Coaxial laser cladding on an inclined substrate

This paper describes an experimental and theoretical study of the cladding mode of coaxial laser cladding on an inclined substrate. Based on the image analysis of the powder stream and clad profile measurements in coaxial laser cladding, it was found that irregular clad profiles always formed on an inclined surface and the location of the peak profile shifted away from the clad center. This phenomenon is caused by uneven distributions of powder concentration and laser beam intensity. A modified Gaussian mode for powder stream and laser beam was proposed to estimate the clad profiles on an inclined plane under laser beam irradiation. The effects of the inclined steel substrate on the CO₂ laser beam absorption and stainless-steel powder catchment were examined experimentally. The results show that both the laser absorption and the powder catchment on the mild steel decrease with increasing the cladding angle. From the analysis of laser beam mode, the clad width is equivalent to the beam spot size on the inclined substrate. However, the clad height correlates well with the distribution of the powder concentration. The results show that the Gaussian cladding mode could be adopted in various laser cladding applications such as rapid prototyping and butt welding to predict the clad profiles precisely.     

Prediction of clad angle in laser cladding by powder using response surface methodology and scatter search

Currently, laser cladding is an important process that allows the deposition of thick protective coatings on substrates. The article presents an experimental investigation of the influence of processing parameters on clad angle in laser cladding by powder (LCP). The clad angle is determined from the mathematical expression relating to the clad height and clad width. The cladding angle model was developed in terms of laser power, scanning speed, and powder mass flow rate by means of response surface methodology. A first-order equation covering a narrow range of the variables and a second-order equation covering a wide range of the variables are presented. An optimization technique, Scatter Search, is used to determine optimal processing parameters. The adequacy of the predictive model was tested by analysis of variance and found to be adequate.     

Plunging method for Nd : YAG laser cladding with wire feeding

The effects of wire feeding direction and position, cladding time, and cladding speed on the quality of cladding layer for laser cladding with wire feeding are studied. Experiment results indicate that the wire feeding direction and position are important for wire laser cladding. By adopting the correct wire feeding direction and position, the wire can be plunged into the melt pool and can be melted by the heat of the molten metal. With the increase of cladding speed, the dilution of clad layer can be reduced and the growth of the grain size of heat-affected zone of the base metal can be limited. If proper cladding parameters are used, the clad layers will have a good surface shape, sound metallurgical bonding with base metal, low dilution, and the effect of heating on heat-affected zone metal can be limited. The hardness of the clad layer and heat-affected zone are checked. It indicates that with the increase of cladding speed, the hardness of the clad layer and heat-affected zone increases.     

Estimation of laser solid forming process based on temperature measurement

By using a moving disc heat source model, an analytical model was developed to describe laser solid forming (LSF) process with the feedback of the surface temperature of the molten pool, which can be used to estimate the geometric characterizations (width and height) of the clad layer rapidly. An on-line temperature measurement system was established and some single-pass cladding experiments were conducted while the molten pool temperature was monitored. It was found that the estimated geometric characterizations agreed well with the experimental results. In addition, the power consumed by conduction, convection, radiation, evaporation and absorption during LSF were also estimated by the model. It was shown that the majority of the total absorbed power was conducted to the substrate. The effective model can not only be used to optimize the processing parameters but also potentially applied to the real-time feedback control.     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.     

Study on cross-section clad profile in coaxial single-pass cladding with a low-power laser

In this paper, a model of cross-section clad profile on the substrate in coaxial single-pass cladding with a low-power laser was studied. The static model of powder mass concentration distribution at cold-stream conditions was defined as a Gaussian function. In coaxial single-pass cladding with a low-power laser, since the influence of surface tension, gravity and gas flow on the clad bead could be neglected, the cross-section profile of the clad bead deposited by a low-power laser on the substrate was dominated by the powder concentration at each point on the pool and the time when the material was liquid at this point. The height of each point on the cross-section clad profile was defined as a definite integration of a Gaussian function from the moment at which the melt pool was just arriving at the point to the moment at which the point left the melt pool. In the presented experiment, powder of Steel 63 (at 0.63 wt% C) was deposited on a substrate of Steel 20 (at 0.20 wt% C) at the laser power of 135 W. The experimental results testified the model.     

