High‐Entropy Layered Oxide Cathodes for Sodium‐Ion Batteries

Material innovation on high‐performance Na‐ion cathodes and the corresponding understanding of structural chemistry still remain a challenge. Herein, we report a new concept of high‐entropy strategy to design layered oxide cathodes for Na‐ion batteries. An example of layered O3‐type NaNi_0.12Cu_0.12Mg_0.12Fe_0.15Co_0.15Mn_0.1Ti_0.1Sn_0.1Sb_0.04O₂ has been demonstrated, which exhibits the longer cycling stability (ca. 83 % of capacity retention after 500 cycles) and the outstanding rate capability (ca. 80 % of capacity retention at the rate of 5.0 C). A highly reversible phase‐transition behavior between O3 and P3 structures occurs during the charge‐discharge process, and importantly, this behavior is delayed with more than 60 % of the total capacity being stored in O3‐type region. Possible mechanism can be attributed to the multiple transition‐metal components in this high‐entropy material which can accommodate the changes of local interactions during Na⁺ (de)intercalation. This strategy opens new insights into the development of advanced cathode materials.     

Realizing Complete Solid-Solution Reaction in High Sodium Content P2-Type Cathode for High-Performance Sodium-Ion Batteries

P2-type layered oxides suffer from an ordered Na⁺/vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na⁺ extraction/insertion. The deficient sodium in the P2-type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na⁺ de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2-type layered oxides. To address these challenges, a novel high sodium content (0.85) and plateau-free P2-type cathode-Na_0.85Li_0.12Ni_0.22Mn_0.66O₂ (P2-NLNMO) was developed. The complete solid-solution reaction over a wide voltage range ensures both fast Na⁺ mobility (10⁻¹¹ to 10⁻¹⁰ cm² s⁻¹) and small volume variation (1.7 %). The high sodium content P2-NLNMO exhibits a higher reversible capacity of 123.4 mA h g⁻¹, superior rate capability of 79.3 mA h g⁻¹ at 20 C, and 85.4 % capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid-solution reaction are critical to realizing high-performance P2-type cathodes for sodium-ion batteries.     

Realizing Complete Solid‐Solution Reaction in High Sodium Content P2‐Type Cathode for High‐Performance Sodium‐Ion Batteries

P2‐type layered oxides suffer from an ordered Na⁺/vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na⁺ extraction/insertion. The deficient sodium in the P2‐type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na⁺ de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2‐type layered oxides. To address these challenges, a novel high sodium content (0.85) and plateau‐free P2‐type cathode‐Na_0.85Li_0.12Ni_0.22Mn_0.66O₂ (P2‐NLNMO) was developed. The complete solid‐solution reaction over a wide voltage range ensures both fast Na⁺ mobility (10^?11 to 10^?10 cm² s^?1) and small volume variation (1.7 %). The high sodium content P2‐NLNMO exhibits a higher reversible capacity of 123.4 mA h g^?1, superior rate capability of 79.3 mA h g^?1 at 20 C, and 85.4 % capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid‐solution reaction are critical to realizing high‐performance P2‐type cathodes for sodium‐ion batteries.     

One-Step Calcination Synthesis of Bulk-Doped Surface-Modified Ni-Rich Cathodes with Superlattice for Long-Cycling Li-Ion Batteries

Nickel-rich (Ni≥90 %) layered cathodes are critical materials for achieving higher-energy-density and lower-cost next-generation Li-ion batteries (LIBs). However, their bulk and interface structural instabilities significantly impair their electrochemical performance, thus hindering their widespread adoption in commercial LIBs. Exploiting Ti and Mo diffusion chemistry, we report one-step calcination to synthesize bulk-to-surface modified LiNi_0.9Co_0.09Mo_0.01O₂ (NCMo90) featuring a 5 nm Li₂TiO₃ coating on the surface, a Mo-rich Li⁺/Ni²⁺ superlattice at the sub-surface, and Ti-doping in the bulk. Such a multi-functional structure effectively maintains its structural integrity upon cycling. As a result, such NCMo90 exhibits a high initial capacity of 221 mAh g⁻¹ at 0.1 C, excellent rate performance (184 mAh g⁻¹ at 5 C), and high capacity retention of 94.0 % after 500 cycles. This work opens a new avenue to developing industry-applicable Ni-rich cathodes for next-generation LIBs.     

