乳液分散法制备高分散纳米锡/介孔碳复合材料及其电化学性能

以间苯二酚和糠醛聚合而成的可溶性树脂为碳源,SnCl2为锡源,表面活性剂F127为模板剂,通过乳液分散法将锡源原位复合嵌入于介孔碳材料中,制备了纳米锡基材料高度分散于介孔碳中的复合材料。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、N2吸脱附(BET)、循环伏安(CV)等对材料的微观结构和电化学性能进行了表征。结果显示锡基材料在介孔碳中较为密集,分布均匀,粒径小于5 nm。介孔碳丰富的孔道结构有效限制和缓解了锡基材料的生长、团聚和体积膨胀,同时高比表面积增加了电解液与锡基活性材料的接触,提供了更多的反应活性点,从而获得了更高的电化学活性。充放电测试结果显示,700℃热处理后,锡/介孔碳纳米复合材料经过50次循环后实际放电比容量达203.4 mAh.g-1,表现出良好的电化学性能。     

溶胶凝胶法制备片状氧化硅/氧化锆纳米复合材料(英文)

以氧氯化锆和二甲基二乙氧基硅烷为前驱体,在无任何表面活性剂的条件下,利用溶胶-凝胶法制备了片状SiO_2/ZrO_2复合材料.采用X射线衍射仪、扫描电镜、能谱仪、傅立叶变换红外光谱仪、透射电镜等分析了产物的结构和形貌,并探讨了SiO_2/ZrIO_2纳米复合材料的取向生长机理.结果表明,在正丁醇和水的混合溶液中制备的SiO_2/ZrO_2纳米复合材料的粒径为18nm,将干凝胶的500℃空气气氛中焙烧2h可以得到四方相片状氧化锆晶体.化合物中的硅原子通过Si—O—Zr化学键与锆原子相连;硅的引入仅影响氧化锆晶体的形貌,而不导致四方相氧化锆结构和尺寸的改变.本文所述方法可望拓展用于制备其他具有类似分级结构的无机功能纳米材料.     

Silica nanorings on the surfaces of layered silicate

A simple approach to the synthesis of clay-silica nanocomposites is presented. Silica nanorings on the edges of clay sheets were synthesized by using a modified St?ber method. Transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy, and fluorescence spectroscopy were employed to characterize the prepared nanocomposites. TEM results show that the average size of the nanorings increases with the growth of silica. XRD results indicate that the layered structures of clay can be found in the nanocomposite and the growth of silica nanorings expands the d spacing of clay platelets. The mechanism of the formation of the nanorings is discussed. The preparation of polystyrene (PS) brushes on the surfaces of silica nanorings by atom-transfer radical polymerization is also reported. The polymer nanocomposite with negatively charged clay surfaces and hydrophobic polymer brushes on the silica nanorings can be used in Pickering emulsions, and PS colloidal particles with clay-silica on the surfaces were prepared.     

Multiwalled carbon nanotubes drive the activity of metal@oxide core-shell catalysts in modular nanocomposites

Rational nanostructure manipulation has been used to prepare nanocomposites in which multiwalled carbon nanotubes (MWCNTs) were embedded inside mesoporous layers of oxides (TiO(2), ZrO(2), or CeO(2)), which in turn contained dispersed metal nanoparticles (Pd or Pt). We show that the MWCNTs induce the crystallization of the oxide layer at room temperature and that the mesoporous oxide shell allows the particles to be accessible for catalytic reactions. In contrast to samples prepared in the absence of MWCNTs, both the activity and the stability of core-shell catalysts is largely enhanced, resulting in nanocomposites with remarkable performance for the water-gas-shift reaction, photocatalytic reforming of methanol, and Suzuki coupling. The modular approach shown here demonstrates that high-performance catalytic materials can be obtained through the precise organization of nanoscale building blocks.     

纳米Ag/CNTs复合材料的制备、表征及对环三亚甲基三硝胺热分解的影响

采用银镜法和水热法制备了两种纳米Ag/CNTs(碳纳米管)复合材料, 利用傅里叶变换红外(FTIR)光谱、粉末X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜及能量散射光谱仪(SEM-EDS)对复合物的物相、组成、形貌和结构进行分析表征, 并运用差示扫描量热法(DSC)研究了纳米Ag/CNTs 复合材料对环三亚甲基三硝胺(RDX)热分解特性的影响. 结果表明: 纳米Ag 以10-80 nm的不规则球形“粘附”于纳米CNTs 表面,分散较均匀, 水热法制得的复合物表面纳米Ag较大、且负载的Ag粒子较多; 纳米Ag/CNTs 复合材料的加入改变了RDX的热分解过程, 使原有占主导的液相分解变为二次的气相反应加剧, RDX主分解峰形发生了明显的改变; 纳米Ag/CNTs 复合材料对RDX热分解的催化主要表现为分解温度的降低.     

