B‐MWW Zeolite: The Case Against Single‐Site Catalysis

Boron‐containing materials have recently been identified as highly selective catalysts for the oxidative dehydrogenation (ODH) of alkanes to olefins. It has previously been demonstrated by several spectroscopic characterization techniques that the surface of these boron‐containing ODH catalysts oxidize and hydrolyze under reaction conditions, forming an amorphous B₂(OH)_xO_(3?x/2) (x=0–6) layer. Yet, the precise nature of the active site(s) remains elusive. In this Communication, we provide a detailed characterization of zeolite MCM‐22 isomorphously substituted with boron (B‐MWW). Using ¹¹B solid‐state NMR spectroscopy, we show that the majority of boron species in B‐MWW exist as isolated BO₃ units, fully incorporated into the zeolite framework. However, this material shows no catalytic activity for ODH of propane to propene. The catalytic inactivity of B‐MWW for ODH of propane falsifies the hypothesis that site‐isolated BO₃ units are the active site in boron‐based catalysts. This observation is at odds with other traditionally studied catalysts like vanadium‐based catalysts and provides an important piece of the mechanistic puzzle.     

丙烷氧化脱氢不同硅基载体负载钒氧化物催化剂的TPSR表征

研究了钒负载不同氧化硅载体(Silica-gel,SBA-15,MCM-41,fumed-SiO2,Nano-SiO2)的丙烷氧化脱氢(ODH)催化剂的结构特征和催化性能,结合催化剂的程序升温表面反应(TPSR)的差热热重质谱(TG-DSC-MS)和原位紫外漫反射光谱(UV-vis DRS)等技术,研究钒在载体上的分散度和晶格氧的反应性。结果表明:负载型钒氧化物催化剂的活性取决于钒在不同硅基载体上的分散度,高度分散的隔离的四配位V5+是丙烷氧化脱氢的活性位。C3H6选择性主要与催化剂的平均孔径相关联,平均孔径越小,产物C3H6越易发生深度氧化。另外,不同氧化硅载体晶格氧与钒的结合强度对C3H6的选择性也产生影响,结合力较弱的V-O-Si中的晶格氧是丙烷氧化脱氢的燃烧位,且燃烧温度随晶格氧与钒、硅结合强度的减小而降低。而与钒结合力较强的V=O和V-O-V中的晶格氧是丙烷氧化脱氢的选择氧化位。硅基载体形貌和结构的不同导致负载型钒氧化物催化剂丙烷氧化脱氢活性和选择性发生差异。     

SBA-15 负载 β-Mg2V2O7 催化剂的制备及其催化丙烷选择氧化脱氢的性能

 以 MgO 修饰的 SBA-15 为载体, 采用浸渍法制备了负载 β-Mg2V2O7 催化剂, 并运用 X 射线衍射、拉曼光谱、紫外-可见漫反射光谱和 H2 程序升温还原等技术对催化剂 V 中心的结构和还原性能进行了表征. 结果表明, β-Mg2V2O7 具有与 α-Mg2V2O7 相同的结构单元, 但其催化丙烷氧化脱氢 (ODH) 反应的初始活性和初始选择性均低于后者. 与体相 β-Mg2V2O7 相比, 负载的 β-Mg2V2O7 上 V 中心分散度以及丙烷 ODH 反应活性和选择性更高, 520 oC 时丙烷 ODH 反应的初始活性提高了约 20 倍, 丙烯初始选择性也从体相的 88.3% 提高到 94.1%, 接近于 α-Mg2V2O7 (94.6%), 并且在 20% 的丙烷转化率时也表现出相似的规律. 这与表征催化剂选择性的两个本征动力学参数 k1/k2 (丙烷初级 ODH 和燃烧反应速率常数之比) 和 k3/k1 (次级丙烯燃烧和初级丙烷 ODH 反应速率常数之比) 反映出的规律一致. 这些对体相和负载的 Mg2V2O7 催化剂催化丙烷 ODH 反应本征特性的认识将有助于设计合成更高效的 Mg-V-O 催化剂, 如基于 α-Mg2V2O7 结构的高分散催化剂, 以获得更高的丙烷 ODH 反应活性和选择性.     

