基于交叉偏振波产生的脉冲净化技术研究与应用

本文利用交叉偏振波产生技术(XPW)对800 nm波段钛宝石飞秒激光器输出的激光脉冲进行时域净化, 提高脉冲时域对比度, 并测量验证了10¹¹对比度的脉冲, 达到测量仪器的动态范围极限, 比初始脉冲时域对比度有三个量级的提高, XPW的效率为22%. 同时发现净化后脉冲光谱宽度也得到一定展宽, 进一步利用啁啾镜对和补偿片对净化后的脉冲进行色散补偿, 得到25 fs脉宽的脉冲. 利用该净化后的激光脉冲作为种子注入已有的太瓦级钛宝石啁啾脉冲放大系统中, 在输出脉冲能量250 mJ, 宽度50 fs, 对应峰值功率5 TW的情况下, 在主脉冲前100 ps以外的范围内测量验证了10¹¹的脉冲对比度.     

饱和功率密度下线性啁啾对交叉偏振波输出特性的影响

交叉偏振波(XPW)技术是一种基于具有各向异性特征的三阶非线性晶体的非线性滤波技术,由于结构简单,稳定可靠,是超强超快激光领域提高时域对比度、压缩脉宽的有效手段之一.在实验中发现,XPW的输出特性受驱动脉冲特性的直接影响,通过理论计算得到了XPW的脉宽和光谱宽度与驱动脉冲的啁啾特性关系,同时利用声光可编程色散滤波器设计实验对理论计算进行了验证.结果表明:实验结果很好地反映了理论计算得出的结论,同时在饱和功率密度条件下,还表现出了一些理论计算没有反映出的新现象,即XPW的光谱展宽突破了驱动脉冲宽度√3倍的限制,最终脉宽也能够压缩至小于入射脉宽的1/√3;此外对于相反线性啁啾的驱动脉冲所产生的XPW信号,其在光谱形状上有明显的偏移差异,同时输出效率也有所不同.最后对这些新现象进行了进一步的分析和理论解释.     

10(-10) temporal contrast for femtosecond ultraintense lasers by cross-polarized wave generation

We take advantage of nonlinear properties associated with chi(3) tensor elements in BaF2 cubic crystal to improve the temporal contrast of femtosecond laser pulses. The technique presented is based on cross-polarized wave (XPW) generation. We have obtained a transmission efficiency of 10% and 10(-10) contrast with an input pulse in the millijoule range. This filter does not affect the spectral shape or the phase of the cleaned pulse. It also acts as an efficient spatial filter. In this method the contrast enhancement is limited only by the extinction ratio of the polarization discrimination device.     

非真空传输的高效交叉偏振滤波设计与产生

采用常规透镜设计了适用于非真空环境中交叉偏振波(XPW)产生的双透镜聚焦系统,在相对较短的距离实现了长焦透镜聚焦的效果,并测量了聚焦后的激光脉冲,发现其没有显著的非线性相位积累,保证了激光光束质量.在非真空中采用双BaF_2晶体得到了XPW系统转换效率22%,光谱1.78倍展宽的净化脉冲输出,双透镜组合聚焦形式使得双BaF_2晶体间距在13—22 cm内可保证20%以上的XPW转换效率,双晶体间距的调节冗余度提高了两个量级,极大地降低了双晶转换效率对晶体间距的依赖.这种正负透镜组合聚焦的光路设计在非真空中实现了高效稳定的XPW输出,为后续的放大应用提供了高对比度、宽光谱的高质量种子源.     

