Vacancy profiles and clustering in light-ion-implanted GaN and ZnO

We present experimental results obtained in H-implanted GaN and He- and Li-implanted ZnO. The ion energies were varied in the range 100-850 keV, and the implantation fluences in the range 5 × 10¹³ to 1 × 10¹⁸ cm⁻². In addition, conventional and flash anneals at temperatures 500-1400 °C were performed on the ZnO samples. The data obtained with a slow positron beam show that vacancy clusters are formed in as-implanted samples with fluences above 1 × 10¹⁷ cm⁻². Below this value only single vacancies are detected after implantation, but vacancy clusters can be formed and subsequently dissociated by thermal annealings.     

Optical waveguide with homogeneous refractive index profile in LiNbO3 by double-low-energy Oxygen ion implantation

We report on the formation of the planar waveguide by 550 keV O ion followed by 250 keV O ion implantation in lithium niobate (LiNbO₃), at fluences of 6 × 10¹⁴ ions/cm² and 3 × 10¹⁴ ions/cm², respectively. The Rutherford backscattering/channeling spectra have shown the atomic displacements in the damage region before and after annealing. A broad and nearly homogeneous damage layer has been formed by double-energy ion implantation after annealing. Both the dark mode spectra and the data of refractive index profile verified that the extraordinary refractive index was enhanced in the ion implanted region of LiNbO₃. A homogeneous near-field intensity profile was obtained by double-low-energy ion implantation. There is a reasonable agreement between the simulated modal intensity profile and the experimental data. The estimated propagation loss is about 0.5 dB/cm.     

Damage formation in Ge during Ar and He implantation at 15 K

Ar⁺ and He⁺ ions were implanted into Ge samples with (1 0 0), (1 1 0), (1 1 1) and (1 1 2) orientations at 15 K with fluences ranging from 1×10¹¹ to 1×10¹⁴ cm⁻² for the Ar⁺ ions and fluences ranging from 1×10¹² to 6×10¹⁵ cm⁻² for the He⁺ ions. The Rutherford backscattering (RBS) technique in the channelling orientation was used to study the damage built-up in situ. Implantation and RBS measurements were performed without changing the target temperature. The samples were mounted on a four axis goniometer cooled by a close cycle He cryostat. The implantations were performed with the surface being tilt 7° off the ion beam direction to prevent channelling effects. After each 300 keV Ar⁺ and 40 keV He⁺ implantation, RBS analysis was performed with 1.4 MeV He⁺ ions.For both the implantation ions, there is about no difference between the values found for the damage efficiency per ion for the four different orientations. This together with the high value (around 5 times higher than that found in Si), gives rise to the assumption of amorphous pocket formation per incident ion, i.e. direct impact amorphization, already at low implantation fluences. At higher fluences, when collision cascades overlap, there is a growth of the already amorphized regions.     

Investigations of He implantation and subsequent annealing effects in InP

The influence of 70 keV He⁺ ion implantation and subsequent annealing of Cz-indium phosphide (InP) samples has been investigated using a slow positron beam-based Doppler broadening spectrometer. Three samples with ion fluences of 1 × 10¹⁶, 5 × 10¹⁶ and 1 × 10¹⁷ cm⁻² were studied in the as-implanted condition as well as after annealing at 640 °C for times between 5 and 40 min. It was found that the line-shape parameter of the positron-electron annihilation peak in the implanted layer increases after 5 min annealing, then after longer annealing times it starts to decline gradually until it reaches a value close to the value of the as-grown sample. This implies that vacancy-like defects can be created in InP by He implantation followed by short-thermal annealing at T > 600 °C. Comparison of the results with a study where cavities were observed in He-implanted InP has been carried out.     

Marker experiments to determine diffusing species and diffusion path in medical Nitinol alloys

The out-diffusion of toxic Ni ions from NiTi (Nitinol), often used for biomedical applications, can be strongly reduced using oxygen plasma immersion ion implantation (PIII). Non-radioactive isotope markers, ⁶⁰Ni and ⁴⁶Ti, were implanted at 180 keV into NiTi prior to the oxygen implantation with fluences between 0.4 × 10¹⁶ and 4 × 10¹⁶ at./cm². Implanting oxygen ions by PIII in the temperature range of 400-550 °C leads to a surface oxide layer consisting of pure TiO₂. The results prove that Ni cations are the mobile species, while Ti is immobile during the oxygen insertion.     

Effect of copper ions implantation on corrosion behavior of zircaloy-4 in 1 M H2SO4

In order to study the effect of copper ion implantation on the aqueous corrosion behavior, samples of zircaloy-4 were implanted with copper ions with fluences ranging from 1 × 10¹⁶ to 1 × 10¹⁷ ions/cm², using a metal vapor vacuum arc source (MEVVA) operated at an extraction voltage of 40 kV. The valence states and depth distributions of elements in the surface layer of the samples were analyzed by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES), respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the copper ion implantation. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted zircaloy-4 in a 1 M H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zircaloy-4 implanted with copper ions when the fluence is smaller than 5 × 10¹⁶ ions/cm². The corrosion resistance of implanted samples declined with increasing the fluence. Finally, the mechanism of the corrosion behavior of copper-implanted zircaloy-4 was discussed.     