Oxonium Ions Substituting Cesium Ions in the Structure of the New High‐Pressure Borate HP‐Cs1−x(H3O)xB3O5 (x=0.5–0.7)

The new high‐pressure borate HP‐Cs_1?x(H₃O)_xB₃O₅ (x=0.5–0.7) was synthesized under high‐pressure/high‐temperature conditions of 6 GPa/900 °C in a Walker‐type multianvil apparatus. The compound crystallizes in the monoclinic space group C2/c (Z=8) with the parameters a=1000.6(2), b=887.8(2), c=926.3(2) pm, β=103.1(1)°, V=0.8016(3) nm³, R1=0.0452, and wR2=0.0721 (all data). The boron–oxygen network is analogous to those of the compounds HP‐MB₃O₅, (M=K, Rb) and exhibits all three structural motifs of borates—BO₃ groups, corner‐sharing BO₄ tetrahedra, and edge‐sharing BO₄ tetrahedra—at the same time. Channels inside the boron–oxygen framework contain the cesium and oxonium ions, which are disordered on a specific site. Estimating the amount of hydrogen by solid‐state NMR spectroscopy and X‐ray diffraction led to the composition HP‐Cs_1?x(H₃O)_xB₃O₅ (x=0.5–0.7), which implies a nonzero phase width.     

Structural correlations in BaO–PbO–B2O3 glasses as inferred from FTIR spectra

Infrared spectra of xBaO·(30-x)PbO·70B₂O₃, xBaO·(40-x)PbO·60B₂O₃ and xBaO·(50-x)PbO·50B₂O₃ glasses have been quantitatively analyzed. The fraction of four coordinated boron atoms varies linearly, for each group, between the values of the corresponding binary borate glasses. The data could be used to calculate and follow the composition dependence of the concentration of structural units in all glasses. The results show a linear increase in the ratio of PbO forming BO₄ units to the total content of PbO, with increasing B₂O₃ in binary PbO–B₂O₃ glasses. Similar behavior has been observed for the ratio of BaO forming BO₄ units to the total content of BaO in binary BaO–B₂O₃ glasses. The ratio of PbO forming PbO₄ units to the total PbO content, and that of BaO forming asymmetric BO₃ units to the total BaO content, shows a reversed dependence. The linear change in fraction of four coordinated boron atoms and in density and molar volume suggests that the studied glasses can be treated as mixtures of binary PbO–B₂O₃ and BaO–B₂O₃ matrices.     

Synergetic effect between NiO and Ni3V2O8 in propane oxidative dehydrogenation

The oxidative dehydrogenation (ODH) of propane was investigated on Ni-V-O catalysts in a wide range of vanadium contents (5-40%). The addition of a small amount of vanadium significantly increased the catalytic activity of NiO for oxidative dehydrogenation of propane to propene. The formation of propene has a good correlation with the coexistence of NiO and Ni₃V₂O₈. This result strongly suggests that a synergetic effect exists between them in Ni_XV_1-XO_Y (X = 0.95 to 0.6). The best results were obtained with a high Ni/V ratio (e.g. X = 0.95 to 0.85). The active sites and selective oxygen species are discussed. The influence of the catalyst preparation technique and the redox properties of the catalyst were also examined.     

静电纺丝法制备硼掺杂氧化硅纳米纤维用于低碳烷烃氧化脱氢制烯烃

乙烯和丙烯等低碳烯烃是重要的基础有机化工产品,广泛应用于化工生产的各个领域.相比于其他工艺,低碳烷烃氧化脱氢制烯烃工艺具有不受热力学平衡限制、无积炭等特点而被广泛研究.近年发现六方氮化硼(h-BN)、硼化硅(SiB6)和磷酸硼(BPO4)等非金属硼基催化剂能够高效催化烷烃氧化脱氢反应,并抑制产物烯烃的过度氧化,表现出高的催化活性和烯烃选择性.大量的研究表明,硼基催化剂活性起源于催化剂表面的"BO"物种(如B-O和B-OH等基团).氧化硼(B2O3)作为一种氧化气氛中化学性质稳定的含硼化合物,兼具丰富的"BO"位点,在反应条件下可形成多种结构以适用不同的化学环境,为制备高效的烷烃氧化脱氢催化剂提供了可能.在之前的研究中,多将B2O3浸渍在常规的TiO2,SiO2,A12O3等三维多孔载体上用于氧化脱氢反应.考虑到B2O3结构的灵活性和易于成键特性,需开发更为有效的合成策略,以提升B2O3催化剂在氧化脱氢反应中的活性和稳定性.本文采用静电纺丝技术合成了直径为100～150 nm的多孔掺硼二氧化硅纳米纤维(PBSN)用于低碳烷烃氧化脱氢反应.静电纺丝法合成的催化剂中硼物种在开放的氧化硅纤维骨架上均匀分散且稳定固载.一维纳米纤维结构不仅有利于扩散,且赋予催化剂在高重时空速(WHSV)条件下优异的烷烃氧化脱氢反应活性.在乙烷氧化脱氢反应中,当乙烷的转化率达到44.3％时,乙烯的选择性和产率分别为84％和44.2 μmol gcat-1 s-1.而在丙烷脱氢反应中,当丙烷转化率为19.2％时,总烯烃选择性及丙烯产率分别为90％和76.6 μmol gcat-1 s-1.在温度为545 ℃,丙烷WHSV高达84.6 h-1的条件下,催化剂保持长时间稳定.与其他负载型氧化硼催化剂相比,PBSN催化剂具有更高的烯烃选择性和稳定性.研究表明,在氧化硅负载B2O3催化剂催化丙烷氧化脱氢反应中,载体中Si-OH基团的存在可能会降低丙烯的选择性.瞬态分析和动力学实验表明,硼基催化剂催化烷烃氧化脱氢反应过程中O2的活化受到烷烃的影响.本文不仅为高效硼基催化剂的合成提供了新思路,也为深入理解该类催化剂上烷烃氧化脱氢反应过程提供了实验支撑.     

