Topochemical Synthesis of Two‐Dimensional Transition‐Metal Phosphides Using Phosphorene Templates

Transition‐metal phosphides (TMPs) have emerged as a fascinating class of narrow‐gap semiconductors and electrocatalysts. However, they are intrinsic nonlayered materials that cannot be delaminated into two‐dimensional (2D) sheets. Here, we demonstrate a general bottom‐up topochemical strategy to synthesize a series of 2D TMPs (e.g. Co₂P, Ni₁₂P₅, and Co_xFe_2?xP) by using phosphorene sheets as the phosphorus precursors and 2D templates. Notably, 2D Co₂P is a p‐type semiconductor, with a hole mobility of 20.8 cm² V^?1 s^?1 at 300 K in field‐effect transistors. It also behaves as a promising electrocatalyst for the oxygen evolution reaction (OER), thanks to the charge‐transport modulation and improved surface exposure. In particular, iron‐doped Co₂P (i.e. Co_1.5Fe_0.5P) delivers a low overpotential of only 278 mV at a current density of 10 mA cm^?2 that outperforms the commercial Ir/C benchmark (304 mV).     

Electrodeposition of Defect-Rich Ternary NiCoFe Layered Double Hydroxides: Fine Modulation of Co3+ for Highly Efficient Oxygen Evolution Reaction

The low-cost, high-abundance and durable layered double hydroxides (LDHs) have been considered as promising electrocatalysts for oxygen evolution reaction (OER). However, the easy agglomeration of lamellar LDHs in the aqueous phase limits their practical applications. Herein, a series of ternary NiCoFe LDHs were successfully fabricated on nickel foam (NF) via a simple electrodeposition method. The as-prepared Ni(Co_0.5Fe_0.5)/NF displayed an unique nanoarray structural feature. It showed an OER overpotential of 209 mV at a current density of 10 mA cm⁻² in alkaline solution, which was superior to most systems reported so far. As evidenced by the XPS and XAFS results, such excellent performance of Ni(Co_0.5Fe_0.5)/NF was attributed to the higher Co³⁺/Co²⁺ ratio and more defects exposed, comparing with Ni(Co_0.5Fe_0.5)-bulk and Ni(Co_0.5Fe_0.5)-mono LDHs prepared by conventional coprecipitation method. Furthermore, the ratio of Co to Fe could significantly tune the Co electronic structure of Ni(Co_xFe_1-x)/NF composites (x=0.25, 0.50 and 0.75) and affect the electrocatalytic activity for OER, in which Ni(Co_0.5Fe_0.5)/NF showed the lowest energy barrier for OER rate-determining step (from O* to OOH*). This work proposes a facile method to develop high-efficiency OER electrocatalysts.     

Activating CoOOH Porous Nanosheet Arrays by Partial Iron Substitution for Efficient Oxygen Evolution Reaction

Iron‐substituted CoOOH porous nanosheet arrays grown on carbon fiber cloth (denoted as Fe_xCo_1?xOOH PNSAs/CFC, 0≤x≤0.33) with 3D hierarchical structures are synthesized by in situ anodic oxidation of α‐Co(OH)₂ NSAs/CFC in solution of 0.01 m (NH₄)₂Fe(SO₄)₂. X‐ray absorption fine spectra (XAFS) demonstrate that CoO₆ octahedral structure in CoOOH can be partially substituted by FeO₆ octahedrons during the transformation from α‐Co(OH)₂ to Fe_xCo_1?xOOH, and this is confirmed for the first time in this study. The content of Fe in Fe_xCo_1?xOOH, no more than 1/3 of Co, can be controlled by adjusting the in situ anodic oxidation time. Fe_0.33Co_0.67OOH PNSAs/CFC shows superior OER electrocatalytic performance, with a low overpotential of 266 mV at 10 mA cm^?2, small Tafel slope of 30 mV dec^?1, and high durability.     