High-peak power multi-wavelength picosecond pulses generated from a BaWO4 Raman-seeded optical parametric amplifier

We report the generation of high-peak power multi-wavelength picosecond laser pulses using optical parametric amplification (OPA) in BBO seeded with pulses generated in a 5-mm length BaWO₄ crystal by stimulated Raman scattering of 18-ps laser pulses at 532 nm. The maximum output energy of the amplified first-Stokes component at 559.7 nm was about 1.76 mJ. The corresponding maximum peak power, pulse duration and spectral line width were measured to be 117.3 MW, 15 ps and 18.0 cm⁻¹, respectively. The multi-wavelength picosecond laser pulses were in the visible and near infrared ranges. Using this Raman-seeded OPA technique, the beam quality of the stimulated Raman scattering pulses can be improved.     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

Effects of electron relaxation on multiple harmonic generation from metal surfaces with femtosecond laser pulses

Calculations are presented for the first four (odd and even) harmonics of an 800 nm laser from a gold surface, with pulse widths ranging from 100 down to 14 fs. For peak laser intensities above 1 GW/cm² the harmonics are enhanced because of a partial depletion of the initial electron states. At 10¹¹ W/cm² of peak laser intensity the calculated conversion efficiency for 2nd-harmonic generation is 3 × 10⁻⁹, while for the 5th-harmonic it is 10⁻¹⁰. The generated harmonic pulses are broadened and delayed relative to the laser pulse because of the finite relaxation times of the excited electronic states. The finite electron relaxation times cause also the broadening of the autocorrelations of the laser pulses obtained from surface harmonic generation by two time-delayed identical pulses. Comparison with recent experimental results shows that the response time of an autocorrelator using nonlinear optical processes in a gold surface is shorter than the electron relaxation times. This seems to indicate that for laser pulses shorter than ∼30 fs, the fast nonresonant channel for multiphoton excitation via continuum-continuum transitions in metals becomes important as the resonant channel becomes slow (relative to the laser pulse) and less efficient.     

Influence of spectral phase on cross-polarized wave generation with short femtosecond pulses

In this paper we present the first comprehensive study of the role of spectral phase on cross-polarized wave (XPW) generation using sub-30 femtosecond (fs) laser pulses. XPW generation improves the temporal contrast and shortens the pulse duration of fs chirped pulse amplification (CPA) lasers. For Ti:Sa lasers, compression below 30?fs is non-trivial and therefore never perfect. We therefore systematically analyze the effect of an arbitrary input spectral phase on the output spectrum and efficiency of the XPW process, both theoretically and experimentally. We derive the maximum acceptable value of residual phase for a given initial pulse duration in order to efficiently drive the XPW process for pulse shortening and contrast improvement.     

Nanosecond laser damage resistance of differently prepared semi-finished parts of optical multimode fibers

Optical multimode fibers are applied in materials processing (e.g. automotive industry), defense, aviation technology, medicine and biotechnology. One challenging task concerning the production of multimode fibers is the enhancement of laser-induced damage thresholds. A higher damage threshold enables a higher transmitted average power at a given fiber diameter or the same power inside a thinner fiber to obtain smaller focus spots.In principle, different material parameters affect the damage threshold. Besides the quality of the preform bulk material itself, the drawing process during the production of the fiber and the preparation of the fiber end surfaces influence the resistance. Therefore, the change of the laser-induced damage threshold of preform materials was investigated in dependence on a varying thermal treatment and preparation procedure.Single and multi-pulse laser-induced damage thresholds of preforms (F300, Heraeus) were measured using a Q-switched Nd:YAG laser at 1064 nm wavelength emitting pulses with a duration of 15 ns, a pulse energy of 12 mJ and a repetition rate of 10 Hz. The temporal and spatial shape of the laser pulses were controlled accurately.Laser-induced damage thresholds in a range from 150 J cm⁻² to 350 J cm⁻² were determined depending on the number of pulses applied to the same spot, the thermal history and the polishing quality of the samples, respectively.     

交叉偏振滤波技术提高飞秒超强激光信噪比的研究

对交叉偏振波滤波技术理论分析的基础上,在"极光-III"装置中采用该技术进行了钛宝石飞秒放大激光脉冲对比度提高的实验研究,不仅显著的抑制了纳秒范围内再生放大器产生的预脉冲,而且也将皮秒范围内的信噪比由10^-5提高到了10^-7,实验测得基波到交叉偏振波的转化效率大于10%.研究表明,该技术可以有效地提高飞秒超强激光的信噪比.     