A High-Pressure Praseodymium Fluoride Borate Linking Multiple Structural Features of Apatite-Type Compounds

Pr₅(BO₄)_3−x(BO₃)_x(F,OH)_2.67O_0.28 (x≈1.6), a boron-containing fluoride-oxoapatite-like compound, was obtained by the application of high-pressure/high-temperature synthesis. It exhibits a superstructure of the apatite type with a tripled c lattice parameter (space group P6₃/m) and shows complex anion disorder along the 6₃ screw axis and occupation of distorted octahedra, as well as almost trigonal planar sites, by oxygen and fluorine atoms. Furthermore, a distinct BO₄/(BO₃+F) group disorder is found; 46 % of the sites being occupied by BO₄ groups and 54 % by BO₃ groups, with a fluoride ion located near the missing oxygen atom. The rare earth cations in the 4f sites exhibit a specific distorted tricapped trigonal prismatic coordination with a mean metaprism twist angle of 21.3°. The crystal structure of Pr₅(BO₄)_3−x(BO₃)_x(F,OH)_2.67O_0.28 (x≈1.6) shows much “flexibility” resulting in split and off-site positions of all other rare earth cations. The title compound therefore combines many structural features of apatite-like compounds, for example biologically highly-important carbonated apatites, shedding more light onto the complex structural chemistry of apatites.     

VO3/CeO2(111)催化剂上丙烷氧化脱氢反应活性和选择性的密度泛函理论研究

低碳烯烃一直以来都是化工行业非常重要的基础原料,一般采用烷烃直接热裂解制得,但该方法耗能很大,经济价值有限.近年来,人们开始尝试利用氧化脱氢反应(ODH)方法制备低碳烯烃,并取得了巨大的研究进展,其中稀土氧化物负载钒氧化物催化剂具有良好的低碳烷烃氧化脱氢性能.本文分析了前人对于钒氧化物负载在CeO2表面的计算研究结果,并选取了最具代表性的VO3/CeO2(111)作为烷烃ODH制烯烃的模型催化剂,详细研究了丙烷在该催化剂体系中发生ODH反应机理.通过使用密度泛函理论,对丙烷在VO3/CeO2(111)催化剂上断裂第一根和第二根碳氢键的反应过程进行了理论模拟,并对比了丙烷制丙烯中碳氢键断裂先后的活化能及VO3/CeO2(111)催化剂材料自身的电子性质.结果表明,该催化剂的电子结构在丙烷氧化脱氢反应中扮演关键角色.在丙烷分子断裂第一根碳氢键的反应过程中,会产生两个自由电子,对其电子结构分析发现,其中的一个自由电子会局域在由VO3/CeO2(111)催化剂中五个相关氧原子的2p轨道所形成的新发生局域空轨道(NELS)上,这个独特的新发生局域空轨道只能接受一个电子,另一个电子则会通过丙基在CeO2表面发生吸附将电子传递到CeO2表面的Ce原子上;当丙烷分子进一步发生第二根碳氢键断裂反应时,同样会产生两个新的局域电子,其中一个电子局域在Ce的4f轨道上,此时CeO2表面存在两个局域电子,相互排斥,导致该催化剂上丙烷断裂第二根碳氢键所需的活化能远高于第一根碳氢键.综上,本文对VO3/CeO2(111)催化剂上低碳烷烃ODH反应独特的催化活性和选择性给出了较为细致的分析和解释.     

