Preparation and Characterizations of ZnTiO<Subscript>3</Subscript> Powders by Sol–Gel Process

ZnTiO₃ powders were prepared by a sol–gel method. The gelation conditions and the gelation mechanism were investigated. The crystallization behavior and characteristics of the ZnTiO₃ were also investigated in detail. The experimental results show that homogenous and translucent gels can be prepared when the gelation conditions are appropriate and the gelation temperature remains constant. The gel structure can be described as a network of Ti and O, in which zinc ions are well distributed. The ZnTiO₃ phase can be detected by XRD in the powders calcined above 700 °C. The formation of ZnTiO₃ is a slow reaction process, which leads to the development of large ZnTiO₃ particles, with dimensions after calcination at 900 °C for 2 h in the range of 30–50 m.     

Effects of Calcination on the Physical and Photocatalytic Properties of TiO<Subscript>2</Subscript> Powders Prepared by Sol–Gel Template Method

TiO₂ powders were prepared by sol–gel template method and calcined under different conditions. XRD, BET and TEM were used to characterize the TiO₂ powders obtained. The photocatalytic activity of TiO₂ was investigated by the degradation of methyl orange. It was found that TiO₂ powder has the highest photocatalytic activity at a calcination temperature of 673 K. The effects of physical properties such as surface area, crystallinity and crystal phase on the photocatalytic activity of TiO₂ were discussed.     

Sensor Performance of Nanostructured TiO<Subscript>2</Subscript>–SnO<Subscript>2</Subscript> Films Prepared by an Aqueous Sol–Gel Process

Nanostructured TiO₂–SnO₂ thin films and powders were prepared by a facile aqueous particulate sol–gel route. The prepared sols showed a narrow particle size distribution with hydrodynamic diameter in the range 17.2–19.3 nm. Moreover, the sols were stable over 5 months, since the constant zeta potential was measured during this period. The effect of Sn:Ti molar ratio was studied on the crystallisation behaviour of the products. X-ray diffraction analysis revealed that the powders were crystallised at the low temperature of 400 °C containing anatase-TiO₂, rutile-TiO₂ and cassiterite-SnO₂ phases, depending on annealing temperature and Sn:Ti molar ratio. Furthermore, it was found that SnO₂ retarded the anatase to rutile transformation up to 800 °C. The activation energy of crystallite growth was calculated in the range 0.96–6.87 kJ/mol. Transmission electron microscope image showed that one of the smallest crystallite sizes was obtained for TiO₂–SnO₂ binary mixed oxide, being 3 nm at 600 °C. Field emission scanning electron microscope analysis revealed that the deposited thin films had nanostructured morphology with the average grain size in the range 20–40 nm at 600 °C. Thin films produced under optimized conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO gas at low operating temperature of 200 °C, resulting in increased thermal stability of sensing films as well as a decrease in their power consumption.     

Studies on structure and electrochemical properties of pillared M–MnO<Subscript>2</Subscript> (M=Ba<Superscript>2+</Superscript>, Sr<Superscript>2+</Superscript>, ZrO<Superscript>2+</Superscript>)

Supramolecular pillared oxides were prepared through the intercalation of M²⁺ cations into a MnO₂ host matrix by the method of ion exchange between the precursor δ-K _x MnO₂ and the corresponding guest. The materials M-MnO₂ crystallize in the hexagonal system, the same structure as the precursor, with a larger interlamellar spacing. In the case of ZrO-MnO₂, extended X-ray absorption fine structure (EXAFS) determination indicates that the Zr atom locates between the MnO₂ layers forming a stable structure. Compared with the precursor, the cycling property of M-MnO₂ was improved distinctly, while the capacity decreased to some degree due to the strong interaction between pillars and the host matrix. Among these pillared materials, ZrO-MnO₂ has an advanced reversible capacity of 161.5 mAh·g⁻¹ and improved cycling behavior compared with the precursor.     