Investigation the Effects of Green-Synthesized Copper Nanoparticles on the Performance of Activated Carbon-Chitosan-Alginate for the Removal of Cr(VI) from Aqueous Solution

In the present investigation, green nano-zerovalent copper (GnZVCu), activated carbon (AC), chitosan (CS) and alginate (ALG) nanocomposites were produced and used for the elimination of chromium (VI) from a polluted solution. The nanocomposites GnZVCu/AC-CS-alginate and AC-CS-alginate were prepared. Analysis and characterization were performed by the following techniques: X-ray diffraction, energy dispersive X-ray spectroscopy, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The SEM analysis revealed that the nanocomposites are extremely mesoporous, which leads to the greatest adsorption of Cr⁺⁶ (i.e., 97.5% and 95%) for GnZVCu/AC-CS-alginate and AC-CS-alginate, respectively. The adsorption efficiency was enhanced by coupling GnZVCu with AC-CS-alginate with a contact time of 40 min. The maximum elimination of Cr⁺⁶ with the two nanocomposites was achieved at pH 2. The isotherm model, Freundlich adsorption isotherm and kinetics model and P.S.O.R kinetic models were discovered to be better suited to describe the exclusion of Cr⁺⁶ by the nanocomposites. The results suggested that the synthesized nanocomposites are promising for the segregation of Cr⁺⁶ from polluted solutions, specially the GnZVCu/AC-CS-alginate nanocomposite.     

Direct synthesis of zirconia aerogel nanoarchitecture in supercritical CO2

The objective of the present study was to synthesize porous ZrO2 aerogels with a nanostructure via a direct sol-gel route in the green solvent supercritical carbon dioxide (scCO2). The synthesis involved the coordination and polycondensation of a zirconium alkoxide using acetic acid in CO2, followed by scCO2 drying and calcination. Either a translucent or opaque monolith was obtained, which was subsequently characterized by electron microscopy, X-ray diffraction, thermal analysis, N2 physisorption, and infrared spectroscopy analysis. The electron microscopy results showed that the translucent monolithic ZrO2 exhibited a well-defined mesoporous structure, while the opaque monolith, formed using added alcohol as a cosolvent, was composed of loosely compacted nanospherical particles with a diameter of ca. 20 nm. After calcination at 400 and 500 degrees C, X-ray diffraction results indicated that the ZrO2 exhibited tetragonal and/or monoclinic phases. In situ infrared spectroscopy results showed the formation of a Zr-acetate coordinate complex at the initial stage of the polycondensation, followed by further condensation of the complex into macromolecules.     

非晶态Ni-W/ZrO2复合镀层的制备、热处理及腐蚀行为

在镍钨合金电解液中, 通过搅拌使二氧化锆固体微粒悬浮, 电沉积制备Ni-W/ZrO2复合镀层. 研究结果表明, 二氧化锆粒子影响复合镀层的电沉积、表面形貌、结构、热处理过程和抗腐蚀性能; 与Ni-W合金的电沉积过程相比, 复合镀层中的W含量和电流效率均降低; 在400 ℃处理1 h后, 嵌入Ni-W本体中的ZrO2粒子脱落, W向镀层表面富集. 扫描电子显微镜(SEM)结果显示, 复合镀层呈现团粒状形态, 无裂纹. 差示扫描量热(DSC)分析结合X射线(XRD)衍射实验指出, Ni-W/ZrO2复合镀层为非晶态结构. 复合镀层的显微硬度较纳米晶Ni-W合金的高; 热处理后, 复合镀层的显微硬度和在3%氯化钠溶液中的抗腐蚀行为显著增强.     