Electrically actuated elastomers for electro–optical modulators

We demonstrate the technique of cross-polarized wave (XPW) generation at 1 μm with a 310-fs optical parametric chirped-pulse amplification system at the millijoule level. We show an improvement of the temporal contrast by three orders of magnitude with an energy transmission of 22%. Additionally, we report that XPW generation preserves the beam spatial quality and shortens the pulse duration by a factor of 3^1/2, resulting in a peak power transmission of ∼35%. PACS 42.65.Re; 42.65.Yj; 42.70.Mp     

Nonlinear spectral cleaning effect in cross-polarized wave generation

The underlying mechanism of the spectral cleaning effect of the cross-polarized wave(XPW) generation process was theoretically investigated. This study shows that the spectral noise of an input spectrum can be removed in the XPW generation process and that the spectral cleaning effect depends on the characteristics of the input pulses, such as the chirp and Fourier-transform-limited duration of the initial pulse, and the modulation amplitude and frequency of the spectral noise. Though these factors codetermine the output spectrum of the XPW generation process, the spectral cleaning effect is mainly affected by the initial pulse chirp. The smoothing of the spectrum in the XPW generation process leads to a significant enhancement of the coherent contrast.     

Nonlinear optical absorption studies of an organo-metallic complex by Z-scan technique

An organo-metallic complex, [(CH₃)₄N][Ni(dmit)₂] (dmit²⁻ = (1,3-dithiole-2-thione-4,5-dithiolate), abbreviated as MeNi, is synthesized. The nonlinear optical absorption properties of MeNi dissolved in acetone have been studied using the open-aperture Z-scan technique with 40 ps pulse width at 1064 nm and 1 ns, 15 ns pulse width at 1053 nm, respectively. Strong saturable absorption has been found when the sample solution is irradiated by 40 ps and 1 ns laser pulses. While irradiated with 15 ns laser pulse, a stronger reverse saturable absorption has been found. The nonlinear optical absorption coefficients are −1.03 × 10⁻¹¹ m/W, −1.85 × 10⁻¹¹ m/W and 3.84 × 10⁻¹⁰ m/W, respectively. The mechanism responsible for the difference between the results is analyzed. All the results suggest that this material may be a promising candidate for the application to laser pulse compression in the near-infrared waveband.     

Recombination emissions and spectral blueshift of pump radiation from ultrafast laser induced plasma in a planar water microjet

We report spectroscopic investigations of an ultrafast laser induced plasma generated in a planar water microjet. Plasma recombination emissions along with the spectral blueshift and broadening of the pump laser pulse contribute to the total emission. The laser pulses are of 100 fs duration, and the incident intensity is around 10¹⁵ W/cm². The dominant mechanisms leading to plasma formation are optical tunnel ionization and collisional ionization. Spectrally resolved polarization measurements show that the high frequency region of the emission is unpolarized whereas the low frequency region is polarized. Results indicate that at lower input intensities the emission arises mainly from plasma recombinations, which is accompanied by a weak blueshift of the incident laser pulse. At higher input intensities strong recombination emissions are seen, along with a broadening and asymmetric spectral blueshift of the pump laser pulse. From the nature of the blueshifted laser pulse it is possible to deduce whether the rate of change of free electron density is a constant or variable within the pulse lifetime. Two input laser intensity regimes, in which collisional and tunnel ionizations are dominant respectively, have been thus identified.     

Self-Q-switched and mode-locked 946 nm Cr,Nd:YAG laser

A simultaneous self-Q-switched and mode-locked diode-pumped 946 nm laser by using a Cr,Nd:YAG crystal as gain medium as well as saturable absorber is demonstrated for the first time as we know. The maximum average output power of 751 mW with a slope efficiency of 18.38% is obtained at an intra-cavity average peak power intensity of 4.83 × 10⁶ W/cm². Under this circumstance, the repetition rate of Q-switched envelopes is 9.63 kHz and the pulse width is about 460 ns. Almost 100% mode-locked modulation depth is obtained at all time in the experiment process whether the incident pump power is low or high. The repetition rate of mode-locked pulses within a Q-switched envelope is 135.13 MHz and the mode-locked pulse width is within 600 ps. The laser produces high-quality pulses in TEM₀₀-mode in the simultaneous self-Q-switched and mode-locked experiment.     

