煤中痕量元素在循环流化床锅炉中的迁移行为与富集特性

对天津市某电厂循环流化床(CFB)锅炉燃用的原煤及燃烧产物底灰、飞灰、细飞灰(≤50 μm)进行痕量元素含量的测定,分析了Be、Zn、Hg、V、Cr、Mn、Co、Ni、Cu、As、Se、Cd、Pb 13种痕量元素在燃烧过程中的迁移行为,揭示了痕量元素在CFB锅炉中的分配、富集特性。结果表明,CFB锅炉中,较低的炉温对于痕量元素的迁移富集产生了较大的影响。由相对富集系数得知,Be、V、Co、Se在底灰中耗散,在飞灰中富集,Zn、Mn倾向于在底灰中富集,元素Cd、Pb、Ni、Cu挥发性较强,在底灰和飞灰中均是耗散。As受钙氧化物影响,挥发性表现并不明显。Hg在底灰和飞灰中相对富集系数均很低,表明Hg在整个燃烧过程中以气态形式排放;Hg、As、Se、V、Cr、Mn、Co、Ni、Cu、Zn、Pb均有向小颗粒物中富集的趋势。根据相对富集系数以及研究的13种元素在低温CFB锅炉中的迁移行为,将这些元素分为三类:A类(E_R<0.1),主要是以气态形式排放元素Hg;B类(0.1R≤0.85),较易挥发元素As、Be、Ni、Cu、Se、Cd、Pb、Co、V;C类(E_R>0.85),主要残留在固体产物中元素Zn、Mn、Cr。     

Certification of the contents of some heavy metals (Cd, Co, Cu, Mn, Hg, Ni, Pb and Zn) in three types of sewage sludge

Summary The element contents of Cd, Co, Cu, Mn, Hg, Ni, Pb and Zn of three different types of sewage sludge were certified. The preparation, the homogeneity and the stability are reported. The certified contents as well as values for Cr and Se and for the aqua regia soluble contents of Cd, Cr, Co, Cu, Mn, Ni, Pb and Zn are given.

---

Zertifizierung von Schwermetallspuren (Cd, Co, Cu, Mn, Hg, Ni, Pb und Zn) in drei Klärschlammproben

Zusammenfassung In drei verschiedenen Klärschlammproben wurden die Elementgehalte an Cd, Co, Cu, Mn, Hg, Ni, Pb und Zn zertifiziert. Es wird berichtet über die Herstellung, Homogenität und Stabilität. Die zertifizierten Gehalte sowie der Gehalt von Cr, Se und der Gehalt an königswasserlöslichem Cd, Cr, Co, Cu, Mn, Ni, Pb und Zn werden angegeben.

     

酸洗污泥与煤共燃烧过程中重金属的迁移分布研究

采用高温管式炉系统进行酸洗污泥与煤共燃烧实验。对共燃烧后As、Cr、Ni、Cd、Cu、Mn、Pb、Zn、Sb、Se重金属元素在烟气、飞灰及炉渣中的分配率进行分析。结果表明,Cd、Se、Zn是易挥发重金属,主要分布在烟气和飞灰中。Cd在烟气中的最大分配率为61%;Se在烟气中的分配率为38.58%~94.612%;Zn在低、高温段分别主要分布在烟气和飞灰中。As、Cu、Pb、Sb是半挥发重金属,Pb在炉渣中的分配率较稳定,分配率为42.67%~64.76%,在烟气和飞灰中的分配率波动较大,其分配率分别是14.176%~45.79%和9.78%~32.55%;Sb在烟气中的最大分配率为37.64%;温度升高反而会抑制As、Cu挥发,这与高温下As、Cu易与矿物质反应生成络合物有关。Ni、Cr、Mn属于难挥发重金属,绝大部分残留在炉渣中,且分配率对温度变化不敏感。赋存于炉渣中的Cr、Ni分别超过95%和97%;随着温度升高,Mn在炉渣中的分配率由71.46%增加到96.89%。     

Trace metal analysis of coal fly ash collected plain and on a quartz fibre filter

A simple, uniform procedure has been developed for microwave-based digestion of fly ash samples collected from the hoppers of an electrostatic precipitator (ESP), or collected from flue gases on a heat-resistant quartz fibre filter and for subsequent atomic absorption spectrometric analysis of trace metals (Be, Cd, Co, Cr, Cu, Mn, Ni, Pb, V and Zn). HNO₃, HCl, HF and mixtures have been tested as digestion acids. The combination of HNO₃ and HF has been found to be efficient for the digestion of fly ash samples with and without quartz fibre filter material. In spite of the complicated matrix, results with satisfactory accuracy and precision (relative standard deviation below 10% for most of the elements) have been obtained. In the case of analysis of fly ash together with a quartz fibre filter, the calibration curve has to be determined by standard addition to a blank solution containing a dissolved blank quartz fibre filter.     

