Isotope-dilution ICP–MS for trace element determination and speciation: from a reference method to a routine method?

This critical review discusses the conditions under which inductively coupled plasma–isotope dilution mass spectrometry (ICP–IDMS) is suitable as a routine method for trace element and element-speciation analysis. It can, in general, be concluded that ICP–IDMS has high potential for routine analysis of trace elements if the accuracy of results is of predominant analytical importance. Hyphenated techniques with ICP–IDMS suffer both from lack of commercially available isotope-labeled spike compounds for species-specific isotope dilution and from the more complicated system set-up required for species-unspecific ICP–IDMS analysis. Coupling of gas or liquid chromatography with species-specific ICP–IDMS, however, enables validation of analytical methods involving species transformations which cannot easily be performed by other methods. The potential and limitations of ICP–IDMS are demonstrated by recently published results and by some unpublished investigations by our group. It has been shown that possible loss of silicon as volatile SiF₄ during decomposition of a sample by use of hydrofluoric acid has no effect on trace silicon determination if the isotope-dilution step occurs during digestion in a closed system. For powder samples, laser ablation ICP–IDMS can be applied with an accuracy comparable with that only available from matrix-matched standardization, whereas the accuracy of electrothermal vaporization ICP–IDMS was strongly dependent on the element determined. The significance of easy synthesis of isotope-labeled spike compounds for species-specific ICP–IDMS is demonstrated for monomethylmercury and Cr(VI). Isotope-exchange reactions between different element species can prevent the successful application of ICP–IDMS, as is shown for iodinated hydrocarbons. It is also shown for monomethylmercury that species transformations during sample-pretreatment steps can be followed by species-specific ICP–IDMS without loss of accuracy. A relatively simple and time-efficient procedure for determination of monomethylmercury in environmental and biological samples is discussed. The method, which entails a rapid microwave-assisted isotope dilution step and in-situ extraction of the derivatized species, has good potential for routine application in the future.     

Validation of a simplified field-adapted procedure for routine determinations of methyl mercury at trace levels in natural water samples using species-specific isotope dilution mass spectrometry

A field-adapted procedure based on species-specific isotope dilution (SSID) methodology for trace-level determinations of methyl mercury (CH₃Hg⁺) in mire, fresh and sea water samples was developed, validated and applied in a field study. In the field study, mire water samples were filtered, standardised volumetrically with isotopically enriched CH₃²⁰⁰Hg⁺, and frozen on dry ice. The samples were derivatised in the laboratory without further pre-treatment using sodium tetraethyl borate (NaB(C₂H₅)₄) and the ethylated methyl mercury was purge-trapped on Tenax columns. The analyte was thermo-desorbed onto a GC-ICP-MS system for analysis. Investigations preceding field application of the method showed that when using SSID, for all tested matrices, identical results were obtained between samples that were freeze-preserved or analysed unpreserved. For DOC-rich samples (mire water) additional experiments showed no difference in CH₃Hg⁺ concentration between samples that were derivatised without pre-treatment or after liquid extraction. Extractions of samples for matrix–analyte separation prior to derivatisation are therefore not necessary. No formation of CH₃Hg⁺ was observed during sample storage and treatment when spiking samples with ¹⁹⁸Hg²⁺. Total uncertainty budgets for the field application of the method showed that for analyte concentrations higher than 1.5 pg g^–1 (as Hg) the relative expanded uncertainty (REU) was approximately 5% and dominated by the uncertainty in the isotope standard concentration. Below 0.5 pg g^–1 (as Hg), the REU was >10% and dominated by variations in the field blank. The uncertainty of the method is sufficiently low to accurately determine CH₃Hg⁺ concentrations at trace levels. The detection limit was determined to be 4 fg g^–1 (as Hg) based on replicate analyses of laboratory blanks. The described procedure is reliable, considerably faster and simplified compared to non-SSID methods and thereby very suitable for routine applications of CH₃Hg⁺ speciation analysis in a wide range of water samples.     

