辛基三甲基溴化铵与辛基硫酸钠混合水溶液的相行为

对辛基三甲基溴化铵(OTAB)与辛基硫酸钠(SOS)正、负离子混合表面活性剂水溶液的相行为进行了研究.在高浓度的溶液中,混合表面活性剂形成液晶相,随着混合摩尔比OTAB/SOS接近于1,液晶结构由六角相转层状相,同时夹杂少量沉淀物;在中等浓度时,任意混合摩尔比例下皆为均相透明溶液;在低浓度下,在很宽的OTAB/SOS混合摩尔比的范围,出现双水相,其中的表面活性剂稀薄相,为不同大小的胶团与囊泡组成的稀溶液,另一表面活性剂富集相中则为数密度很大的囊泡聚集体,富集相对油溶性染料的增溶作用比非富集相高得多.     

Salting-out surfactant extraction of porphyrins and metalloporphyrin from aqueous non-ionic surfactant solutions

A number of cloud point temperature-depressing electrolytes have been investigated for the separation of a non-ionic surfactant (Triton X-100) from aqueous solutions and the corresponding extraction of the organic solutes into the smaller volume surfactant-rich phase using the salting-out method. High extraction efficiencies and preconcentration factors were obtained at room temperature for the extraction of several hydrophilic and hydrophobic metal-free porphyrins (uroporphyrin, coproporphyrin, protoporphyrin and hematoporphyrin) and one metalloporphyrin (iron-protoporphyrin) that were dissolved in the aqueous non-ionic surfactant solutions. Possible mechanisms responsible for the efficient extraction of these important biological molecules into the surfactant-rich layer are discussed.     

Micelle-mediated extraction and preconcentration of ginsenosides from Chinese herbal medicine

The feasibility of employing micelle-mediated extraction as an alternative and effective method for the solubilization, purification and/or preconcentration of active ingredients from herbal products is demonstrated for the first time using the root of American ginseng as a model. When compared to methanol and water, an aqueous surfactant solution containing 10% Triton X-100 yielded faster kinetics and higher recovery for the extraction of various ginsenosides. An experimental design approach (uniform design) was demonstrated as a novel and useful method for the optimization of experimental factors involved in the micelle-mediated extraction process. For the preconcentration of ginsenosides prior to chromatographic determination, a salting-out agent (sodium sulfate) was employed to make the efficient cloud point extraction of both hydrophobic and hydrophilic ginsenosides into the surfactant-rich phase possible, as well as to increase the preconcentration factor by reducing the volume of the surfactant-rich phase.     

Dual-cloud point extraction as a preconcentration and clean-up technique for capillary electrophoresis speciation analysis of mercury

A novel dual-cloud point extraction (dCPE) technique is proposed in this paper for the sample pretreatment of capillary electrophoresis (CE) speciation analysis of mercury. In dCPE, cloud point was carried out twice in a sample pretreatment. First, four mercury species, methylmercury (MeHg), ethylmercury (EtHg), phenylmercury (PhHg), and inorganic mercury (Hg(II)) formed hydrophobic complexes with 1-(2-pyridylazo)-2-naphthol (PAN). After heating and centrifuging, the complexes were extracted into the formed Triton X-114 surfactant-rich phase. Instead of the direct injection or analysis, the surfactant-rich phase containing the four Hg species was treated with 150 microL 0.1% (m/v) l-cysteine aqueous solution. The four Hg species were then transferred back into aqueous phase by forming hydrophilic Hg-l-cysteine complexes. After dCPE, the aqueous phase containing the Hg-l-cysteine complexes was subjected into electrophoretic capillary for mercury speciation analysis. Because the concentration of Triton X-114 in the extract after dCPE was only around critical micelle concentration, the adsorption of surfactant on the capillary wall and its possible influence on the sample injection and separation in traditional CPE were eliminated. Plus, the hydrophobic interfering species were removed thoroughly by using dCPE resulted in significant improvement in analysis selectivity. Using 10 mL sample, 17, 15, 45, and 52 of preconcentration factors for EtHg, MeHg, PhHg, and Hg(II) were obtained. With CE separation and on-line UV detection, the detection limits were 45.2, 47.5, 4.1, and 10.0 microg L(-1) (as Hg) for EtHg, MeHg, PhHg, and Hg(II), respectively. As an analysis method, the present dCPE-CE with UV detection obtained similar detection limits as of some CE-inductively coupled plasma mass spectrometry (ICPMS) hyphenation technique, but with simple instrumental setup and obviously low costs. Its utilization for Hg speciation was validated by the analysis of the spiked natural water and tilapia muscle samples.     