In situ Interweaved Binder Framework Mitigating the Structural and Interphasial Degradations of High-nickel Cathodes in Lithium-ion Batteries

The practical viability of high-nickel layered oxide cathodes is compromised by the interphasial and structural degradations. Herein, we demonstrate that by applying an in situ interweaved binder, the cycling stability of high-nickel cathodes can be significantly improved. Specifically, the results show that the resilient binder network immobilizes the transition-metal ions, suppresses electrolyte oxidative decomposition, and mitigates cathode particles pulverization, thus resulting in suppressed cathode-to-anode chemical crossover and ameliorated chemistry and architecture of electrode-electrolyte interphases. Pouch full cells with high-mass-loading LiNi_0.8Mn_0.1Co_0.1O₂ cathodes achieve 0.02 % capacity decay per cycle at 1 C rate over 1 000 deep cycles at 4.4 V (vs. graphite). This work demonstrates a rational structural and compositional design strategy of polymer binders to mitigate the structural and interphasial degradations of high-Ni cathodes in lithium-ion batteries.     

Combustion-synthesized sodium manganese (cobalt) oxides as cathodes for sodium ion batteries

We report on the electrochemical properties of layered manganese oxides, with and without cobalt substituents, as cathodes in sodium ion batteries. We fabricated sub-micrometre-sized particles of Na_0.7MnO_2?+?z and Na_0.7Co_0.11Mn_0.89O_2?+?z via combustion synthesis. X-ray diffraction revealed the same layered hexagonal P2-type bronze structure with high crystallinity for both materials. Potentiostatic and galvanostatic charge/discharge cycles in the range 1.5–3.8 V vs. Na | Na⁺ were performed to identify potential-dependent phase transitions, capacity, and capacity retention. After charging to 3.8 V, both materials had an initial discharge capacity of 138 mA?h?g^?1 at a rate of 0.3 C. For the 20th cycle, those values reduced to 75 and 92 mA?h?g^?1 for Co-free and Co-doped samples, respectively. Our findings indicate that earlier works probably underestimated the potential of (doped) P2-type Na_0.7MnO_2?+?z as cathode material for sodium ion batteries in terms of capacity and cycle stability. Apart from doping, a simple optimization parameter seems to be the particle size of the active material.     

An Ultrastable Anode for Long‐Life Room‐Temperature Sodium‐Ion Batteries

Sodium‐ion batteries are important alternative energy storage devices that have recently come again into focus for the development of large‐scale energy storage devices because sodium is an abundant and low‐cost material. However, the development of electrode materials with long‐term stability has remained a great challenge. A novel negative‐electrode material, a P2‐type layered oxide with the chemical composition Na_2/3Co_1/3Ti_2/3O₂, exhibits outstanding cycle stability (ca. 84.84 % capacity retention for 3000 cycles, very small decrease in the volume (0.046 %) after 500 cycles), good rate capability (ca. 41 % capacity retention at a discharge/charge rate of 10 C), and a usable reversible capacity of about 90 mAh g^?1 with a safe average storage voltage of approximately 0.7 V in the sodium half‐cell. This P2‐type layered oxide is a promising anode material for sodium‐ion batteries with a long cycle life and should greatly promote the development of room‐temperature sodium‐ion batteries.     

An Abnormal 3.7 Volt O3‐Type Sodium‐Ion Battery Cathode

Layered O3‐type sodium oxides (NaMO₂, M=transition metal) commonly exhibit an O3–P3 phase transition, which occurs at a low redox voltage of about 3 V (vs. Na⁺/Na) during sodium extraction and insertion, with the result that almost 50 % of their total capacity lies at this low voltage region, and they possess insufficient energy density as cathode materials for sodium‐ion batteries (NIBs). Therefore, development of high‐voltage O3‐type cathodes remains challenging because it is difficult to raise the phase‐transition voltage by reasonable structure modulation. A new example of O3‐type sodium insertion materials is presented for use in NIBs. The designed O3‐type Na_0.7Ni_0.35Sn_0.65O₂ material displays a highest redox potential of 3.7 V (vs. Na⁺/Na) among the reported O3‐type materials based on the Ni²⁺/Ni³⁺ couple, by virtue of its increased Ni?O bond ionicity through reduced orbital overlap between transition metals and oxygen within the MO₂ slabs. This study provides an orbital‐level understanding of the operating potentials of the nominal redox couples for O3‐NaMO₂ cathodes. The strategy described could be used to tailor electrodes for improved performance.     

