Preparation of Ultrafine and High Dispersion Pd/C Catalyst and Its Electrocatalytic Performance for Formic Acid Oxidation

A carbon supported Pd(Pd/C) catalyst used as the anodic catalyst in the direct formic acid fuel cells(DFAFC) was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate(EDTA) as stabilizer and complexing agent.This method is very simple.The average size of the Pd particles in the Pd/C catalyst prepared with the improved complex reduction method is as small as about 2.1 nm and the Pd particles in the Pd/C catalyst possess an excellent uniformity.The Pd/C catalyst shows a high electrocatalytic activity and stability for the formic acid oxidation.     

制备方法对PtMo/C催化剂上CO电催化氧化性能的影响

用化学还原法、胶体法和Adams法制备了PtMo/C电催化剂, 对其物理化学性质及其在CO电氧化反应中的催化性能进行了对比研究. TEM和XRD测试结果表明, 胶体法制备的催化剂颗粒在载体炭上均匀分布, 颗粒粒径约5 nm；由化学还原法制备的颗粒尺寸较大, 而Adams法制备的颗粒尺寸达数十纳米, 并有严重的团聚现象. CO消除伏安法测试结果表明, 三种制备方法中胶体法制备的PtMo/C催化剂具有最高的电化学表面积和电催化活性. 与常用的Pt/C催化剂相比, PtMo/C催化剂中Pt上弱吸附态CO的电氧化均得到了促进, 而强吸附态CO则不受影响. 这些结果表明PtMo颗粒的尺寸分布和在载体上的分散状况是影响PtMo/C催化剂电催化性能的主要因素. 胶体法制备的PtMo/C与常用的PtRu/C相比, 电化学表面积虽然较低, 但在低电势下CO的起始氧化电势只有0.15 V, 而且在0.15～0.5０ V之间发生电氧化的CO达到其总量的1/3.     

十五碳内酯的简易合成法

以中国西南地区的油料植物蒜头果油(Kernal oil),经皂化得到的二十四碳-15-烯酸为原料.通过臭氧化和硼氢化还原反应得到ω-羟基十五碳烷酸.以碳酸钾为催化剂,聚乙二醇为相转移催化剂使后者缩聚和解聚可以91%的得率制得十五碳内酯.在合成过程中,用正交试验和方差分析找出最佳实验条件.该大环内酯具有良好的定香作用.     

SBA-15介孔分子筛担载的钒基氧化物催化剂对乙烷选择氧化性能

用等体积浸渍法制备了SBA-15担载的钒基(V/SBA-15)和钾修饰的钒基氧化物(K-V/SBA-15)催化剂, 使用氮气吸附、小角X射线衍射(XRD)、紫外-可见漫反射光谱(UV-Vis DRS)和紫外激光拉曼光谱对这些催化剂的结构进行表征, 并评价了这些催化剂对乙烷选择氧化的活性与选择性. 实验结果表明介孔结构SBA-15对乙烷选择氧化的活性优于常规的SiO2; 对于SBA-15担载的V/SBA-15和K-V/SBA-15催化剂, 极低钒担载量(nV:nSi≤0.1:100)时隔离的四配位钒氧化物是乙烷选择氧化生成醛类化合物的活性物种, 高钒担载量(nV:nSi≥2.5:100)时聚合的和微晶态的钒氧化物是乙烷氧化脱氢或深度氧化的活性物种.     

