Mercury forms and their transformation in pyrite under weathering

Pyrite is considered to be the major carrier of mercury in coal. Here, the chemical characteristics of two natural pyrite samples of different weathering degrees were characterized by time-of-flight secondary ion mass spectrometry (TOF-SIMS). Thermal stability of Hg was also analyzed via temperature programmed desorption experiment (TPD). Characteristic ions such as S⁻, Fe⁺, FeS⁻, and FeS₂⁻ were detected on the surface of fresh pyrite. The release temperature of Hg ranged between 180°C and 300°C, and the characteristic peak of black HgS was recorded. In addition, abundant Fe₂O₃⁻, FeSO⁻, SO₄⁻, and HSO₄⁻ were detected on the surface of weathered pyrite, and the release temperature of Hg therein was mainly distributed at 260°C to 380°C and 520°C to 600°C, corresponding to the characteristic peaks of red HgS and HgSO₄, respectively. The results show that pyrite is acidified during weathering and that Hg forms in pyrite are transformed from the original state (HgS) to HgSO₄.     

Catalytic oxidations of alcohols to carbonyl compounds by oxygen under solvent-free and transition-metal-free conditions

A green catalytic oxidation of alcohols to carbonyl compounds by oxygen was developed by using catalytic amounts of [bis(acetoxy)iodo]benzene/TEMPO/KNO₂. In addition, the use of a catalytic amount of poly[4-(bis(acetoxy)iodo)]styrene led to yields (up to 99%) comparable to the non-supported hypervalent iodine reagent, while offering the advantage of an efficient recovery and the subsequent recycling of the hypervalent iodine reagent.     

Electrochemical copolymerization of thiophene and aniline

In this study homopolymer, copolymer, and composites of aniline and thiophene were synthesized in nitrogen atmosphere by using TEATFB (Tetraethyl ammonium tetrafluoroborate) and Lithium perchlorate as supporting electrolytes. In order to analyze their structure and characteristics, IR spectrums of the samples were taken and thermogravimetric analysis (TGA) was applied. Also, the samples were photographed under scanning electron microscope (SEM) for microstructure analysis and their electrochemical properties were observed and conductivities were obtained by four probe method. Homopolymerization and copolymerization reactions were carried out in two different solvents viz. acetonitrile and benzonitrile in order to see the solvent effect on polymerization. However, changing the solvent was found to have no significant effect on the resulting properties. It was concluded that changing the supporting electrolyte caused a structural difference in the resulting homopolymer. It also affects the properties considerably. During the bilayer preparation changing the coating turn led to variations in the properties of the samples. When polythiophene (PT) was coated with polyaniline (PA), the resulting system was a composite. However, in coating PA with PT the system was identified to be a copolymer. © 1996 John Wiley & Sons, Inc.     

Factors affecting glycerol production byPichia farinosa under alkaline conditions

Glycerol is an important and valuable chemical that can be produced from renewable resources by fermentation. The desirable features of a successful process are high values of substrate conversions and high yields and concentrations of glycerol in the product broth, coupled with rapid fermentation cycles. Of the various osmophilic and nonosmophilic yeasts tested for their ability to produce glycerol in the presence and absence of steering agents (sodium sulfite or sodium carbonate), an osmophilic yeastPichia farinosa (ATCC 20210) was found to give attractive yields. Important variables influencing glycerol production by this strain under alkaline conditions using sodium carbonate have been investigated. A rapid fermentation (less than 120 h), coupled with high glycerol yields (45%), has been obtained.     