The certification of the contents of Cd, Co, Cu, Fe, Hg, Ni, Pb, Zn, Sb, Se, Tl and Cr in a city waste incineration ash

Summary The analysis of ashes being of increasing importance, a reference material was prepared from fly ash of a city waste incinerator. The procedures of preparation, homogeneity and stability testing are described as well as the way of certification of elements of major importance: Cd, Co, Cr, Cu, Fe, Hg, Ni, Pb, Zn, Sb, Se and Tl.

---

Zertifizierung der Gehalte an Cd, Co, Cu, Fe, Hg, Ni, Pb, Zn, Sb, Se, Tl und Cr in einer Stadtmüll-Verbrennungsasche

Zusammenfassung Da die Analyse von Aschen zunehmend an Bedeutung gewinnt, wurde von der Flugasche einer Stadtmüll-Verbrennungsanlage ein Referenzmaterial hergestellt. Die Methoden der Herstellung sowie der Homogenitätsund Stabilitätsprüfung werden beschrieben und die Art der Zertifizierung der Elemente von hauptsächlicher Bedeutung aufgezeigt (Cd, Co, Cr, Cu, Fe, Hg, Ni, Pb, Zn, Sb, Se, Tl).

     

城市生活垃圾焚烧飞灰重金属的浸出特性

对用流化床焚烧炉混烧垃圾和煤的布袋飞灰进行了重金属的TCLP(Toxicity Characteristic Leaching Procedure)浸出特性实验，探讨了液固比、初始pH值及浸出时间对飞灰中重金属Pb、Cr、Cd、Ni、Cu、Zn的浸出影响。结果表明，重金属的浸出量都随着液固比的增加而增加，其中Cr、Cu一般呈上升趋势，Cd、Ni、Zn在液固比大于20时曲线变化较平缓，Pb的浸出规律比较特殊，有一个明显的波峰和波谷。重金属在浸取液的pH≤2.90时的浸出浓度远远大于pH≥4.03时的浸出浓度。Pb、Cr、Zn随着浸出时间的增加，浸出浓度下降，而Cd、Ni上升，Cu是先上升后下降。在液固比、初始pH值及浸出时间这三个影响因素中，pH值对重金属的浸出影响较大，重金属在酸性环境下较易浸出。     

城市污水污泥与固体垃圾混烧过程中重金属迁移特性的研究

通过城市污水污泥与固体垃圾合成样品在小型管式焚烧炉内的混烧实验,采集灰渣样品进行XRF化学成分分析和浸出毒性鉴别测试,结合污水污泥焚烧过程中热力学平衡计算,定量表征了污水污泥中Cu、Pb、Zn、 Mn、Ni在焚烧过程中向底灰、飞灰和烟气迁移的特性及对灰渣的毒性影响。研究结果表明,污水污泥混烧显著提高了飞灰和底灰中重金属含量,其中Zn和Pb增加量最大,而Ni、Mn、Cu依次减少;随着有机氯的加入,飞灰中重金属含量呈现递增趋势,其中Zn表现最明显。毒性测试结果显示,污水污泥的混烧也导致了垃圾焚烧飞灰中Zn和Pb的浸出浓度超过中国对危险废物浸出的控制标准值。同时,重金属迁移的热力学平衡模型预测结果与实验结果差距较大。这表明热力学平衡计算方法还需进一步考虑影响重金属氯化物形成的其他因素,如在焚烧过程中反应动力学、焚烧室内氧气含量变化、与其他元素间的化学反应等。     