High Valence State Sites as Favorable Reductive Centers for High-Current-Density Water Splitting

Electrochemical water splitting is a promising approach for producing sustainable and clean hydrogen. Typically, high valence state sites are favorable for oxidation evolution reaction (OER), while low valence states can facilitate hydrogen evolution reaction (HER). However, here we proposed a high valence state of Co³⁺ in Ni_9.5Co_0.5−S−FeO_x hybrid as the favorable center for efficient and stable HER, while structural analogues with low chemical states showed much worse performance. As a result, the Ni_9.5Co_0.5−S−FeO_x catalyst could drive alkaline HER with an ultra-low overpotential of 22 mV for 10 mA cm⁻², and 175 mV for 1000 mA cm⁻² at the industrial temperature of 60 °C, with an excellent stability over 300 h. Moreover, this material could work for both OER and HER, with a low cell voltage being 1.730 V to achieve 1000 mA cm⁻² for overall water splitting at 60 °C. X-ray absorption spectroscopy (XAS) clearly identified the high valence Co³⁺ sites, while in situ XAS during HER and theoretical calculations revealed the favorable electron capture at Co³⁺ and suitable H adsorption/desorption energy around Co³⁺, which could accelerate the HER. The understanding of high valence states to drive reductive reactions may pave the way for the rational design of energy-related catalysts.     

NixCo3‐xO4 Nanoneedle Arrays Grown on Ni Foam as an Efficient Bifunctional Electrocatalyst for Full Water Splitting

Developing highly active, stable and robust electrocatalysts based on earth‐abundant elements for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is important for many renewable energy conversion processes. Herein, Ni_xCo_3‐xO₄ nanoneedle arrays grown on 3D porous nickel foam (NF) was synthesized as a bifunctional electrocatalyst with OER and HER activity for full water splitting. Benefiting from the advantageous structure, the composite exhibits superior OER activity with an overpotential of 320 mV achieving the current density of 10 mA cm^?2. An exceptional HER activity is also acquired with an overpotential of 170 mV at the current density of 10 mA cm^?2. Furthermore, the catalyst also shows the superior activity and stability for 20 h when used in the overall water splitting cell. Thus, the hierarchical 3D structure composed of the 1D nanoneedle structure in Ni_xCo_3‐xO₄/NF represents an avenue to design and develop highly active and bifunctional electrocatalysts for promising energy conversion.     

Controlled Synthesis of 3D Flower‐like Ni2P Composed of Mesoporous Nanoplates for Overall Water Splitting

Developing efficient non‐noble metal and earth‐abundant electrocatalysts with tunable microstructures for overall water splitting is critical to promote clean energy technologies for a hydrogen economy. Herein, novel three‐dimensional (3D) flower‐like Ni₂P composed of mesoporous nanoplates with controllable morphology and high surface area was prepared by a hydrothermal method and low‐temperature phosphidation as efficient electrocatalysts for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Compared with the urchin‐like Ni_x P_y , the 3D flower‐like Ni₂P with a diameter of 5 μm presented an efficient and stable catalytic performance in 0.5 m H₂SO₄, with a small Tafel slope of 79 mV dec⁻¹ and an overpotential of about 240 mV at a current density of 10 mA cm⁻² with a mass loading density of 0.283 mg cm⁻². In addition, the catalyst also exhibited a remarkable performance for the OER in 1.0 m KOH electrolyte, with an overpotential of 320 mV to reach a current density of 10 mA cm⁻² and a small Tafel slope of 72 mV dec⁻¹. The excellent catalytic performance of the as‐prepared Ni₂P may be ascribed to its novel 3D morphology with unique mesoporous structure.     

Tunable and Specific Formation of C@NiCoP Peapods with Enhanced HER Activity and Lithium Storage Performance

The superior properties of nanomaterials with a special structure can provide prospects for highly efficient water splitting and lithium storage. Herein, we fabricated a series of peapodlike C@Ni_2?xCo_xP (x≤1) nanocomposites by an anion‐exchange pathway. The experimental results indicated that the HER activity of C@Ni_2?xCo_xP catalyst is strongly related to the Co/Ni ratio, and the C@NiCoP got the highest HER activity with low onset potential of ～45 mV, small Tafel slope of ～43 mV dec^?1, large exchange current density of 0.21 mA cm^?2, and high long‐term durability (60 h) in 0.5 m H₂SO₄ solutions. Equally importantly, as an anode electrode for lithium batteries, this peapodlike C@NiCoP nanocomposite gives excellent charge–discharge properties (e.g., specific capacity of 670 mAh g^?1 at 0.2 A g^?1 after 350 cycles, and a reversible capacity of 405 mAh g^?1 at a high current rate of 10 A g^?1). The outstanding performance of C@NiCoP in HER and LIBs could be attributed to the synergistic effect of the rational design of peapodlike nanostructures and the introduction of Co element.     

