噻吩醛缩乙二胺席夫碱及其配合物的合成与光催化性能

基于TiO₂光催化性能的染料敏化改性,采用2-噻吩甲醛缩合乙二胺合成了席夫碱配体L,并与金属配合得到了金属配合物[ZnLCl₂](1),[NiL'(NO₃)₂](2)(L'为单噻吩醛缩乙二胺),对配体L、配合物1 和2进行了X射线单晶衍射结构分析。 用合成的配体和配合物修饰TiO₂得到相应的复合光催化剂L-TiO₂、1-TiO₂和2-TiO₂,并进行了红外光谱、紫外-可见漫反射光谱、粉末X射线衍射图谱等表征,研究了这3种光催化剂降解水中有机污染物4-硝基酚(4-NP)和罗丹明B(RhB)的催化活性。 结果表明,1-TiO₂、2-TiO₂可以有效的降解4-NP和RhB,降解率可达90%以上。     

γ-Fe2O3/Ag/TiO2的制备与抗菌性能

采用两步法合成了γ-Fe₂O₃/Ag/TiO₂复合光催化剂, 以大肠埃希氏菌(E. coli)为目标菌, 对数去除率为评价指标评价了催化剂的抗菌性能, 优化了催化剂的最佳制备参数. 通过X射线衍射、 扫描电子显微镜、 X射线光电子能谱和紫外-可见漫反射光谱等手段对催化剂进行了表征. 结果表明, 当Ti/Ag摩尔比为1:0.05, 煅烧时间为3 h, 煅烧温度为350 ℃时, γ-Fe₂O₃/Ag/TiO₂表现出最佳抗菌活性. 复合催化剂具有介孔结构, 比表面积为89.1 m²/g; 光吸收边界达690 nm, 有良好的可见光响应能力; 磁性较强, 在水处理应用中可有效分离和重复使用. 反应条件不受光源限制, 在有/无光照下均具有良好的抗菌活性, 且太阳光辐照下对E. coli的对数去除率可达6.28.     

TiO2-yNx纳米光催化剂的制备及其可见光响应机理

利用溶胶-凝胶技术,以尿素为氮源,采用原位掺杂方式制备了TiO2-yNx纳米粉体;以亚甲基蓝(MB)溶液在可见光下的光催化降解评价其可见光催化活性;考察了体系初始pH值、N的掺杂量和焙烧温度对样品可见光催化活性的影响。 结合XRD、XPS、ESR和DRS测试技术,研究了N掺杂纳米TiO2的可见光响应机理。 研究结果表明,TiO2-yNx纳米粉体的优化制备工艺条件为：体系初始pH=0.52,掺杂比n(N)∶n(Ti)=1∶6,焙烧温度为440 ℃。 此条件下制备的样品N含量为0.77%,为单一的锐钛矿相,平均粒径为19.0 nm,具有良好的可见光催化活性。 N掺杂导致TiO2纳米粉体的表面羟基含量增加,形成了大量束缚单电子的氧空位;N取代晶格O形成了N-Ti-O和O-N-Ti键合结构。 N掺杂导致TiO2纳米粒子的吸收带边红移,对可见光的吸收能力明显增强,这表明N掺杂改变TiO2电子结构,使带隙窄化,降低光响应阈值。 N掺杂TiO2纳米粒子的可见光响应归因于N取代掺杂形成的掺杂能级与氧空位形成的缺陷能级共同作用所致。     

β-PbO2/Sb-SnO2/Ti电极的苯酚电催化性能研究

采用刷涂热解和电镀制得了β-PbO₂/Sb-SnO₂/Ti电极. 采用X射线衍射（X-ray Diffraction,XRD）和扫描电镜（Scanning Electron Microscope,SEM）进行分析与观察,Sb-SnO₂中间层抑制PbF₂的生成,NaF促进二氧化铅晶粒的成型与分散,消除了β-PbO₂聚团. 据谢乐公式（Scherrer）计算晶粒尺寸为25.2 nm,电极表面结晶度高达100%. 极化测试显示,β-PbO₂/Sb-SnO₂/Ti电极扩散段电位区、析氧电位和Tafel斜率分别为1.85 ~ 2.15 V、2.08 V和0.84,优于β-PbO₂/Ti电极的1.40 ~ 1.80 V、1.75 V和0.36. 使用β-PbO₂/Sb-SnO₂/Ti、β-PbO₂/Ti电极在9 mA·cm^-2电流密度对苯酚模拟废水处理240 min,前者COD（Chemical Oxygen Demand）去除率、电流效率（Instant Current Efficiency）高达90.1%和63.28%,优于后者66.9%和44.96%. 寿命测试表明,β-PbO₂/Sb-SnO₂/Ti电极与β-PbO₂/Ti电极相比延长10倍,工业寿命可达8.6a,有较高的工程应用价值.     