Ternary Ag/Polyaniline/Au nanocomposites: Preparation,characterization and electrochemical properties

Ternary Ag/Polyaniline/Au nanocomposites were synthesized successfully by immobilizing of Au nanoparticles (NPs) on the surface of Ag/Polyaniline (PANI) nanocomposites. Ag/PANI nanocomposites were prepared via in situ chemical polymerization of aniline in the presence of 4-aminothiophenol (4-ATP) capped silver colloidal NPs. Then, uniform gold (Au) NPs were assembled on the surface of resulted Ag/PANI nanocomposites through electrostatic interaction to get Ag/Polyaniline/Au nanocomposites. The nanocomposites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), ultraviolet visible spectroscopy (UV-Vis), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). Moreover, Ag/PANI/Au nanocomposites were immobilized on the surface of a glassy carbon electrode and showed enhanced electrocatalytic activity for the reduction of H₂O₂ compared with Ag/PANI.     

Preparation of mesoporous TiO2/CNT nanocomposites by synthesis of mesoporous titania via EISA and their photocatalytic degradation under visible light irradiation

Stabilized mesoporous TiO₂ was synthesized by evaporation induced self assembly (EISA) method and mechanically incorporated into single-walled carbon nanotubes (SWCNT) with different ratios. The physicochemical properties of the nanocomposites (mesoporous TiO₂/SWCNT) materials were investigated by Brunauer–Emmett–Teller (BET) measurement, X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), photoluminescence (PL) and ultraviolet–visible (UV–Vis) spectroscopy measurements. The catalytic activity of mesoporous TiO₂ and nanocomposites were assessed by examining the degradation of rhodamine B as model aqueous solution under visible light. CNTs are facilitating the photocatalytic activity of mesoporous TiO₂ in the degradation of rhodamine B efficiently.     

Role of ionene in composition of porous structure of template-synthesized silicas

Effect of the presence of I-4 Me-Ph ionene in the supramolecular template (cetyltrimethylammonium bromide) on formation of porous structure of silicas has been studied. As-synthesized nanocomposites were characterized by using thermal analysis. Nitrogen adsorption–desorption measurements, X-ray diffraction and scanning electronic microscopy were applied to determine adsorption-structural characteristics and morphology of particles of the mesoporous templated silicas prepared in basic media.     

由纳米晶前驱体组装有序介孔silicalite-1分子筛

采用两步法将不同尺寸的silicalite-1分子筛纳米晶种通过自组装合成了一系列有序介孔silicalite-1分子筛。首先将强碱性的silicalite-1前驱体分别加热不同时间得到纳米晶种,然后在类似合成SBA-15的强酸性条件下组装成有序的介孔材料。合成条件的剧烈变化阻止了分子筛晶种的继续长大,并在三嵌段共聚物模板的诱导下组装成有序介孔材料。这种“自下而上”的方法制备有序介孔分子筛同时包含微孔和介孔。氮气吸脱附结果表明所制备的介孔分子筛材料均表现了很大的比表面积(730 m2/g以上)。     

Synthesis of thermally stable zirconia-based mesoporous materials via a facile post-treatment

A novel method of preparing thermally stable zirconia-based mesoporous materials was developed. The zirconia-based mesoporous materials of 2D-hexagonal structure were prepared using zirconium sulfate as the zirconium precursor and cetyltrimethylammonium (CTMA) as the pore-directing agent with the aid of salt in the synthesis solution to reduce the sulfate content in the final product and significantly improve the crystallographic ordering. Post-treatment of the mesoporous material with NaCl solution and lowering the ramping rate to less than 0.2 degrees C/min during the calcination process, however, were the key steps to hinder the growth of the dense zirconia phase and to retain the ordered mesostructure up to 600 degrees C. It was found that a portion of the surfactant (8.9-17.4 wt %) and sulfate ions (0.5-1.2 wt %) were removed during the post-treatment, which prevented the remaining sulfate groups from being reduced by the hydrogen-rich surfactant during the calcination process as confirmed by sulfur K-edge X-ray absorption near edge structure (XANES) and infrared spectroscopy. The maintenance of sulfur in the sulfate state seemed to be important in stabilizing the mesoporous structure of zirconia materials. The mesoporous zirconia materials after extraction with NaCl solution three times and calcination at 550-600 degrees C had the composition ZrO(2-x)(SO4)x with x = 0.10-0.27. The material possesses high surface area (approximately 200 m2/g), large pore volume (approximately 0.10 cm3/g), and wormlike mesopores. In comparison with the mesoporous zirconia materials stabilized by chemical treatment, the present route was simpler and more environmentally friendly and resulted in mesoporous zirconia materials of better thermal stability.     