In situ ethylation of organolead,organotin and organomercury species by bromomagnesium tetraethylborate prior to GC‐ICP‐MS analysis

An analytical method for simultaneous in situ ethylation, of organolead, organotin and organomercury compounds in aqueous samples was developed using a new derivatisation agent, bromomagnesium tetraethylborate (BrMgEt₄B). The determination of lead, tin and mercury compounds was done by species‐specific isotope dilution, derivatisation and GC–inductively coupled plasma MS (GC‐ICP‐MS) or by GC‐MS. The recovery and accuracy of the derivatisation were evaluated. The effect of pH and the relative quantity of derivatisation agent were studied.     

Simultaneous quantification of oleuropein and its metabolites in rat plasma by liquid chromatography electrospray ionization tandem mass spectrometry

Oleuropein (OE) is the cardinal bioactive compound derived from Olea europaea and possesses numerous beneficial properties for human health. However, despite the plethora of analytical methods that have studied the biological fate of olive oil‐derived bioactive compounds, no validated methodology has been published to date for the simultaneous determination of OE, along with all its major metabolites. In this study, a liquid chromatography‐electrospray ionization‐tandem mass spectrometry (LC‐ESI MS/MS) method has been developed and validated for the quantification of OE, simultaneously with its main metabolites hydroxytyrosol, 2‐(3,4‐dihydroxyphenyl)acetic acid, 4‐(2‐hydroxyethyl)‐2‐methoxy‐phenol or homovanillyl alcohol, 2‐(4‐hydroxy‐3‐methoxyphenyl)acetic acid or homovanillic acid, and elenolic acid in rat plasma matrix. Samples were analyzed by LC‐ESI MS/MS prior to and after enzymatic treatment. A solid‐phase extraction step with high mean recovery for all compounds was performed as sample pretreatment. Calibration curves were linear for all bioactive compounds over the range studied, while the method exhibited good accuracy, intra‐ and inter‐day precision. The limit of detection was in the picogram range (per milliliterof plasma) for HT and OE and in the nanogram range (per milliliter of plasma) for the other analytes, and the method was simple and rapid. The developed methodology was successfully applied for the simultaneous quantification of OE and its aforementioned metabolites in rat plasma samples, thus demonstrating its suitability for pharmacokinetics, as well as bioavailability and metabolism studies. Copyright © 2009 John Wiley & Sons, Ltd.     

Determination of Mercury in Urine and Seawater by Flow Injection Vapor Generation Isotope Dilution Inductively Coupled Plasma Mass Spectrometry

A simple and inexpensive laboratory-built vapor generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of mercury in urine and seawater samples. The applications of vapor generation ICP-MS alleviated the non-spectroscopic interferences and the sensitivity problem of mercury determination encountered when the conventional pneumatic nebulizer was used for sample introduction. The concentration of mercury was determined by isotope dilution method. The isotope ratio of mercury was calculated from the peak areas of each injection peak. The repeatability of the peak areas and isotope ratio determinations of seven consecutive injections of 1 ng mL^?1 Hg solution were 2.3% and 2.2%, respectively. This method has a detection limit of 0.07 ng mL^?1 for mercury. This method was applied to determine mercury in a CASS-3 nearshore seawater reference sample, NASS-4 open ocean seawater reference sample, NIST SRM 2670 freeze-dried urine reference sample and several urine and seawater samples collected from National Sun Yat-Sen University. The results for the reference samples agreed satisfactorily with the reference values. Results for other samples analyzed by the isotope dilution method and the method of standard additions agreed satisfactorily. Precision was better than 10% for most of the determinations.     