Pd/C as Heterogeneous Catalyst for the Direct Arylation of (Poly)fluorobenzenes

The potential of the heterogeneous catalyst 10 % Pd/C in the direct arylation of (poly)fluorobenzene derivatives with aryl bromides has been investigated. In general, high yields of biaryl derivatives were obtained by using tri-, tetra-, and pentafluorobenzenes, whereas mono- and difluorobenzenes exhibited poor reactivity. The regioselectivities of the arylation reactions were similar to those observed with homogeneous palladium catalysts. Both electron-withdrawing and -donating substituents, such as nitrile, nitro, acetyl, ester, trifluoromethyl, tert-butyl, methoxy, or methyl, on the aryl bromide were tolerated. Unexpectedly, tetrafluoro-substituted [1,1′-biphenyl]-4-ols were obtained from pentafluorobenzene at 150 °C due to a formal regioselective hydroxylation, whereas at lower temperatures the expected pentafluorobiphenyls were obtained. However, no C−F bond cleavage was observed with the other polyfluorobenzene derivatives. These arylation reactions were carried out with only 1 mol % Pd/C as the catalyst and KOAc as an inexpensive base. Therefore, this protocol represents a very attractive access to (poly)fluoro-substituted biphenyls in terms of cost, simplicity, and sustainable chemistry because the Pd/C catalyst can be easily removed at the end of the reaction, there is no contamination with phosphine ligand residues, and the major side-product of the reaction is KOAc ⋅ HBr.     

PtZn-Sn/SBA-15合成、表征及对丙烷催化脱氢性能

以SBA-15为载体,利用浸渍法制备了单、双和三金属Pt催化剂,并对催化剂进行了N2物理吸附(BET)、程序升温还原(H2-TPR)、H2-化学吸附、透射电子显微镜(TEM)和O2-脉冲等技术表征,研究了它们对丙烷催化脱氢(CDH)制丙烯反应的催化性能。研究结果表明,Pt在三金属催化剂中的分散性能最好,并且部分负载组分可以进入SBA-15的孔道,Pt的分散度达到29%,Pt粒子尺寸为3 nm左右。三金属催化剂表现出优越的脱氢性能,这主要归结于载体的弱酸性、活性组分和助剂、载体之间的相互作用及Zn对Pt的电子调控作用。这些因素使催化剂的积炭量较低,因而具有较高的脱氢稳定性和极高的选择性。     

高温处理对碳载吡啶钴催化氧还原性能的影响

利用碳黑(Vulcan XC-72R) 中加入硫酸钴和吡啶(Py)作为催化剂前躯体, 经溶剂分散热处理构建了一类新型的高效氧还原CoPy/C复合催化剂. 运用循环伏安法和旋转圆盘电极(RDE)技术研究了不同温度(600~900 ℃)处理CoPy/C催化剂在碱性介质中对氧还原的电催化性能. 结果表明, 热处理能显著提高CoPy/C的催化活性, 活性次序为800 ℃>900 ℃>600 ℃>未处理. 其中800 ℃处理的15%Co25%Py/C(质量分数)复合催化剂表现出最佳的氧还原催化性能, 以其制备的气体扩散电极在3.0 mol/L KOH 电解质溶液(O₂气氛)中的半波电位为-0.069 V(相对于标准可逆氢电极), 起峰电位为0.026 V, 同时表现出明显的极限扩散电流. 利用透射电镜、 能谱分析和X射线衍射技术对催化剂的微观形貌、 颗粒大小和活性位结构的研究结果表明, 所制备的碳黑负载吡啶钴催化剂(15%Co25%Py/C)平均粒径为17 nm, 经800 ℃处理后吡啶结构发生了坍塌, 形成了其它价态的钴氧化合物、 硫化物和单质钴, 并协同吡啶中的氮对氧起催化还原作用. RDE结果表明, O₂在CoPy/C催化剂上的反应动力学主要通过4e^-过程还原成H₂O.     

Amberlyst-15催化C(sp~3)—H对靛红类化合物的加成反应

以Amberlyst-15为催化剂,甲基吡啶类化合物中的C(sp~3)—H键对靛红类化合物经加成反应合成了24个3-羟基-2-吲哚酮类化合物(3a~3x),其中3u~3x为新化合物,其结构经1H NMR,13C NMR,IR和HR-MS(ESI)表征。催化剂Amberlyst-15循环使用8次,不影响反应收率。     

Influence of the solvent and of the reaction concentration for palladium-catalysed direct arylation of heteroaromatics with 4-bromoacetophenone

The solvent is certainly one of the main sources of wastes during palladium-catalysed direct arylation reactions. We found that such direct arylations of heteroaromatics can be performed using very high concentrations of reactants (0.5 M–5 M). However, the Pd catalyst precursor used must be adapted to both the solvent nature and the concentration of reactants. The reactions performed in DMA, NMP or DMF can be carried out in very concentrated reaction mixtures using 0.1 mol% Pd(OAc)₂ catalyst without phosphine ligand. On the other hand, the reactions in CPME, pentan-1-ol or diethylcarbonate should be performed with a palladium catalyst associated with a phosphine ligand. These reaction conditions allow us to reduce the amount of wastes formed in the course of these couplings.     