Synthesis of Ca<Subscript>3</Subscript>Al<Subscript>6</Subscript>Si<Subscript>2</Subscript>O<Subscript>16</Subscript>: Ce<Superscript>3+</Superscript>, Tb<Superscript>3+</Superscript> phosphors by sol–gel method and optical properties

Ca₃Al₆Si₂O₁₆: Ce³⁺, Tb³⁺ phosphors have been prepared by sol–gel method. The structure and photoluminescence properties were studied with careful. The results indicated that the single-phased Ca₃Al₆Si₂O₁₆ phosphors crystallize at 1,000 °C for 2 h in conventional furnace. With appropriate concentrations of Ce³⁺ and Tb³⁺ ions into Ca₃Al₆Si₂O₁₆ matrix, these materials exhibit blue phosphors and white light under ultraviolet radiation. White-light emission can be achieved because of a 400 nm emission ascribed to transitions of Ce³⁺ ions and three sharp peaks at 487, 543, 585 nm, respectively, resulting from transitions of Tb³⁺ ions.     

Sol–gel synthesis and characterization of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> nanocrystalline powder

Al₂O₃–TiO₂ nanocrystalline powders were synthesized by sol–gel process. Aluminum sec-butoxide and titanium isopropoxide chemicals were used as precursors and ethyl acetoacetate was used as chelating agent. Thermal and crystallization behaviors of the precursor powders were investigated by thermal gravimetric-differential thermal analysis, Fourier-transform infrared spectrum and X-ray diffraction. The average crystalline size of heat treated Al₂O₃–TiO₂ powders at 1,100 °C is ~100 nm.     

Sol–gel synthesis of Eu<Superscript>3+</Superscript>: Tb<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> nanophosphor

Eu (0.1, 0.5 and 1.0 mol%) doped Tb₃Al₅O₁₂ (TAG) was prepared by sol–gel technique through nitrate-citrate route followed by sintering in air (1,100 °C maximum temperature). XRD analysis showed that Eu³⁺ enters the TAG lattice substitutionally replacing the Tb³⁺ ion. Both XRD as well as FTIR investigation showed improvement in crystalline phase with the increase in the sintering temperature. SEM and TEM analysis showed that the powder contains the particles in 5–20 nm size with almost spherical morphology. The excitation spectrum recorded in 300–500 nm showed dominant absorption due to Tb³⁺ while the emission spectra recorded with 380 nm excitation had strong red emission characteristic of Eu³⁺. The intensity of this emission increases with the increase of the Eu concentration from 0.1 to 0.5 mol%. However, the emission intensity decreased on further increase in Eu concentration to 1.0 mol%. This intensity variation with dopant concentration is attributed to well-known “concentration quenching” observed in rare-earth doped materials. Reasonably strong red emission due to Eu was observed when excited with the blue (480 nm) radiation of a Xe lamp indicating the usefulness of the material for the realization of white light LED.     

Preparation,characterization and photocatalytic properties of TiO<Subscript>2</Subscript> nanostructured spheres synthesized by the Sol–Gel method modified with ethylene glycol

Monodispersed nanostructured TiO₂ spheres were obtained by the Sol–Gel method modified with ethylene glycol. The sample morphology and surface textural properties were characterized by X-ray diffraction (XRD), N₂-physisorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and diffuse reflectance spectroscopy (DRS). The SEM image showed spheres with sizes ranging from 600 to 700 nm. In addition, HRTEM micrographs reveal hexagonal grains slightly elongated (20 nm). The powders present a BET surface area of 116 m² g⁻¹. Samples without thermal treatment and those treated at 400 °C both showed characteristic reflections of the anatase phase. The photocatalytic activity of the prepared TiO₂ spheres was determined by degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) in aqueous solution. Kinetics parameters have displayed than the nanostructured material present a reaction half-life time of 30 min and it was two times faster than commercial TiO₂ (P25).     