Rapid analysis of fluoxetine and its metabolite in plasma by LC-MS with column-switching approach

A rapid and sensitive method was developed for the simultaneous determination of fluoxetine and its primary metabolite, norfluoxetine, in plasma. It was based on a column-switching approach with a precolumn packed with large size particles coupled with a liquid chromatography–electrospray ionisation–mass spectrometry (LC-ESI-MS). After a simple centrifugation, plasma samples were directly injected onto the precolumn. The endogenous material was excluded thanks to a high flow rate while analytes were retained by hydrophobic interactions. Afterwards, the target compounds were eluted in back flush mode to an octadecyl analytical column and detected by ESI-MS. The overall analysis time per sample, from plasma sample preparation to data acquisition, was achieved in less than 4 min. Method performances were evaluated. The method showed good linearity in the range of 25–1000 ng mL^–1 with a determination coefficient higher than 0.99. Limits of quantification were estimated at 25 ng mL^–1 for fluoxetine and norfluoxetine. Moreover, method precision was better than 6% in the studied concentration range. These results demonstrated that the method could be used to quantify target compounds. Finally, the developed assay proved to be suitable for the simultaneous analysis of fluoxetine and its metabolite in real plasma samples.     

Determination of terbuthylazine and desethylterbuthylazine in human urine and hair samples by eletrospray ionization-liquid chromatography/triple quadrupole mass spectrometry

Terbuthylazine (TBA) is a widely applied herbicide and an environmental contaminant. Following its use, humans, such as agricultural workers and rural residents, may be exposed. An isotope-dilution liquid chromatography coupled to electrospray-tandem mass spectrometry method for the determination of TBA, and its metabolite desethylterbuthylazine (DET) in human urine and hair was developed and validated. Under the optimised conditions, analytes were extracted from urine using a solid phase cartridge or from hair by sonication in methanol. Analytes were separated using a C18 reversed-phase chromatographic column and quantified, after positive ionization using a heated electrospray source, by a triple quadrupole mass detector in the selected reaction monitoring mode. Validation showed linear dynamic ranges up to 100 μg/L or 5.00 ng/mg hair, inter- and intra-run precisions <7%, and accuracies within 12% of spiked concentrations. Limits of quantification were 0.25 μg/L in urine and 0.01 ng/mg hair for both TBA and DET. Matrix effect evaluation showed that the isotope dilution approach allowed for the control of bias sources. TBA and DET were determined in specimens of agriculture workers exposed to TBA using the validated method. Hair samples contained TBA levels in the low nanogram per milligram range, and urine samples contained DET levels in the low microgram per liter range. Conversely, TBA levels in urine samples and DET levels in hair samples were always below the limit of quantification.     

Evaluation of matrix effects in the analysis of volatile organic compounds in whole blood with solid‐phase microextraction

The complexity and matrix variability of biological samples requires an accurate evaluation of matrix effects. The dilution of the biological sample is the simplest way to reduce or avoid the matrix effect. In the present study, a set of volatile organic compounds with different volatilities was used to assess the effect of the dilution of blood samples on the extraction efficiency by headspace solid‐phase microextraction. It was found that there was a significant matrix effect but that this effect differs significantly depending on the volatility of the compound. A 1:2 (blood/water) dilution was enough to allow quantitative recoveries of those compounds with boiling points <100°C. For compounds with boiling points between 100 and 150°C, the matrix effect was stronger and a 1:5 dilution was required. The dilution of blood samples proved to be inefficient for quantitative recovery of compounds with boiling points >150°C. A 1:5 dilution of the sample allowed detection limits in the range of nanogram per liter to be obtained. This was sufficient to detect the main volatile compounds present in blood and contamination after exposure.     

Determination of silver in sea water by coprecipitation with cobalt pyrrolidinedithiocarbamate and Zeeman graphite-furnace atomic absorption spectrometry

A preconcentration technique is described for silver, which allows the precise and accurate determination of silver in sea water at nanogram per liter levels. Silver is co-precipitated with cobalt(II) pyrrolidinedithiocarbamate from 200-ml samples. The precipitate is dissolved in concentrated nitric acid and silver is quantified by Zeeman graphite-furnace atomic absorption spectrometry, with acid phosphate matrix modification. The detection limit is 0.1 ng l^?. The method is simple and rapid, and also allows the simultaneous extraction of lead, copper, cadmium, and nickel.     

