Development of liquid chromatography atmospheric pressure chemical ionization tandem mass spectrometry for analysis of halogenated flame retardants in wastewater

Until recently, atmospheric pressure photoionization (APPI) has typically been used for the determination of non-polar halogenated flame retardants (HFRs) by liquid chromatography (LC) tandem mass spectrometry. In this study, we demonstrated the feasibility of utilizing liquid chromatography atmospheric pressure chemical ionization (APCI) tandem mass spectrometry (LC-APCI-MS/MS) for analysis of 38 HFRs. This developed method offered three advantages: simplicity, rapidity, and high sensitivity. Compared with APPI, APCI does not require a UV lamp and a dopant reagent to assist atmospheric pressure ionization. All the isomers and the isobaric compounds were well resolved within 14-min LC separation time. Excellent instrument detection limits (6.1 pg on average with 2.0 μL injection) were observed. The APCI mechanism was also investigated. The method developed has been applied to the screening of wastewater samples for screening purpose, with concentrations determined by LC-APCI-MS/MS agreeing with data obtained via gas chromatography high resolution mass spectrometry.

The Ionization Mechanisms in Direct and Dopant-Assisted Atmospheric Pressure Photoionization and Atmospheric Pressure Laser Ionization

A novel, gas-tight API interface for gas chromatography–mass spectrometry was used to study the ionization mechanism in direct and dopant-assisted atmospheric pressure photoionization (APPI) and atmospheric pressure laser ionization (APLI). Eight analytes (ethylbenzene, bromobenzene, naphthalene, anthracene, benzaldehyde, pyridine, quinolone, and acridine) with varying ionization energies (IEs) and proton affinities (PAs), and four common APPI dopants (toluene, acetone, anisole, and chlorobenzene) were chosen. All the studied compounds were ionized by direct APPI, forming mainly molecular ions. Addition of dopants suppressed the signal of the analytes with IEs above the IE of the dopant. For compounds with suitable IEs or Pas, the dopants increased the ionization efficiency as the analytes could be ionized through dopant-mediated gas-phase reactions, such as charge exchange, proton transfer, and other rather unexpected reactions, such as formation of [M?+?77]⁺ in the presence of chlorobenzene. Experiments with deuterated toluene as the dopant verified that in case of proton transfer, the proton originated from the dopant instead of proton-bound solvent clusters, as in conventional open or non-tight APPI sources. In direct APLI using a 266 nm laser, a narrower range of compounds was ionized than in direct APPI, because of exceedingly high IEs or unfavorable two-photon absorption cross-sections. Introduction of dopants in the APLI system changed the ionization mechanism to similar dopant-mediated gas-phase reactions with the dopant as in APPI, which produced mainly ions of the same form as in APPI, and ionized a wider range of analytes than direct APLI. Graphical Abstract

?     

Atmospheric Pressure Photo Ionization Hydrogen/Deuterium Exchange Mass Spectrometry—a Method to Differentiate Isomers by Mass Spectrometry

In this report, a method for in-source hydrogen/deuterium (H/D) exchange at atmospheric pressure is reported. The method was named atmospheric pressure photo ionization hydrogen/deuterium exchange mass spectrometry (APPI HDX MS). H/D exchange was performed by mixing samples dissolved in toluene with CH₃OD solvent and analyzing the mixture using atmospheric pressure photo ionization mass spectrometry (APPI-MS). The APPI HDX spectra obtained with contact times between the analyte solution and methanol-OD (CH₃OD) of?<?0.5 s or 1 h showed the same pattern of H/D exchange. Therefore, it was concluded that APPI HDX occurred in the source but not in the solution. The proposed method does not require a specific type of mass spectrometer and can be performed at atmospheric pressure. H/D exchange can be performed in any laboratory with a mass spectrometer and a commercial APPI source. Using this method, multiple H/D exchanges of aromatic hydrogen and/or H/D exchange of active hydrogen were observed. These results demonstrated that H/D exchange can be used to distinguish between isomers containing primary, secondary, and tertiary amines, as well as pyridine and pyrrole functional groups.

Microwave assisted extraction for mercury speciation analysis

The application of microwave-assisted extraction (MAE) to the work-up of environmental and biological samples in the study of mercury speciation analysis has increased in recent years and is now increasingly accepted as a standard approach. The review provides a brief theoretical background of microwave heating and the basic principles of microwave energy used for extraction. The advantages and disadvantages of (a) MAE techniques, (b) the influence of the main parameters affecting the extraction, (c) statistical optimization approaches, and (d) strategies for method validation also are highlighted. Recent applications of MAE to mercury species analyses in biological samples, soils, sediments, and crude oil samples are surveyed and critically reviewed. In addition, comparisons of its use with other well-established extraction procedures are discussed.