固体添加剂对垃圾掺烧污泥焚烧飞灰高温过程中重金属挥发特性的影响

在研究垃圾与污泥掺烧后焚烧飞灰中重金属浸出特征的基础上,重点研究了飞灰在1 000 ℃条件下高温处置过程中重金属(Cu、Zn 、Pb、Cd)随不同停留时间的挥发特性及添加剂(CaO、Al₂O₃、SiO₂、高岭土、粉煤灰)对重金属转化与挥发特性的影响。研究结果表明,飞灰中重金属Zn、Pb、Mn含量较高,Ni的含量较低,而毒性较大的Cd达到29.4 mg/kg。浸出液中七种金属都满足危险废物鉴别标准(GB5085.3-1996),并且重金属的浸出浓度受浸取时间及浸取液pH值影响较大。在同样的高温处置条件下,焚烧飞灰中不同重金属的挥发特性有较大的差别。其中,Pb表现出易挥发的特性,其挥发率超过80%,而Cu挥发性较小,其挥发率小于30%。综合来看,飞灰中重金属的挥发性大小依次为Pb>Cd>Zn>Cu。飞灰中添加Al₂O₃和高岭土可以抑制Cd的挥发,添加Al₂O₃后Pb的挥发率有所减少,添加SiO₂、CaO、高岭土、粉煤灰均使Zn的挥发率降低,而对Cu的挥发率没有抑制作用,这与飞灰中高Cl含量及各痕量元素化合物对固体添加剂活性位选择性的竞争吸附有关。     

Molybdenum(VI) Oxide-Modified Silica Gel as a Novel Sorbent for the Simultaneous Solid-Phase Extraction of Eight Metals with Determination by Flame Atomic Absorption Spectrometry

A silica-based inorganic sorbent was synthesized by the thermal decomposition of ammonium heptamolybdate on silica and applied for the preconcentration and simultaneous determination of Cd, Co, Cr, Cu, Fe, Mn, Ni, and Pb in river water samples using a column system with flame atomic absorption spectrometry. Attenuated total reflection-Fourier transformation infrared spectroscopy, scanning electron microscopy, and electron dispersive spectroscopy were used for sorbent characterization. The effects of pH, sample volume, eluent type, eluent concentration, eluent volume, sample flow rate, and matrix ions (Al, Bi, Ca, Mg, and Zn) on the recovery of the metals in model solutions were investigated. The adsorption capacities (µmol g^?1) of SiO₂-MoO₃ were 88.96 (Cd), 169.69 (Co), 153.85 (Cr), 188.88 (Cu), 179.05 (Fe), 163.81 (Mn), 136.31 (Ni), and 38.61 (Pb). The detection limits of the method were 9.09, 10.82, 10.77, 49.57, 31.64, 6.40, 8.86, 19.15?µg L^?1 for Cd, Co, Cr, Cu, Fe, Mn, Ni, and Pb, respectively, with a preconcentration factor of 25. The developed method was used for the determination of the target metals in real samples and the recoveries for spiked samples were found to be from 91.2% to 102.9%.     

Trace metal analysis of coal fly ash collected plain and on a quartz fibre filter

A simple, uniform procedure has been developed for microwave-based digestion of fly ash samples collected from the hoppers of an electrostatic precipitator (ESP), or collected from flue gases on a heat-resistant quartz fibre filter and for subsequent atomic absorption spectrometric analysis of trace metals (Be, Cd, Co, Cr, Cu, Mn, Ni, Pb, V and Zn). HNO(3), HCl, HF and mixtures have been tested as digestion acids. The combination of HNO(3) and HF has been found to be efficient for the digestion of fly ash samples with and without quartz fibre filter material. In spite of the complicated matrix, results with satisfactory accuracy and precision (relative standard deviation below 10% for most of the elements) have been obtained. In the case of analysis of fly ash together with a quartz fibre filter, the calibration curve has to be determined by standard addition to a blank solution containing a dissolved blank quartz fibre filter.     

Certification of trace element contents (As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb and Zn) in a fly ash obtained from the combustion of pulverised coal

Summary The element contents of As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb und Zn of a fly ash from pulverised coal are certified. The procedures and their results for the homogenisation, the contamination and homogeneity checks and the analytical campaign are reported. The certified mass fractions and indicative values for Cr, Ni, Th, V and water soluble sulphate are given. The work was carried out within the framework of the activities of the Community Bureau of Reference (BCR) of the Commission of the European Communities.

---

Zertifizierung von Spurengehalten (As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb und Zn) in einer Flugasche aus Pulverkohle

Zusammenfassung In einer Flugasche aus Pulverkohle wurden die Elementgehalte an As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb und Zn zertifiziert. Über die Homogenisierung, die Kontrolle der Kontaminierung und Homogenität und die analytischen Ringversuche wird berichtet. Die zertifizierten Gehalte sowie der Gehalt von Cr, Ni, Th, V und wasserlöslichem Sulfat werden gegeben. Die Arbeit wurde ausgeführt im Rahmen des Programms des Referenzbüros der Kommission der Europäischen Gemeinschaften (BCR).

