Headgroup effect on silane structures at buried polymer/silane and polymer/polymer interfaces and their relations to adhesion

Sum frequency generation (SFG) vibrational spectroscopy was used to study the effect of silane headgroups on the molecular interactions that occur between poly(ethylene terephthalate) (PET) and various epoxy silanes at the PET/silane and PET/silicone interfaces. Three different silanes were investigated: (3-glycidoxypropyl) trimethoxysilane (γ-GPS), (3-glycidoxypropyl) methyl-dimethoxysilane (γ-GPMS), and (3-glycidoxypropyl) dimethyl-methoxysilane (γ-GPDMS). These silanes share the same backbone and epoxy end group but have different headgroups. SFG was used to examine the interfaces between PET and each of these silanes, as well as silanes mixed with methylvinylsiloxanol (MVS). We also examined the interfaces between PET and uncured or cured silicone with silanes or silane-MVS mixtures. Silanes with different headgroups were found to exhibit a variety of methoxy group interfacial segregation and ordering behaviors at various interfaces. The effect of MVS was also dependent upon silane headgroup choice, and the interfacial molecular structures of silane methoxy headgroups were found to differ at PET/silane and PET/silicone interfaces. Epoxy silanes have been widely used as adhesion promoters for polymer adhesives; therefore, the molecular structures probed using SFG were correlated to adhesion testing results to understand the molecular mechanisms of silicone-polymer adhesion. Our results demonstrated that silane methoxy headgroups play important roles in adhesion at the PET/silicone interfaces. The presence of MVS can change interfacial methoxy segregation and ordering, leading to different adhesion strengths.     

Entropically mediated polyolefin blend segregation at buried sapphire and air interfaces investigated by infrared-visible sum frequency generation vibrational spectroscopy

The segregation behavior of binary polymer blends at hydrophilic solid sapphire and air interfaces was investigated by infrared-visible sum frequency generation (SFG) vibrational spectroscopy. SFG spectra were collected from a bulk miscible blend consisting of identical molecular weight (approximately 54,000) and similar surface free energy (29-35 dyn/cm) components of atactic polypropylene (aPP) and aspecific poly(ethylene-co-propylene) rubber (aEPR). Characteristic CH resonances of the blend were contrasted with those of the individual components at both buried (sapphire/polymer) and free (air/polymer) interfaces. Preferential segregation of the aPP component was observed after annealing at both air/polymer and sapphire/polymer interfaces. SFG spectra revealed ordering of the polymer backbone segments with the methylene (CH2) groups perpendicular to the surface at the sapphire interface and the methyl (CH3) groups upright at the air interface. The SFG results indicate that the surface composition can be determined from the peak intensities that are characteristic of each component and that conformational entropy played a likely role in surface segregation. aPP occupied a smaller free volume at the surface because of a statistically smaller segment length (aPP is more flexible and has a shorter length). In addition, the high density of the ordered CH3 side branches enhanced the surface activity by allowing the long-chain backbone segments of aPP to order at the surface.     

Molecular restructuring at poly(n-butyl methacrylate) and poly(methyl methacrylate) surfaces due to compression by a sapphire prism studied by infrared-visible sum frequency generation vibrational spectroscopy

Infrared-visible sum frequency generation (SFG) vibrational spectroscopy, performed in visible wavelength total internal reflection (TIR) geometry, was used to determine the molecular structures of poly(n-butyl methacrylate) (PBMA) and poly(methyl methacrylate) (PMMA) surfaces in air and in contact with a smooth sapphire surface with and without the application of pressure. C-H vibrational resonances were probed optically to nondestructively examine the buried polymer/sapphire interfaces and obtain information about the molecular orientation in situ. These findings are contrasted with those of the same polymers cast from a toluene solution directly on the sapphire prism surface and annealed. Compared to polymer surface conformation in air, the SFG spectra of the deformed (compressed) PBMA at the sapphire interface illustrate that the ester butyl side chain restructures and tilts away from the surface normal. However, the molecular conformation in the similarly deformed PMMA at the sapphire interface is identical to that obtained in air, which is dominated by the upright-oriented ester methyl side chains. For PBMA and PMMA spin cast on sapphire and annealed, the surface structure of the undeformed PBMA at the sapphire interface is identical to that of the deformed PBMA at the sapphire interface, while the PMMA conformation is different and shows alpha-methyl group ordering. Since the glass transition temperature of PBMA is below room temperature, the rubbery state of PBMA demonstrates a melt-like behavior, evidenced by the fact that PBMA is in conformation chemical equilibrium at the sapphire surface even under compression. Due to the high glass transition temperature of PMMA, compression freezes PMMA in a metastable state, revealed by the restructured molecular conformation when annealed against the sapphire surface. The results of this study demonstrate that structural changes at buried polymer surfaces due to the application of contact pressure can be detected in situ by TIR-SFG vibrational spectroscopy.     