激光工艺参数对钛合金表面NiCrBSi合金熔覆层组织及硬度的影响

在TC4合金表面进行了激光熔覆NiCrBSi合金涂层的试验 ,利用SEM和XRD等对熔覆层的微观组织进行了分析 ,测试了熔覆层的显微硬度。结果表明 ,激光工艺参数对熔覆层的组织和硬度有极大的影响 ,随稀释率的增加 ,激光熔覆层中形成了TiB2 和TiC等颗粒增强相 ,熔覆层的硬度明显提高。     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

Formation of cross-sectional profile of a clad bead in coaxial laser cladding

In order to determine a cross-sectional profile of a clad bead in coaxial laser cladding, its formation mechanism is investigated theoretically and experimentally. In laser cladding, every point at the back edge of a melt pool is contributed to a cross-sectional profile of the clad bead to be formed, and points at the same pool edge but on different cross sections are located at different cross-sectional profiles of the clad bead. A cross-sectional profile of a clad bead is composed of points of intersection between the cross section and a series of pool edges. Model of the cross-sectional clad profile in single-pass coaxial laser cladding is developed. A 500 W CO₂ laser is used in the experiment. The experimental result agrees well with the calculated cross-sectional clad profile.     

Effects of process variables on laser direct formation of thin wall

In this paper, effects of process variables on wall thickness, powder primary efficiency and speed of forming a thin metallic wall in single-pass coaxial laser cladding are investigated, and some resolution models are established and testified experimentally. With some assumptions, each of wall thickness, powder primary efficiency and formation speed can be defined as a function of the process variables. Wall thickness is equal to width of the molten pool created in single-pass laser cladding and determined by laser absorptivity, laser power, initial temperature, scanning speed and thermo-physical properties of clad material. Powder primary efficiency and formation speed are both dependent on an exponential function involving the ratio of melt pool width, which is decided by the process variables, to powder flow diameter. In addition, formation speed is influenced by powder feed rate. In present experiment, a 500 W continual-wave (CW) CO₂ laser is used to produce thin-wall samples by single-pass coaxial laser cladding. The experimental results agree well with the calculation values despite some errors.     

铁基合金激光熔覆层高温润滑磨损性能

 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。     

3-D finite element modeling of laser cladding by powder injection: effects of laser pulse shaping on the process

This paper introduces a 3-D transient finite element model of laser cladding by powder injection to investigate the effects of laser pulse shaping on the process. The proposed model can predict the clad geometry as a function of time and process parameters including laser pulse shaping, travel velocity, laser pulse energy, powder jet geometry, and material properties. In the proposed strategy, the interaction between powder and melt pool is assumed to be decoupled and as a result, the melt pool boundary is first obtained in the absence of powder spray. Once the melt pool boundary is obtained, it is assumed that a layer of coating material is deposited on the intersection of the melt pool and powder stream in the absence of the laser beam in which its thickness is calculated based on the powder feedrate and elapsed time. The new melt pool boundary is then calculated by thermal analysis of the deposited powder layer, substrate and laser heat flux. The process is simulated for different laser pulse frequencies and energies. The results are presented and compared with experimental data. The quality of clad bead for different parameter sets is experimentally evaluated and shown as a function of effective powder deposition density and effective energy density. The comparisons show excellent agreement between the modeling and experimental results for cases in which a high quality clad bead is expected.     

Thermal performance investigation of DQW GaInNAs laser diodes

In this work, we optimize the thermal performance of a double quantum well GaInNAs ridge waveguide laser using an accurate in-house 2D electro-opto-thermal laser simulator. The simulator has shown good agreement with experiments after a detailed calibration procedure. Using calibrated material parameters, we investigate the influence of the cladding doping level on the heat generation within the laser. It is found that due to the competition between Joule heating and free carrier absorption, an optimum cladding doping level exists.     

40Cr钢表面激光熔覆层的磨损性能

 为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。     

Numerical investigation of the microstructure of a clad layer produced via laser cladding with coaxial metal powder injection

The microstructure of a clad layer produced via selective laser cladding with coaxial metal powder injection is studied numerically. The Johnson–Mehl–Avrami–Kolmogorov equation for condensed systems with inhomogeneous rates of nucleation is used to model the phase change kinetics. The impact of the substrate boundary along with interconnected heat transfer and phase change processes on the final microstructure of a built-up layer is demonstrated. The qualitative difference between the behavior of the temperature on the built-up layer’s surface and at the depth of the substrate is established, revealing the inhomogeneous microstructure of the final layer.     