Enzymatic polymerization of aniline and phenol derivatives catalyzed by horseradish peroxidase in dioxane

Phenylenediamines, 4‐aminophenol and 1,4‐hydroquinone were polymerized via the catalysis of horseradish peroxidase in dioxane at ambient conditions by using hydrogen peroxide as the oxidant. Polymers formed in good yields are black powders soluble in dimethylformamide and dimethylsulfoxide. Several factors influencing the polymer yield were examined using 2‐phenylenediamine as substrate. It was found that pH value gave almost no influence in the range between 6.0 and 7.0, while the polymer yield increased as the concentration of the substrate in dioxane increased. The influence of the oxidant amount was still more obvious; larger excess of the oxidant being necessary in getting higher polymer yield. Using the optimized polymerization conditions, the yield of poly(2‐phenylenediamine) was achieved up to 77.8%. Weight average molecular weight of the polymers are higher than 1 × 10⁴ as determined by gel permeation chromatography. The structure of the polymers was characterized by using nuclear magnetic resonance and infrared techniques. Copyright © 2000 John Wiley & Sons, Ltd.     

Synthesis and biological evaluations of some Schiff-base esters of ferrocenyl aniline and simple aniline

The synthesis and biological studies of some long chain esters containing Schiff bases and their ferrocenyl analogues were carried out. The 4-amino ferrocene was prepared by the reported method. Long chain esters were synthesized by the condensation of different aliphatic acids with the corresponding aldehyde. The esters were then reacted with aniline as well as with 4-aminophenyl ferrocene to give corresponding Schiff bases. All the synthesized compounds were analyzed by elemental, FTIR and proton NMR studies, were also investigated for a range of biological activities. Determined by crown gall tumor inhibition assay. Antioxidant and DNA protective activities were determined by DPPH free radical scavenging assay and OH radical induced oxidative DNA damage assay, respectively. Among all test compounds, o-hydroxy-p-n-octadecanoyloxy-benzylidine-p-ferrocenyl aniline (FA2.1: a ferrocene containing Schiff base) showed highest antitumor, DPPH free radical scavenging and DNA protective activities.     

碳酸二甲酯和苯胺胺解反应产物的液相色谱分析

采用气-质联用仪对碳酸二甲酯和苯胺胺解反应合成苯氨基甲酸甲酯的反应体系的副产物N,N-二甲基苯胺进行定性分析,并提出了该反应体系主、副产物的液相色谱的分析方法,以硝基苯为内标物,实现了苯胺、苯氨基甲酸甲酯、N-甲基苯胺、二苯脲及N,N-二甲基苯胺的定量分析,实验结果表明,在一定浓度下,这5种组分与峰高线性良好,回收率在97．8％～102．7％,相对标准偏差小于2．01％。     

Characterisation of the oxidation products of pyrite by Thermogravimetric and Evolved Gas analysis

Museum specimens of pyrite are known to undergo oxidation even during storage. Characterisation of the oxidation products is however not always simple due to amorphous character and varying degrees of hydration of the oxidation products. This paper presents an alternative approach to the characterisation of oxidation products by identifying their presence from their characteristic thermal decomposition processes using thermogravimetric and evolved gas analysis. Four pyrite specimens were characterised with varying degrees of oxidation. Iron(II) and iron(III) sulphates were also characterised for comparative purposes. The degradation products were observed to correlate well with the presence of iron(II) sulphate even though there was found to be some discrepancy in the higher temperature decomposition reactions. This revised version was published online in July 2006 with corrections to the Cover Date.     

苯胺在碳纳米管上的吸附特征

苯胺是一种重要的有机化工原料,能通过皮肤和呼吸道进入人体而引起中毒,还会严重污染环境。目前,国内外处理含苯胺废水的方法主要有氧化法、萃取法、生化法、吸附法等。本文使用碳纳米管进行液相吸附除去苯胺。     