Lyophilic properties of surfactant-rich phases of polyethoxylated alkylphenols formed at cloud point temperature

The influence of the concentration conditions, solutions acidity, and electrolyte additions on the lyophilic properties of the surfactant-rich phases of polyethoxylated alkylphenols OP-7 and OP-10 formed at cloud point temperature were studied. The lyophilic properties of surfactant-rich phases were determined by estimating of their effective hydration values and solvation free energy of methylene and carboxyl groups at cloud point extraction of aliphatic monocarboxylic acids. It was shown that the surfactant-rich phases formed from the dilute surfactant solutions have more hydrophobic properties than the phases formed from the high concentrated solutions. The possibility of changing the lyophilic properties of surfactant-rich phases by electrolyte additions was shown: complex formation between electrolyte cation and the polyoxyethylene chain of the surfactant increases the hydrophilic properties of the surfactant-rich phases. Calculations of the solvation free energy of methylene and carboxylic fragments of the aliphatic carboxylic acids at micellar extraction showed the uniqueness of the surfactant-rich phases which are able to energetically advantageously extract both hydrophilic and hydrophobic molecules of substrates.     

浊点萃取-流动注射电感耦合等离子体原子发射光谱法同时测定水中镉钴铜镍锌

本文提出了浊点萃取-流动注射电感耦合等离子体原子发射光谱（FI—ICP—AES）法同时测定水中镉、钴、铜、镍、锌的新方法。利用5-Br—PADAP将待测金属离子转化为水不溶性的螯合物，并萃取到表面活性剂Triton X-114的浓缩相，以乙醇-硝酸溶液稀释含富集离子的浓缩相，并以FI—ICP-AES法测定。考察了流动注射进样体积、积分时间、萃取体系介质酸度、螯合剂和表面活性剂用量等实验条件的影响。在折衷条件下，镉、钴、铜、镍和锌的浓缩倍率可达18、10、16、10和8，检出限分别为0．7μg／L、1．6μg／L、1．3μg／L、5．7μg／L、3．2μg／L。方法成功应用于自来水、河水和海水中痕量镉、钴、铜、镍和锌的分析。在0．02mg／L和0．10mg／L二个水平进行加入回收试验，回收率在80％与118％之间。     

Aqueous two-phase system of an anionic gemini surfactant and a cationic conventional surfactant mixture

The aqueous two-phase system formed by the mixture of dodecyltrimethylammonium bromide (DTAB) with a gemini surfactant O,O′-bis(sodium 2-lauricate)-p-benzenediol (C₁₁pPHCNa) has been studied. Two two-phase regions were observed, one was a wide region in the cationic surfactant-rich side and the other in the vicinity of R = 1:1, where R is the mixing mole ratio of DTAB to C₁₁pPHCNa in global solution. Multi-lamellar vesicles are formed in the concentrated upper phase of cationic surfactant-rich systems and spherical aggregates in the concentrated bottom phase at R = 1:1. The microstructure of the solution and the phase behavior of the aqueous two-phase system strongly depended on the total concentration and the composition of the system.     

Aqueous two-phase extraction system of sodium perfluorooctanoate and dodecyltriethylammonium bromide mixture and its application to porphyrins and dyes

A new aqueous two-phase system is developed consisting of sodium perfluorooctanoate (SPFO) and dodecyltriethylammonium bromide (C₁₂NE) cationic–anionic surfactant mixture. The two phases with a clear interfacial boundary formed when SPFO to C₁₂NE molar ratio is 1.2:1 in the presence of 5% (v/v) nitric acid. The top phase is transparent and the bottom phase is opalescent. Extractions of dyes, porphyrin compounds with the two-phase system were performed. The results show that hydrophobic molecules were extracted into the surfactant-rich bottom phase with high extraction efficiencies. Positively charged porphyrins were extracted into the bottom phase with higher extraction efficiencies than negatively charged porphyrins. Such a new anionic surfactant two-phase system would be complementary to the C₁₂NE–SDS (sodium dodecyl sulfate) cationic two-phase which has been proven to be effective for extractions of porphyrins with substituted groups like carboxyl or sulfonic acid groups.     