Numerical simulation of temperature distribution and TiC growth kinetics for high power laser clad TiC/NiCrBSiC composite coatings

A three dimensional model was proposed to simulate high power laser clad TiC/NiCrBSiC composite coatings on Ti6Al4V alloys. The temperature distribution, temperature curves on different nodes, three dimensional shape and size of TiC melting region, molten pool and heat affected zone (HAZ) of the substrate were obtained. To have a clear physical insight into the phase transformation and microstructure evolution in the coatings during laser cladding process, a theoretical kinetic analysis was performed to elucidate the nucleation, growth velocity, and size of TiC particles on the basis of simulated temperature curves of the molten pool. A good quality TiC/NiCrBSiC composite coating with low dilution rate and excellent metallurgical bond was fabricated under optimal processing parameters using powder mixture of TiC and NiCrBSiC as clad material and cuboid of Ti6Al4V alloys as substrate. To validate the reliability of the proposed model, the theoretical results were compared with the microstructure of the coatings. It shows that these theoretical results are in excellent agreement with the experiment cases.     

Analysis and prediction of single laser tracks geometrical characteristics in coaxial laser cladding process

Direct Laser Fabrication is a promising new manufacturing technology coming from laser cladding process. From a coaxial nozzle, powder is fed through a laser beam on a substrate. The powder melting and solidification processes lead to the fabrication of a part layer by layer. In this work 316L stainless steel powder is used to form laser tracks on a low carbon steel substrate. The layer geometry is an important process characteristic to control the final part of fabrication. This paper presents analytical relationships between the laser tracks geometrical characteristics (width, height, area, penetration depth) and the processing parameters (laser power P, scanning speed V and powder mass flow Q_m). Three values of each processing parameters are fixed and so 27 different experiments have been made and analyzed. The validity of these results is discussed studying the correlation coefficient R, the graphical analysis of the residuals and the uncertainty evaluations. Two kinds of models are studied to predict the form and the geometrical characteristics of the single laser tracks cross sections. The first one is an analytical model in which the distribution of the powder in the feed jet is supposed to govern the laser clad geometry. Three distributions are proposed: Gaussian, uniform and polynomial. In the second model the general form of the clad cross section is supposed to be a disk due to the surface tension forces. Analytical relationships are established between the radius and the center of the disk in one hand and the process parameters in the other hand. This way we show that we can reproduce the laser track geometry in all the area experimentally explored.     

Analytical modeling and experimental investigation of laser induction hybrid rapid cladding for Ni-based WC composite coatings

Laser induction hybrid rapid cladding (LIHRC) cannot only increase the cladding efficiency, but can also eliminate porosity and cracking of ceramic–metal composite coatings. In order to obtain a deep understanding of LIHRC with rapid cladding speed and high powder deposition rate, an analytical model of LIHRC for Ni-based WC composite coatings is proposed in the paper. The predictions of cladding height and powder efficiency obtained with this model are in good agreement with experimental results. Injection angles at which the attenuation rate of laser power is relatively low are identified and crack-free composite coatings with smooth surface, good profile and metallurgical bonding to substrate can be obtained. The calculated results for the temperature of the powder particles are compared to experimental data of the microhardness profiles and show a similar trend.     

Numerical simulation of powder transport behavior in laser cladding with coaxial powder feeding

Laser cladding with coaxial powder feeding is one of the new processes applied to produce well bonding coating on the component to improve performance of its surface. In the process, the clad material is transported by the carrying gas through the coaxial nozzle, generating gas-powder flow. The powder feeding process in the coaxial laser cladding has important influence on the clad qualities. A 3D numerical model was developed to study the powder stream structure of a coaxial feeding nozzle. The predicted powder stream structure was well agreed with the experimental one. The validated model was used to explore the collision behavior of particles in the coaxial nozzle, as well as powder concentration distribution. It was found that the particle diameter and restitution coefficient greatly affect the velocity vector at outlet of nozzle due to the collisions, as well as the powder stream convergence characteristics below the nozzle. The results indicated a practical approach to optimize the powder stream for the coaxial laser cladding.     

Effects of processing parameters on structure of Ni-based WC composite coatings during laser induction hybrid rapid cladding

The relationships between the processing parameters (i.e. laser specific energy, powder density, preheated temperature of substrate and types of substrate) and the structure characteristics of Ni-based WC composite coatings during laser induction hybrid rapid cladding (LIHRC) were investigated systematically. The results show that laser specific energy, cladding height and contact angle have a linear relation with powder density, as can provide the predictions of laser processing parameters according to the geometrical characteristics of a single laser track (i.e. cladding height, cladding width). Moreover, dilution of composite coating increases with the increasing of laser specific energy and the preheated temperature of substrate, while reduces with the increasing of powder density. The types of substrate also have an important effect on dilution of composite coating, as has a strong dependence on the thermophysical properties of substrate (i.e. melting point, resistivity and permeability).