Paper‐Based Electronic Tongue

We present a low cost paper‐based electronic tongue capable of discriminating forged water samples. System comprises of 4 paper‐based potentiometric sensors (sensitive to Cl^?, Na⁺/K⁺, Ca²⁺/Mg²⁺, ) and a traditional Ag/AgCl reference electrode. Different electrode materials and methods of insulation were tested with best results obtained for pencil graphite and lamination. The presented electronic tongue was able to distinguish tap and lake water from mineral water samples (PCA – Principal Component Analysis and KNN ? K‐nearest neighbour). In total 14 different water samples were used in this study. Sensors presented good signal repeatability, selectivity and reasonable sensitivity.     

Pencil‐drawn Paper‐based Non‐invasive and Wearable Capacitive Respiration Sensor

This paper describes a fully‐drawn pencil‐on‐paper based low‐cost capacitive sensor for non‐invasive respiration monitoring. The sensor utilizes the hygroscopic character of the paper to measure the breathing rate and pattern. The adsorption and desorption of water molecules on paper during inhalation and exhalation results in variation in its dielectric constant. This change in dielectric constant during respiration reflects the change in capacitance of the sensor. By interfacing the sensor with the microcontroller, the capacitance data was acquired and transferred to a smartphone through Bluetooth communication. Being a low cost, wearable, non‐invasive and disposable sensor, it holds tremendous potential in healthcare technology and can be commercialized into a viable product for easy‐to‐use diagnostic purpose.     

Paper‐Based Inkjet‐Printed Microfluidic Analytical Devices

Rapid, precise, and reproducible deposition of a broad variety of functional materials, including analytical assay reagents and biomolecules, has made inkjet printing an effective tool for the fabrication of microanalytical devices. A ubiquitous office device as simple as a standard desktop printer with its multiple ink cartridges can be used for this purpose. This Review discusses the combination of inkjet printing technology with paper as a printing substrate for the fabrication of microfluidic paper‐based analytical devices (μPADs), which have developed into a fast‐growing new field in analytical chemistry. After introducing the fundamentals of μPADs and inkjet printing, it touches on topics such as the microfluidic patterning of paper, tailored arrangement of materials, and functionalities achievable exclusively by the inkjet deposition of analytical assay components, before concluding with an outlook on future perspectives.     

A Disposable Planar Paper‐Based Potentiometric Ion‐Sensing Platform

Ion‐selective electrodes (ISEs) are widely used tools for fast and accurate ion sensing. Herein their design is simplified by embedding a potentiometric cell into paper, complete with an ISE, a reference electrode, and a paper‐based microfluidic sample zone that offer the full function of a conventional ISE setup. The disposable planar paper‐based ion‐sensing platform is suitable for low‐cost point‐of‐care and in‐field testing applications. The design is symmetrical and each interfacial potential within the cell is well defined and reproducible, so that the response of the device can be theoretically predicted. For a demonstration of clinical applications, paper‐based Cl^? and K⁺ sensors are fabricated with highly reproducible and linear responses towards different concentrations of analyte ions in aqueous and biological samples. The single‐use devices can be fabricated by a scalable method, do not need any pretreatment prior to use, and only require a sample volume of 20 μL.     

Paper‐Origami‐Based Multiplexed Malaria Diagnostics from Whole Blood

We demonstrate, for the first time, the multiplexed determination of microbial species from whole blood using the paper‐folding technique of origami to enable the sequential steps of DNA extraction, loop‐mediated isothermal amplification (LAMP), and array‐based fluorescence detection. A low‐cost handheld flashlight reveals the presence of the final DNA amplicon to the naked eye, providing a “sample‐to‐answer” diagnosis from a finger‐prick volume of human blood, within 45 min, with minimal user intervention. To demonstrate the method, we showed the identification of three species of Plasmodium, analyzing 80 patient samples benchmarked against the gold‐standard polymerase chain reaction (PCR) assay in an operator‐blinded study. We also show that the test retains its diagnostic accuracy when using stored or fixed reference samples.     

Paper‐Based Electrochemiluminescent 3D Immunodevice for Lab‐on‐Paper,Specific, and Sensitive Point‐of‐Care Testing

Recent research on microfluidic paper‐based analytical devices (μPADs) has shown that paper has great potential for the fabrication of low‐cost diagnostic devices for healthcare and environmental monitoring applications. Herein, electrochemiluminescence (ECL) was introduced for the first time into μPADs that were based on screen‐printed paper‐electrodes. To further perform high‐specificity, high‐performance, and high‐sensitivity ECL on μPADs for point‐of‐care testing (POCT), ECL immunoassay capabilities were introduced into a wax‐patterned 3D paper‐based ECL device, which was characterized by SEM, contact‐angle measurement, and electrochemical impedance spectroscopy. With the aid of a home‐made device‐holder, the ECL reaction was triggered at room temperature. By using a typical tris(bipyridine)ruthenium–tri‐n‐propylamine ECL system, this paper‐based ECL 3D immunodevice was applied to the diagnosis of carcinoembryonic antigens in real clinical serum samples. This contribution further expands the number of sensitive and specific detection modes of μPADs.     

Polyion Detection via All‐solid‐contact Paper‐based Polyion‐sensitive Polymeric Membrane Electrodes

The first all‐solid‐contact paper‐based single‐use polyion‐sensitive ion‐selective electrodes (ISEs) are described. These polyion‐sensitive ISEs are fabricated using cellulose filter paper coated with a carbon ink conductive layer. A polyanion sensing membrane is cast on a section of the coated paper and the sensor is insulated, resulting in a disposable, single‐use device. Various polyanions are shown to yield large negative potentiometric responses when using these disposable devices for direct polyanion detection. These new sensors are further demonstrated to be useful in indirect polycation detection when polycations (i. e., polyquaterniums (PQs)) are titrated with polyanionic dextran sulfate (DS). Titrations monitored using these paper‐based, all‐solid‐contact devices yield endpoints proportional to the given PQ concentration present in the test sample.     