Application of GO/COF as a novel,efficient and recoverable catalyst in the Knoevenagel reaction

Hybrid composite based on graphene oxide (GO) and covalent organic framework (COF) [GO/COF] was developed via a simple solvothermal method, at which GO was applied as a platform to load COF based on melamine and terephthaldehyde. The synthesized hybrid nanocomposite was characterized by FT-IR, XRD, EDX and SEM techniques. Morphological analyses carried out by SEM confirm the successful growth of COF over GO. Then, the resultant composite was employed as an amazing and cost-effective catalyst in the condensation of several aldehydes with malononitrile and produced the corresponding coupling products in high yields (up to 84%) at room temperature under solvent-free conditions with an amount of catalyst, 15 mg in a very short reaction time of 10 min. The catalyst could be reused without a noteworthy drop in catalytic activity at least eight times. The use of GO/COF catalyst outcomes under mild reaction conditions in very short reaction time, exceptional catalytic activity, high recyclability and an easy work-up process for the Knoevenagel condensation.     

Highly effective activation of aryl chlorides for Suzuki coupling in aqueous media using a ferrocene-based Pd(II)–diimine catalyst

The Suzuki coupling of aryl chlorides with boronic acids using a ferrocene-containing Pd(II)–diimine complex as catalyst, in aqueous media, under microwave heating is reported. A small amount of the catalyst (0.1%) was found to be highly effective for coupling unactivated aryl chlorides with boronic acids to form sterically hindered ortho-substituted biaryls. The same catalyst also enabled the coupling of aryl bromides and iodides with various boronic acids in very high yields. The catalyst is air stable and the catalytic reaction can be completed in 15 min.     

SBA-15负载有机金属钛(Ⅳ)催化剂合成纳米聚乙烯纤维

通过介孔分子筛SBA-15负载半夹心结构有机金属钛(Ⅳ)催化剂在一定的反应温度(20～80 ℃)和1 013 kPa乙烯压力下合成了纳米聚乙烯纤维。讨论并比较了负载剂和聚合条件对催化活性、聚合物分子量及聚合物形态的影响。相对于均相催化剂而言，催化活性有所降低，但聚合物分子量明显增大，达到10⁶数量级。在相同压力下，从低温到高温，聚乙烯形态也从细小纤维束逐渐变粗，更高温度熔成片状，80 ℃以上纤维状形态消失。这些表明，通过外部条件的选择可以得到合适的聚乙烯纤维。     

Contrast performance in catalytic ability—new cinchona phase transfer catalysts for asymmetric synthesis of α-amino acids

Two new cinchona phase transfer catalysts are prepared from dihydrocinchonidine using 13-picenylmethyl bromide and 1-pyrenylmethyl bromide, respectively. A total contrast in catalytic efficiency is observed during the asymmetric alkylation of glycinate esters; with one catalyst, the reaction is either incomplete or the enantioselectivity is very poor (15% ee) while the other catalyst afforded high selectivity up to 94% ee.     

锰助剂对Co／ZrO2超细催化剂F—T合成性能的影响

制备了以气凝胶超细ＺｒＯ２为载体的Ｃｏ／ＺｒＯ２及Ｃｏ－ＭＺｒＯ２催化剂；考察了Ｍｎ助剂对Ｃｏ／ＺｒＯ２催化剂结构、织构１还手、Ｈ２脱附及Ｆ－Ｔ合成性能的影响。结果表明，１５％Ｃｏ－４．７％Ｍｎ／ＺｒＯ２是合成重质烃（Ｃ２）的合适催化剂，每立方米合成气的Ｃ５收率可达１５０ｇ。     

