One-dimensional diffusion of vacancies on Sr/Si(100)-c(2×4) surface

An Sr/Si(100)-c(2×4) surface is investigated by high-resolution scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). The semiconductor property of this surface is confirmed by STS. The STM images of this surface shows that it is bias-voltage dependent and an atomic resolution image can be obtained at an empty state under a bias voltage of 1.5 V. Furthermore, one-dimensional (1D) diffusion of vacancies can be found in the room-temperature STM images. Sr vacancies diffuse along the valley channels, which are constructed by silicon dimers in the surface. Weak interaction between Sr and silicon dimers, low metal coverage, surface vacancy, and energy of thermal fluctuation at room temperature all contribute to this 1D diffusion.     

Initial growth stages of manganese films on the Si(100)2 × 1 surface

Initial growth stages of manganese films on the Si(100)2 × 1 surface at room temperature have been investigated using high-energy-resolution photoelectron spectroscopy, and the dynamics of the variation in their phase composition and electronic structure with the coverage growth has been revealed. It has been shown that the interfacial manganese silicide and the film of the solid solution of silicon in manganese are sequentially formed under these conditions on the silicon surface. The growth of the metal manganese film starts after the deposition of ～0.9 nm Mn. Segregation of silicon on the film surface is observed in the range of coverages up to 1.6 nm Mn.     

Adsorption and diffusion of Si adatom near single-layer steps on Si surface

By use of the empirical tight-binding （ETB） method, the adsorption and diffusion behaviours ot single sllmon adatom on the reconstructed Si（100） surface with single-layer steps are simulated. The adsorption energies around the SA step, nonrebonded SB step, rebonded SB step, and rough SB step with a kink structure are specially mapped out in this paper, from which the favourable binding sites and several possible diffusion paths are achieved. Because of the rebonded and kink structures, the SB step is more ~uitable for the attachment of Si adatom than the SA step or defective surface.     

A first-principles study on initial processes of a Ni adatom on the H-terminated Si(0 0 1)-(2×1) surface

We studied the adsorption, surface diffusion, and penetration, i.e. the initial processes of a Ni adatom on the H-terminated Si(001)-(2×1) surface by the first-principles theoretical calculations. As concerns the adsorption, two different types were found. When Ni is deposited onto the Si dimer row, it once captures H from the dimer Si, though it eventually returns H, with no activation energy barrier. Then, Ni moves to the most stable site, which is the off-centered bridge (B) site between the dimer rows, with the activation energy of 0.65 eV. On the other hand, Ni deposited between the dimer rows captures no H and moves to the B site without the energy barrier. Thus an adsorbed Ni atom invariably arrives at the most stable B site at the room temperature. As for the surface diffusion, it needs the activation energies of 0.66 and 1.19 eV for Ni to migrate from the B site in the directions parallel and perpendicular to the dimer row, respectively. Therefore, we concluded that the surface diffusion of Ni is restricted in the valley between the dimer rows at the room temperature. Furthermore, since the penetration of Ni is blocked on this surface, it was also concluded that the surface hydrogenation suppresses silicidation.     

One-dimensional diffusion of vacancies on an Sr/Si(100)-c(2×4) surface

An Sr/Si(100)-c(2×4) surface is investigated by high-resolution scanning tunneling microscopy(STM) and scanning tunneling spectroscopy(STS).The semiconductor property of this surface is confirmed by STS.The STM images of this surface shows that it is bias-voltage dependent and an atomic resolution image can be obtained at an empty state under a bias voltage of 1.5 V.Furthermore,one-dimensional(1D) diffusion of vacancies can be found in the room-temperature STM images.Sr vacancies diffuse along the valley channels,which are constructed by silicon dimers in the surface.Weak interaction between Sr and silicon dimers,low metal coverage,surface vacancy,and energy of thermal fluctuation at room temperature all contribute to this 1D diffusion.     

Theoretical simulation of STM image of C60 molecules on Si(100)-(2 × 1) surface

Theoretical simulation of STM image of C₆₀ molecules on Si(100)-(2 × 1) surface was performed by the DV-Xα-LCAO method. The results excellently reproduced the internal stripe pattern of the STM image of C₆₀ observed by experiment. We confirm that it is the interaction between C₆₀ and the Si substrate which causes this internal structure.     