Co-Intercalation of Dual Charge Carriers in Metal-Ion-Confining Layered Vanadium Oxide Nanobelts for Aqueous Zinc-Ion Batteries

Vanadium-based oxides with high theoretical specific capacities and open crystal structures are promising cathodes for aqueous zinc-ion batteries (AZIBs). In this work, the confined synthesis can insert metal ions into the interlayer spacing of layered vanadium oxide nanobelts without changing the original morphology. Furthermore, we obtain a series of nanomaterials based on metal-confined nanobelts, and describe the effect of interlayer spacing on the electrochemical performance. The electrochemical properties of the obtained Al_2.65V₆O₁₃ ⋅ 2.07H₂O as cathodes for AZIBs are remarkably improved with a high initial capacity of 571.7 mAh ⋅ g⁻¹ at 1.0 A g⁻¹. Even at a high current density of 5.0 A g⁻¹, the initial capacity can still reach 205.7 mAh g⁻¹, with a high capacity retention of 89.2 % after 2000 cycles. This study demonstrates that nanobelts confined with metal ions can significantly improve energy storage applications, revealing new avenues for enhancing the electrochemical performance of AZIBs.     

Lithium Nitrate Regulated Sulfone Electrolytes for Lithium Metal Batteries

The electrolytes in lithium metal batteries have to be compatible with both lithium metal anodes and high voltage cathodes, and can be regulated by manipulating the solvation structure. Herein, to enhance the electrolyte stability, lithium nitrate (LiNO₃) and 1,1,2,2-tetrafuoroethyl-2′,2′,2′-trifuoroethyl(HFE) are introduced into the high-concentration sulfolane electrolyte to suppress Li dendrite growth and achieve a high Coulombic efficiency of >99 % for both the Li anode and LiNi_0.8Mn_0.1Co_0.1O₂ (NMC811) cathodes. Molecular dynamics simulations show that NO₃⁻ participates in the solvation sheath of lithium ions enabling more bis(trifluoromethanesulfonyl)imide anion (TFSI⁻) to coordinate with Li⁺ ions. Therefore, a robust LiN_xO_y−LiF-rich solid electrolyte interface (SEI) is formed on the Li surface, suppressing Li dendrite growth. The LiNO₃-containing sulfolane electrolyte can also support the highly aggressive LiNi_0.8Mn_0.1Co_0.1O₂ (NMC811) cathode, delivering a discharge capacity of 190.4 mAh g⁻¹ at 0.5 C for 200 cycles with a capacity retention rate of 99.5 %.     

Li2MnO3 content effects on thermal,structural, electrical and electrochemical properties of xLi2MnO3-(1-x)LiNi0.9Zn0.1O2 cathode materials

xLi₂MnO₃-(1-x)LiNi_0.9Zn_0.1O₂ (x = 0.1, 0.2 and 0.3) cathodes were prepared by two steps solid-state reaction method. Layered crystalline phases (space groups of C2/m for Li₂MnO₃ and R3m for LiNi_0.9Zn_0.1O₂) were detected in all cathodes. FTIR study also revealed the formation of the layered-type structures of all cathodes. The structural parameters were greatly influenced by the contents of Li₂MnO₃ in xLi₂MnO₃-(1-x)LiNi_0.9Zn_0.1O₂. The electrical conductivities were found in the range of 1.2 × 10^?6 to 2.7 × 10^?6 S/cm. The dielectric spectra revealed the interfacial polarization Maxwell–Wagner type dielectric dispersion existing in all samples. The cathodes delivered the discharge capacities of 149 (x = 0.1), 151 (x = 0.2) and 157 mAh/g (x = 0.3) with capacity retention between 94.6 and 96.8% when they were cycled from 3.0 to 4.5 V under 0.1C rate. The x = 0.3 cathode exhibited the highest cyclic performance (96.8%) after 10 cycles due to its lower cations disorder.     

Manipulating Layered P2@P3 Integrated Spinel Structure Evolution for High-Performance Sodium-Ion Batteries

Structural evolution of the cathode during cycling plays a vital role in the electrochemical performance of sodium-ion batteries. A strategy based on engineering the crystal structure coupled with chemical substitution led to the design of the layered P2@P3 integrated spinel oxide cathode Na_0.5Ni_0.1Co_0.15Mn_0.65Mg_0.1O₂, which shows excellent sodium-ion half/full battery performance. Combined analyses involving scanning transmission electron microscopy with atomic resolution as well as in situ synchrotron-based X-ray absorption spectra and in situ synchrotron-based X-ray diffraction patterns led to visualization of the inherent layered P2@P3 integrated spinel structure, charge compensation mechanism, structural evolution, and phase transition. This study provides an in-depth understanding of the structure-performance relationship in this structure and opens up a novel field based on manipulating structural evolution for the design of high-performance battery cathodes.     