Combination of cloud point extraction and flame atomic absorption spectrometry for preconcentration and determination of trace iron in environmental and biological samples

In the presented work, the conditions for cloud point extraction of iron from aqueous solutions using 7-iodo-8-hydroxyquinolin-5-sulphonic acid (Ferron) was investigated and optimized. The procedure is based on the separation of its ferron complex into the micellar media by adding the surfactant Triton X-114. After phase separation, the surfactant-rich phase was dissolved with 1.0 M HNO3 in methanol. Iron was determined by flame atomic absorption spectrometry. Optimization of the pH, ligand and surfactant quantities, incubation time, temperature, viscosity, sample volume, and interfering ions were investigated. The effects of the matrix ions were also examined. The detection limits for three times the standard deviations of the blank for iron was 0.4 ng m L-1, enrichment factor of 19.6 and preconcentration factor of 30 could be achieved. The validity of cloud point extraction was checked by employing real samples including soil, blood, spinach, milk, meat, liver and orange juice samples using the standard addition method, which gave satisfactory results.In the presented work, the conditions for cloud point extraction of iron from aqueous solutions using 7-iodo-8-hydroxyquinolin-5-sulphonic acid (Ferron) was investigated and optimized. The procedure is based on the separation of its ferron complex into the micellar media by adding the surfactant Triton X-114. After phase separation, the surfactant-rich phase was dissolved with 1.0 M HNO₃ in methanol. Iron was determined by flame atomic absorption spectrometry. Optimization of the pH, ligand and surfactant quantities, incubation time, temperature, viscosity, sample volume, and interfering ions were investigated. The effects of the matrix ions were also examined. The detection limits for three times the standard deviations of the blank for iron was 0.4 ng m L⁻¹, enrichment factor of 19.6 and preconcentration factor of 30 could be achieved. The validity of cloud point extraction was checked by employing real samples including soil, blood, spinach, milk, meat, liver and orange juice samples using the standard addition method, which gave satisfactory results.      

Derivatization, extraction and concentration of amino acids and peptides by using organic/aqueous phases in capillary electrophoresis with fluorescence detection

We report a novel method that facilitates sample pretreatment and detection in amino acid analysis by coupling solvent extraction with capillary electrophoresis. Amino acids and peptides were fluorescently labeled, concentrated into an organic solvent, and then separated by capillary zone electrophoresis with fluorescence detection. To achieve this, acetophenone was first employed to dissolve the derivatizing reagent, fluorescamine. The products, which possessed both hydrophilic and hydrophobic moieties, could be extracted and concentrated into the organic phase by suppressing the deprotonation of carboxyl groups, thus enhancing the hydrophobicity of the resulting molecules through pH modification in the aqueous solution. Furthermore, by fine-tuning the pH value, individual amino acids and short peptide molecules could be separated selectively from the sample bulk. This convenient, chemically controllable concentration technique may be useful in sample concentration and purification of biologically related samples such as amino acids and short peptides.     

Determination of noble metals in biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry,following cloud point extraction

A simple separation procedure for noble metals based on cloud point extraction is proposed. The analyte ions in aqueous acidic solution, obtained by the acid digestion of the samples, were complexed with O,O-diethyl-dithiophosphate and Triton X-114 was added as a non-ionic surfactant. By increasing the temperature up to the cloud point, a phase separation occurs, resulting in an aqueous phase and a surfactant-rich phase containing most of the analytes that were complexed. The metals in the surfactant-rich phase were determined by electrothermal vaporization inductively coupled plasma mass spectrometry. The extraction conditions as well as the instrumental parameters were optimized. Enrichment factors ranging from 7 (Rh) to 60 (Pt) and limits of detection from 0.6 (Pt) to 3.0 ng l⁻¹ (Rh) were obtained in the digested samples. The extraction was not efficient for Ir. Among the reference materials analyzed in this work, only one (SRM 2670, urine) presented recommended values for Au and Pt. Due to the non-availability of adequate CRMs, accuracy was assessed by spiking known analyte amounts to the acid digests. Recoveries close to 100% were observed for all the studied elements but Ru. Poor agreement between found and recommended values was observed for non-digested urine sample, probably due to the carrier effect of co-extracted residual matrix components. However, good agreement was reached after urine acid mineralization.     

表面活性剂阴离子双水相新体系及其对卟啉、染料的萃取

由阴阳离子型表面活性剂水溶液混合形成的双水相［１,２］是水相分离技术中的一个新分支．ＺＨＡＯ等［２］将阴阳离子表面活性剂过量的体系分别称为阴阳离子双水相．由溴化十二烷基三乙铵（Ｃ１２ＮＥ）和十二烷基硫酸钠（ＳＤＳ）组成的阳离子双水相对蛋白质［１］、酶［３］、氨基酸［４］和卟啉［５,６］等的萃取分离已有报道．与阳离子双水相比较,阴离子双水相分相时间慢,其萃取应用研究尚未见报道．本文在详细研究了ＳＤＳ－Ｃ１２ＮＥ阴离子双水相的基础上,将全氟型阴离子表面活性剂全氟辛酸钠（ＳＰＦＯ）引入这类水相分离体系…     

