Optically pumped submillimeter laser lines from CD2Cl2 using a large tunability CW CO2 laser

Twenty-five new laser lines have been obtained in the wavelength region from 155 to 830 μm by optically pumping the CD₂Cl₂ (deuterated dichloromethane) molecule with a CW CO₂ laser having a tunability range of 300 MHz. The wavelength, polarization relative to that of CO₂ pumping radiation, and offset relative to the CO₂ center frequency were determined for all of the new lines and some other already known laser emissions. For all of them we give also the relative intensity and the optimum pressure of operation. Permanent address: Depto de Física e Química da FEIS — UNESP 15.378-000 Ilha Solteira-SP, Brazil     

Far infrared laser frequencies of CH3OD and N2H4

The frequencies of 26 laser lines with wavelengths between 57 and 534 m have been measured in the optically pumped laser gases CH₃OD and N₂H₄. A pair of stabilized cw 12_{CO 2} lasers was used as a frequency standard for the heterodyne frequency measurements. Seven of the 26 lines are new.     

Slab CO2 lasers excited by switching power

In this paper we present a new discharge technique to excite slab CO₂ lasers. A uniform stable glow discharge has been obtained in a volume of 3 × 30 × 446 mm³. Output power is 10 W, and a gain of 0.26% cm⁻¹ has been obtained.     

A compact, highly stable CW CO2 laser without brewster windows

We describe an open resonator, quasi sealed-off; 70cm cavity length CO₂ laser with very high stability of power and frequency, which lases on 96 lines from 9R42 (2W) to 10P52 (5W) with a power of >11W on 9R20, 9P20, 10R20 and 10P20, plus on 18 hotband lines with ≈2W. This laser was used successfully to pump an FIR ring laser [1] enabling an FIR power stability of ΔP/P ≈ 10⁻⁴ by use of a simple PI control loop, thus demonstrating its superb frequency stability.     

Frequency measurements of CF2CHF and SO2 laser lines and a new far infrared laser line of HDCO

The emission frequencies of several optically pumped far infrared laser lines of CH₂CHF, SO₂ and HDCO molecules have been measured by mixing them with a harmonic of a millimeter-wave synthesizer operating in the range 78–118 GHz. A new line of HDCO at 1886 GHz has been found.     

Optical pumping by CO2 and N2O lasers: New cw FIR emissions in vinyl cyanide

A systematical study of optical pumping by CO₂ and N₂O lasers using a FIR metallic waveguide has been undertaken in vinyl cyanide. 97 new FIR laser lines are reported in the wavelength range 400 m–1,5 mm.Unité associée au CNRS (UA 836).     

Pulse behaviour of a compact RF discharged CO2 slab laser

We present the measurements made on a medium power, 35 cm long, radio-frequency discharge CO₂ slab laser operated in a pulsed regime obtained by switching the RF discharge. In this way, pulses with peak power up to 480 W at pulse repetition frequencies in the range 1 to 10 kHz have been obtained. Pulse energy and average extracted power have been experimentally characterized with respect to the pulse repetition frequency and to the pulse duration, and the pulse shape and characteristic times have been measured. We also investigated the propagation properties of the beam emerging from our laser.     

Thermal processes taking place in the bone during CO2 laser irradiation

The present study examines the drilling and heating of a bone due to pulsed CO₂ laser irradiation. To obtain temperature profiles inside and at the surface of the bone, electron-kinetic and Fourier theories are used. The study is extended to include an experimental investigation into the measurement of the penetration speed. This is achieved using a fibre-optic system. In order to reduce the degree of burning around the hole side, helium was used as the assisting gas during drilling. It is found that the penetration speeds predicted from the theory are in good agreement with the experimentally obtained values.     