Simultaneous determination of mono-, di- and tributyltin in environmental samples using isotope dilution gas chromatography mass spectrometry

The development of a rapid, precise and accurate speciation method for the simultaneous determination of mono-, di- and tributyltin in environmental samples is described. The method is based on using isotope dilution gas chromatography/mass spectrometry (GC/MS) with electron ionization, a widely used technique in routine testing laboratories. A mixed spike containing (119)Sn-enriched monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT) was used for the isotope dilution of the samples. Five molecular ions were monitored for each analyte, corresponding to the (116)Sn, (117)Sn, (118)Sn, (119)Sn and (120)Sn isotopes. The detection at masses corresponding to (116)Sn and (117)Sn were used to correct for m + 1 and m + 2 contributions of (13)C from the organic groups attached to the tin atom on the (118)Sn, (119)Sn and (120)Sn masses with simple mathematical equations and the concentrations of the butyltin compounds were calculated based on the corrected (118)Sn/(119)Sn and (120)Sn/(119)Sn isotope ratios. The (119)Sn-enriched multispecies spike was applied with satisfactory results to the simultaneous determination of MBT, DBT and TBT in three certified reference materials: two sediments, PACS-2 and BCR 646, and the mussel tissue CRM 477. The method was compared with a previously published GC/inductively coupled plasma MS isotope dilution procedure, developed in our laboratory, by injecting the same samples into both instruments. Comparable analytical results in terms of precision and accuracy are demonstrated for both atomic and molecular mass spectrometric detectors. Thus, reliable quantitative organotin speciation analysis can be achieved using the more widespread and inexpensive GC/MS instrument.     

Direct determination of mercury in cosmetic samples by isotope dilution inductively coupled plasma mass spectrometry after dissolution with formic acid

A new method was proposed for the accurate determination of mercury in cosmetic samples based on isotopic dilution (ID)-photochemical vapor generation (PVG)-inductively coupled plasma mass spectrometry (ICP MS) measurement. Cosmetic samples were directly dissolved in formic acid solution and subsequently subjected to PVG for the reduction of mercury into vapor species following by ICP MS detection. Therefore, the risks of analyte contamination and loss were avoided. Highly enriched ²⁰¹Hg isotopic spike is added to cosmetics and the isotope ratios of ²⁰¹Hg/²⁰²Hg were measured for the quantitation of mercury. With ID calibration, the influences originating from sample matrixes for the determination of mercury in cosmetic samples have been efficiently eliminated. The effects of several experimental parameters, such as the concentration of the formic acid, and the flow rates of carrier gas and sample were investigated. The method provided good reproducibility and the detection limits were found to be 0.6 pg mL⁻¹. Finally, the developed method was successfully applied for the determination of mercury in six cosmetic samples and a spike test was performed to verify the accuracy of the method.     

Determination of Hg(II) in Environmental Water Samples Using DLLME Method Prior to GC-FID

Mercury exists in two forms in environment, inorganic salts and organic compounds. Determination of mercury is very important, due to its health effects. In the present research, diphenylation of mercury using phenylboronic acid as a derivatization reagent was used for the determination of Hg(II) in real water samples. A simple, rapid and cheap method named dispersive liquid–liquid microextraction was used for the extraction of analyte under the following conditions: extraction solvent 16 μL of carbon tetrachloride, disperser solvent 1 mL of ethanol and sample volume 5 mL. Under the optimal conditions, the enrichment factor for diphenylmercury was 931 and the limit of detection calculated on the basis of five replicates was 0.004 μg mL^?1. The repeatability of the method expresses as relative standard deviation was 5.1 (n = 6). The linear range was between 0.01 and 10 μg mL^?1. The performance of the proposed technique was evaluated for the determination of mercury in different environmental water samples.     