Dangling-bond logic gates on a Si(100)-(2 × 1)-H surface

Atomic-scale Boolean logic gates (LGs) with two inputs and one output (i.e. OR, NOR, AND, NAND) were designed on a Si(100)-(2 × 1)-H surface and connected to the macroscopic scale by metallic nano-pads physisorbed on the Si(100)-(2 × 1)-H surface. The logic inputs are provided by saturating and unsaturating two surface Si dangling bonds, which can, for example, be achieved by adding and extracting two hydrogen atoms per input. Quantum circuit design rules together with semi-empirical elastic-scattering quantum chemistry transport calculations were used to determine the output current intensity of the proposed switches and LGs when they are interconnected to the metallic nano-pads by surface atomic-scale wires. Our calculations demonstrate that the proposed devices can reach ON/OFF ratios of up to 2000 for a running current in the 10 μA range.     

STM study of structural changes on Si(100)2×1-Sb surface induced by atomic hydrogen

Using scanning tunneling microscopy (STM) and low energy electron diffraction (LEED), we have studied the structural changes of the Si(100)2×1-Sb surface caused by hydrogen adsorption at both room temperature (RT) and 300°C. We have found that the ordering of a 2×1-Sb surface is more stable against atomic hydrogen exposure at 300°C than at RT, and that some Sb atoms desorb during atomic hydrogen exposure at 300°C. However, upon hydrogen exposure at both temperatures, we have observed neither three-dimensional islands nor the hydrogen terminated Si substrate which were reported for hydrogen interaction with the other metal/Si systems. On the 2×1-Sb surface exposed to atomic hydrogen of 1000 L at RT followed by 550°C annealing, long bright lines similar to those reported for the Bi/Si(100) system have also been found.     

Atomic and electronic properties of tert-butanol on the Si(001)-(2×1) surface

The atomic and electronic properties of the adsorption of tert-butanol [(CH₃)₃OH] molecule on the Si(001)-(2×1) surface have been studied by using the ab-initio density functional theory (DFT) based on pseudopotential approach. We have found that tert-butanol bonded the Si(001) surface by oxygen atom, cleaving a O–H bond and producing a Si-H bond and tert-butoxy surface species. We have also investigated the influence of chemisorption of tert-butanol on the electronic structure of the clean Si(001)-(2×1) surface. Two occupied surface states situated entirely below the bulk valence band maximum have been identified, which means that the clean Si(001)-(2×1)surface was passivated by the chemisorption of tert-butanol. In order to explain the nature of the surface components we have also plotted the total and partial charge densities at the [`(K)]\bar{K} point of the surface Brillouin zone (SBZ).     

Diffusion of Au atoms and (5×2) phase formation on the Si(111) (7×7) surface

In this article we investigate the complex 1D mesoscopic model of adatom diffusion and the evolution of an ordered phase on the substrate surface. The analysis of the theoretical model is compared with the experimental results of the spreading of Au adatoms on Si(111)-(7×7) surface. The steady state solutions and their stability conditions are determined within the concept of the traveling-wave solution. It is shown that the formation of the ordered phase (5×2) and the difference in the diffusion of Au on (7×7) and on (5×2) structure results in a sharp edge of diffusion front which corresponds to the coverage of a saturated (5×2) phase. This edge moves linearly in time and α can be determined by experiment. The system of model equations enables the damped waves solution or temporary evolution of two steps.     

Nitric oxide adsorption on the Si(100)(2×1) surface — a vibrational study

High-resolution vibrational electron energy loss spectroscopy has been used to study the adsorbed state of NO on the Si(100)(2×1) surface. At 300 K, NO is adsorbed dissociatively on the Si(100) surface in the disordered structure, and the Si₃N and SiOSi species are formed. By heating at 1200–1300 K, the O adatoms are removed from the surface and the silicon nitride is formed; the (2×1) structure is recovered, which is interpreted to indicate that the nitride is formed mainly in the subsurface region.     

Self-assembled line growth of allyl alcohol on the H-terminated Si(100)-(2 × 1) surface

Using first-principles density-functional calculations, we investigate the growth mechanism of allyl alcohol (ALA) line on the H-terminated Si(100)-(2 × 1) surface. Unlike the allyl mercaptan (CH₂ = CH ? CH₂ ? SH) line, which was observed to grow across the Si dimer rows, we find that ALA (CH₂ = CH ? CH₂ ? OH) has the line growth along the Si dimer row. The self-assembled growth of ALA line occurs via the radical chain reaction mechanism, similar to the case of a typical alkene molecule, styrene. Our calculated energy profile along the reaction pathway shows that the different growth direction of ALA line compared with that of allyl mercaptan line is ascribed to the great instability of the oxygen radical intermediate, which prevents the line growth across the dimer rows.     