CO2 laser cutting of slate

Slate is a natural stone which has the characteristic that shows a well-developed defoliation plane, allowing to easily split it in plates parallel to that plane which are particularly used as tiles for roof building. At present, the manufacturing of slate is mostly manual, being noisy, powdery and unsafe for the worker. Thus, there is a need to introduce new processing methods in order to improve both the working conditions and the quality of the products made of slate.Following the previous work focused on the drilling and cutting of slate tiles using a Nd : YAG laser, we present in this paper the results of the work carried out to explore the possibilities to cut slate plates by using a CO₂ laser. A 1.5 kW CO₂ laser was used to perform different experiments in which, the influence of some processing parameters (average power, assist gas pressure) on the geometry and quality of the cut was studied. The results obtained show that the CO₂ laser is a feasible tool for a successful cutting of slate.     

Mathematical modeling of hybrid CO2 laser

A Teller–Landau six-temperature model describing the dynamic emission of single-mode TEA CO₂ laser has been adapted. This model has been also used to describe the mechanism of obtaining relatively high-power output pulses from hybrid TE-TEA or CW-TEA CO₂ laser consisting of high- and low-pressure sections. The suggested mathematical model allows to investigate the mechanism which limits the TEA oscillation to single longitudinal mode (SLM) due to the narrow gain bandwidth of low-pressure section, and also to study the effect of the laser input parameters on the smooth output laser pulse parameters. In addition, numerical solutions of non-linear rate equation system of the suggested model are quantitatively discussed. The solutions describe the radiation field intensity, the population inversion, and the energy transfer processes. The calculated values of maximum peak power, total energy in pulse, pulse width, etc. are in a very good agreement with the observed experimental values.     

CO2 laser assisted removal of UO2 and ThO2 particulates from metal surface

Pulsed laser assisted removal of uranium dioxide and thorium dioxide particulates from stainless steel surface have been studied using a TEA CO₂ laser. Decontamination efficiency is measured as a function of laser fluence and number of pulses. Threshold fluence for the removal of UO₂ particulates has been found to be lower than that required for the removal ThO₂ particulates. Usage of a ZnSe substrate, that is transparent to the laser wavelength used here, enabled us to decouple the cleaning effect arising out of absorption in the particulates from that in the substrate and has contributed towards understanding the mechanism responsible for cleaning. The experimental observations are also corroborated by simple theoretical calculations.     

Tunable electrooptically Q-switched RF excited CO2 waveguide laser with two channels

A tunable electrooptically Q-switched RF excited waveguide CO₂ laser with two channels is presented. Q-switched pulses have been obtained from one of the channels. The peak power is 300 W and the pulse width is 140 ns. CW laser output has been obtained from the other channel, which can been tuned by a PZT. The short-term heterodyne stability can be up to 10⁻⁹.     

Short single-mode CO2 laser pulse generation by pulsed Q-switching

A simple method for the generation of short, single-mode CO₂ laser pulses produced by applying two voltage gates (of amplitude 3U_λ/4 and U_λ/4) to an electro-optic Q-switch placed in a three-mirror cavity is proposed. Single, single-mode, well-synchronizable pulses of 3 ns duration and of 3 mJ energy have been experimentally achieved from a TEA CO₂ laser with an intracavity Pockels cell with 3 ns switching time. Using a numerical simulation it is shown that with shorter switching time (≈1 ns) the method enables one to obtain, from such a laser, a single, megawatt pulse of 1 ns duration.     

AC-chopper application for CW CO2 laser

A microprocessor-based algorithm was developed to control the power supply to a CO₂ laser using an AC-chopper method. This system was connected directly to a CO₂ laser tube without the need for a dc-dc converter or the storage capacitance of a multilevel circuit. The typical CO₂ laser power supply system had a full-bridge series resonant inverter or voltage multiplier. AC-to-AC converter schemes using zero voltage switching (ZVS) can be used efficiently and economically for low and medium power applications.This paper reports the performance characteristics of a symmetrical AC-chopper technology that can maintain the quality of the ac output of a CO₂ laser tube, regardless of the amount of switching loss. The laser was operated to an output power, maximum system efficiency total gas mixture of 37.2 W, 92%, and CO₂:N₂:He=1:9:15, respectively. The laser system, AC-chopper power supply and its operation were examined.     