Pre-column derivatization of rofecoxib for determination in serum by HPLC

An HPLC method for determination of rofecoxib in human serum is presented. The method is based on pre-column derivatization of analyte to a phenanthrene derivative of the drug. Rofecoxib and the internal standard were extracted from serum using liquid–liquid extraction. Upon exposure to UV light, the drug was found to undergo a photocyclization reaction, giving a species with high absorbance. Validation of the method has been studied in the concentration range 10–500 ng ml^–1.     

Continuous-flow potentiometric determination of creatinine in urine with a picrate ion-selective electrode

A completely automated potentiometric method for the determination of creatinine in urine is described. Creatinine reacts with picrate in alkaline media (Jaffé reaction) in a flow system, and the decrease in picrate activity is continuously monitored with a picrateselective flow-through electrode. Creatinine in urine, in the range 0.5–3 g/liter, was determined in a sample volume of 0.15 ml, with a relative standard deviation of about 1%. Forty samples per hour can be analyzed without previous dilution or pretreatment. Recovery of creatinine added to urine samples ranged from 90 to 111% with an average of 96.7%. The method compares favorably with a photometric method. The proposed automated method is suitable for routine clinical measurements and screening tests.     

Determination of Hg(II) in Environmental Water Samples Using DLLME Method Prior to GC-FID

Mercury exists in two forms in environment, inorganic salts and organic compounds. Determination of mercury is very important, due to its health effects. In the present research, diphenylation of mercury using phenylboronic acid as a derivatization reagent was used for the determination of Hg(II) in real water samples. A simple, rapid and cheap method named dispersive liquid–liquid microextraction was used for the extraction of analyte under the following conditions: extraction solvent 16 μL of carbon tetrachloride, disperser solvent 1 mL of ethanol and sample volume 5 mL. Under the optimal conditions, the enrichment factor for diphenylmercury was 931 and the limit of detection calculated on the basis of five replicates was 0.004 μg mL⁻¹. The repeatability of the method expresses as relative standard deviation was 5.1 (n = 6). The linear range was between 0.01 and 10 μg mL⁻¹. The performance of the proposed technique was evaluated for the determination of mercury in different environmental water samples.

     

Isotope dilution analysis mass spectrometry for the routine measurement of butyltin compounds in marine environmental and biological samples

The highly qualified primary method of species-specific isotope dilution analysis has been employed in this work to evaluate for the first time the levels of butyltin compounds in the estuary of the river Eo (Northwest Spain) where there is, since many years, a high oyster farming activity. A spike solution containing mono-, di- and tributyltin enriched in ¹¹⁹Sn allowed the simultaneous determination of the three compounds in different marine environmental and biological samples collected in this area (seawater samples, sediments and biological tissues of four different marine species). The results obtained in this work showed toxic TBT levels for many marine species in 45% of the seawater samples analyzed whereas significant organotin concentrations were found to be obtained only in one of the sediments analyzed. On the other hand, TBT levels ranging from 20 to almost 200 ng g^− 1 (dry weight) were obtained in the different biological tissues analyzed demonstrating the bioaccumulation of organotin compounds in certain marine species.     

Rapid screening of selective serotonin re-uptake inhibitors in urine samples using solid-phase microextraction gas chromatography–mass spectrometry

In this paper a solid-phase microextraction–gas chromatography–mass spectrometry (SPME–GC–MS) method is proposed for a rapid analysis of some frequently prescribed selective serotonin re-uptake inhibitors (SSRI)—venlafaxine, fluvoxamine, mirtazapine, fluoxetine, citalopram, and sertraline—in urine samples. The SPME-based method enables simultaneous determination of the target SSRI after simple in-situ derivatization of some of the target compounds. Calibration curves in water and in urine were validated and statistically compared. This revealed the absence of matrix effect and, in consequence, the possibility of quantifying SSRI in urine samples by external water calibration. Intra-day and inter-day precision was satisfactory for all the target compounds (relative standard deviation, RSD, <14%) and the detection limits achieved were <0.4 ng mL^–1 urine. The time required for the SPME step and for GC analysis (30 min each) enables high throughput. The method was applied to real urine samples from different patients being treated with some of these pharmaceuticals. Some SSRI metabolites were also detected and tentatively identified.     