Improving the Electrocatalytic Activity of a Nickel-Organic Framework toward the Oxygen Evolution Reaction through Vanadium Doping

Metal-organic frameworks (MOFs) have been considered as potential oxygen evolution reaction (OER) electrocatalysts owning to their ultra-thin structure, adjustable composition, high surface area, and high porosity. Here, we designed and fabricated a vanadium-doped nickel organic framework (V_1−x−Ni_xMOF) system by using a facile two-step solvothermal method on nickel foam (NF). The doping of vanadium remarkably elevates the OER activity of V_1−x−Ni_xMOF, thus demonstrating better performance than the corresponding single metallic Ni-MOF, NiV-MOF and RuO₂ catalysts at high current density (>400 mA cm⁻²). V_0.09−Ni_0.91MOF/NF provides a low overpotential of 235 mV and a small Tafel slope of 30.3 mV dec⁻¹ at a current density of 10 mA cm⁻². More importantly, a water-splitting device assembled with Pt/C/NF and V_0.09−Ni_0.91MOF/NF as cathode and anode yielded a cell voltage of 1.96 V@1000 mA cm⁻², thereby outperforming the-state-of-the-art RuO₂⁽⁺⁾||Pt/C⁽⁻⁾. Our work sheds new insight on preparing stable, efficient OER electrocatalysts and a promising method for designing various MOF-based materials.     

Heterostructured Inter-Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition-metal-oxides (TMOs)-based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter-doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm⁻² and a small Tafel slope of 23.5 mV dec⁻¹, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm⁻². As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm⁻² for alkaline overall water splitting.     

Sulfur-Modified Oxygen Vacancies in Iron–Cobalt Oxide Nanosheets: Enabling Extremely High Activity of the Oxygen Evolution Reaction to Achieve the Industrial Water Splitting Benchmark

The oxygen vacancies of defective iron–cobalt oxide (FeCoO_x-Vo) nanosheets are modified by the homogeneously distributed sulfur (S) atoms. S atoms can not only effectively stabilize oxygen vacancies (Vo), but also form the Co−S coordination with Co active site in the Vo, which can modulate the electronic structure of the active site, enabling FeCoO_x-Vo-S to exhibit much superior OER activity. FeCoO_x-Vo-S exhibits a mass activity of 2440.0 A g⁻¹ at 1.5 V vs. RHE in 1.0 m KOH, 25.4 times higher than that of RuO₂. The Tafel slope is as low as 21.0 mV dec⁻¹, indicative of its excellent charge transfer rate. When FeCoO_x-Vo-S (anode catalyst) is paired with the defective CoP₃/Ni₂P (cathode catalyst) for overall water splitting, current densities of as high as 249.0 mA cm⁻² and 406.0 mA cm⁻² at a cell voltage of 2.0 V and 2.3 V, respectively, can be achieved.     

Tweaking Nickel with Minimal Silver in a Heterogeneous Alloy of Decahedral Geometry to Deliver Platinum-like Hydrogen Evolution Activity

Five-fold intertwined Ag_xNi_1−x (x=0.01–0.25) heterogeneous alloy nanocrystal (NC) catalysts, prepared through unique reagent combinations, are presented. With only ca. 5 at % Ag (AgNi-5), Pt-like activity has been achieved at pH 14. To reach a current density of 10 mA cm⁻² the extremely stable AgNi-5 requires an overpotential of 24.0±1.2 mV as compared to 20.1±0.8 mV for 20 % Pt/C, both with equal catalyst loading of 1.32 mg cm⁻². The turnover frequency (TOF) is as high as 2.1 H₂ s⁻¹ at 50 mV (vs. RHE). Site-specific elemental analyses show the Ag:Ni compositional variation, where the apex and edges of the decahedra are Ag-rich, thereby exposing Ni onto the faces to achieve maximum charge transport for an exceptional pH universal HER activity. DFT calculations elucidate the relative H-atom adsorption capability of the Ni centers as a function of their proximity to Ag atom.     