Controllable construction of Ce-Mn-Ox with tunable oxygen vacancies and active species for toluene catalytic combustion

A series of Ce-Mn-O_x catalysts synthesized under different hydrothermal conditions were evaluated by catalytic removal of toluene. The results of characterization showed that the contents of oxygen vacancies and active species in catalysts were crucial for the catalytic oxidation process. The concentration of Ce³⁺, Mn³⁺, and adsorbed oxygen associated with structural defects in Ce-Mn-O_x catalysts could be controlled by hydrothermal conditions, which were considered to promote redox capacity and improve catalytic oxidation performance. In addition, suitable synthetic conditions could increase the S_BET and V_p of catalysts. Among the prepared catalysts, CM-100 showed the best catalytic performance due to the generation of more defective oxygen and active species (Ce³⁺, Mn³⁺, and surface-adsorbed oxygen). In addition, the CM-100 catalyst showed satisfactory water resistance and stability.     

Hydroxyl‐Mediated Non‐oxidative Propane Dehydrogenation over VOx/γ‐Al2O3 Catalysts with Improved Stability

Supported vanadium oxides are one of the most promising alternative catalysts for propane dehydrogenation (PDH) and efforts have been made to improve its catalytic performance. However, unlike Pt‐based catalysts, the nature of the active site and surface structure of the supported vanadium catalysts under reductive reaction conditions still remain elusive. This paper describes the surface structure and the important role of surface‐bound hydroxyl groups on VO_x / γ‐Al₂O₃ catalysts under reaction conditions employing in situ DRIFTS experiments and DFT calculations. It is shown that hydroxyl groups on the VO_x /Al₂O₃ catalyst (V?OH) are produced under H₂ pre‐reduction, and the catalytic performance for PDH is closely connected to the concentration of V?OH species on the catalyst. The hydroxyl groups are found to improve the catalyst that leads to better stability by suppressing the coke deposition.     

Oxidative dehydrogenation of <Emphasis Type="Italic">n</Emphasis>-butenes to 1,3-butadiene over BiMoFe<Subscript>0.65</Subscript>P<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> catalysts: effect of phosphorous contents

A series of BiMoFe_0.65P _x oxide catalysts with varying phosphorous contents from 0.0 to 0.6 mol ratio were prepared by a co-precipitation method, and oxidative dehydrogenation (ODH) was carried out to produce 1,3-butadiene (BD) from n-butenes. The physico-chemical properties of the oxide catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, N₂ sorption, and NH₃ and 1-butene temperature-programmed desorption (TPD). Among the catalysts studied here, BiMoFe_0.65P_0.1 oxide catalyst showed the highest conversion and selectivity to BD. From the result of 1-butene TPD, the higher catalytic activity is related to the amount of weakly bounded intermediate and the desorbing temperature of strongly bounded intermediates. Also, the higher catalytic activity likely originates from the acidity of the BiMoFe_0.65P_0.1 oxide catalyst; its acidity was higher than that of phosphorous-free oxide catalyst and further contained other oxide catalysts. BiMoFe_0.65P_0.1 oxide catalyst is stable and no significant deactivation for 100 h ODH reaction was shown.     

Molecular mechanism of propane oxidative dehydrogenation on surface oxygen radical sites of VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/TiO<Subscript>2</Subscript> catalysts

Minimum energy pathways of propane oxidative dehydrogenation to propene and propanol on supported vanadium oxide catalyst VO _x /TiO₂ were studied by periodic discrete Fourier transform (DFT) using a surface oxygen radical as the active site. The propene formation pathway was shown to consist of two consecutive hydrogen abstraction steps. The first step includes C_β–H bond activation of propane followed by the formation of a surface hydroxyl group V–O _t H and a propyl radical n-C₃H₇. This step with the activation energy E* = 0.56 eV (54.1 kJ/mol) appears to be rate-determining. The second step involves the reaction of the bridging O _b oxygen atom with the methylene C–H bond of propyl radical n-C₃H₇ followed by the formation of a hydroxylated surface site HO _t –V⁴⁺–O _b H and propene. The initial steps of the C–H bond activation during propane conversion to propanol and propene by ODH on V⁵⁺–(O _t O _b )^? active sites are identical. The obtained results demonstrate that participation of surface oxygen radicals as the active sites of propane ODH makes it possible to explain relatively low activation energies observed for this reaction on the most active catalysts. The presence of very active radical species in low concentration seems to be the key factor for obtaining high selectivity.     

