聚偏氟乙烯-稀释剂间介电常数差异对热致相分离法制膜微观结构的影响

采用1,4-丁内酯、邻苯二甲酸二甲酯、水杨酸甲酯、邻苯二甲酸二丁酯、三醋酸甘油酯和卡必醇醋酸酯作为稀释剂, 研究了在以热致相分离(TIPS)法制备聚偏氟乙烯(PVDF)微孔膜过程中, 聚偏氟乙烯-稀释剂间介电差异对PVDF膜微观结构的影响. 实验发现, PVDF-稀释剂间介电常数的差异与PVDF膜微观结构有一定关联. 当PVDF介电常数大于稀释剂的介电常数时, PVDF的分子间作用以引力为主导, PVDF分子易于聚集结晶, 形成松散球粒结构. 当PVDF介电常数与稀释剂的介电常数相近时, PVDF的分子间引力作用与斥力作用相均衡, 在淬冷条件下可形成近似双连续结构. 当PVDF介电常数小于稀释剂的介电常数时, PVDF分子间有一定的斥力效应, PVDF分子结晶困难.     

TIPS法制备聚偏氟乙烯平板微孔膜及其表征

以邻苯二甲酸二甲酯(DMP)为稀释剂,采用热致相分离法(TIPS)制备了聚偏氟乙烯(PVDF)平板微孔膜。利用差示扫描量热仪分析了不同PVDF/DMP体系的结晶性能;通过测试纯水通量、孔隙率、泡点、平均孔径、拉伸强度等对膜进行了表征。结果表明:DMP含量增大,结晶温度向低温方向移动,膜拉伸强度降低,当DMP的质量分数为0.70时膜拉伸强度有明显拐点;PVDF/DMP体系冷却发生固-液相分离;PVDF含量增大,膜水通量、孔隙率、最大孔径和平均孔径均减小。     

溶剂对相分离法制备聚偏氟乙烯微孔膜性质的影响

研究了用相转换法制备聚偏氟乙烯（PVDF）微孔膜时溶剂对成膜性质的影响.用浊点法测定了二甲基亚砜、N,N-二甲基甲酰胺、N,N-二甲基乙酰胺、N-甲基吡咯烷酮、磷酸三甲酯等五种溶剂配制的质量分数为wPVDF=0.12的铸膜液在30℃时的相分离点,显微镜拍照法测定了这些铸膜液与水接触时相分离前沿推进速率,泡点法测定了膜孔径,并测定了气体通量.结果表明,二甲基亚砜、磷酸三甲酯、N,N-二甲基乙酰胺是适于制作聚偏氟乙烯微孔膜的溶剂.     

热致相分离聚丙烯微孔膜

对聚丙烯－稀释剂体系热致相分离过程制备聚丙烯微孔膜的意义、原理、过程及研究现状进行了评述。     

热致相分离法高效制备压电聚偏氟乙烯膜

以环保溶剂乙酰柠檬酸三丁酯(ATBC)为稀释剂,绿色无毒的离子液体1-丁基-3-甲基咪唑六氟磷酸盐([BMIM][PF₆])为添加剂,采用热致相分离(TIPS)法制备聚偏氟乙烯(PVDF)微滤膜,通过扫描电子显微镜观察不同添加剂含量PVDF膜的微观形貌;通过超滤杯对PVDF膜的纯水通量进行了测试;使用拉力计对PVDF膜的机械性能进行了表征;通过红外光谱和X-射线衍射研究了添加剂对PVDF膜晶型结构的影响。结果表明：加入1.0%[BMIM][PF₆]时,PVDF的晶型变为β- 晶型。     

热致相分离法制备聚烯烃微孔膜研究进展

非极性及弱极性的结晶高聚物常温下无合适的良溶剂,所以无法使用传统的非溶剂致相分离法制取微孔膜,而近年来发展的热致相分离法解决了这一问题。研究发现聚乙烯、聚丙烯、乙烯．乙烯醇共聚物、乙烯．丙烯酸共聚物、聚(4-甲基-1-戊烯)等聚烯烃是可采用热致相分离法制备微孔膜的材料。本文综述了近年来在热致相分离法制备聚烯烃微孔膜方面的研究进展,重点介绍各种制膜材料(聚合物、稀释剂、萃取剂和助剂)与各种制膜工艺对制得的聚烯烃微孔膜孔径、膜通量和非对称结构等的影响。     

热致相分离法制备乙烯-三氟氯乙烯共聚物微孔膜

通过热致相分离法制备了乙烯-三氟氯乙烯共聚物(ECTFE)微孔膜, 考察了ECTFE与不同溶剂的相互作用参数对ECTFE/溶剂体系的液液相区的影响, 通过相容性分析及对ECTFE微孔膜断面结构的观察, 筛选出能与ECTFE发生明显液液相分离的溶剂--邻苯二甲酸二乙酯(DEP). 热力学相图证明, ECTFE/DEP体系具有较宽的液液相分离区, 偏晶点所对应的ECTFE质量分数高达55%. 考察了冷却条件对\{ECTFE/DEP体系膜断面结构的影响, 结果表明, 膜断面孔径随着淬冷温度的降低而减小, 在淬冷温度为458 K时膜断面孔径随粗化时间的增加而增大.     