二氧化锰/石墨烯纸电极的制备及其电化学性能

通过电化学法使溶液中的Mn²⁺电解氧化为MnO₂,沉积复合在石墨烯片膜上,形成由MnO₂/石墨烯复合材料构成的纸电极。 采用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)、循环伏安(CV)和恒流放电等技术手段对纸电极材料的结构、形貌以及电化学性能进行了研究。 结果表明,MnO₂球形颗粒均匀地沉积在石墨烯片膜上,形成了厚度45 μm的纸电极,经过380 ℃煅烧后,纸电极中的MnO₂晶型由γ-MnO₂转化为β/γ-MnO₂混合晶型,是良好的柔性Li/MnO₂电池的电极材料。 MnO₂/石墨烯纸电极在室温下0.1C放电容量达269 mA·h/g,而且电化学阻抗低、柔韧性好。     

Synthesis and Visible-light Photocatalytic Performance of C-doped Nb2O5 with High Surface Area

C-doped Nb₂O₅ with abundant mesopores has been successfully synthesized through a facile solvothermal synthetic strategy followed by calcination treatment. The resulting C-doped Nb₂O₅ displayed the highest BET surface area(345 m²/g) and large mesopore size(ca. 4.2 nm), capable of offering more accessible active sites as well as faster mass transfer for catalysis. Besides, the doping of C(2.21%, molar fraction) at the O sites in Nb₂O₅ lattice greatly enhanced visible-light response by lowering the band gap, thereby making the material a photocatalyst under visible-light irradiation. Typically, the C-doped Nb₂O₅ exhibited a high H₂ evolution rate of ca. 39.10 μmol·g^-1·h^-1 and also degraded RhB dye completely after 30 min of visible light exposure, which turned out to be much better than Degussa P25 and pure Nb₂O₅ catalysts.     

氮掺杂还原氧化石墨烯与吡啶共聚g-C3N4复合光催化剂及其增强的产氢活性

Here, we fabricated a pyridine-copolymerized g-C₃N₄ by a novel and cost-effective approach based on Schiff-base chemistry. Thus produced g-C₃N₄ showed significantly enhanced and stable visible-light photocatalytic H₂ evolution performance compared to pristine g-C₃N₄ obtained from urea. Subsequently, we constructed a composite of pyridine-modified g-C₃N₄ and N-doped reduced graphene oxide (N-rGO) by facile one-pot calcination to elevate the photocatalytic efficiency further. The peak H₂ production rate achieved using this composite was 304 μmol·h^-1, about 11.7 and 3.1 times as those obtained using pure g-C₃N₄ and pyridine-modified g-C₃N₄, respectively. In addition to enhanced visible light absorbance and enlarged surface area, the promoted separation, transfer, and surface reactivity of photogenerated charge carriers by the pyridine ring as intramolecular electron acceptor and N-rGO as "electron-transfer activation region" are considered responsible for the remarkably enhanced photocatalytic activity.     

Visible-light-sensitive N-doped TiO<Subscript>2</Subscript> photocatalysts prepared by a mechanochemical method: effect of a nitrogen source

Nitrogen-doped titanium dioxide (N-doped TiO₂) photocatalysts were prepared by a mechanochemical method by using a high-speed ball milling of P25 TiO₂ with nitrogen sources such as ammonia solution, hexamine, and urea. Visible-light absorption was determined from the onset of diffused reflectance spectrum. The photocatalytic activity of the N-doped TiO₂ was evaluated through the removal of methylene blue (MB) under visible-light irradiation. The effects of nitrogen precursors used during the mechanochemical synthesis on the catalysts’ properties, such as the effective particle size, surface area, and photocatalytic activity, were extensively investigated.     