隐藏高分子界面及生物界面分子结构的和频振动光谱研究

界面的分子结构决定界面的性质.为了以优化界面的结构来改进材料的性质,原位实时地研究界面的分子结构是很重要的.近年来和频振动光谱已发展成为一个很有效及独特的手段来研究隐藏界面的分子结构,例如液/液界面、固/液界面及固/固界面等.这篇综述讨论了和频振动光谱在研究高分子界面及生物界面等复杂界面的分子结构上的应用.具体说来,本文论述了高分子表面在水里的分子结构变化,高分子及模型粘合促进剂硅烷在界面相互作用的分子机理和隐藏的高分子/高分子及高分子/金属界面的结构.另外,此文还将介绍不同二级结构的多肽及几个有代表性的蛋白分子在界面的结构.界面在诸如化学、生物、物理、材料科学及工程和纳米技术等许多领域都很重要.发展一个独特的能原位研究隐藏界面的分子结构的技术会有力地促进这些领域的研究及跨学科研究的发展.     

Sum frequency generation and coherent anti-Stokes Raman spectroscopic studies on plasma-treated plasticized polyvinyl chloride films

Polyvinyl chloride (PVC) is a widely used polymer to which various phthalates are extensively applied as plasticizers. PVC materials are often treated with plasma to vary the hydrophobicity or for cleaning purposes, but little is known of the nature of the surface molecular structures after treatment. This research characterizes molecular surface structures of PVC and bis-2-ethylhexyl phthalate (DEHP)-plasticized PVC films in air before annealing, after annealing, and after exposure to air-generated glow discharge plasma using sum frequency generation (SFG) vibrational spectroscopy. In addition, we compare the vibrational molecular signatures on the surfaces of PVC with DEHP (at a variety of percent loadings) to those of the bulk detected using coherent anti-Stokes Raman scattering (CARS). X-ray photoelectron spectroscopy (XPS) and contact angle measurements have been used to analyze PVC surfaces to supplement SFG data. Our results indicate that DEHP was found on the surfaces of PVC films even at low weight percentages (5 wt %) and that DEHP segregates on surfaces after annealing. The treatment of these films with glow discharge plasma resulted in surface-sensitive reactions involving the removal of chlorine atoms, the addition of oxygen atoms, and C-H bond rearrangement. CARS data demonstrate that the bulk of our films remained undisturbed during the plasma treatment. For the first time, we probed the molecular structure of the surface and the bulk of a PVC material using combined SFG and CARS studies on the same sample in exactly the same environment. In addition, the methodology used in this research can be applied to characterize various plasticizers in a wide variety of polymer systems to understand their surface and bulk structures before and after systematic applications of heat, plasma, or other treatments.     

Detection of amide I signals of interfacial proteins in situ using SFG

In this Communication, we demonstrate the novel observation that it is feasible to collect amide signals from polymer/protein solution interfaces in situ using sum frequency generation (SFG) vibrational spectroscopy. Such SFG amide signals allow for acquisition of more detailed molecular level information of entire interfacial protein structures. Proteins investigated include bovine serum albumin, mussel protein mefp-2, factor XIIa, and ubiquitin. Our studies indicate that different proteins generate different SFG amide signals at the polystyrene/protein solution interface, showing that they have different interfacial coverage, secondary structure, or orientation.     

Rubbing-induced anisotropy of long alkyl side chains at polyimide surfaces

Molecular organization at polyimide surfaces used as alignment layers in liquid crystal displays was investigated using vibrational sum frequency generation (SFG) spectroscopy. We focus on the orientation of the long alkyl side groups at the polymer surface using polarization-selected SFG spectra of the CH(3)- and CH(2)-stretch modes of the side chain. Mechanical rubbing and baking, an accepted industrial procedure used to produce pretilt of the liquid crystal, was found to induce pronounced azimuthal anisotropy in the orientational distribution of the alkyl side chains. Orientational analysis of the SFG vibrational spectra in terms of the azimuthal and tilt angles (in and out of plane, respectively) of the alkyl side chains shows their preferential tilt along the rubbing direction, with the azimuthal distribution narrower for stronger rubbed polymer samples.     