热致相分离法制备聚苯硫醚微孔膜

采用热致相分离法,以己内酰胺为溶剂,制备得到了聚苯硫醚微孔膜并对薄膜性能表征.聚苯硫醚-己内酰胺体系制膜的优点之一是溶剂己内酰胺是水溶性的,可以采用纯水作为后处理的萃取剂.选择了合适的浓度,利用压制成型法制备聚苯硫醚平板膜;研究了体系冷却时的相行为,并考察了降温速率、聚合物浓度等因素对微孔形态与薄膜性能的影响.研究表明,聚苯硫醚-己内酰胺体系以固液分相为主,萃取后形成球晶状的微孔结构.降温速率对薄膜的微孔形态、孔径以及连通性有重要影响;当体系以较低降温速率冷却时,多孔形态为枝叶状,形成了更多的开孔结构并获得了更大的孔径,这是获得高通量微孔膜的主要原因.通过控制降温速率可以制备纯水通量大于100 L/m2h,孔径约4～5μm且连通性良好的聚苯硫醚微孔膜;研究了聚合物浓度的影响,薄膜的纯水通量随着聚合物浓度的增大而减小,并且当聚苯硫醚浓度>50 wt%时,由于大于临界浓度而失去渗透性.     

聚偏氟乙烯膜的改性研究进展

主要介绍了聚偏氟乙烯(PVDF)膜在近年来改性方法的最新研究进展,从辐照改性、等离子体改性、共混改性和化学改性等几方面进行了详细介绍,简要介绍了PVDF膜作为离子交换膜的一些最新应用.     

Polysulfone Membranes via Thermally Induced Phase Separation

Polysulfone (PSF) membranes have gained great attention in the fields of ultrafiltration,microfiltration,and thin film composite membranes for nanofiltration or reverse osmosis.For the first time,it is proposed to fabricate PSF membranes via thermally induced phase separation (TIPS) process using diphenyl sulfone (DPSO2) and polyethylene glycol (PEG) as mixed diluent.DPSO2 is chosen as a crystallizable diluent,while PEG is considered in terms of molecular weight (Mw) and dosage.We systematically investigate the interactions between PSF,DPSO2 and PEG based on the simulation calculations and solubility parameter theory.It is inferred that DPSO2 has an excellent compatibility with PSF,and the addition of PEG results in the ternary system thermodynamically less stable and then facilitates its liquid-liquid (L-L) phase separation.SEM images indicate that cellular-like pores are obvious throughout the membrane when the PEG content in the mixed diluent is 25 wt％-35 wt％.We can facilely manipulate the pore size,water flux and mechanical properties of PSF membranes with the dosage of PEG-200,the Mw of PEG or the cooling rate.The successful application of TIPS can provide a new approach for structure manipulation and performance enhancement of PSF membranes.     

Construction of Renewable Superhydrophobic Surfaces via Thermally Induced Phase Separation and Mechanical Peeling

We report a simple preparation method of a renewable superhydrophobic surface by ther-mally induced phase separation (TIPS) and mechanical peeling. Porous polyvinylidene fluo-ride (PVDF) membranes with hierarchical structures were prepared by a TIPS process under different cooling conditions, which were confirmed by scanning electron microscopy and mer-cury intrusion porosimetry. After peeling off the top layer, rough structures with hundreds of nanometers to several microns were obtained. A digital microscopy determines that the surface roughness of peeled PVDF membranes is much higher than that of the original PVDF membrane, which is important to obtain the superhydrophobicity. Water contact angle and sliding angle measurements demonstrate that the peeled membrane surfaces display super-hydrophobicity with a high contact angle (152°) and a low sliding angle (7.2°). Moreover, the superhydrophobicity can be easily recovered for many times by a simple mechanical peel-ing, identical to the original superhydrophobicity. This simple preparation method is low cost, and suitable for large-scale industrialization, which may offer more opportunities for practical applications.     

热致相分离法制备聚合物微孔材料

热致相分离是一种制备聚合物微孔材料的有效方法。本文介绍了聚合物初始浓度、聚合物分子量、稀释剂、冷却速率、萃取剂、聚合物密度等因素对热致相分离法制备聚合物微孔材料的影响,并对热致相分离法制备新型微孔材料的最新研究进展进行了综述。     

Effect of Diluent Mixture on Porous Structure of Polyphenylene Sulfide via Thermally Induced Phase Separation

Polyphenylene sulfide (PPS) microporous membranes were prepared via the thermally induced phase separation process using diluent mixtures of diphenyl ether (DPE) and diphenyl ketone (DPK). The effects of DPE ratio to DPK in the diluent mixture on the microstructure were investigated. The results showed that the pore morphology of the membranes prepared from the diluent mixture was different from those of fabricated from pure diluents. Moreover, the pore structures of the membranes were changed along with the variation of the diluent composition.     

热致相分离法偏二氯乙烯-氯乙烯共聚物多孔膜的制备及性能

以偏二氯乙烯-氯乙烯共聚物[P(VDC-co-VC)]为成膜聚合物, 邻苯二甲酸二甲酯(DMP)为稀释剂, 采用热致相分离(TIPS)法制备了具有多孔结构的P(VDC-co-VC)膜. 通过聚合物-稀释剂二元体系相图、 场发射扫描电镜(FESEM)、 差示扫描量热仪(DSC)、 X射线衍射(XRD)、 原子力显微镜(AFM)、 纯水通量、 接触角、 孔径及其分布、 截留率及力学性能等研究了聚合物含量对P(VDC-co-VC)多孔膜结构和性能的影响. 结果表明, P(VDC-co-VC)-DMP二元体系成膜过程以液-液(L-L)分相为主, 随着聚合物含量增加, 膜的横截面由类花瓣状结构向胞腔状结构转变, 膜的孔连通性降低, 结构变得较为致密, 同时膜上表面孔隙率降低, 粗糙度增大. L-L分相时间和聚合物含量的变化, 导致膜结晶度先降低后增大. 聚合物含量的增加使膜上表面接触角、 断裂强度及蛋白截留率增加, 但膜的平均孔径、 孔隙率及纯水通量先增加后减小. 当聚合物质量分数为30%时, 所得膜通透性较优, 断裂强度可达7.5 MPa.