Dye-sensitized solar cells made from BaTiO3-coated TiO2 nanoporous electrodes

We reported on the preparation of a thin BaTiO₃-coated layer (2.27 nm) on the surface of TiO₂ and its further application in the dye-sensitized solar cells (DSCs). The as-prepared BaTiO₃–TiO₂ films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscope (TEM). The performances of the DSCs with and without BaTiO₃ coating were analyzed by cyclic voltammograms (CVs), electrochemical impedance spectroscopy (EIS), and current–voltage measurements. It was found that the BaTiO₃–TiO₂ films with about 12 μm thickness increased the dye adsorption, resulting in increased J_sc. In the meantime, the BaTiO₃ modification on the TiO₂ surface is beneficial to the formation of an energy barrier against the electron transfer from TiO₂ to I₃⁻, providing the increase of V_oc due to the increased electron density in the TiO₂ that is caused by the increased electron lifetime.     

LaNi4M(Ni,Cu,Fe)-H2体系的量热研究

本文用量热法测定了氢在LaNi₅,LaNi₄Cu,LaNi₄Fe中溶解的相对偏摩尔焓△H_Hα→β和偏摩尔自由能△G_Hα→β,并计算了偏摩尔熵△S_Hα→β。用X光衍射分析计算了LaNi₅,LaNi₄Cu,LaNi₄Fe的晶胞体积V,发现了△H_Hα→β和△G_Hα→β)与V存在线性关系。     

不同晶相结构二氧化锰催化完全氧化乙醇

采用水热合成法制备了α-MnO₂、β-MnO₂、γ-MnO₂和δ-MnO₂催化剂, 运用N₂吸脱附实验、X射线衍射(XRD)、X射线光电子能谱(XPS)和H₂程序升温还原(H₂-TPR)等方法对催化剂进行了表征, 并将催化剂用于催化完全氧化乙醇反应中, 考察了不同晶型MnO₂催化剂催化氧化乙醇活性的差异, 探讨了催化剂晶型结构与催化氧化活性的关联. 结果表明, 不同晶型的MnO₂催化剂催化氧化乙醇活性差异显著, 活性顺序为α-MnO₂>δ-MnO₂>γ-MnO₂>β-MnO₂. 系列表征结果显示, 晶体结晶度和比表面积不是影响不同晶型MnO₂催化剂活性的主要原因, α-MnO₂催化剂具有的较高晶格氧浓度和较高的可还原性是其具有良好催化氧化乙醇活性的关键因素.     

四种晶型MnO2超级电容器电极材料的电化学性能研究

用尽量简便的方法制备出δ、α、β及γ型4种MnO₂粉末. 通过X射线衍射（XRD）、场发射扫描电镜（FSEM）、热重分析（TGA）与比表面积测试（BET）等方法对样品粉末性质进行分析,并对4种不同粉末制成的电极进行循环伏安、恒流充放电及稳定性测试. 结果表明,4种MnO₂都具有良好的电容特性,其中α-MnO₂具有最高的比表面积与孔隙率,故其电极比容量最高,但其大电流放电时的倍率特性较差. 其余3种MnO₂比表面积相当,而β-MnO₂虽然比容量较低,但其简单的孔隙结构使其拥有最好的倍率特性与稳定性.     

β-Mo_2C和Ni_3Mo_3N/β-Mo_2C的制备及其甲烷化反应性能研究

通过焙烧钼酸铵和六次甲基四胺(HMT)生成的络合物,制备β-Mo_2C。在此基础上加入Ni助剂制备了Ni_3Mo_3N/β-Mo_2C双金属碳化物催化剂。采用XRD、SEM、HRTEM、低温氮吸附、元素分析等方法对催化剂进行了表征,考察了其合成气甲烷化反应性能。结果表明,β-Mo_2C有较高的CO转化率,但CO转化率和CH_4选择性分别从第10h的75.93%和36.79%降低到了第100h的67.41%和33.54%。因此,β-Mo_2C活性不够稳定且CH_4选择性较低。而Ni助剂的加入显著提高了催化剂的甲烷化活性及稳定性,使CO转化率和CH_4选择性分别从第10h的83.15%和46.64%升高到了第100h的92.51%和57.23%。这是因为Ni助剂的加入有助于生成Ni_3Mo_3N,新生成的Ni_3Mo_3N有利于甲烷化反应。     