Electronic and conformational properties of the conjugated polymer MEH-PPV at a buried film/solid interface investigated by two-dimensional IR-visible sum frequency generation

We present the first measurement of the buried surface electronic states of the conjugated polymer poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylenevinylene] (MEH-PPV) using two-dimensional (2D) IR-visible sum frequency generation (SFG). SFG electronic spectra were obtained by scanning the frequencies of both incident visible and IR beams and used to study the surface electronic transitions associated with the C-C stretching of benzene rings located at the backbone of MEH-PPV. Because of the surface confinement effects, the polymer conformation, and consequently the electronic states, at the film/solid interface are different from those of the bulk film. Theoretical analysis based on an oligomer model was employed to estimate the conjugation-length distributions of MEH-PPV at interfaces. Assuming a Gaussian conjugation-length distribution, it was found that the conjugation-length distribution at the MEH-PPV/solid interface was centered at 5.8 monomer units. Similar surface effects were also observed at the air/polymer interface, with a shorter average conjugation length of 5.1 monomer units.     

Molecular level studies of polymer behaviors at the water interface using sum frequency generation vibrational spectroscopy

Industrial plastics, biomedical polymers and numerous other polymeric systems are contacted with water for everyday functions and after disposal. Probing the interfacial molecular interactions between widely used polymers and water yields valuable information that can be extrapolated to macroscopic polymer/water interfacial behaviors so scientists can better understand polymer bio-compatibility, hygroscopic tendencies and improve upon beneficial polymer behavior in water. There is an ongoing concerted effort to elucidate the molecular level behaviors of polymers in water by using sum frequency generation vibrational spectroscopy (SFG). SFG stands out for its utility in probing buried interfaces in situ and in real time without disrupting interfacial chemistry. Included in this review are SFG water interfacial studies performed on poly(methacrylate) and (acrylate)s, poly(dimethyl siloxane)s, poly(ethylene glycol)s, poly(electrolyte)s and other polymer types. The driving forces behind common water/polymer interfacial molecular features will be discussed as well as unique molecular reorientation phenomena and resulting macroscopic behaviors from microscopic polymer rearrangement. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Polymer surface science

Molecular level studies of the structure and mechanical properties of polymer surfaces have been carried out by sum frequency generation (SFG) surface vibrational spectroscopy and atomic force microscopy (AFM). The surfaces of different grades of polyethylene and polypropylene have been characterized-including during the glass transition and when mechanically stretched. Copolymers that have hard and soft segments with different glass transition temperatures show phase separation, an effect of hydrogen bonding between the hard and soft segments, that influences their adhesive and friction properties. AFM and SFG show that low surface energy additives migrate to the surface and alter the surface mechanical properties. Polymers, where the chemical nature of the end groups is different from the backbone, show surface segregation of the hydrophobic part of the chain in air and the hydrophilic part in water. Likewise, in miscible polymer blends, surface segregation of the more hydrophobic component in air and the more hydrophilic component in water is observed. This area of surface science requires increased attention because of the predominance of polymers as structural materials and as biomaterials.     

Liquid crystal alignment capabilities on rubbed organic solvent soluble polyimide surfaces with trifluoromethyl moieties

High pretilt angles, polar anchoring energy (out of plane-tilt), and surface ordering in the nematic liquid crystal 4-n-pentyl-4'-cyanobiphenyl (5CB) were investigated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. It was found that the pretilt angle of 5CB is about 15° in the wide rubbing region of rubbed soluble PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings. It is suggested that the microscopic surface structure of the polymer contributes to the LC pretilt angle generation at the surface. Also, the polar anchoring energy of 5CB is dependent on the molecular structure of these unidirectionally rubbed soluble PI surfaces. The polar anchoring strength of 5CB on rubbed soluble PI surfaces is as weak with trifluoromethyl moieties attached to the lateral benzene rings weak as when the trifluoromethyl moieties are attached to the polymer backbone. Finally, the polar anchoring energy of 5CB strongly depends on the surface ordering of rubbed soluble PI surfaces.     

Liquid crystal alignment capabilities on rubbed organic solvent soluble polyimide surfaces with trifluoromethyl moieties

High pretilt angles, polar anchoring energy (out of plane-tilt), and surface ordering in the nematic liquid crystal 4-n-pentyl-4'-cyanobiphenyl (5CB) were investigated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. It was found that the pretilt angle of 5CB is about 15° in the wide rubbing region of rubbed soluble PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings. It is suggested that the microscopic surface structure of the polymer contributes to the LC pretilt angle generation at the surface. Also, the polar anchoring energy of 5CB is dependent on the molecular structure of these unidirectionally rubbed soluble PI surfaces. The polar anchoring strength of 5CB on rubbed soluble PI surfaces is as weak with trifluoromethyl moieties attached to the lateral benzene rings weak as when the trifluoromethyl moieties are attached to the polymer backbone. Finally, the polar anchoring energy of 5CB strongly depends on the surface ordering of rubbed soluble PI surfaces.     