铁基普鲁士蓝正极材料的宏量制备及电化学储钠性能

以柠檬酸钠作为配位剂,采用共沉淀法,在室温下制备了铁基普鲁士蓝材料(FePB).当使用20 L容积的反应釜,并将前驱体亚铁氰化钠(Na4[Fe(CN)6])的浓度提高至0.5 mol·L-1时,制备一次可实现高达500 g的产量.电化学测试显示,所得FePB材料具有较高的容量、优异的倍率性能和良好的循环寿命.在0.1C...     

A Practical High-Energy Cathode for Sodium-Ion Batteries Based on Uniform P2-Na0.7CoO2 Microspheres

Layered metal oxides have attracted increasing attention as cathode materials for sodium-ion batteries (SIBs). However, the application of such cathode materials is still hindered by their poor rate capability and cycling stability. Here, a facile self-templated strategy is developed to synthesize uniform P2-Na_0.7CoO₂ microspheres. Due to the unique microsphere structure, the contact area of the active material with electrolyte is minimized. As expected, the P2-Na_0.7CoO₂ microspheres exhibit enhanced electrochemical performance for sodium storage in terms of high reversible capacity (125 mAh g⁻¹ at 5 mA g⁻¹), superior rate capability and long cycle life (86 % capacity retention over 300 cycles). Importantly, the synthesis method can be easily extended to synthesize other layered metal oxide (P2-Na_0.7MnO₂ and O3-NaFeO₂) microspheres.     

Mitigation of Jahn–Teller distortion and Na+/vacancy ordering in a distorted manganese oxide cathode material by Li substitution

Layered manganese-based oxides are promising candidates as cathode materials for sodium-ion batteries (SIBs) due to their low cost and high specific capacity. However, the Jahn–Teller distortion from high-spin Mn³⁺ induces detrimental lattice strain and severe structural degradation during sodiation and desodiation. Herein, lithium is introduced to partially substitute manganese ions to form distorted P′2-Na_0.67Li_0.05Mn_0.95O₂, which leads to restrained anisotropic change of Mn–O bond lengths and reinforced bond strength in the [MnO₆] octahedra by mitigation of Jahn–Teller distortion and contraction of MnO₂ layers. This ensures the structural stability during charge and discharge of P′2-Na_0.67Li_0.05Mn_0.95O₂ and Na⁺/vacancy disordering for facile Na⁺ diffusion in the Na layers with a low activation energy barrier of ∼0.53 eV. It exhibits a high specific capacity of 192.2 mA h g⁻¹, good cycling stability (90.3% capacity retention after 100 cycles) and superior rate capability (118.5 mA h g⁻¹ at 1.0 A g⁻¹), as well as smooth charge/discharge profiles. This strategy is effective to tune the crystal structure of layered oxide cathodes for SIBs with high performance.

Li-Substitution in P′2-Na_0.67MnO₂ mitigates the anisotropic change of Mn–O bonds and Na/vacancy ordering, and hence significantly promotes its cycling stability and rate capability as a cathode material for sodium-ion batteries.     

Manipulating Layered P2@P3 Integrated Spinel Structure Evolution for High‐Performance Sodium‐Ion Batteries

Structural evolution of the cathode during cycling plays a vital role in the electrochemical performance of sodium‐ion batteries. A strategy based on engineering the crystal structure coupled with chemical substitution led to the design of the layered P2@P3 integrated spinel oxide cathode Na_0.5Ni_0.1Co_0.15Mn_0.65Mg_0.1O₂, which shows excellent sodium‐ion half/full battery performance. Combined analyses involving scanning transmission electron microscopy with atomic resolution as well as in situ synchrotron‐based X‐ray absorption spectra and in situ synchrotron‐based X‐ray diffraction patterns led to visualization of the inherent layered P2@P3 integrated spinel structure, charge compensation mechanism, structural evolution, and phase transition. This study provides an in‐depth understanding of the structure‐performance relationship in this structure and opens up a novel field based on manipulating structural evolution for the design of high‐performance battery cathodes.     