液相色谱-串联质谱法快速测定水及鱼肉中的苯胺

为快速准确测定水及鱼肉中的苯胺,采用乙腈提取、高效液相色谱-串联质谱测定,建立了水及鱼肉中苯胺的快速测定方法。水样与乙腈以4：1的体积比混合,1.00 g鱼肉中加入2.00 mL乙腈,涡旋提取1 min,水样和鱼肉样品的提取液离心5 min后取上清液测定。以C₁₈柱为分离柱,乙腈-0.5%（v/v）甲酸水溶液（85：15,v/v）为流动相,目标物质在3 min内分离。在0.5~500 μg/L范围内,苯胺峰面积与内标峰面积之比与质量浓度的线性关系良好（R²>0.999）。基质加标试验结果表明,苯胺在水中的回收率分别为93.7%（加标水平为40 ng）和86.7% （加标水平为400 ng）,苯胺在鱼肉中的回收率分别为96.8%、 92.6%和81.8%（加标水平分别为5、50和500 ng）,相对标准偏差在1.5%~9.2%之间。水样和鱼肉样品中苯胺的检出限分别为0.50 μg/L和1.00 μg/kg,定量限分别为1.00 μg/L和2.00 μg/kg。应用该方法测定了从受苯胺污染的水库中采集的13份水样和12份鱼肉样品,结果表明,水和鱼肉中苯胺的最大含量分别为1943.6 μg/L和60.8 μg/kg。本方法快速、准确,适用于水和鱼肉中苯胺的快速测定。     

Acidity and aniline alkylation activity of mixed Fe-Al pillared montmorillonites

Al-pillared, Fe-pillared and mixed Fe-Al pillared systems have been prepared and characterized using EDX and XRD analyses, surface area pore volume and acidity measurements. Mixed systems are found to be superior to single oxide pillared systems in terms of acidity and aniline methylation activity. This revised version was published online in June 2006 with corrections to the Cover Date.     

原位氮掺杂活性血炭对苯胺吸附性能研究

以猪血粉为原料,磷酸为活化剂,用化学活化法制备原位氮掺杂活性炭(BN-AC),并用于苯胺的吸附.采用元素分析、FTIR、XPS等分析方法研究了BN-AC的理化性质.分析结果表明BN-AC比表面积为461.0 m2·g-1,总孔容为0.3 cm3·g-1.BN-AC表面含有吡啶氮、吡咯氮和石墨氮,成功地保留了血粉中的N成...     

Temperature-dependent behavior of immobilized alkaline phosphatase. I. Role of working conditions and pH during coupling

Alkaline phosphatase from hog intestine was immobilized to controlled-pore glass under various conditions. The specific activity of the enzyme was not diminished by immobilization. The influence of temperature and pH on the behavior and the stability of the immobilized enzyme preparations is discussed and compared to that of the native enzyme.     

(N‐Salicylidene)aniline Derived Schiff Base Complexes of Methyltrioxorhenium(VII): Ligand Influence and Catalytic Performance

It′s a fine line : Methyltrioxorhenium(VII) (MTO) readily forms 1:1 adducts with several N‐(salicylidene)aniline derived Schiff bases. Steric and electronic effects of the ligands play a major role when it comes to stability and catalytic activity. Good donors on the Schiff base ligands, in general, lead to shorter Re? O(Schiff base) bridges and lower catalytic activity, while it is the opposite for acceptor ligands on the Schiff bases.

     

Cu-mediated selective bromination of aniline derivatives and preliminary mechanism study

A simple and efficient bromination of aniline, aniline derivatives, and analogs have been developed. Forty three examples were given and the highest yield reached was 98%. Different substrates including substituted aniline, pyridin-amine, N-substituted aniline, N,N-disubstituted aniline, N-phenyl-amide, N-phenyl-sulfonamide, and nitrogen-containing heterocycles were all reactive and selectively generated desired bromo-products. The method can be applied to synthesize drug intermediate and quinoxaline derivatives.     