Identification of Anionic Supramolecular Complexes of Sulfonamide Receptors with Cl<Superscript>−</Superscript>, NO<Stack><Subscript>3</Subscript><Superscript>−</Superscript></Stack>, Br<Superscript>−</Superscript>, and I<Superscript>−</Superscript> by APCI-MS

As part of a mass spectrometric investigation of the binding properties of sulfonamide anion receptors, an atmospheric pressure chemical ionization mass spectrometric (APCI-MS) method involving direct infusion followed by thermal desorption was employed for identification of anionic supramolecular complexes in dichloromethane (CH₂Cl₂). Specifically, the dansylamide derivative of tris(2-aminoethyl)amine (tren) (1), the chiral 1,3-benzenesulfonamide derivatives of (1R,2S)-(+)-cis-1-amino-2-indanol (2), and (R)-(+)-bornylamine, (3), were shown to bind halide and nitrate ions in the presence of (n−Bu)₄N⁺X⁻ (X⁻ = Cl⁻, NO₃⁻, Br⁻, I⁻). Solutions of receptors and anions in CH₂Cl₂ were combined to form the anionic supramolecular complexes, which were subsequently introduced into the mass spectrometer via direct infusion followed by thermal desorption. The anionic supramolecular complexes [M+X]⁻, (M=1–3, X⁻=Cl⁻, NO₃⁻, Br⁻, I⁻) were observed in negative mode APCI-MS along with the deprotonated receptors [M−H]⁻. Full ionization energy of the APCI corona pin (4.5 kV) was necessary for obtaining mass spectra with the best signal-to-noise ratios.     

H<Subscript>2</Subscript>-Sensing Characteristics of Nanocrystalline La<Subscript>0.8</Subscript>Pb<Subscript>0.2</Subscript>FeO<Subscript>3</Subscript> Prepared by Sol–Gel Method

Nanocrystalline La_0.8Pb_0.2FeO₃ has been prepared by the sol-gel method. XRD patterns show that the nanocrystalline La_0.8Pb_0.2FeO₃ is a perovskite phase with the orthorhombic structure and its mean crystallite size is about 19 nm. The influence of Pb ions which replaced the La ions on A-sites can be directly observed from the electrical and sensing properties to H₂ gas. The conductance of La_0.8Pb_0.2FeO₃-based sensor is considerably higher than that of LaFeO₃-based sensor, and Pb-doping can enhance the sensitivity to H₂ gas. An empirical relationship of with α = 0.668 was obtained.     

Sol–Gel Derived Rh/TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> Nanocomposite Membranes

A porous borosilicate substrate has been coated with base catalysed SiO₂ sol–gel nanoparticles. Onto these were deposited the vapour of titanium isopropoxide, where it reacted with the surface OH groups to give a TiO₂-overcoat. This nanocomposite sol–gel derived TiO₂/SiO₂ membrane was then doped with 1%Rh giving Rh/TiO₂/SiO₂ membranes. These are shown to be coherent and crack-free, to have good permeability and activity in the isomerisation of butanes. It appears that sol–gel chemistry will allow such membranes to be totally engineered at a nm level.     

Coagulation and heterocoagulation interactions of components in aqueous dispersed systems microcrystalline cellulose–TiO<Subscript>2</Subscript>, microcrystalline cellulose–TiOSO<Subscript>4</Subscript>, and TiO<Subscript>2</Subscript>–TiOSO<Subscript>4</Subscript>

A procedure was developed for recovery and concentration of residual palladium(II) from a “lean” refining solution by extraction with 1Н-1,2,4-triazole derivatives. Palladium(II) is extracted quantitatively from 1 M hydrochloric acid solutions and under optimum conditions is selectively separated from platinum(IV) and rhodium(III).     