催化剂载体对硼氢化钠在纳米金电极上电氧化行为的影响

分别以中孔炭(MPC)和VXC-72R炭黑作载体,制备了中孔炭载纳米Au粒子(Au/MPC)和VXC-72R炭黑载纳米Au粒子(Au/CB),并将其用作直接硼氢化钠燃料电池阳极电氧化催化剂.分别用X-射线衍射(XRD)、透射电镜(TEM)等比较了不同载体催化剂的结构和形貌.结果表明,纳米Au粒子均为面心立方结构,Au/MPC中纳米Au粒子的粒径为16nm左右比Au/CB中的纳米Au粒子的更小,且均匀分散在载体的表面.用循环伏安曲线和动电位极化曲线等比较了不同载体催化剂的电化学特性.结果表明,Au/CB的电流密度为38.10mA·cm-2,而Au/MPC的电流密度达到42.88mA·cm-2,比Au/CB的电流密度提高了12.5%.     

In situ introduction of dispersed metallic Ag nanoparticles into the channels of mesoporous carbon CMK-3

An in situ reduction method has been developed to fabricate metallic Ag nanoparticles inside the channels of mesoporous carbon CMK-3.This approach combines function of the CMK-3 surface by oxidation using HNO_3 with the subsequent absorption of Ag~ . The resultant nanocomposite materials were characterized by nitrogen adsorption,X-ray diffraction,Auger electron spectroscopy and transmission electron microscopy.Compared with the conventional impregnation method,our approach shows that Ag nanoparticles of 2-4 nm can be uniformly incorporated into CMK-3.     

Ultrasound-assisted synthesis of mesoporous zirconia-hydroxyapatite nanocomposites and their dual surface affinity for Cr3+/Cr2O7(2-) ions

Zirconia-hydroxyapatite nanocomposites were prepared by sol-gel deposition of zirconium oxide from a zirconium alkoxide in the presence of apatite colloidal suspension under ultrasonication. The material porosity evolves from mainly microporous zirconia to mesoporous hydroxyapatite, with decreasing surface area and increasing pore volume. XRD studies indicate that the apatite phase is well-preserved within the composite materials. The homogeneous dispersion of apatite colloids within the zirconia network was supported by TEM observations and nitrogen sorption measurements. (31)P solid-state NMR studies suggest that partial dissolution of apatite may have occurred during the preparation, leading to the adsorption of phosphate species on zirconia particles. This is confirmed by XRD studies of nanocomposites after thermal treatment that demonstrate the preferred formation of tetragonal over monoclinic ZrO(2) in the presence of hydroxyapatite. In order to investigate the surface properties of these novel materials, the adsorption of Pb(2+), Cr(3+), and Cr(2)O(7)(2-) was evaluated. Metal cations were preferentially adsorbed on apatite-rich composites, whereas Cr(2)O(7)(2-) shows a good affinity for the zirconia-rich phases. Zirconia-apatite materials showed the most promising performance in terms of recyclability. These nanocomposites that combine microporosity, mesoporosity and dual sorption properties for these species appear as interesting materials for metal ion remediation and may also find applications as biomaterials.     

Multifunctional magnetic mesoporous silica nanocomposites with improved sensing performance and effective removal ability toward Hg(II)

In the present work, a multifunctional inorganic-organic hybrid nanomaterial (MMS-Py) was prepared by the immobilization of a pyrene-based receptor (Py) within the channels of magnetic mesoporous silica nanocomposites (MMS), and characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, N(2) adsorption/desorption, superconducting quantum interference device, and photoluminescence spectra. This multifunctional nanomaterial exhibits superparamagnetic behavior, ordered mesoporous characteristics, and significantly improved fluorescence sensing properties that allow for highly sensitive and reproducible Hg(2+) detection. The fluorogenical responses of MMS-Py are stable over a broad pH range. A detection limit of 1.72 ppb is obtained, which is 2 orders of magnitude lower than that based on bulk mesoporous materials. Additionally, this nanomaterial shows high performance in convenient magnetic separability and efficient removal of Hg(2+). These results indicate that these multifunctional nanocomposites may find potential applications for simple detection and easy removal of Hg(2+) in biological, toxicological, and environmental areas.     