Pd-Fe/C催化剂中Fe的状态对氧还原电催化活性的影响

直接甲醇燃料电池;Pd-Fe/C催化剂;氧还原;合金化     

Oxidation of cyclohexane with molecular oxygen using a Schiff base cobalt complex bonded to carbamate-modified silica gel

The Schiff base [1,2-bis(salicylidene amino)phenylene]cobalt(II) complex, chemically bonded to a carbamate-modified silica gel catalyst, has been prepared by a four step procedure. The oxidation of cyclohexane was studied in the presence of this catalyst under relatively mild conditions (150–200 °C, 15–20 atm) using molecular oxygen. The catalyst was found to be very selective for the production of cyclohexanol, with cyclohexanone formed in only a small amount (45:1). This is in contrast to the commercially available processes in which cyclohexanol and cyclohexanone are both formed in appreciable amounts. The t.g.a. analysis shows the catalyst to be stable up to 211 °C and atomic absorption spectroscopy indicated negligible metal loss during 50 h use of the catalyst up to 180 °C.     

CC Coupling of Ketones with Methanol Catalyzed by a N‐Heterocyclic Carbene–Phosphine Iridium Complex

An N‐heterocyclic carbene–phosphine iridium complex system was found to be a very efficient catalyst for the methylation of ketone via a hydrogen transfer reaction. Mild conditions together with low catalyst loading (1 mol %) were used for a tandem process which involves the dehydrogenation of methanol, C?C bond formation with a ketone, and hydrogenation of the new generated double bond by iridium hydride to give the alkylated product. Using this iridium catalyst system, a number of branched ketones were synthesized with good to excellent conversions and yields.     

无机胶体法制备Pt/C催化剂及其性能表征

采用无机胶体法制备用于质子交换膜燃料电池(PEMFC)的Pt/C催化剂。研究了影响PtO₂胶体生成和稳定性的因素(溶液的pH值、浓度和温度条件等)以及不同还原剂浓度对Pt/C催化剂性能的影响。透射电子显微镜测试结果表明，采用经优化的工艺条件所制备的Pt/C催化剂平均粒径为3 nm，且分散性好、粒度均匀。X-射线衍射分析表明，催化剂中Pt(111)晶面的相对含量较高，有利于加速氧还原反应。单体PEMFC的电压/电流密度曲线测试表明，所制备的Pt/C催化剂具有良好的电化学性能。     

Trans-ferulic acid valorization into stilbene derivatives via tandem decarboxylation/Heck coupling using Pd/Al-SBA-15 materials

Pd-containing Al-SBA-15 materials were prepared and characterized in view of their utilization in the two-step valorization of trans-ferulic acid into stilbenes via tandem decarboxylation/Mizoroki-Heck coupling. Materials were found to be highly active and selective in the proposed chemistries, with quantitative conversion to target products under mild reaction conditions (typically 100 °C, 3–6 h reaction). Relevant insights on catalyst deactivation via sintering (Pd nanoparticles agglomeration) were also observed for the synthesized materials.     

Porous organic polymer immobilized copper nanoparticles as heterogeneous catalyst for efficient benzylic C–H bond oxidation

A facile and practical heterogeneous copper nanoparticles catalyst (Cu@AEPOP) was prepared by the incorporation of Cu(OAc)₂ to amide and ether functionalized porous organic polymers (AEPOP) that were efficiently prepared by condensation of 4,4′-diaminodiphenyl ether with 1,3,5-benzenetricarbonyl chloride. The prepared AEPOP and Cu@AEPOP were characterized by SEM, BET, TEM, ICP, FT-IR and XRD. With TBHP (70 wt% in water) as oxidant and solvent, Cu@AEPOP showed excellent catalytic activity for the selective oxidation of benzylic C–H bonds. Among the oxidation of alkyl benzenes to ketones, secondary alcohols to ketones, and primary alcohols to acids, the copper catalyst exhibited remarkable selectivity and reactivity for a broad range of substrates in excellent yields. Furthermore, the experimental operation was very facile and the heterogeneous catalyst could be easily recovered by filtration separation.