Magnetic molecular imprint-based extraction of sulfonylurea herbicides and their determination by capillary liquid chromatography

We have developed a simple method for the extraction of sulfonylurea herbicides (SUHs) from environmental water samples. It is based on a magnetic molecular imprint (MMIP) as a sorbent. The MMIP was prepared using metsulfuron-methyl as the template molecule, methacrylic acid as the functional monomer, trimethylolpropane trimethacrylate as the cross-linking agent, and magnetite as the magnetic component. Extraction can be carried out by blending and stirring water sample, extraction solvent and MMIP. Once the extraction is completed, the MMIP containing the SUHs can be separated from the sample matrix with a magnet. The SUHs desorbed from the polymers were then quantified by capillary liquid chromatography with diode array detection. The limits of quantification are in the range of 0.08 to 0.1 ng?mL^?1. Repeatabilities of peak areas and retention times range from 2.9 % to 4.0 % and from 0.1 % to 0.3 %, respectively. The method was successfully applied to the determination of the SUHs bensulfuron-methyl, metsulfuronmethyl, pyrazosulfuron-methyl, thifensulfuron-methyl, and triasulfuron in waste water samples. Recoveries range from 94.3 % to 102.3 %.

Direct probe atmospheric pressure photoionization/atmospheric pressure chemical ionization high-resolution mass spectrometry for fast screening of flame retardants and plasticizers in products and waste

In this study, we develop fast screening methods for flame retardants and plasticizers in products and waste based on direct probe (DP) atmospheric pressure photoionization (APPI) and atmospheric pressure chemical ionization (APCI) coupled to a high-resolution (HR) time-of-flight mass spectrometer. DP-APPI is reported for the first time in this study, and DP-APCI that has been scarcely exploited is optimized for comparison. DP-APPI was more selective than DP-APCI and also more sensitive for the most hydrophobic compounds. No sample treatment was necessary, and only a minimal amount of sample (few milligrams) was used for analysis that was performed within a few minutes. Both methods were applied to the analysis of plastic products, electronic waste, and car interiors. Polybrominated diphenylethers, new brominated flame retardants, and organophosphorus flame retardants were present in most of the samples. The combination of DP with HR mass spectra and data processing based on mass accuracy and isotopic patterns allowed the unambiguous identification of chemicals at low levels of about 0.025 % (w/w). Under untargeted screening, resorcinol bis(biphenylphosphate) and bisphenol A bis(bisphenylphosphate) were identified in many of the consumer products of which literature data are still very limited.

Flow injection of liquid samples to a mass spectrometer with ionization under vacuum conditions: a combined ion source for single-photon and electron impact ionization

Electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI), and atmospheric pressure photo-ionization (APPI) are the most important techniques for the ionization of liquid samples. However, working under atmospheric pressure conditions, all these techniques involve some chemical rather than purely physical processes, and therefore, side reactions often yield to matrix-dependent ionization efficiencies. Here, a system is presented that combines both soft single-photon ionization (SPI) and hard 70 eV electron impact ionization (EI) of dissolved compounds under vacuum conditions. A quadrupole mass spectrometer was modified to enable direct EI, a technique developed by Cappiello et al. to obtain library-searchable EI mass spectra as well as soft SPI mass spectra of sample solutions. An electron beam-pumped rare gas excimer lamp working at 126 nm was used as well as a focusable vacuum UV light source for single-photon ionization. Both techniques, EI and SPI, were applied successfully for flow injection experiments providing library-matchable EI fragment mass spectra and soft SPI mass spectra, showing dominant signals for the molecular ion. Four model compounds were analyzed: hexadecane, propofol, chlorpropham, and eugenol, with detection limits in the picomolar range. This novel combination of EI and SPI promises great analytical benefits, thanks to the possibility of combining database alignment for EI data and molecular mass information provided by SPI. Possible applications for the presented ionization technology system are a matrix-effect-free detection and a rapid screening of different complex mixtures without time-consuming sample preparation or separation techniques (e.g., for analysis of reaction solutions in combinatorial chemistry) or a switchable hard (EI) and soft (SPI) MS method as detection step for liquid chromatography.