An Efficient Method for the Conjugation of Hydrophilic and Hydrophobic Components by Solid‐Phase‐Assisted Disulfide Ligation

Chemical conjugation between hydrophilic and hydrophobic components is difficult because of their extremely different solubility. Herein, we report a new versatile method with a solid‐phase‐assisted disulfide ligation to overcome the difficulty of conjugation attributed to solubility. The method involves two steps in a one‐pot process: 1) loading of a hydrophobic molecule onto a resin in an organic solvent, and 2) release of the solid‐supported hydrophobic molecule as a conjugate with a hydrophilic molecule into an aqueous solvent. This strategy allows the use of a suitable solvent system for the substrates in each step. Conjugates of a water‐insoluble drug, plinabulin, with hydrophilic carriers that could not be prepared by solution‐phase reactions were obtained in moderate yields (29–45 %). This strategy is widely applicable to the conjugation of compounds with solubility problems.     

Micelle-mediated extraction

The extraction technique based on phase separation in aqueous micellar solutions is reviewed. The technique has now been utilized for separation and preconcentration of metal chelates, organic compounds, and proteins. Additionally, the phase behavior of the micellar solutions and recent advances in the phase separation technique are also described. In the extraction of metal chelates, distribution equilibria are considered. In contrast to conventional solvent extraction, the distribution of metal chelates into a condensed surfactant phase (surfactant-rich phase) was dependent on metal ions. Proteins were extractable into the surfactant-rich phase according to their hydrophobicity. The recent use of affinity ligands and water-soluble polymers for controlling extractability of proteins are also introduced.     

pH-mediated dual-cloud point extraction as a preconcentration and clean-up technique for capillary electrophoresis determination of phenol and m-nitrophenol

pH-mediated dual-cloud point extraction (dCPE) technique for capillary electrophoresis (CE) determination of phenol and m-nitrophenol is proposed in this paper. This technique for the preconcentration and clean-up of the two analytes includes two steps through simple pH-mediation. The analytes are transferred into surfactant-rich phase in the first step (under acidic condition) with Triton X-114 as the extractant because the two analytes become hydrophobic in acidic solution. They were back-extracted into alkaline aqueous phase in the second cloud point step. Because the concentration of Triton X-114 in the final aqueous solution after dCPE is only around critical micelle concentration, its adsorption on the inner wall of capillary and its possible influence on electrophoretic separation are eliminated. Baseline separation of phenol and m-nitrophenol is realized in a 60 cm x 75 microm i.d. capillary at 18 kV using 50 mM boric acid solution (pH 9.5). The preconcentration factors are 24.0 for phenol and 22.5 for m-nitrophenol. The detection limits of phenol and m-nitrophenol are 2.0 x 10(-6) mol L(-1) and 2.5 x 10(-6) mol L(-1), respectively. The proposed method was successfully applied to the determination of two analytes in spiked natural water samples.     

Phase behavior and molecular thermodynamics of coacervation in oppositely charged polyelectrolyte/surfactant systems: a cationic polymer JR 400 and anionic surfactant SDS mixture

Coacervation in mixtures of polyelectrolytes and surfactants with opposite charge is common in nature and is also technologically important to consumer health care products. To understand the complexation behavior of these systems better, we combine multiple experimental techniques to systematically study the polymer/surfactant binding interactions and the phase behavior of anionic sodium dodecyl sulfate (SDS) surfactant in cationic JR 400 polymer aqueous solutions. The phase-behavior study resolves a discrepancy in the literature by identifying a metastable phase between the differing redissolution phase boundaries reported in the literature for the surfactant-rich regime. Isothermal titration calorimetry analyzed within the framework of the simple Satake-Yang model identifies binding parameters for the surfactant-lean phase, whereas a calculation for polymer-bound micelles coexisting with free micelles is analyzed in the surfactant-rich redissolution regime. This analysis provides a preliminary understanding of the interactions governing the observed phase behavior. The resulting thermodynamic properties, including binding constants and the molar Gibbs free energies, enthalpies, and entropies, identify the relative importance of both hydrophobic and electrostatic interactions and provide a first approximation for the corresponding microstructures in the different phases. Our study also addresses the stability and metastability of oppositely charged polyelectrolytes and surfactant mixtures.     