Colour tuneability and white light generation in Yb<Superscript>3+</Superscript>–Ho<Superscript>3+</Superscript>–Tm<Superscript>3+</Superscript> co-doped SiO<Subscript>2</Subscript>–LaF<Subscript>3</Subscript> nano-glass-ceramics prepared by sol–gel method

Nanostructured transparent glass-ceramics with composition of 95SiO₂–5LaF₃ co-doped with 0.3Yb³⁺, 0.1Ho³⁺ and 0.1Tm³⁺ (mol%) were synthesized by thermal treatment of precursor sol–gel derived glasses. X-ray diffraction and transmission electron microscopy analysis point out the precipitation of hexagonal LaF₃ nanocrystals with diameter ranging from 11 to 20 nm in these nano-glass-ceramics. White light generation by means of efficient blue, green and red up-conversion luminescence under infrared excitation at 980 nm was observed and involved mechanisms were analyzed. Colour tuneability is achieved by varying the up-conversion emission ratios as a function of pump power.     

Single-phased white-light emitting CaAl<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>8</Subscript>: Eu<Superscript>2+</Superscript>, Mn<Superscript>2+</Superscript> phosphors prepared by a sol–gel method

CaAl₂Si₂O₈: Eu²⁺, Mn²⁺ phosphors have been prepared by a sol–gel method. X-ray diffractometer, spectrofluorometer and UV–Vis spectrometer were used to characterize structural and optical properties of the samples. The results indicate that anorthite (CaAl₂Si₂O₈) directly crystallizes at 1000 °C in the sol–gel process. CaAl₂Si₂O₈: Eu²⁺, Mn²⁺ phosphors show two emission bands excited by ultraviolet light. Blue (around 415 nm) and yellow (around 575 nm) emissions originate from Eu²⁺ and Mn²⁺, respectively. With appropriate tuning of Mn²⁺ content, CaAl₂Si₂O₈: Eu²⁺, Mn²⁺ phosphors exhibit different hues and relative color temperatures.     

Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript>,Tb<Superscript>3+</Superscript> thin films prepared by sol–gel method: structural and optical studies

Y₂O₃: Eu³⁺,Tb³⁺ transparent, high density and optical quality thin films were prepared by the sol–gel dip-coating technique. Yttrium (III) 2,4-pentadionate was used as a precursor by its hydrolysis in ethanol. The doping agents were incorporated in the form of europium and terbium nitrate. Structural, morphological and optical properties of prepared films were investigated for different annealing temperatures in order to establish the ideal processing route that enhances the luminescent properties. X-ray diffraction (XRD) analysis shows the cubic phase for 10-layer films and annealing temperatures higher than 500°C. At 700°C, highly densified (4.52 g cm⁻³) and very smooth films (1.4 nm at 700°C) are produced, composed of crystallites with a grain size of 11 nm. The film thickness, refractive index and porosity, as well as the luminescent properties, were found to vary with treatment temperature.     

Blue and green upconversion luminescence modification of Tb<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript> co-doped Ca<Subscript>5</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>F inverse opal

Tb³⁺–Yb³⁺ co-doped Ca₅(PO₄)₃F inverse opal photonic crystals were prepared by a self-assembly technique in combination with a sol–gel method. Upconversion luminescence characteristics of the inverse opals were investigated. The results indicate that photonic band gap has a significant effect on upconversion luminescence of Tb³⁺–Yb³⁺ co-doped Ca₅(PO₄)₃F inverse opal. Significant inhibition of the green or blue upconversion luminescence was inspected if the photonic band gap overlapped with the emission band of Tb³⁺ ions.     