Promoting Effects of Iron on CO Oxidation over Au/TiO2 Supported Au Nanoparticles

Fe-doped TiO₂ supported gold nanoparticles as high-performance CO oxidation catalysts were prepared. XRD data revealed that TiO₂ support was in an anatase phase. After calcination at 300℃, the sample showed nanotube structure, and the size of gold nanoparticles was 3.1 nm. When calcined at 500℃, most nanotubes broke, and gold nanoparticles grew up to 5.9 nm. XPS spectrum indicated the presence of Fe in the +3 oxidation state. Au/Fe-TiO₂(Au:1.44%, Fe:1.35%) calcined at 300℃ possessed the best catalytic activity, and it could completely convert CO at 25℃. The temperature of 100% CO conversion(T_100%) of Fe-free catalyst was 40℃. After the catalysts were stored at room temperature for 7 d, T_100% of Au/Fe-TiO₂ increased from 25℃ to 30℃, while T_100% of Fe-free catalyst increased from 40℃ to 80℃. The catalytic activity and storage stability of Au/TiO₂ could be improved by Fe-doping. The increase of specific surface area, generation of oxygen vacancies and new adsorption sites, depression of the growth of gold nanoparticles, and strong metal-support interaction were responsible for the promoting effect of iron on the catalytic performance of Au/TiO₂ for CO oxidation.     

Studies on the Halogen Substituted β-Amino Acids and Their Cu(Ⅱ) Coordination Complexes in Crystallography

Halogen substituted β-amino acids, D,L-3-amino-3-(4-fluoro)phenylpropionic acid(D,L-HL1, 1) and D,L-3-amino-3-(4-bromo)phenylpropionic acid(D,L-HL2, 2), as well as their Cu(Ⅱ) coordination complexes[Cu(L1)₂(CH₃OH)₂]·2CH₃OH(3) and[Cu(L2)₂(CH₃OH)₂]·2CH₃OH(4) were investigated and their single crystal structures were discussed in details. Supramolecular helical chains were found in β-amino acids 1 and 2 while there was no helix in their coordination complexes 3 and 4. The formation of supramolecular helixes could be due to the hydrogen bonds between terminal-NH³⁺ and adjacent-COO^- in β-amino acids 1 and 2. While, this kind of hydrogen bonds could not be observed in their Cu(Ⅱ) coordination complexes 3 and 4, in which central-symmetrical dimers could be formed via coplanar coordinated bonds(N-Cu-O) between-NH₂ and-COO^-.     

Co-Ce共掺杂对TiO_2催化剂室温可见光催化脱硝性能的影响

将钛酸丁酯作为Ti源,硝酸铈作为Ce源,硝酸钴作为Co源,采用溶胶-凝胶水热法制备出Ce-TiO_2和Ce-Co-TiO_2催化剂。对所制备的改性TiO_2催化剂进行BET、XRD、SEM、UV-vis、XPS、NH_3-TPD等表征分析测试,并以NO为研究对象对不同改性TiO_2催化剂进行了可见光催化实验,探究改性TiO_2催化剂脱除NO的效率。结果表明,以硝酸铈为Ce源(掺杂物质的量比1%),硝酸钴为Co源(掺杂物质的量比5%),在水热反应温度为160℃的条件下反应24 h后在200℃下煅烧得到的Ce(1%)-Co(5%)-TiO_2催化剂性能最好。其对浓度为762μg/m~3的NO可见光催化效率高达92.69%,在浓度提高至1148μg/m~3时在室温下的可见光催化效率仍可达85.94%,与纯TiO_2相比效率提高了近50%。而且Ce (1%)-Co (5%)-TiO_2催化剂的抗硫性能与连续使用次数都比商用催化剂(掺杂有V_2O_5的商用TiO_2)好。     

Carbon-containing nano-titania prepared by chemical vapor deposition and its visible-light-responsive photocatalytic activity