Crystal structure and Raman scattering characterization of Cu2Fe1-xCoxSnS4 chalcogenide compounds

This work reports the synthesis by solid–state reaction of Cu₂Fe_1-xCo_xSnS₄ solid solutions. Crystal structures of Cu₂Fe_0.8Co_0.2SnS₄ and Cu₂Fe_0.6Co_0.4SnS₄ were investigated by single crystal X-ray diffraction. Both phases crystallize in the tetragonal stannite-type structure. The volume of the tetrahedral [MS₄] (M = Fe, Co) presented the highest distortion, with Edge-Length Distortion (ELD) indices ∼2% from the ideal tetrahedron. The powder X-ray diffraction (XRD) patterns of Cu₂Fe_1-xCo_xSnS₄ (x = 0.2, 0.4, 0.6 and 0.8) has been refined by Rietveld method. No secondary phases were detected in XRD patterns. An analysis of the vibrational properties of Cu₂Fe_1-xCo_xSnS₄ was performed using Raman scattering measurements. The Raman peaks were analyzed by fitting of the spectra and subsequently identifying the vibrational modes by comparison with experimental and theoretical data from Cu₂FeSnS₄ (CFTS) and Cu₂CoSnS₄ (CCTS) end-members. The spectra from Cu₂Fe_1-xCo_xSnS₄ show that there is a variation in the frequency of the main A₁ peak at ∼320 cm⁻¹ together with a decrease in the secondary mode intensity at ∼285 cm⁻¹. Full Width at Half Maximum (FWHM) and the intensity of the Raman peaks reflect the high crystallinity of Cu₂Fe_1-xCo_xSnS₄ solid solutions. The oxidation states of the metals were confirmed by temperature-dependent magnetization measurements performed in the antiferromagnetic Cu₂Fe_1-xCo_xSnS₄ solid solutions.     

Enhanced Supercapacitor Performance Using a Co3O4@Co3S4 Nanocomposite on Reduced Graphene Oxide/Ni Foam Electrodes

To avoid an enormous energy crisis in the not-too-distant future, it be emergent to establish high-performance energy storage devices such as supercapacitors. For this purpose, a three-dimensional (3D) heterostructure of Co₃O₄ and Co₃S₄ on nickel foam (NF) that is covered by reduced graphene oxide (rGO) has been prepared by following a facile multistep method. At first, rGO nanosheets are deposited on NF under mild hydrothermal conditions to increase the surface area. Subsequently, nanowalls of cobalt oxide are electro-deposited on rGO/Ni foam by applying cyclic-voltammetry (CV) under optimized conditions. Finally, for the synthesis of Co₃O₄@Co₃S₄ nanocomposite, the nanostructure of Co₃S₄ was fabricated from Co₃O₄ nanowalls on rGO/NF by following an ordinary hydrothermal process through the sulfurization for the electrochemical application. The samples are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The obtained sample delivers a high capacitance of 13.34 F cm⁻² (5651.24 F g⁻¹) at a current density of 6 mA cm⁻² compared to the Co₃O₄/rGO/NF electrode with a capacitance of 3.06 F cm⁻² (1230.77 F g⁻¹) at the same current density. The proposed electrode illustrates the superior electrochemical performance such as excellent specific energy density of 85.68 W h Kg⁻¹, specific power density of 6048.03 W kg⁻¹ and a superior cycling performance (86% after 1000 charge/discharge cycles at a scan rate of 5 mV s⁻¹). Finally, by using Co₃O₄ @Co₃S₄/rGO/NF and the activated carbon-based electrode as positive and negative electrodes, respectively, an asymmetric supercapacitor (ASC) device was assembled. The fabricated ASC provides an appropriate specific capacitance of 79.15 mF cm⁻² at the applied current density of 1 mA cm⁻², and delivered an energy density of 0.143 Wh kg⁻¹ at the power density of 5.42 W kg⁻¹.     