Optimization of simultaneous derivatization and extraction of aliphatic amines in water samples with dispersive liquid-liquid microextraction followed by HPLC

Dispersive liquid-liquid microextraction based on solidification of floating organic droplet (DLLME-SFO) with simultaneous derivatization followed by high-performance liquid chromatography-diode array detection (HPLC-DAD) was applied for preconcentration and determination of primary and secondary aliphatic amines in environmental water samples. A ternary mixture consisting of a disperser, an extractant and a derivatization reagent was used for the simultaneous derivatization and extraction of aliphatic amines in different water samples. The effects of various experimental parameters on derivatization and extraction efficiency were studied simultaneously using experimental design. A Plackett-Burman design was performed for screening of variables in order to determine the significant variables affecting the extraction efficiency. Then, the significant factors were optimized by using a Box-Behnken design (BBD) and the response surface equations were derived. Under optimal conditions, the preconcentration factors were between 210 and 290. The limit of detections (LODs) ranged from 0.005 to 0.02 μg/L and dynamic linear ranges (DLRs) of 0.05-500 and 0.1-500 μg/L were obtained for most of analytes. The performance of the method was evaluated for extraction and determination of primary and secondary aliphatic amines in environmental water samples in micrograms per liter and satisfactory results were obtained (RSDs <12.5%).     

Polarographic behaviour and determination of paracetamol and salicylamide after treatment with nitrous acid

A polarographic procedure is described for the determination of paracetamol (acetaminophen) and salicylamide after treatment with nitrous acid. The different experimental parameters affecting the derivatization process and the polarographic analysis were studied. The derivatization products were found to be reduced at the dropping mercury electrode over the whole pH range in Britton-Robinson buffers. At pH 7.0, well defined diffusion-controlled cathodic waves were produced for both compounds. Plots of limiting current vs. concentration were linear over the ranges 0.05–0.75 and 0.25–1.5mM for paracetamol and salicylamide, respectively, in the d.c. mode, with minimum detectability of 2.5 × 10^–6 and 1.25 × 10^–5 M, respectively. The procedure was applied to the analysis of some pharmaceutical dosage forms and the results were in good agreement with those obtained by official and compendial methods.     

Speciation of Mercury in Terrestrial Plants Using Vapor Generation and Liquid Chromatography–Inductively Coupled Plasma Mass Spectrometry

A sensitive method for mercury speciation in biological samples is reported. A simple vapor generation apparatus was coupled to liquid chromatography and inductively coupled plasma–mass spectrometry (ICP–MS) to achieve a substantial increase in sensitivity. Mercury(II) and methylmercury were separated by reversed-phase chromatography as thiolate compounds with 2-mercaptoethanol. A short reverse phase column with an octylated stationary phase (75 × 4 millimeters) was used with a mobile phase containing 0.02 mole per liter ammonium acetate, 0.2 percent (v/v) 2-mercaptoethanol, and 1 percent methanol. The effluent was mixed with hydrochloric acid (0.06 mole per liter) containing platinum (40 micrograms per liter) as the internal standard and bismuth (30 micrograms per liter) as a modifying agent followed by sodium borohydride (0.016 mole per liter). The generated volatile species were introduced into the ICP–MS by conventional solution nebulization. In addition to the sensitivity enhancement induced by vapor generation, the addition of bismuth further increased the methylmercury signal with a reduced increase in the mercury(II) signal. As a result, comparable but unequal signals were achieved: the mercury(II) signal was approximately 1.6-fold higher than the methylmercury signal. Extraction with a hydrochloric acid-2-mercaptoethanol solution was used for sample preparation. The accuracy of determination was verified using two standard reference materials and an interlaboratory reference material based on barley grown hydroponically in mercury-contaminated solution. The method was employed for mercury speciation of plant samples from a polluted region.