     

A Sequential Extraction Method Measures the Toxic Metal Content in Fly Ash from a Municipal Solid Waste Incinerator

The purpose of this research was to develop an optimized pretreatment procedure for toxic metals (Pb, Cd, Zn and Cu) content in fly ash from a municipal waste incinerator. In addition, modified sequential extraction procedures were used to characterize the chemical composition of the fly ash samples. The sequential extraction resolved the fly ash elements into the following chemical forms: soluble, exchangeable, carbonate, oxide, organic, and silicate compounds. Certified reference city waste incineration ash (BCR.176) was used as target ash samples. A H₂O₂+HNO₃+HF mixed acid digestion solution with a low temperature evaporation procedure was selected as optimal for the fly ash digestion. The digested solution was analyzed by inductively coupled plasma mass spectrometry (ICP‐MS), which effectively determined the concentrations of the toxic metal elements in BCR.176. Except for Cd, the recovery of Pb, Zn, and Cu under H₂O₂+HNO₃+HF digestion and their sequential extraction procedures were higher than 95%. The relative standard deviations (RSD) for recoveries of the four elements were within 10%. Furthermore, the sequential extraction procedure's results provided information on the potential mobility of the studied elements. Most of the Cd was bound to water‐soluble and carbonate material in the fly ash samples. Most of the Pb, Zn, and Cu was released to carbonates and bound to organic matter in the fly ash samples.     

Certification of the contents of some heavy metals (Cd, Cu, Hg, Ni, Pb and Zn) in three types of soils

Summary The element contents of Cd, Cu, Hg, Ni, Pb and Zn of three types of soil were certified. The preparation, homogeneity and stability are reported. The certified contents as well as values for Co, Cr, Mn and Se and for the aqua regia soluble contents Cd, Cr, Cu, Mn, Ni, Pb and Zn are given.

---

Zertifizierung von Schwermetallspuren (Cd, Cu, Hg, Ni, Pb und Zn) in drei Bodenproben

Zusammenfassung In drei verschiedenen Bodenproben wurden die Elementgehalte an Cd, Cu, Hg, Ni, Pb und Zn zertifiziert. Es wird berichtet über die Bereitung, Homogenität und Stabilität. Die zertifizierten Gehalte sowie der Gehalt an Cr, Co, Mn und Se und der Gehalt an königswasserlöslichem Cd, Cr, Cu, Mn, Ni, Pb und Zn werden angegeben.

     

Evaluation of a mixed chelator as heavy metal stabilizer for municipal solid‐waste incineration fly ash: Behaviors and mechanisms

This paper compares the stabilization performances of three dithiocarbamate and three phosphate chemical stabilizing agents, selects the best agents from each group, combines them as a mixed heavy metal stabilizer for municipal solid‐waste incineration (MSWI) fly ash, and investigates the effectiveness of the mixed chelator in stabilizing heavy metals in MSWI fly ash from southwest China. The mechanism of stabilization is also analyzed. Results indicate that piperazine dithiocarbamate can stabilize Cd, Cu, and Ni effectively, while sodium dihydrogen phosphate can stabilize Pb better. With the addition of the mixed chelator (2% sodium dihydrogen phosphate and 1% piperazine dithiocarbamate), all the targeted heavy metal concentrations in the leachate were below the standards for pollution control on municipal solid waste landfill sites in China. The stabilizing agents combined with the heavy metals in fly ash could not generate insoluble crystals; however, the heavy metals could combine with the agents' effective groups, generating flocs in the pores or on the surfaces of the fly ash and offering significant densification. The mixed chelator could transfer heavy metals from unstable fractions to stable fractions, so the leaching of heavy metals from the fly ash was greatly decreased.     

Principal component analysis: a chemometric aid for classification of polluted and unpolluted mussels

Ten trace elements (Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb) were determined in the dissolved ash of the edible part of wild mussels (28 samples) from a polluted site by electrothermal atomic absorption spectrometry. The distribution of the concentration of each element in the mussels was first investigated by means of a test of normality. The correlation matrix around the mean was used as a starting matrix for principal component analysis (PCA). Ten variables were reduced to two principal components, accounting for 77% of the total variance; Al, Cr, Mn, Fe, Zn, Cd and Pb are all positively associated with the first principal component and form a cluster of variables, indicating a common terrigenous origin. Comparison with 43 samples of unpolluted mussels from a nearby hatchery, on the basis of eight common variables (concentration of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb; 71 samples) by using a two-dimensional plot of PC scores, allows the mussels from the two sites to be differentiated.     