Optical and ultrasonic monitoring of femtosecond laser filamentation in fused silica

Millimeter-long filaments and accompanying luminous plasma and defect channels created in fused silica (FS) by single focused femtosecond laser pulses with supercritical powers were probed in situ using optical imaging and contact ultrasonic techniques. Above the threshold pulse energy E_opt = 5 μJ corresponding to a few megawatt power levels pulses collapse due to self-focusing, producing channels filled by electron-hole plasma and luminescent defects, and exhibits predominantly compressive pressure transients. Analysis of the optical and ultrasonic response versus the laser pulse energy suggests that filamentary pulse propagation in the channels occurs with considerable dissipation of about ∼10 cm⁻¹. The predominant ionization mechanism is most likely associated with avalanche ionization, while the main mechanism of optical absorption is free-carrier absorption via inverse Bremsstrahlung interaction with the polar lattice.     

Ytterbium femtosecond fiber laser without dispersion compensation tunable from 1015 nm to 1050 nm

We report on a widely tunable ytterbium fs-fiber laser without dispersion compensation. The all-normal dispersion laser contains a spectral filter for wavelength tuning and for generating additional amplitude modulation to support the nonlinear polarization evolution as mode-locking mechanism. By tilting the interference filter the center wavelength of the laser can be tuned from 1015 nm to 1050 nm with a pulse energy up to 2.0 nJ. The pulses can be dechirped externally to 108 fs.     

Self-Q-switched and mode-locked Nd,Cr:YAG laser with 6.52-W average output power

Simultaneous self-Q-switched and mode-locked have been demonstrated in a diode-pumped Nd,Cr:YAG laser. For the first time as we know, almost 100% modulation depth has been achieved at an intracavity intensity of 5.6 × 10⁵ W/cm². The maximum average output power of 6.52 W corresponding to a slope efficiency of 30% is obtained at 1064 nm. The laser produces high-quality pulses in a TEM₀₀-mode at the pump power of 16.5 W. The pulse duration of the mode-locked pulses is about 600 ps with 136 MHz repetition rate.     

Effects of laser operating parameters on metals micromachining with ultrafast lasers

180 femtoseconds (1 kHz) and 10 picoseconds (1-50 kHz) ultrafast laser micro-structuring of the metals Ti alloy, Al and Cu have been studied for the purpose of industrial application. The effects of some key laser operating parameters were investigated. The evolution of surface morphology revealed that laser pulses overlap in a range around the spatial FWHM can help to achieve optimal residual surface roughness. While observed ablation rate (unit: μm³ per pulse) changed dramatically with repetition rate due to the combined effects of plasma absorption, residual thermal energy and phase transition, higher throughput can be achieved with higher repetition rate. This study also indicated that residual surface roughness is almost independent of repetition rate at 10 ps temporal pulse length. The ablation depth is approximately proportional to the number of overscan; however, machining accuracy deteriorates, especially for femtosecond laser processing and metals with low thermal conductivity and short electron-phonon coupling time.     

Detection of scattered light pulses at femto-Joule level by using a picosecond BBO optical parametric amplifier

We report a technique for detecting weak scattered light pulses based on a 532 nm pumped picosecond β-barium-borate collinear optical parametric amplifier. The measured maximum slope gain factor of the amplifier was found to be around 10⁷, and the energy detection limit was of the order of fJ/pulse for the signal of 730 nm and the idler of 1.5 μm at a pumping intensity of 2.83 GW/cm². The linearity of the gain for this amplifier was found to be excellent for a seeding level of lower than 420 fJ per pulse. The maximum gains and the energy detection limits for the scattered light pulses from various scattering targets were found to be poorer than that from the reflective mirror, owing to the degraded beam quality and the depolarization of the scattered light. A reduction of the maximum gain for the scattered light with the increase of the angle of incidence, which causes pulse broadening and reduces the photon flux of the signal, was investigated. The feasibility of detecting weak scattered light in the infrared by using idler-to-signal frequency up-conversion was also demonstrated, in which the infrared seeder located in the idler branch of the amplifier was injected as the seeding beam and was then parametrically up-converted into the visible signal branch, with an even higher gain.