Bulk and surface structures of V2O5/ZrO2 catalysts for n-butane oxidative dehydrogenation

The present investigation focuses on the structural properties and reactivity of zirconia-supported vanadium oxide catalysts, prepared by equilibrium adsorption in basic (pH 10) or in acid (pH 2.7) conditions with vanadium content up to 6 wt.% (pH 10) and up to 11.6 wt.% (pH 2.7). The samples, heated at 823 K for 5 h in air, were characterized by X-ray diffraction, Raman spectroscopy and TPR, both as prepared and after leaching with an ammonia solution to remove species not anchored to the zirconia surface. Some representative samples were also tested for the n-butane oxidative dehydrogenation (ODH) reaction. Depending on vanadium content, various vanadium species were identified by Raman spectroscopy that reacted differently on exposure to H₂. At similar loading, the fraction of vanadium in a dispersed state and thus interacting with the support was higher in samples prepared at pH 10 than in those at pH 2.7. Samples prepared at pH 2.7 contained a higher fraction of large polymeric structures in addition to ZrV₂O₇ and V₂O₅.In line with literature data for propane ODH on similar catalysts, our catalytic results suggested that the active sites for the ODH reaction are associated with the V–O–V bonds of the polymeric exposed structures, whereas the Zr–O–V sites favour alkane combustion.     

Water gas shift reaction catalyzed by osmium carbonyls supported on acid zeolite

Os₃(CO)₁₂ supported on acid zeolite (HX) reacts at high temperature with hydroxyl groups of the support to give a variety of compounds which are active catalysts for the water gas shift reaction. The catalytic activity depends on the thermal treatment.     

Selective Alkane Oxidation by Manganese Oxide: Site Isolation of MnOx Chains at the Surface of MnWO4 Nanorods

The electronic and structural properties of vanadium‐containing phases govern the formation of isolated active sites at the surface of these catalysts for selective alkane oxidation. This concept is not restricted to vanadium oxide. The deliberate use of hydrothermal techniques can turn the typical combustion catalyst manganese oxide into a selective catalyst for oxidative propane dehydrogenation. Nanostructured, crystalline MnWO₄ serves as the support that stabilizes a defect‐rich MnO_x surface phase. Oxygen defects can be reversibly replenished and depleted at the reaction temperature. Terminating MnO_x zigzag chains on the (010) crystal planes are suspected to bear structurally site‐isolated oxygen defects that account for the unexpectedly good performance of the catalyst in propane activation.     

One-pot synthesis of VO x /Al 2 O 3 as efficient catalysts for propane dehydrogenation

Vanadium oxides, as highly efficiently catalysts, are widely applied in various catalytic reactions, such as the dehydrogenation of light alkanes and epoxidation of alkenes. In this paper, a series of VO _x /Al ₂ O ₃ catalysts were fabricated by the 1-pot method for catalytic propane dehydrogenation. The results indicated that the VO _x /Al ₂ O ₃ catalysts with loading of 10 wt.% vanadium exhibited optimized catalytic performance. The as-prepared catalysts were characterized by N ₂ adsorption-desorption, XRD, TEM, H ₂ -TPR, and XPS to explore the texture properties, morphology, and electronic environment of vanadium. In addition, several vanadium catalysts were also prepared by the incipient wetness impregnation (IWI) method to compare their catalytic performance with the 1-pot synthesized catalysts. The catalysts synthesized by the 1-pot method exhibited higher selectivity of propylene and longer catalyst lifetime at high propane conversion when compared to the counterpart synthesized by the IWI method.     

IDM-1: A Zeolite with Intersecting Medium and Extra-Large Pores Built as an Expansion of Zeolite MFI

IDM-1 is a new silica zeolite with an ordered and well-defined framework constructed by alternating pentasil layers and interrupted layers, giving rise to an intersecting system of straight medium pores and undulating extra-large lobed pores. This unique structure was solved by rotation electron diffraction and refined against synchrotron powder X-ray diffraction data. Despite the presence of both Si(OSi)₃(OH) and Si(OSi)₂(OH)₂ sites, this new zeolite presents high thermal stability, withstanding calcination even to 1000 °C. The location of defects at specific sites of the structure results in alternating hydrophobic SiO₂ and hydrophilic SiO_(2−x)(OH)_2x intracrystalline regions. This peculiar combination of intersecting medium and extra-large pores and alternating regions of different chemical character may provide this zeolite with unique catalytic properties.