Pressurised hot water extraction in continuous flow mode for thermolabile compounds: extraction of polyphenols in red onions

Extraction and analysis of labile compounds in complex sample matrices, such as plants, is often a big analytical challenge. In this work, the use of a “green and clean” pressurised hot water extraction (PHWE) approach performed in continuous flow mode is explored. Experimental data for extraction and degradation kinetics of selected compounds were utilised to develop a continuous flow extraction (CFE) method targeting thermolabile polyphenols in red onions, with detection by high-performance liquid chromatography (HPLC)–diode array detection (DAD)–mass spectrometry (MS). Water containing ethanol and formic acid was used as extraction solvent. Method performance was focused on extraction yield with minimal analyte degradation. By adjusting the flow rate of the extraction solvent, degradation effects were minimised, and complete extraction could be achieved within 60 min. The CFE extraction yields of the polyphenols investigated were 80–90 % of the theoretically calculated quantitative yields and were significantly higher than the yields obtained by conventional methanol extraction and static batch extraction (70–79 and 58–67 % of the theoretical yields, respectively). The precision of the developed method was lower than 8 % expressed as relative standard deviation.

Single-walled carbon nanohorns immobilized on a microporous hollow polypropylene fiber as a sorbent for the extraction of volatile organic compounds from water samples

We have evaluated the behavior of single-walled carbon nanohorns as a sorbent for headspace and direct immersion (micro)solid phase extraction using volatile organic compounds (VOCs) as model analytes. The conical carbon nanohorns were first oxidized in order to increase their solubility in water and organic solvents. A microporous hollow polypropylene fiber served as a mechanical support that provides a high surface area for nanoparticle retention. The extraction unit was directly placed in the liquid sample or the headspace of an aqueous standard or a water sample to extract and preconcentrate the VOCs. The variables affecting extraction have been optimized. The VOCs were then identified and quantified by GC/MS. We conclude that direct immersion of the fiber is the most adequate method for the extraction of VOCs from both liquid samples and headspace. Detection limits range from 3.5 to 4.3 ng L^?1 (excepted for toluene with 25 ng L^?1), and the precision (expressed as relative standard deviation) is between 3.9 and 9.6 %. The method was applied to the determination of toluene, ethylbenzene, various xylene isomers and styrene in bottled, river and tap waters, and the respective average recoveries of spiked samples are 95.6, 98.2 and 86.0 %.

Novel method for in-situ surfactant-based solid-phase extraction: application to the determination of Co(II) and Ni(II) in aqueous samples

We report on a completely new kind of solid phase extraction which we term in-situ surfactant-based solid-phase extraction (ISS-SPE). It represents a simple and rapid method for extraction from aqueous samples and preconcentration of compounds containing hydrophobic (alkyl) groups. A cationic surfactant containing alkyl chain is dissolved in the aqueous sample. Following the addition of hexafluorophosphate (HFP; an ion-pairing anion), solutions turn cloudy due to the interaction between the surfactant and the HFP ion. This is due to the formation of fine solid particles composed of the HFP salt of the cationic surfactant. The alkyl groups of the surfactant in the solid particles strongly interact with hydrophobic groups of analytes and become bound. The solid particles are centrifuged, and the sedimented particles can be either dissolved in an appropriate organic solvent, or leached with a solvent to recover the absorbed analyte(s). The method presented here has distinct advantages in that the extraction times are short and recoveries are high, probably a result of the formation of very fine particles of large specific surface, and of their good dispersion in the sample solution. The performance of ISS-SPE was demonstrated by extracting chelates of Co(II) and Ni(II) from water samples. Under the optimized conditions, the preconcentration factors are 51 and 45, respectively, and the detection limits are 0.9 and 0.6???g?L^?1. The method was validated by the analysis of a certified reference material and by comparing results with those obtained by electrothermal AAS.

On-line solid-phase microextraction of triclosan, bisphenol A, chlorophenols, and selected pharmaceuticals in environmental water samples by high-performance liquid chromatography–ultraviolet detection

A method using on-line solid-phase microextraction (SPME) on a carbowax-templated fiber followed by liquid chromatography (LC) with ultraviolet (UV) detection was developed for the determination of triclosan in environmental water samples. Along with triclosan, other selected phenolic compounds, bisphenol A, and acidic pharmaceuticals were studied. Previous SPME/LC or stir-bar sorptive extraction/LC-UV for polar analytes showed lack of sensitivity. In this study, the calculated octanol–water distribution coefficient (log D) values of the target analytes at different pH values were used to estimate polarity of the analytes. The lack of sensitivity observed in earlier studies is identified as a lack of desorption by strong polar–polar interactions between analyte and solid-phase. Calculated log D values were useful to understand or predict the interaction between analyte and solid phase. Under the optimized conditions, the method detection limit of selected analytes by using on-line SPME-LC-UV method ranged from 5 to 33 ng?L^?1, except for very polar 3-chlorophenol and 2,4-dichlorophenol which was obscured in wastewater samples by an interfering substance. This level of detection represented a remarkable improvement over the conventional existing methods. The on-line SPME-LC-UV method, which did not require derivatization of analytes, was applied to the determination of TCS including phenolic compounds and acidic pharmaceuticals in tap water and river water and municipal wastewater samples.