Preparation and Electrochemical Performance of Li[Ni1/3Co1/3Mn1/3]O2 Synthesized Using Li2CO3 as Template

Porous structure Li[Ni_1/3Co_1/3Mn_1/3]O₂ has been synthesized via a facile carbonate co‐precipitation method using Li₂CO₃ as template and lithium‐source. The physical and electrochemical properties of the materials were examined by many characterizations including TGA, XRD, SEM, EDS, TEM, BET, CV, EIS and galvanostatic charge‐discharge cycling. The results indicate that the as‐synthesized materials by this novel method own a well‐ordered layered structure α‐NaFeO₂ [space group: R‐3m(166)], porous morphology, and an average primary particle size of about 150 nm. The porous material exhibits larger specific surface area and delivers a high initial capacity of 169.9 mAh·g^?1 at 0.1 C (1 C=180 mA·g^?1) between 2.7 and 4.3 V, and 126.4, 115.7 mAh·g^?1 are still respectively reached at high rate of 10 C and 20 C. After 100 charge‐discharge cycles at 1 C, the capacity retention is 93.3%, indicating the excellent cycling stability.     

The Universal Super Cation-Conductivity in Multiple-cation Mixed Chloride Solid-State Electrolytes

As exciting candidates for next-generation energy storage, all-solid-state lithium batteries (ASSLBs) are highly dependent on advanced solid-state electrolytes (SSEs). Here, using cost-effective LaCl₃ and CeCl₃ lattice (UCl₃-type structure) as the host and further combined with a multiple-cation mixed strategy, we report a series of UCl₃-type SSEs with high room-temperature ionic conductivities over 10⁻³ S cm⁻¹ and good compatibility with high-voltage oxide cathodes. The intrinsic large-size hexagonal one-dimensional channels and highly disordered amorphous phase induced by multi-metal cation species are believed to trigger fast multiple ionic conductions of Li⁺, Na⁺, K⁺, Cu⁺, and Ag⁺. The UCl₃-type SSEs enable a stable prototype ASSLB capable of over 3000 cycles and high reversibility at −30 °C. Further exploration of the brand-new multiple-cation mixed chlorides is likely to lead to the development of advanced halide SSEs suitable for ASSLBs with high energy density.     

Scalable Synthesis of One-Dimensional Mesoporous ZnMnO3 Nanorods with Ultra-Stable and High Rate Capability for Efficient Lithium Storage

The cost-efficient ZnMnO₃ has attracted increasing attention as a prospective anode candidate for advanced lithium-ion batteries (LIBs) owing to its resourceful abundance, large lithium storage capacity and low operating voltage. However, its practical application is still seriously limited by the modest cycling and rate performances. Herein, a facile design to scalable synthesize unique one-dimensional (1D) mesoporous ZnMnO₃ nanorods (ZMO-NRs) composed of nanoscale particles (≈11 nm) is reported. The 1D mesoporous structure and nanoscale building blocks of the ZMO-NRs effectively promote the transport of ions/electrons, accommodate severe volume changes, and expose more active sites for lithium storage. Benefiting from these appealing structural merits, the obtained ZMO-NRs anode exhibits excellent rate behavior (≈454 mAh g⁻¹ at 2 A g⁻¹) and ultra-long term cyclic performance (≈949.7 mAh g⁻¹ even over 500 cycles at 0.5 A g⁻¹) for efficient lithium storage. Additionally, the LiNi_0.8Co_0.1Mn_0.1O₂//ZMO-NRs full cell presents a practical energy density (≈192.2 Wh kg⁻¹) and impressive cyclability with approximately 91 % capacity retention over 110 cycles. This highlights that the ZMO-NRs product is a highly promising high-rate and stable electrode candidate towards advanced LIBs in electronic devices and sustainable energy storage applications.     

A High‐Voltage and Ultralong‐Life Sodium Full Cell for Stationary Energy Storage

Recently, there has been great interest in developing advanced sodium‐ion batteries for large‐scale application. Most efforts have concentrated on the search for high‐performance electrode materials only in sodium half‐cells. Research on sodium full cells for practical application has encountered many problems, such as insufficient cycles with rapid capacity decay, low safety, and low operating voltage. Herein, we present a layered P2‐Na_0.66Ni_0.17Co_0.17Ti_0.66O₂, as both an anode (ca. 0.69 V versus Na⁺/Na) and as a high‐voltage cathode (ca. 3.74 V versus Na⁺/Na). The full cell based on this bipolar electrode exhibits well‐defined voltage plateaus near 3.10 V, which is the highest average voltage in the symmetric cells. It also shows the longest cycle life (75.9 % capacity retention after 1000 cycles) in all sodium full cells, a usable capacity of 92 mAh g^?1, and superior rate capability (65 mAh g^?1 at a high rate of 2C).