STM study of nucleation of Ag on Si(111)−(7 × 7) surface

Initial stages of Ag on Si(111)−(7 × 7) surface nucleation were studied at submonolayer coverage. Samples were prepared by thermal evaporation of Ag from tungsten wire under UHV conditions (p<2.5 × 10⁻⁸ Pa). Various deposition rates (0.002–0.1 ML s⁻¹) were used to prepare Ag island films with coverages (0.002–2) ML (1 ML ≈ 7.58 × 10¹⁴ atoms cm⁻²) at room temperature. We observed preferential growth on faulted half unit cells (F cells). At constant coverage both the island density and ratio of occupied F and U (unfaulted) cells are independent of the deposition rate, which is an evidence for dominant influence of substrate structure. The preference of nucleation in the F cells against U cells decreases with the coverage until the ratio is 1:1 for 1 ML Ag film. We have observed that presence of an Ag island in any type of the half unit cell (F or U) considerably reduces nucleation probability in neighbouring cells. This results in forming of structural patterns observed among randomly grown Ag-islands which is a new feature found for Ag/Si(111)−(7 × 7) system. Presented at the VIII-th Symposium on Surface Physics, Třešt’ Castle, Czech Republic, June 28 – July 2, 1999. This work was supported by the Grant Agency of Charles University — projects GAUK 34/97 and 147/99, by the Grant Agency of Czech Republic — project GAČR 202/97/1109 and by the Ministry of Education grant VS 97116.     

Deposition of ZnO thin films on (100) γ-LiAlO_2 substrate

The resurgence in the study of ZnO continues. The now ready availability of good-quality single crystals and films[1,2] and discovery of lasing action in the materials[3] have generated new life in an old material. A direct semi- conductor with a gap energy of 3.3 eV[4], ZnO is in the position of being able to offer a challenge to GaN in the blue laser market[5]. The advantages of ZnO are the high quality of the material and the large exciton bind- ing energy (60 meV). The large exciton bi…     

Combined theoretical and experimental determination of the atomic structure and adsorption site of Na on the Si(100)2 × 1 surface

The Na/Si(100)2 × 1 interface is studied by both ab initio local density functional total energy DMol molecular calculations using very large cluster models and photoemission EXAFS which provides the unique feature of probing both Na adsorbate and Si substrate environments. Theoretical and experimental bond lengths are found to be in very good agreement and enable a definite assignment of the adsorption site: Na is adsorbed on a single site, the cave, with no Na-Na distance consistent with any “double layer” models. The growth and existence of a second Na layer are shown to occur only in presence of very low level impurities.     

Formation of ultrathin magnetic cobalt films on the Si(111)7 × 7 surface

The phase composition, electronic structure, and magnetic properties of ultrathin cobalt films (no thicker than 20 ?) applied on a Si(111)7 × 7 surface at room temperature are studied by high-resolution photoelectron spectroscopy using synchrotron radiation and magnetic linear dichroism. It is shown that, as the cobalt thickness increases, first interface cobalt silicide and then an island (discontinuous) film of silicon-in-cobalt solid solution form on the silicon surface. A metal cobalt film starts growing after the deposition of a ∼7-?-thick Co layer. It is found that the ferromagnetic ordering of the system, which is characterized by surface magnetization, sets in after the deposition of a ∼6-?-Co layer at the stage of Co-Si solid solution formation.     

Electronic stabilization of the Si(111)5 × 2-Au surface: Pb and Si adatoms

Using scanning tunneling microscopy/spectroscopy (STM/STS), angle resolved photoemission spectroscopy (ARPES) and first-principles density functional theory (DFT), we study the structural and the electronic properties of the Si(111)5 × 2-Au surface decorated with Pb adatoms. The STM topography data reveal that Pb adatoms form a similar superstructure to that observed in the case of Si adatoms on a bare Si(111)5 × 2-Au surface. The DFT calculations show that preferential adsorption sites of Pb atoms are located near the double Au chain. Bias dependent STM topography and spectroscopy together with the DFT calculations allow us to distinguish Pb from Si adatoms. Both the Si and Pb adatoms modify the electronic properties in the same way, which confirms the electronic origin of the stabilization of the surface.