An integrated approach to the complete chemical analysis of magnesium or sodium diuranate (yellow cake) sample

A procedure for the complete chemical analysis of magnesium or sodium diuranate (yellow cake) sample is reported. Uranium is determined gravimetrically after peroxide precipitation. Optimum parameters, such as pH, quantity of hydrogen peroxide, volume of sample, temperature and complexing agent for quantitave precipitation of uranium, and effective separation of other elements were studied. Aluminum, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, and Zn were determined by flame atomic absorption spectrometer and B, Mo, SO₄, REEs and Y by inductively coupled plasma atomic emission spectrometer in the filtrates of hydroxide and peroxide precipitation separation. The proposed method is accurate and the precision is characterized by an RSD of ~0.2% for U; 2 to 6% for Mg, Na, K, Ca, Fe, SiO₂, Al, Cd, Co, Cr, Fe, Mn, Ni, Pb, and Zn and 3 to7% for REEs, Y, Mo and B     

Behaviour of inorganic constituents of municipal sewage sludge during fluidized-bed combustion

The fate of main heavy metals in municipal sewage sludge (As, Cd, Co, Cr, Cu, Hg, Mo, Ni, Pb, and Zn) was investigated using a fluidized-bed reactor. The behaviour of metals in the incinerator was explored by comparing metal contents in the two main ash streams: bottom (in-bed) ash and ash separated by a cyclone (cyclone-catch ash). All metals showed enrichment in the cyclone ash. The ash originating from sewage sludge is thermally quite stable consisting of quartz, hematite, spar(s), mica(s), apatite, and anhydrite. It does not soften nor becomes sticky and does not tend to agglomerate at temperatures up to 950°C.     

Inorganic species in water and sediments of the Lamone and Marzeno rivers ecosystem

Analytical results are reported for the determination of inorganic species in water and sediments sampled in the Lamone and Marzeno rivers ecosystem. The species determined are Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn, Hg, F-, Cl- Br-, NO3-, SO4--, Na+, K+, Mg++, Ca++, NH4+ in superficial water, and Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn, Hg in sediments. For all the elements, in addition to detection limits, precision and accuracy are given: the former, expressed as relative standard deviation (s(r)), and the latter, expressed as relative error (e), were good, being in all cases lower than 6%.     

生物质气化发电厂灰渣中微量元素的分布与富集规律

采用电感耦合等离子体发射光谱仪,研究了生物质气化发电厂灰渣中元素As、Al、Br、Ca、Cd、Cl、Cr、Cu、F、Fe、Ga、K、Mg、Mn、Na、Ni、P、Pb、S、Si、Sr、Ti、Zn在气化器底灰、淋洗器灰和旋风分离器灰中的质量分数,并分析了这些元素在不同粒径3种灰渣中的分布规律。结果表明,大部分极易挥发的元素,如卤族元素、碱金属元素主要在淋洗器中存在,表明了它们在飞灰颗粒中的富集。旋风分离器灰在灰渣中所占比例为10%左右,以粗灰为主,灰中Fe、Si、Ni、Pb、Zn、Cr、Cd为多;表明了此灰中重金属元素积累。在气化炉底灰中以K、S、Mn、Cu为主。元素随颗粒物粒径大小和元素性质的不同,呈现不同的富集规律。     

Determination of heavy metals in air conditioner dust using FAAS and INAA

The elements Cd, Cr, Cu, Mn, Ni, Pb and Zn were determined in dust samples collected from air conditioner (AC) filters from 15 commercial sites of Lahore using flame atomic absorption spectroscopy (FAAS). The elements Cr, Mn and Zn were also determined using instrumental neutron activation analysis (INAA). The results obtained showed that higher amounts of these metals were measured in these dust samples than normally found in soil. This was especially true for Cd, Cu, Pb and Zn. Generally the amounts of Cd, Cr and Mn did not vary throughout the city of Lahore but the amounts of the traffic related Cu, Pb and Zn elements had the more variable ranges of 30–140, 30–230 and 74–2810 mg/kg respectively. The concentrations obtained for Cr, Mn and Zn by INAA were found to be higher than those obtained using FAAS. Analysis of the data obtained showed the digestion procedure employed to be the possible cause for this occurrence. It was also found that Mn was being over-estimated by INAA due to the interference from the Mg peak.