Catalytic and electrocatalytic oxidation of aniline to nitrobenzene over vanadium silicate molecular sieves: VS-1 usingt-butyl hydroperoxide (TBHP) as oxidant

A comparison of the results of catalytic and electrocatalytic oxidation of aniline using VS-1 in the presence of H₂O₂ and TBHP indicates remarkable differences in conversion and selectivity. VS-1 catalyzes the oxidation of aniline selectively to nitrobenzene (73%) in the presence oft-butyl hydroperoxide (TBHP), while azoxybenzene (95.2%) is formed selectively when H₂O₂ is used. Cyclic voltammetric studies show a three-step oxidation of aniline to nitrobenzene in H₂O₂ but in the presence of TBHP only one step is observed. Electrocatalytic oxidation of aniline to nitrobenzene occurs at a potential 700 mV less than that corresponding to H₂O₂ as oxidant along with a selectivity of 91.8%. The enhancement of electrocatalytic rate is attributed to the stabilization of electron deficient transition state.     

Plasticization of a poly(ethyl acrylate) ionomer by an alkyl aniline

The plasticization by 4-decylaniline (4DA) of a microphase-separated poly(ethyl acrylate) ionomer containing sodium carboxylate groups is examined. Dynamic mechanical thermal analysis, supplemented by differential scanning calorimetry, shows that the matrix and cluster glass transitions (T_g's) in the ionomer are both depressed by ca. 1°C/wt % 4DA; this, in turn, is similar to the T_g depression in the blend of the parent poly(ethyl acrylate) (PEA) with 4DA. There is no evidence of 4DA crystallinity in the blend. Small-angle x-ray scattering (SAXS) measurements show that the ionomer peak increases in intensity and decreases in scattering angle with increasing concentration of 4DA in the blend; the corresponding Bragg spacing, initially at 2.3 nm, increases by ca. 0.04 nm/wt % 4DA. These results, supported by preliminary spectroscopic measurements, are attributed to hydrogen bonding interactions between the amine groups of 4DA and the ester groups in PEA and the ionomer, rendering the blend miscible. It is argued that the uniform distribution of 4DA throughout the material plasticizes both phases of the ionomer by adding free volume; this also accounts for the increase in the characteristic spacing detected by SAXS.     

Synthesis and characterization of electroactive copolymer with phenyl-capped aniline tetramer in the main chain by oxidative coupling polymerization

A novel electroactive alternating copolymer, with fixed conjugated length of oligoaniline (phenyl-capped aniline tetramer) in the main chain, was successfully synthesized via oxidative coupling polymerization. The structure of the copolymer was systematically studied by Fourier-transform infrared (FTIR) spectra, NMR, elemental analysis (EA), UV-vis spectra and X-ray powder diffraction (XRD). And its electrochemical behavior was studied by cyclic voltammetry (CV) measurement. It was found that the obtained copolymer bearing phenyl-capped aniline tetramer segments had a reversible electrochemical property in the cyclic voltammetry, and the copolymer was oxidized to its emeraldine oxidation state and then to the pernigraniline oxidation state, which was same as that of polyaniline. Moreover, the thermal properties of the copolymer were evaluated by thermogravimetric analysis (TGA). The electrical conductivity of the obtained copolymer was about 1.43 × 10⁻⁷ S cm⁻¹ at room temperature.     

(NH4)IrCl6 and other promoting agents of the chemical polymerization of aniline

It has been found that some transition metal salts considerably decrease the induction period of the chemical polymerization of aniline. The efficiency of the promoting agents decreases in the series (N)₂IrQ₆> MoCl₅>NiCl₂.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1500–1502, August, 1994.     

Fluorescence enhancing by alkaline degradation of tetracycline antibiotics and its application

Tetracycline antibiotics could be degraded after being beated in boiling-water bath in alkaline solution (in KOH medium).The fluorescence excitation and emission wavelengths of the degradation products changed and the fluorescence intensity increased by 5-190 folds as compared with that of antibiotics themselves It was considered that there occurred a nucleophilic ring rupture reaction to form the degradation products with lactome structure The mteraction of the lone pair electrons of oxygen on the degradation products with the conjugated π electrons induced the in crease of the delocalization for the conjugated electron system in the molecule and thus enhanced the fluorescence intensity.