The 4-aminoantipyrine Method Revisited: Determination of Trace Phenols by Micellar Assisted Preconcentration

The traditional method for phenol analysis based on the oxidizing coupling of 4-aminoantipyrine (4-APP) with phenol in alkaline solution is re-evaluated in this study in combination with micellar assisted preconcentration (cloud point extraction). The method employs the conventional reaction pathway while extraction is facilitated by surfactant based precipitation, during which the nonpolar derivative of 4-AAP-phenol is entrapped in the micelles and concentrated into a surfactant-rich phase. The latter is the re-solubilized and the complex is quantified spectrophotometrically in the presence of a surfactant. Compared to the traditional method the modification proposed offers certain analytical advantages like massive analysis of many samples, lower detection limits and shorter time of analysis. The method was applied in various samples of different origin with satisfactory results.     

Dynamics of nonionic surfactant-rich phase separation and recovery of dyes

Cloud point separation of selected dyes was studied. The use of dyes made possible observation of the dynamics of surfactant-rich phase separation by color video. The pictures were interpreted by means of ImageC software and degrees of whiteness were calculated. It was found that separation was slow and equilibrium was not achieved even after a period of more than 10 h. The separated surfactant-rich phase had a heterogeneous structure. The globules of the surfactant-rich phase were also observed in the micellar aqueous phase. The surfactant concentration could be as high as one or two orders of magnitude above the expected cmc values and was not decreased to critical micelle concentration by centrifugation. The presence of sodium chloride was important and improved separation. Separation of dyes was in the range 73-98% and depended upon the surfactant, the temperature, the electrolyte content, and the dye. In each system considered, appropriate conditions had to be selected to obtain high recovery of the dye. The presence of the electrolyte was the most important parameter and it improved the separation of dyes. However, addition of the electrolyte could also account for precipitation of the dyes, as observed for the systems containing Direct Pink. The best recoveries were observed for Direct Yellow and oxyethylated nonylphenol (98% at 55 degrees C in the presence of NaCl). Centrifugation gave recoveries similar to those for prolonged heating but it shortened the time of phase separation.     

Emulsion pathways to composite polymeric membranes for separation processes

A novel method for the preparation of selective composite membranes from emulsions is suggested. The dispersed phase is chosen to yield a polymer soluble in those components for which the membrane should be selective; the continuous phase, on the other hand, is selected to yield a polymer that is insoluble in any of the components of the mixture. Conventional emulsions (which have a maximum dispersed phase volume fraction of 0.74) or microemulsions can be employed to generate composites. However, concentrated emulsions which allow volume fractions as large as 0.99 are most suitable as precursors to selective and efficient membranes. These concentrated emulsions have the appearance of gels with a structure similar to that of foams. The relatively high permeabilities obtained with the resultant membranes are due to the small thickness of the films of the continuous phase. A concentrated emulsion of a hydrophobic (hydrophilic) monomer dispersed in a hydrophilic (hydrophobic) continuous phase is first prepared at room temperature, with suitable initiators in each phase for later polymerization, and with an appropriate dispersant in the continuous phase. To ensure the stability of the emulsion, the hydrophilic monomer is, in general, replaced by monomer plus water. On heating the gel at 50 °C, polymerization occurs in both phases and the emulsion transforms into a composite polymer membrane. As examples, composite membranes containing polystyrene as the dispersed phase and polyacrylamide as the continuous phase are used to separate toluene from cyclohexane, while other composite membranes containing acrylamide as the dispersed phase and a crosslinked polystyrene as the continuous phase are used to separate water from ethanol.Lecture presented at the Colburn Symposium, University of Delaware, October 19, 1988.     

Equilibrium partition of polycyclic aromatic hydrocarbons in cloud point extraction with a silicone surfactant

In the cloud point extraction (CPE) process with PEG/PPG-18/18 dimethicone, the flexible chain structure of the silicone surfactant efficiently decreased the water content remaining in the surfactant-rich phase, compared with conventional nonionic surfactants, represented by Triton X-114. Meanwhile, the phase volume ratio of surfactant-rich phase to aqueous phase obtained in the silicone surfactant CPE system was found to be maintained at a low value with increasing surfactant concentration; whereas a rapid increase tendency was commonly observed in that of other nonionic surfactants. Based on these advantages, the equilibrium partition of three polycyclic aromatic hydrocarbons (PAHs), anthracene, phenanthrene and pyrene, was studied in the CPE process with PEG/PPG-18/18 dimethicone. Equilibrium parameters, including preconcentration factor, distribution coefficient and recovery, were determined, and the performance was compared with that of another related CPE research, where Tergitol 15-S-7 was used. Due to the low surfactant-rich phase volume, higher concentrations of the three PAHs in the surfactant-rich phase, and the resulting higher preconcentration factors and distribution coefficients were able to be achieved at the same time. Moreover, the great performance was able to be maintained even at a high surfactant concentration or PAHs initial concentration.