Simultaneous sampling of volatile and non-volatile analytes in beer for fast fingerprinting by extractive electrospray ionization mass spectrometry

By gently bubbling nitrogen gas through beer, an effervescent beverage, both volatile and non-volatile compounds can be simultaneously sampled in the form of aerosol. This allows for fast (within seconds) fingerprinting by extractive electrospray ionization mass spectrometry (EESI-MS) in both negative and positive ion mode, without the need for any sample pre-treatment such as degassing and dilution. Trace analytes such as volatile esters (e.g., ethyl acetate and isoamyl acetate), free fatty acids (e.g., caproic acid, caprylic acid, and capric acid), semi/non-volatile organic/inorganic acids (e.g., lactic acid), and various amino acids, commonly present in beer at the low parts per million or at sub-ppm levels, were detected and identified based on tandem MS data. Furthermore, the appearance of solvent cluster ions in the mass spectra gives insight into the sampling and ionization mechanisms: aerosol droplets containing semi/non-volatile substances are thought to be generated via bubble bursting at the surface of the liquid; these neutral aerosol droplets then collide with the charged primary electrospray ionization droplets, followed by analyte extraction, desolvation, ionization, and MS detection. With principal component analysis, several beer samples were successfully differentiated. Therefore, the present study successfully extends the applicability of EESI-MS to the direct analysis of complex liquid samples with high gas content.

Functionalization of cross linked chitosan with 2-aminopyridine-3-carboxylic acid for solid phase extraction of cadmium and zinc ions and their determination by atomic absorption spectrometry

We have developed a new method for solid phase extraction (SPE) and preconcentration of trace amounts of cadmium and zinc using cross linked chitosan that was functionalized with 2-aminopyridine-3-carboxy acid. Analytical parameters, sample pH, effect of flow rate, sample volume, and concentration of eluent on column SPE were investigated. The effect of matrix ions on the recovery of cadmium and zinc has been investigated and were found not to interfere with preconcentration. Under the optimum experimental conditions, the preconcentration factors for Cd(II) and Zn(II) were found to be 90. The two elements were quantified via atomic absorption spectrometry. The detection limits for cadmium and zinc are 21 and 65?ng?L^?1, respectively. The method was evaluated by analyzing a certified reference material (NIST 1643e; water) and has been successfully applied to the analysis of cadmium and zinc in environmental water samples.

Solid-phase extraction of lead(II) ions using multiwalled carbon nanotubes grafted with tris(2-aminoethyl)amine

Multiwalled carbon nanotubes were grafted with tris(2-aminoethyl)amine (MWCNTs-TAA) and employed for solid phase extraction and preconcentration of trace lead ions prior to its determination by inductively coupled plasma optical emission spectrometry. The material was characterized by FT-IR and Raman spectroscopy, thermosgravimetric and elemental analysis. The effects of pH value, shaking time, sample volume, elution conditions and potentially interfering ions were investigated. Under the optimum conditions, the maximum adsorption capacity is 38?mg?g^?1 of Pb(II), the detection limit is 0.32?ng?mL^?1, the enrichment factor is 60, and the relative standard deviation is 3.5% (n?=?6). The method has been applied to the preconcentration of trace amounts of Pb(II) in environmental water samples with satisfactory results.

In-situ ionic liquid-based microwave-assisted dispersive liquid–liquid microextraction of triazine herbicides

We report on the determination of the triazine herbicides ametryne, prometryne, terbuthylazine and terbutryn in water samples. The herbicides are extracted by in-situ ionic liquid-based microwave-assisted dispersive liquid-liquid microextraction and then determined by high-performance liquid chromatography. This is a new method for extraction that has the advantages of requiring less volume of ionic liquid (IL) than other methods and at the same time is quite fast. The type and volume of IL, the type and volume of disperser, irradiation temperature, extraction time and salt concentration were optimized. Figures of merit include linear regression coefficients between 0.9992 and 0.9995, acceptable recoveries (88.4–114?%), relative standard deviations of 1.6–6.2?%, and limits of detection between 0.52 and 1.3?μg?L^?1.