Improvement of ammonia sensing properties of polypyrrole by nanocomposite with graphitic materials

The more sensitive and rapid ammonia gas sensors were prepared with nanocomposites of polypyrrole (PPy) and graphitic materials such as graphite, graphite oxide (GO), and reduced graphene oxide (RGO). Pyrrole was polymerized uniformly on the surface of graphitic materials by in situ polymerization method. The structures of nanocomposites were studied by scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy indicating the well-exfoliated GO and RGO in PPy matrix with favorable interfacial interaction. PPy/RGO nanocomposite showed the highly improved response in detecting ammonia gas mainly due to the effective electron charge transfer between PPy and ammonia and the efficient transfer of electrical resistance variation by the uniformly dispersed conductive RGO in PPy. PPy/RGO nanocomposite gas sensor also showed the excellent reproducibility in ammonia sensing behavior during the recovery process at lower temperature of 373 K.     

Synthesis and characterization of active ester-functionalized polypyrrole-silica nanoparticles: application to the covalent attachment of proteins

Novel ester-functionalized polypyrrole-silica nanocomposite particles were prepared by oxidative copolymerization of pyrrole and N-succinimidyl ester pyrrole (50/50% initial concentrations), using FeCl3 in the presence of ultrafine silica nanoparticles (20 nm diameter). The N-succinimidyl ester pyrrole monomer was prepared in aqueous solution using 1-(2-carboxyethylpyrrole) and N-hydroxysuccinimide in the presence of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide. The resulting nanocomposites (N-succinimidyl ester polypyrrole-silica) are raspberry-shaped agglomerates of silica sol particles "glued" together by the insoluble poly(pyrrole-co-N-succinimidyl pyrrole). The N-succinimidyl ester polypyrrole-silica particles were characterized in terms of their size, density, copolymer content, and polydispersity. Scanning electron microscopy and disk centrifuge sedimentometry confirmed that the nanocomposite particles had narrow size distributions. X-ray photoelectron spectroscopy analysis indicated a silica-rich surface and a high surface concentration of N-succinimidyl ester groups. These nanoparticles exhibited good long-term dispersion stability. The chemical stability of the ester functions in aqueous media after several weeks of storage was monitored by FTIR spectroscopy. The functionalized nanocomposites were tested as bioadsorbents of human serum albumin (HSA). The very high amount of immobilized HSA determined by UV-visible spectroscopy is believed to be due to covalent binding. Incubation of the HSA-grafted nanocomposite with anti-HSA resulted in immediate flocculation, an indication that they are alternative candidates for visual diagnostic assays.     

Interaction of Au with thin ZrO2 films: influence of ZrO2 morphology on the adsorption and thermal stability of Au nanoparticles

The model catalysts of ZrO(2)-supported Au nanoparticles have been prepared by deposition of Au atoms onto the surfaces of thin ZrO(2) films with different morphologies. The adsorption and thermal stability of Au nanoparticles on thin ZrO(2) films have been investigated using synchrotron radiation photoemission spectroscopy (SRPES) and X-ray photoelectron spectroscopy (XPS). The thin ZrO(2) films were prepared by two different methods, giving rise to different morphologies. The first method utilized wet chemical impregnation to synthesize the thin ZrO(2) film through the procedure of first spin-coating a zirconium ethoxide (Zr(OC(2)H(5))(4)) precursor onto a SiO(2)/Si(100) substrate at room temperature followed by calcination at 773 K for 12 h. Scanning electron microscopy (SEM) investigations indicate that highly porous "sponge-like nanostructures" were obtained in this case. The second method was epitaxial growth of a ZrO(2)(111) film through vacuum evaporation of Zr metal onto Pt(111) in 1 × 10(-6) Torr of oxygen at 550 K followed by annealing at 1000 K. The structural analysis with low energy electron diffraction (LEED) of this film exhibits good long-range ordering. It has been found that Au forms smaller particles on the porous ZrO(2) film as compared to those on the ordered ZrO(2)(111) film at a given coverage. Thermal annealing experiments demonstrate that Au particles are more thermally stable on the porous ZrO(2) surface than on the ZrO(2)(111) surface, although on both surfaces, Au particles experience significant sintering at elevated temperatures. In addition, by annealing the surfaces to 1100 K, Au particles desorb completely from ZrO(2)(111) but not from porous ZrO(2). The enhanced thermal stability for Au on porous ZrO(2) can be attributed to the stronger interaction of the adsorbed Au with the defects and the hindered migration or coalescence resulting from the porous structures.