In Situ Synthesis of CoCeSx Bimetallic Sulfide Nanoparticles on a Bi-Pyrene Terminated Molecular Wire Modified Graphene Surface for Supercapacitors

The excellent electrical conductivity of graphene is due to its highly-conjugated structures. Manipulation of the electronic and mechanical properties of graphene can be achieved by controlling the destruction of its in-sheet conjugation system. Herein, we report the preparation of CoCeS_x−SA@BPMW@RGO through π-π stacking interactions at the molecular level. In this study, sodium alginate was reacted with Co²⁺ and Ce³⁺, and the composite was loaded onto a graphene surface. The graphene sheets were prepared using a bi-pyrene terminated molecular wire (BPMW) to avoid re-stacking of the grapheme sheets, thereby forming nanoscale spaces between sheets. The angle between the BPMW coplanar pyrene group and the phenyl group was 33.2°, and the graphene layer is supported in an oblique direction. Finally, a three-dimensional porous composite was obtained after annealing and vulcanization. The obtained CoCeS_x−SA@BPMW@RGO exhibited excellent electrical conductivity and remarkable cycle stability. When the current density was 1 A g⁻¹, its specific capacitance was as high as 1004 F g⁻¹. BPMW modifies graphene through the synergistic effect of π-π stacking interaction and special structure to obtain excellent electrochemical performance. Moreover, a solid-state asymmetric supercapacitor device was fabricated based on the synthesized CoCeS_x−SA@BPMW@RGO hybrid, which exhibited a power density of 979 W kg⁻¹ at an energy density of 23.96 Wh kg⁻¹.     

Composition-Tunable Antiperovskite CuxIn1−xNNi3 as Superior Electrocatalysts for the Hydrogen Evolution Reaction

A group of newly reported antiperovskite nitrides Cu_xIn_1−xNNi₃ (0≤x≤1) with tunable composition are employed as electrocatalysts for the hydrogen evolution reaction (HER). Cu_0.4In_0.6NNi₃ shows the highest intrinsic performance among all developed catalysts with an overpotential of merely 42 mV at 10 mA cm_geo⁻². Stability tests at a high current density of 100 mA cm_geo⁻² show its super-stable performance with only 7 mV increase in overpotential after more than 60 hours of measurement, surpassing commercial Pt/C (increase of 170 mV). By partial substitution, the derived antiperovskite nitride achieves a smaller kinetic barrier of water dissociation compared to the unsubstituted InNNi₃ and CuNNi₃, revealed by first-principle calculations. It is found that the partially substituted Cu_xIn_1−xNNi₃ possesses a thermal neutral and desirable Gibbs free energy of hydrogen for HER, ascribed to the tailoring of the energy of d-band center arose by the A-site (A=Cu or In) substitution and a resulting optimization of adsorbate interactions.     

Gelatin-Derived 1D Carbon Nanofiber Architecture with Simultaneous Decoration of Single Fe−Nx Sites and Fe/Fe3C Nanoparticles for Efficient Oxygen Reduction

Exploring high-performance non-precious-metal electrocatalysts for the oxygen reduction reaction (ORR) is critical. Herein, a scalable and cost-effective strategy is reported for the construction of one-dimensional carbon nanofiber architectures with simultaneous decoration of single Fe−N_x sites and highly dispersed Fe/Fe₃C nanoparticles for efficient ORR, through the Fe^III-complex-assisted electrospinning of gelatin nanofibers with subsequent pre-oxidation and carbonization. Results show that the presence of a Fe^III complex enables the 1D gelatin nanofibers to be well retained during the pre-oxidation process. Owing to the distinct 1D nanofiber structure and the synergistic effect of Fe/Fe₃C and Fe−N_x sites, the resulting electrocatalyst is highly active for ORR with a half-wave potential of 0.885 V (outperforming commercial Pt/C) and a superior electrochemical stability in alkaline electrolytes. Similarly, it also shows a high power density (144.7 mW cm⁻²) and a superior stability in Zn-air batteries. This work opens a path for the design and synthesis of 1D carbon electrocatalyst for efficient ORR catalysis.     