Ultraviolet and visible-light-responsive titania was synthesized and employed in the NO_x photomineralization. A thermal decomposition reaction of titanium isopropoxide was carried out with a metal-organic chemical vapor deposition (MOCVD), enabling continuous production of TiO₂ nanoparticles. Carbon-containing titanium dioxide with the anatase phase prepared at 500 °C under nitrogen atmosphere exhibited high photocatalytic activity for NO oxidation under visible-light illumination. Experimental results indicate that up to 48% removal of NO_x can be achieved in a continuous flow type of reaction system under visible-light illumination (green LED). The chamber temperature in this MOCVD process plays an important role in lattice structure formation, and also affected TiO₂ carbon content. The carbonaceous species on the TiO₂ surface, shown by X-ray diffractometry (XRD), and Raman, UV–vis, and X-ray photoelectron spectroscopies (XPS), is important to the visible-light absorption and visible-light-catalytic mineralization of NO_x.     

Synthesis and Characterization of SnO2-TiO2 Nanocomposite with Rutile-phase via Hydrothermal Method at Low Temperature

With Ti(SO₄)₂, SnCl₄·5H₂O and urea as raw materials, SnO₂-TiO₂ nanocomposites were synthesized via low temperature hydrothermal method at 80―100 ℃ in aqueous solutions. The morphologies of the products were altered systematically by varying the Ti/Sn molar ratio of the reactants, and rutile-phase particles were obtained with an average diameter of about 52.2 nm at a molar ratio of Ti/Sn=7.5. The surface composition of the composite was revealed by X-ray photoelectron spectroscopy(XPS) and X-ray diffraction(XRD) to be solely TiO₂ with a rutile structure. This new composite material exhibits a high ultraviolet absorption capacity, and its photocatalytic activity for phenol oxidation is much lower than that of the commercial titania nanoparticles(P25).     

N-Doped Carbon Nanofibers Encapsulating CoO@Co9S8 Nanoparticles: Preparation from S-Rich Co32 Coordination Cluster Precursors by Electrospinning and Application for Superior Li-ion Storage

Thiacalixarene-supported Co₃₂nanoclusters encapsulated in polyacrylonitrile nanofibers(Co₃₂@PAN-NFs) by electrospinning have been utilized as precursors to fabricate N-doped CoO@Co₉S₈ carbon nanofibers(CoO@Co₉S₈@CNFs) for superior Li-ion storage. The S-rich Co₃₂ clusters capped by organic sheets afforded the well dispersed cobalt oxide/sulfide nanoparticles embedded in carbon nanofiber composites by direct calcination. The N-doped CoO@Co₉S₈@CNFs nanocomposites have been utilized as anode materials for lithium ion battery with the reversible capabilities being of 1051.8, 967.6, 894.7, 782.7, 669.5 and 525.4 mA·h/g at 0.1, 0.2, 0.5, 1, 2 and 3 A/g, respectively. The CoO@Co₉S₈@CNFs also showed a relatively high stable capacity of 551.7 mA·h/g at the current density of 1 A/g after 200 cycles of rate experiments. The as-obtained N-doped CoO@Co₉S₈@CNFs nanocomposites exhibited superior reversible capacity, rate performance, Coulomb efficiency(74.5% vs. 63.9%) and cyclic stability comparing with the CoO@Co₉S₈@C derived from simple annealing of Co₃₂ templates.     

Tunable Synthesis of Core-shell α-Fe2O3/TiO2 Composite Nanoparticles and Their Visible-light Photocatalytic Activity

Uniform α-Fe₂O₃/amorphous TiO₂ core-shell nanocomposites were prepared via a hydrolysis method and α-Fe₂O₃/anatase TiO₂ core-shell nanocomposites were obtained via a post-calcination process. The structure and morphology of the products were characterized by powder X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy and scanning electron microscopy. Amorphous TiO₂ nanoparticles with diameters of ten to several tens nanometer were formed on the surface of α-Fe₂O₃ nanoparticles and the coverage density of the secondary TiO₂ nanoparticles in the composite can be controlled by varying the concentration of Ti(BuO)₄ in the ethanol solution. The visible-light photocatalytic properties of different products towards Rhodamine B(RhB) were investigated. The results show that the α-Fe₂O₃/amorphous TiO₂ exhibits a good photocatalytic property owing to the extension of the light response range to visible light and the efficient separation of photogenerated electrons and holes between α-Fe₂O₃ and amorphous TiO₂.