Surface structures and properties of polystyrene/poly(methyl methacrylate) blends and copolymers

Sum frequency generation (SFG) vibrational spectroscopy has been applied to study the molecular surface structures of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends and the copolymer between PS and PMMA (PS-co-PMMA) in air, supplemented by atomic force microscopy (AFM) and contact angle goniometer. Both the blend and the copolymer have equal weight amounts of the two components. SFG results show that both components, PS and PMMA, can segregate to the surface of the blend and the copolymer before annealing, although PMMA has a slightly higher surface tension. Upon annealing both SFG results and contact angle measurements indicate that the PS segregates to the surface of the PS/PMMA blend more but no change occurs on the PS-co-PMMA surface. AFM images show that the copolymer surface is flat but the 1:1 PS/PMMA blend has a rougher surface with island like domains present. The annealing effect on the blend surface morphology has also been investigated. We collected amide SFG signals from interfacial fibrinogen molecules at the copolymer or blend/protein solution interfaces as a function of time. Different time-dependent SFG signal changes have been observed, showing that different surfaces of the blend and the copolymer mediate fibrinogen adsorption behavior differently.     

Probing alpha-helical and beta-sheet structures of peptides at solid/liquid interfaces with SFG

We demonstrated that sum frequency generation (SFG) vibrational spectroscopy can distinguish different secondary structures of proteins or peptides adsorbed at solid/liquid interfaces. The SFG spectrum for tachyplesin I at the polystyrene (PS)/solution interface has a fingerprint peak corresponding to the B1/B3 mode of the antiparallel beta-sheet. This peak disappeared upon the addition of dithiothreitol, which can disrupt the beta-sheet structure. The SFG spectrum indicative of the MSI594 alpha-helical structure was observed at the PS/MSI594 solution interface. This research validates SFG as a powerful technique for revealing detailed secondary structures of interfacial proteins and peptides.     

原位探测防污高分子材料与液体界面的分子结构

Marine organisms such as plants, algae or small animals can adhere to surfaces of materials that are submerged in ocean. The accumulation of these organisms on surfaces is a marine biofouling process that has considerable adverse effects. Marine biofouling on ship hulls can cause severe fuel consumption increase. Investigations on antifouling polymers are therefore becoming important research topics for marine vessel operations. Antifouling polymers can be applied as coating layers on the ship hull, protecting it against the settlement and growth of sea organisms. Polyethylene glycol (PEG) is a hydrophilic polymer that can effectively resist the accumulation of marine organisms. PEG-based antifouling coatings have therefore been extensively researched and developed. However, the inferior stability of PEG makes it subject to degradation, rendering it ineffective for long-term services. Zwitterionic polymers have also emerged as promising antifouling materials in recent years. These polymers consist of both positively charged and negatively charged functional groups. Various zwitterionic polymers have been demonstrated to exhibit exceptional antifouling properties. Previously, surface characterizations of zwitterionic polymers have revealed that strong surface hydration is critical for their antifouling properties. In addition to these hydrophilic polymers, amphiphilic materials have also been developed as potential antifouling coatings. Both hydrophobic and hydrophilic functional groups are incorporated into the backbones or sidechains of these polymers. It has been demonstrated that the antifouling performance can be enhanced by precisely controlling the sequence of the hydrophobic-hydrophilic functionalities. Since biofouling generally occurs at the outer surface of the coatings, the antifouling properties of these coatings are closely related to their surface characteristics in water. Therefore, understanding of the surface molecular structures of antifouling materials is imperative for their future developments. In this review, we will summarize our recent advancements of antifouling material surface analysis using sum frequency generation (SFG) vibrational spectroscopy. SFG is a surface-sensitive technique which can provide molecular information of water and polymer structures at interfaces in situ in real time. The antifouling polymers we will review include zwitterionic polymer brushes, mixed charged polymers, and amphiphilic polypeptoids. Interfacial hydration studies of these polymers by SFG will be presented. The salt effect on antifouling polymer surface hydration will also be discussed. In addition, the interactions between antifouling materials and protein molecules as well as algae will be reviewed. The above research clearly established strong correlations between strong surface hydration and good antifouling properties. It also demonstrated that SFG is a powerful technique to provide molecular level understanding of polymer antifouling mechanisms.     