Fragment-imprinted microspheres for the extraction of sulfonamides

Fragment-imprinted microspheres (FIMs) were synthesized by suspension polymerization of 4-sulfa-6-chloropyrimidine (the template), methacrylic acid and styrene (the mixed functional monomers), divinylbenzene (the crosslinker), and azobisisobutyronitrile (the initiator). The optimum conditions were obtained by an orthogonal experiment. After removal of the templates, the microspheres serve as a material to fairly specifically bind sulfonamides, the absorption capacity being 6.32 mg g^–1, whereas the absorption by non-imprinted microspheres is 1.68 mg g^?1. A method was worked out for the simultaneous determination of five sulfonamides by solid phase extraction (using the FIMs) coupled to HPLC, and applied to analyze milk samples. The recoveries are within 87.6 and 96.5 %, with relative standard deviations between 1.25 and 2.89 %.

Development of a microwave-assisted-extraction-based method for the determination of aflatoxins B1, G1, B2, and G2 in grains and grain products

This article describes the use of microwave-assisted extraction (MAE) as a pretreatment technique for the determination of aflatoxins B₁, G₁, B₂, and G₂ in grains and grain products. The optimal operation parameters, including extraction solvent, temperature, and time, were identified to be acetonitrile as the extraction solvent at 80 °C with 15 min of MAE. The extracts were cleaned up using solid-phase extraction followed by derivatization with trifluoroacetic acid and were determined by liquid chromatography–fluorescence detection. A Sep-Pak cartridge was chosen over Oasis HLB and Bond Elut cartridges. By the use of aflatoxin M₁ as an internal standard, relative recoveries of the aflatoxins ranged from 90.7 to 105.7 % for corn and from 88.1 to 103.4 % for wheat, with relative standard deviations between 2.5 and 8.7 %. A total of 36 samples from local markets were analyzed, and aflatoxin B₁ was found to be the predominant toxin, with concentrations ranging from 0.42 to 3.41 μg/kg.

Multiwalled carbon nanotubes modified with 2-aminobenzothiazole modified for uniquely selective solid-phase extraction and determination of Pb(II) ion in water samples

A solid phase extraction method is presented for the selective preconcentration and/or separation of trace Pb(II) on multiwalled carbon nanotubes modified with 2-aminobenzothiazole. Inductively coupled plasma optical emission spectrometry was used for detection. The effects of pH, shaking time, sample flow rate and volume, elution condition and interfering ions were examined using batch and column procedures. An enrichment factor of 100 was accomplished. Common other ions do not interfere in both the separation and determination. The maximum adsorption capacity of the sorbent at optimum conditions is 60.3?mg?g^?1 of Pb(II), the detection limit (3??) is 0.27?ng?mL^?1, and the relative standard deviation is 1.6% (n?=?8). The method was validated using a certified reference material, and has been applied to the determination of trace Pb(II) in water samples with satisfactory results.

Micro-scale quantitation of ten phthalate esters in water samples and cosmetics using capillary liquid chromatography coupled to UV detection: effective strategies to reduce the production of organic waste

We have extracted ten phthalate esters (C1 to C8) using six different micro-scale methods for extraction, and then separated them by capillary liquid chromatography coupled to UV detection. The methods included liquid-liquid extraction, ultrasonic-assisted extraction, microwave-assisted extraction, dispersive liquid-liquidmicroextraction, dispersive liquid-liquid microextraction solidification of floating organic droplets, and cloud point extraction. The linear range of the analytes is from 0.5 to 50 μg mL^?1, and the detection limits range from 0.02 to ~0.17 μg mL^?1. The precision and accuracy of all intra- and inter-day analyses are <5.5%. We find that dispersive liquid-liquid microextraction solidification of floating organic droplet (DLLME-SFO) is the best method for quantification of most phthalate esters in water samples and cosmetics because of its low limit of detection and high extraction efficiencies.

Multi-residue analysis of emerging pollutants in sediment using QuEChERS-based extraction followed by LC-MS/MS analysis

Emerging contaminants are suspected to cause adverse effects in humans and wildlife. Aquatic ecosystems are continuously contaminated by agricultural and industrial sources. To establish a causality relationship between the occurrence of contaminants in the environment and disease, experiments including all environmental matrices must be performed. Consequently, the current analytical tools must be improved. A new multi-residue method for analysing 15 emerging pollutants in sediments based on the Quick, Easy, Cheap, Effective, Rugged and Safe approach is reported. The development of such a multirisque, inter-family method for sediment including pharmaceuticals, pesticides, personal care products and plasticizers is reported for the first time. The procedure involves salting-out liquid–liquid extraction using acetonitrile and clean-up with dispersive solid phase extraction, followed by liquid chromatography coupled with tandem mass spectrometry. The validated analytical procedure exhibited recoveries between 40 and 98 % for every target compound. This methodology facilitated the determination of pollutant contents at nanogram-per-gram concentrations.