Riboflavin‐Based Fluorogenic Sensor for Chemo‐ and Enantioselective Detection of Amine Vapors

A novel turn‐on fluorogenic chiral sensory system has been developed using a protonated riboflavin and riboflavin‐derived cationic polymer as a fluorophore precursor and a specific amine receptor, respectively, which enables the solid‐state chemo‐ and enantioselective fluorogenic visual detection of primary and secondary amine vapors.     

Amperometric Sniffer for Volatile Amines Based on Paper‐Supported Room Temperature Ionic Liquids Enabling Rapid Assessment of Fish Spoilage

A gas sensors based on a room temperature ionic liquid (RTIL) supported on paper is proposed as amperometric sniffer for monitoring volatile amines (VAs) released from fish samples, in order to gain indication of their state of turning spoiled. It was used as a paper electrochemical detector (PED) for a flow injection system in which controlled headspace volumes in equilibrium with ice‐stored fish samples were directly injected. The performance of this RTIL‐PED sensor was preliminarily tested on synthetic samples of trimethylamine (TMA), dimethylamine (DMA), methylamine (MA) and ammonia (i.e. the main species responsible for the typical flavor of spoiled fish), thus verifying that only TMA, DMA and MA can be detected because NH₃ oxidation occurred beyond the solvent discharge. This notwithstanding, detection of the sole TMA, DMA and MA as a whole turned out to be well suited for the rapid assessment of fish spoilage, since during storage the release enhancement for these amines is largely predominant over that of NH₃. Repeatable (8 % RSD) sharp peaks were detected for all amines above over a wide range (5–1000 nmol) and a detection limit of a little more than 3 nmol was inferred for a signal‐to‐noise ratio of 3. This approach was applied to the detection of VAs released from real fish samples (sardines), in parallel to the determination of their total volatile basic nitrogen (TVBN), which is a conventional indicator frequently adopted for the chemical quality assessment of fish. A substantially satisfactory agreement was found by comparing the data achieved by these two approaches.     

High Performance Non‐enzymatic Glucose Sensor Based on One‐Step Electrodeposited Nickel Sulfide

Nanostructured NiS thin film was prepared by a one‐step electrodeposition method and the structural, morphological characteristics of the as‐prepared films were analyzed by X‐ray diffractometry (XRD), field emission scanning electron microscopy (FESEM) and energy dispersive X‐ray analysis (EDAX). The electrocatalytic activity of NiS thin film towards glucose oxidation was investigated by fabricating a non‐enzymatic glucose sensor and the sensor performance was studied by cyclic voltammetry (CV) and amperometry. The fabricated sensor showed excellent sensitivity and low detection limit with values of 7.43 μA μM ^?1 cm^?2 and 0.32 μM , respectively, and a response time of <8 s.     

石墨烯纸的制备及电容特性

利用未经任何分散处理的氧化石墨溶胶在气-液界面自组装得到氧化石墨纸(ϕ=10 cm), 将氧化石墨纸在不同温度下用水合肼蒸气还原制得石墨烯纸. 采用扫描电子显微镜(SEM)、 X射线衍射(XRD)、 Raman光谱、 X射线光电子能谱(XPS)及氮吸附对还原前后样品的微观结构、 表面特性、 元素组成及比表面积进行了表征, 在此基础上考察了还原处理及还原温度对材料电容特性的影响. 结果表明, 在150 ℃下还原氧化石墨纸得到的石墨烯纸具有较好的电化学电容特性, 其在1000 mA/g恒定充放电电流密度下, 6 mol/L KOH电解质溶液中的质量比电容达到142 F/g, 1000次充放电循环后电容保持率为99.8%.     

Electrochemical Glutathione Sensor Based on Electrochemically Deposited Poly‐m‐aminophenol

Preparation and characterization of electrodes suitable for determination of glutathione is reported in this study. For this poly‐m‐aminophenol (PmAP), poly‐o‐aminophenol, and poly‐p‐aminophenol were electrochemically deposited from aqueous solution on the surface of glassy carbon (GC) electrode by potential cycling in the range of +0.2–+1.0 V. The modified GC electrodes were characterized by cyclic voltammetry, electrochemical impedance spectroscopy, contact angle measurement and ellipsometry. It was found that poly‐m‐aminophenol modified GC electrode (PmAP/GC‐electrode) is most suitable for electroanalytical determination of glutathione. An electroanalytical system for the determination of glutathione based on the PmAP/GC‐electrode was developed. The analytical system was characterized by low limit of detection, good stability, high sensitivity and wide linear detection range.     

Utilizing Paper‐Based Devices for Antimicrobial‐Resistant Bacteria Detection

Antimicrobial resistance (AMR), the ability of a bacterial species to resist the action of an antimicrobial drug, has been on the rise due to the widespread use of antimicrobial agents. Per the World Health Organization, AMR has an estimated annual cost of USD 34 billion in the US and is predicted to be the number one cause of death worldwide by 2050. One way AMR bacteria can spread, and by which individuals can contract AMR infections, is through contaminated water. Monitoring AMR bacteria in the environment currently requires that samples be transported to a central laboratory for slow and labor intensive tests. We have developed an inexpensive assay using paper‐based analytical devices (PADs) that can test for the presence of β‐lactamase‐mediated resistance. To demonstrate viability, the PAD was used to detect β‐lactam resistance in wastewater and sewage and identified resistance in individual bacterial species isolated from environmental water sources.