Sol–Gel Synthesis of Na<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> Glasses and their Characterization by NMR,SNMS, and AFM

Sodium aluminophosphate samples with composition 43.8Na₂O12.5Al₂O₃43.8P₂O₅ were prepared by the sol–gel route using different precursors and working in different pH ranges from pH < 1 up to pH > 10. The structures of the gels and of the corresponding glasses were investigated by solid state NMR and compared to that of a glass with the same composition prepared by a traditional melting process. In addition to bulk materials, thin films were deposited by dip coating on silica glasses. Applying secondary neutral mass spectrometry (SNMS), the expected elements and residual carbon were identified. The surfaces of the coatings and fracture surfaces of bulk material were investigated using atomic force microscopy (AFM). Solid state NMR revealed that samples prepared via a lactate route exhibited local Al and P environments closest to that of the melt-prepared glass, with the highest extent of Al-O-P connectivity.     

Sol–gel elaboration and structural investigations of Lu<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> planar waveguides

Europium actived Lu₂O₃ sol–gel transparent and crack free films were deposited by dipping on silica substrates. The film microstructure was studied by waveguide Raman spectroscopy (WRS) with annealing temperatures from 400 up to 1,000 °C and X-ray diffraction. The WRS results and TEM observations were correlated and showed that crystallization of the lutetium oxide phase into cubic phase occurs at 600 °C and is stable up to 1,000 °C, the crystallite size increasing between ±38 nm with annealing temperature ranging from 600 to 1,000 °C. Opto-geometrical parameters were determined by m-lines spectroscopy using four different wavelengths of laser sources in order to confirm the step-index profile of the as-prepared waveguides. The Eu³⁺ doped films heat-treated at 1,000 °C presented a constant thickness for the wavelengths 493, 543, 594 and 632.8 nm and a density of 8.4 g cm⁻³. High-resolution X-ray images were obtained.     

Preparation and activity evaluation of relative p–n junction photocatalyst Co-TiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript>

Co-TiO₂ photocatalyst was prepared by a sol–gel method using Co(NO₃)₂ · 6H₂O and tetrabutyl titanate [Ti(OC₄H₉)₄] as raw materials, and Co-TiO₂/TiO₂ photocatalyst was synthesized by mixing the Co-TiO₂ sol with TiO₂ sol. The Co-TiO₂/TiO₂ was characterized by X-ray powder diffraction, UV–Vis diffuse reflection spectrum, scanning electron microscopy, transmission electron microscopy, fluorescence spectra and X-ray photoelectron spectroscopy. The photocatalytic activity of the photocatalyst was evaluated by photocatalytic reduction of Cr₂O₇ ²⁻ and photocatalytic oxidation of methyl orange under UV irradiation. The results showed that, for the photocatalytic reduction of Cr₂O₇ ²⁻, the optimum percentage of Co-doped for the Co-TiO₂ was 0.5% (mole ratio of Co/Ti), and the optimum percentage of Co-TiO₂ for the Co-TiO₂/TiO₂ was 2.0% (mole ratio of Co-TiO₂/TiO₂). The photocatalytic reduction activities of the Co-TiO₂/TiO₂ and Co-TiO₂ are much higher than that of TiO₂. However, the photocatalytic oxidation activities of the Co-TiO₂/TiO₂ and Co-TiO₂ are much lower than that of TiO₂. Effects of heat treatment on the photocatalytic activities of the Co-TiO₂/TiO₂ and Co-TiO₂ were investigated. The mechanisms of influence on the photocatalytic activity were also discussed.     

Preparation of nanostructured thin films of yttrium aluminum garnet (Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>) by Sol—Gel technology

The synthesis of hydrolytically active heteroligand coordination compounds [M(C₅H₇O₂)_3–x(C₅H₁₁Oⁱ)_x] (where M = Al³⁺ and Y³⁺) using aluminum and yttrium acetylacetonates has been studied. The gel formation kinetics in their solutions upon hydrolysis and polycondensation has also been studied. Thin films of a solution of these precursors have been applied to polished sapphire substrates by dip coating. The crystallization of nanostructured yttrium aluminum garnet (Y₃Al₅O₁₂) films during heat treatment of xerogel coatings under various conditions has been studied. How the phase composition, microstructure, and particle size depend on the synthesis parameters has been recognized.