Bimetallic Cage-Based Metal–Organic Frameworks for Electrochemical Hydrogen Evolution Reaction with Enhanced Activity

A cage-based metal–organic framework (Ni-NKU-101) with biphenyl-3,3’,5,5’-tetracarboxylic acid was synthesized via solvothermal method. Ni-NKU-101 contains two types of cages based on trinuclear and octa-nuclear nickel-clusters that are connected with each other by the 4-connected ligands, to form a 3D framework with a new topology. A mixed-metal strategy was used to synthesize isostructural bimetallic MOFs of M_xNi_1-x-NKU-101 (M=Mn, Co, Cu, Zn). The electrocatalytic studies showed that the hydrogen evolution reaction (HER) activity of Cu_xNi_1-x-NKU-101 is much higher than that of other M_xNi_1-x-NKU-101 catalysts in acidic aqueous solution, owing to the synergistic effect of the bimetallic centers. The optimized Cu_0.19Ni_0.81-NKU-101 has an overpotential of 324 mV at 10 mA cm⁻² and a Tafel slope of 131 mV dec⁻¹. The mechanism of HER activity over these bimetallic MOF-based electrocatalysts are discussed in detail.     

Highly Conductive Cobalt Perthiolated Coronene Complex for Efficient Hydrogen Evolution

Metal-bis(dithiolene) is one of the most promising structures showing redox activity, excellent electron transport and magnetic properties as well as catalytic activities. Perthiolated coronene (PTC), an emerging highly symmetric ligand containing the smallest graphene nanoplate was employed to manufacture a hybrid material with fused metal-bis(dithiolene) and graphene nanoplate, and it has been demonstrated as an efficient strategy for the construction of multifunctional materials recently. Herein, Co-PTC, a 2D MOF containing Co-bis(dithiolene) and coronene units is prepared via a homogeneous reaction for the first time as powder samples, which are bar-shaped microparticles composed of nanosheets. A neutral formula of [Co₃(C₂₄S₁₂)]_n is verified for Co-PTC. Co-PTC plays an ultrahigh conductivity of approximately 45 S cm⁻¹ at room temperature as compressed samples, which is among the highest value ever reported for the compressed powder samples of conducting MOFs. Moreover, Co-PTC exhibits good electrocatalytic performance in the hydrogen evolution reaction (HER) with a Tafel slope of 189 mV decade⁻¹ and an operating overpotential of 227 mV at 10 mA cm⁻¹ with pH=0, as well as a remarkable stability in the extremely acidic aqueous solutions, which is the best hydrogen evolution properties among metal–organic compounds.     

Electrochemical Phase Evolution of Metal-Based Pre-Catalysts for High-Rate Polysulfide Conversion

In situ evolution of electrocatalysts is of paramount importance in defining catalytic reactions. Catalysts for aprotic electrochemistry such as lithium–sulfur (Li-S) batteries are the cornerstone to enhance intrinsically sluggish reaction kinetics but the true active phases are often controversial. Herein, we reveal the electrochemical phase evolution of metal-based pre-catalysts (Co₄N) in working Li-S batteries that renders highly active electrocatalysts (CoS_x). Electrochemical cycling induces the transformation from single-crystalline Co₄N to polycrystalline CoS_x that are rich in active sites. This transformation propels all-phase polysulfide-involving reactions. Consequently, Co₄N enables stable operation of high-rate (10 C, 16.7 mA cm⁻²) and electrolyte-starved (4.7 μL mg_S⁻¹) Li-S batteries. The general concept of electrochemically induced sulfurization is verified by thermodynamic energetics for most of low-valence metal compounds.     

Molecular Ligand-Mediated Assembly of Multicomponent Nanosheet Superlattices for Compact Capacitive Energy Storage

Inspired by the self-assembly of nanoparticle superlattices, we report a general method that exploits long-chain molecular ligands to induce ordered assembly of colloidal nanosheets (NSs), resulting in 2D laminate superlattices with high packing density. Co-assembly of two types of NSs further enables 2D/2D heterostructured superlattices. As a proof of concept, co-assembly of Ti₃C₂T_x and graphene oxide (GO) NSs followed by thermal annealing leads to MXene-rGO superlattices with tunable microstructures, which exhibit significantly higher capacitance than their filtrated counterparts, delivering an ultrahigh volumetric capacitance of 1443 F cm⁻³ at 2 mV s⁻¹. Moreover, the as-fabricated binder-free symmetric supercapacitors show a high volumetric energy density of 42.1 Wh L⁻¹, which is among the best reported for MXene-based materials in aqueous electrolytes. This work paves the way toward rational design of 2D material-based superstructures for energy applications.