Demonstrating the feasibility of monitoring the molecular-level structures of moving polymer/silane interfaces during silane diffusion using SFG

In this paper, the feasibility of monitoring molecular structures at a moving polymer/liquid interface by sum frequency generation (SFG) vibrational spectroscopy has been demonstrated. N-(2-Aminoethyl)-3-aminopropyltrimethoxysilane (AATM, NH2(CH2)2NH(CH2)3Si(OCH3)3) has been brought into contact with a deuterated poly(methyl methacrylate) (d-PMMA) film, and the interfacial silane structure has been monitored using SFG. Upon initial contact, the SFG spectra can be detected, but as time progresses, the spectral intensity changes and finally disappears. Additional experiments indicate that these silane molecules can diffuse into the polymer film and the detected SFG signals are actually from the moving polymer/silane interface. Our results show that the molecular order of the polymer/silane interface exists during the entire diffusion process and is lost when the silane molecules traverse through the thickness of the d-PMMA film. The loss of the SFG signal is due to the formation of a new disordered substrate/silane interface, which contributes no detectable SFG signal. The kinetics of the diffusion of the silane into the polymer have been deduced from the time-dependent SFG signals detected from the AATM molecules as they diffuse through polymer films of different thickness.     

Study of the dynamics of surface molecules by time-resolved sum-frequency generation spectroscopy

Sum-frequency generation (SFG) is a nonlinear laser-spectroscopy technique suitable for analysis of adsorbed molecules. The sub-monolayer sensitivity of SFG spectroscopy enables vibrational spectra to be obtained with high specificity for a variety of molecules on a range of surfaces, including metals, oxides, and semiconductors. The use of ultra-short laser pulses on time-scales of picoseconds also makes time-resolved measurements possible; this can reveal ultrafast transient changes in molecular arrangements. This article reviews recent time-resolved SFG spectroscopy studies revealing site-hopping of adsorbed CO on metal surfaces and the dynamics of energy relaxation at water/metal interfaces. Time-resolved sum frequency generation spectroscopy at surfaces with non-resonant laser pulse irradiation     

Molecular level structures of poly(n-alkyl methacrylate)s with different side chain lengths at the polymer/air and polymer/water interfaces

Sum frequency generation (SFG) vibrational spectroscopy has been successfully applied to study molecular structures of several poly(n-alkyl methacrylate)s (PAMAs) with different side chain lengths at the PAMA/air and PAMA/water interfaces. We have observed that the ester side chains from all PAMAs always dominate the interface, but the orientation information of the methyl end group on the side chains varies, depending on the length of the side chain. The contributions from methylene groups on the side chains have been evaluated, and the surface structures have been related to the surface tension of these polymers. Different water restructuring behaviors have been observed for different PAMAs. This phenomenon and its reversibility are strongly dependent on the glass transition temperature of each polymer, which is influenced by the side chain length. Detailed data fitting and analysis has been discussed.     

Preliminary Communication : Generation of high pretilt angles of nematic liquid crystal (5CB) on rubbed organic solvent soluble polyimide surfaces with helical backbone structure and trifluoromethyl moieties

High pretilt angles of nematic liquid crystals (NLC) have been successfully generated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. We have found that the pretilt angle of in 4-n-penty-4-cyanobiphenyl (5CB) on rubbed PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings is larger compared to that on rubbed PI surfaces with trifluoromethyl moieties attached to the polymer backbone. The observed pretilt angle of 5CB on unidirectionally rubbed PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings is about 15 degrees in the wide rubbing region. From these results, it is expected that the microscopic surface structure of the polymer strongly contributes to the pretilt angle generation of the LCs at the surface.     

Vibrational sum-frequency generation at protein modified air–water interfaces: Effects of molecular structure and surface charging

Protein and surfactant modified air–water interfaces are an important model system for colloid science as many applications for example aqueous foams in food products rely on our knowledge and ability to tune molecular structures at these interfaces. That is because interfaces are a fundamental building block in the hierarchical structure of foam, where in fact the molecular level can determine properties on larger length scales. For that reason it is of great importance to increase our ability to study air–water interfaces with molecular level probes and to obtain not only information on coverage but also direct information on interfacial composition, molecular order, orientations as well as information on the charged state of an interface. Vibrational sum-frequency generation (SFG) is a powerful tool that can help to address these issues and is inherently surface sensitive. In this contribution we will review recent developments in the use of SFG for studies of biomolecules at aqueous interfaces and discuss current issues with the interpretation of SFG spectra from electrified interfaces. In order to guide interpretations from interface spectroscopy we invoke the use of complementary methods such as ellipsometry and zetapotential measurements of bulk molecules.