystal growth of the Zr₆₁Al_7.5Cu_17.5Ni₁₀Si₄ alloy belongs to a thermal activated process of the Arrhenius type. The activation energy for the grain growth of Zr₂Cu is 155 ± 20 kJ/mol in the Zr₆₁Al_7.5Cu_17.5Ni₁₀Si₄ amorphous alloy. The lower activation energy for grain growth in compared to that for crystallization in Zr₆₅Cu₃₅ 440 kJ/mol crystal corresponds to the rearrangement of smaller atoms in the metallic glass, Al or Si (compare to Zr).     

Crystallization behaviour of an amorphous Ti50Be40Zr10 alloy

The crystallization behaviour of an amorphous Ti₅₀Be₄₀Zr₁₀ alloy during a continuous heating mode from room temperature to 973 K and isothermal annealing at temperatures above the glass transition temperature is examined by differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS) measurement and large-angle X-ray diffractometry (LAXD). DSC indicated two well-defined exothermic peaks, a slight shoulder at the higher temperature side of the second peak and a small heat evolution at higher temperature. The Kissinger plot for the first and the second peak gives a straight line, from which the apparent activation energy is estimated to be 269 and 413 kJ/mol respectively; the enthalpies for the first and second crystallization process are 1.04 kJ/mol and 4.39 kJ/mol for a heating rate of 20 K/min. The SAXS intensities increase sharply after annealing at about 673 K (corresponding to the first peak in the DSC curves); the scattering is due to the formation of fine-scale crystalline Ti particles by the LAXD. The size of the particles does not change significantly while the number of scattering particles increases, indicating that the reaction is almost nucleation controlled and the growth is very limited. Another crystalline phase would appear in addition to the Ti particles on annealing at temperatures above about 753 K (corresponding to the second peak in the DSC curves), where the SAXS intensities decrease compared with those for only the first-stage of crystallization. The crystalline phase might be a metastable cubic phase with the lattice parameter a₀?0.2994 nm.The sequence in the crystallization of the initial non-crystalline material is amorphous → microcrystalline (MS I) → crystalline (MS II; S III), although the structure of crystalline phase in the final stage (S III) was not identified. It is also likely that cold-rolling does not have a perceptible effect on the crystallization behaviour of the present amorphous alloy.     

Heat capacity of Pd40Ni40P20 in the deeply undercooled liquid state determined by relaxation experiments in the glass transition region

An indirect method is presented which allows for the heat capacity determination of deeply undercooled melts at temperatures in the glass transition region, which are inaccessible to continuous calorimetric measurements. The method is based only on the unique relaxation behavior of glass-forming liquids in the transition region, and thus is generally applicable for vitreous systems. Here it is illustrated by measurements of the specific heat of deeply undercooled Pd₄₀Ni₄₀P₂₀, a metallic bulk-glass former, resulting in a considerable approach of the measurements towards the isentropic limit. Additionally, the consequent application of this method allowed for the determination of the dependence of the glass temperature on the cooling rate during vitrification, yielding a linear relation between the glass temperature and the logarithm of the cooling rate, as observed for several non-metallic glass-forming systems.     

Pressure and heating rate dependence of the crystallization temperature for amorphous (Fe65Ni35)75P16B6Al3 and Ti50Be40Zr10

The crystallization temperature, T_x, was determined at constant heating rate, $\text{R =}\text{T}\text{?}\text{? 7}\text{K min}{}^{\mathrm{?1}}$, by monitoring the electrical resistance. Such experiments were carried out under pressures up to 2.5 GPa, and the resulting dT_x/dP was 15.9 K GPa^?1 for (Fe₆₅Ni₃₅)₇₅P₁₆B₆Al₃ and 8.7 K GPa^?1, 8.1 K GPa^?1 for the two crystallization processes in Ti₅₀Be₄₀Zr₁₀. The activation energies of crystallization under atmospheric pressure were obtained from measurements of T_x at rates from 0.05 K min^?1 ?55 K min^?1, analysed by plotting ln(T_x²R^?1) versus T_x^?1.     

XPS characterization of corrosion films formed on the crystalline, amorphous and nanocrystalline states of the alloy Ti60Ni40

X-ray photoelectron spectroscopy investigations were carried out on the crystalline, amorphous and nanocrystalline states of the alloy Ti₆₀Ni₄₀ after corrosion test in 1 M HNO₃ aqueous medium using potentiodynamic polarization method. Polarization plots revealed that the nanocrystalline state is more corrosion resistant than the amorphous and crystalline states of the alloy Ti₆₀Ni₄₀. The XPS characterization of the oxide film formed after corrosion tests revealed that a multiple phase oxide film is formed on the crystalline and amorphous specimens of the alloy Ti₆₀Ni₄₀ consisting of Ti²⁺, Ti³⁺ and Ti⁴⁺ species along with some unoxidized Ti in metallic form (Ti⁰) in the case of crystalline specimen whereas the oxide film formed on nanocrystalline specimen consists of only Ti²⁺ and Ti⁴⁺ species. The high corrosion resistance of nanocrystalline state is attributed to the presence of fewer oxide species in the oxide film than that of the amorphous and crystalline states of the alloy Ti₆₀Ni₄₀.