Diffusion of excited state molecules in FIR- and CO2-lasers

Both standing waves in laser oscillators and spatially inhomogenous cross sections of laser beam and pumprate cause a non-uniform distribution of excited state molecules in longitudinal and transversal direction, respectively. This spatial hole burning however is smoothed by diffusion of the excited molecules. The effect of diffusion is investigated theoretically for an optically pumped far infrared laser as well as the corresponding CO₂ pump laser. It is found, that the remaining spatial hole burning in the direction of wave propagation is negligible within CO₂ lasers but not within FIR lasers. Concerning the transversal direction it can be shown that in the FIR laser diffusion takes no effect, whereas the transversal distribution of the excited molecules in the CO₂ laser is significantly influenced by diffusion.FIR ring lasers avoid longitudinal spatial hole burning, which leads to the common assumption that they use the active medium more efficient than conventional standing wave lasers, hence delivering higher output powers. This expected advantage is levelled out to a great extent by diffusion.     

In-process high power CO2 laser beam position sensing

The case for in-process sensing is one of the strengths of laser materials processing, both in the variety of signals obtainable from the process and the range of techniques for beam guidance. It is known that beam/nozzle alignment is of importance for high quality laser cutting. Thus, an in-process beam position sensing system was devised in this study as one of the potential tools for automation of the cutting process. Further, if the beam could be stabilized at a given location automatically this would be equivalent to relocating the laser beam. Laser beam position sensing is the first step towards this goal. The aim of this study is to create a beam position sensing system. This work presents a new approach using a rotating slit, a focusing lens and a photodetector. An automatic alignment procedure is also investigated.     

High-power multibeam CO2 laser for industrial applications

Multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes, all sharing a common plane parallel resonator. This paper describes construction and operation of a CW multibeam CO₂ laser consisting 20 discharge tubes and cooled length of 1500 mm, delivering 1 kW power. A high-frequency pulser is used for producing preionization in all discharge sections for initiating the main DC discharge simultaneously in all discharge tubes. Plane parallel resonator consists of a plane ZnSe mirror of 90 mm diameter having 60% reflectivity and a gold-coated copper mirror of same diameter. This laser operates in waveguide regime and laser power is not critically sensitive to mirror misalignment.     

A compact TEA CO2 laser for field-based spectrochemical analysis of geological samples

A compact capacitor-transfer TEA CO₂ laser of 180 mJ output energy and 50 ns pulse duration in half width was designed and constructed for field use. This laser is suitable for laser microprobe spectrochemical analysis on geological and mining samples. Experiments show that the use of helium as a surrounding gas suppresses the continuous emission spectrum of the plasma, thus increasing the S/N ratio. Using glass as standard samples, the minimum detectable concentrations are estimated with Zn neutral line and F ionic line to be 60 ppm and 500 ppm, respectively.     

Temperature distribution along oversized hollow-core waveguides for CO2 laser radiation

Temperature distributions along various hollow waveguides are fully analysed experimentally when the waveguides are excited by CO₂ laser light. It is shown that the temperature decreases in an oscillatory manner along the waveguides due to the interference effect of guided modes. The distributors are well explained by a theory developed previously.     

Phase-locking of a multi-channel radial array CO2 laser

A theoretical analysis of phase-locking in a multi-channel radial array CO₂ laser is presented. The concepts are based on the theories of injection phase-locking and matrix optics. The mutual optical coupling occurring within the central region is demonstrated by theoretical deduction. Interrelated graphs of the coupling coefficient and the distance between the coupling position and the cavity mirror are calculated by numerical simulation. The results of the analysis are in accord with experimental results.