Ferromagnetism in ZnO doped with Co by ion implantation

The importance of doping ZnO with magnetic ions is associated with the fact that this oxide is a good candidate for the formation of a magnetic-diluted semiconductor. Most of the studies reported in Co-doped ZnO were carried out in thin films, but the understanding of the modification of the magnetic behaviour due to doping demands the study of single-crystalline samples. In this work, ZnO single crystals were doped at room temperature with Co by ion implantation with fluences ranging between 2×10¹⁶ and 1×10¹⁷ ions cm⁻² and implantation energy of 100 keV. As implanted samples show a superparamagnetic behaviour attributed to the formation of Co clusters, room temperature ferromagnetism is attained after annealing at 800 °C, but no magnetoresistance was detected in the temperature range from 10 to 300 K.     

Effect of thermal treatment on linear optical properties of Cu nanoclusters

Silica glass was implanted with 50 keV Cu⁺ ions at various fluences from 6×10¹⁵ to 8×10¹⁶ ions/cm² and thermally-annealed in air between room temperature to 1200 °C. UV/visible spectroscopy measurements reveal absorption bands at characteristics surface plasmon resonance (SPR) frequencies, signifying the formation of copper colloids in silica, even without thermal treatments. Such copper nanoclusters can be attributed to the relatively high mobility of copper atoms, even at ambient conditions. Using the equation derived from the framework of free-electron theory, the average radii of the Cu particles were found to be in the range 2-4 nm from the experimental surface plasmon absorption peaks. Radioluminescence (RL) spectra exhibited broad bands at 410 and 530 nm, associated with the presence of Cu⁺ ions in the as-implanted samples. The effect of thermal annealing in air on absorption and emission spectra of these Cu-implanted samples, as well as the formation of copper nanoclusters from original Cu⁺ ions, is discussed.     

Ion irradiation induced Al-Ti interaction in nano-scaled Al/Ti multilayers

Interactions induced in Al/Ti multilayers by implantation of Ar ions at room temperature were investgated. Initial structures consisted of (Al/Ti) × 5 multilayers deposited by d.c. ion sputtering on Si(1 0 0) wafers, to a total thickness of ∼250 nm. They were irradiated with 200 keV Ar⁺ ions, to the fluences from 5 × 10¹⁵ to 4 × 10¹⁶ ions/cm². It was found that ion irradiation induced a progressed intermixing of the multilayer constituents and Al-Ti nanoalloying for the highest applied fluence. The resulting nanocrystalline structure had a graded composition with non-reacted or interdiffused Al and Ti, and γ-AlTi and AlTi₃ intermetallic phases. Most intense reactivity was observed around mid depth of the multilayers, where most energy was deposited by the impact ions. It is presumed that Al-Ti chemical reaction is triggered by thermal spikes and further enhanced by chemical driving forces. The applied processing can be interesting for fabrication of tightly bond multilayered structures with gradual changes of their composition and properties.     

Luminescence properties of Tb implanted ZnO

ZnO [0 0 0 1] crystals were irradiated at room temperature with Tb⁺ ions of 400 keV with fluences from 1×10¹⁶ to 2×10¹⁷ cm⁻². The implanted layer was examined by several methods, including radioluminescence (RL), Rutherford backscattering spectrometry (RBS) and optical spectroscopy. The optical extinction spectra were simulated using Mie scattering theory. Absorption spectra predicted by Mie theory for particles of decreasing diameter were compared with those obtained experimentally. Some qualitative agreement between theoretical and experimental data was achieved. It was also shown that the intensities of the characteristic green emission bands associated with Tb produced by ⁵D₄→⁷F_j=5,4 transitions have increased about 8 times after annealing. Optical spectroscopy and radioluminescence data have revealed that the ion implantation is a promising tool for synthesizing Tb nanoparticles in the ZnO surface. The Tb nanoparticles exhibit a rather weak plasma resonance.     

Surface modification of poly(propylene carbonate) by oxygen ion implantation

Poly(propylene carbonate) (PPC) was implanted by oxygen ion with energy of 40 keV. The influence of experimental parameters was investigated by varying ion fluence from 1 × 10¹² to 1 × 10¹⁵ ions/cm². XPS, SEM, surface roughness, wettability, hardness, and modulus were employed to investigate structure and properties of the as-implanted PPC samples. Eight chemical groups, i.e., carbon, CH, COC, CO, OCO, CO, , and groups were observed on surfaces of the as-implanted samples. The species and relative intensities of the chemical groups changed with increasing ion fluence. SEM images displayed that irradiation damage was related strongly with ion fluence. Both surface-recovering and shrunken behavior were observed on surface of the PPC sample implanted with fluence of 1 × 10¹⁵ ions/cm². As increasing ion fluence, the surface roughness of the as-implanted PPC samples increased firstly, reached the maximum value of 159 nm, and finally decreased down the minimum value. The water droplet contact angle of the as-implanted PPC samples changed gradually with fluence, and reached the minimum value of 70° with fluence of 1 × 10¹⁵ ions/cm². The hardness and modulus of the as-implanted PPC samples increased with increasing ion fluence, and reached their corresponding maximum values with fluence of 1 × 10¹⁵ ions/cm². The experimental results revealed that oxygen ion fluence closely affected surface chemical group, morphology, surface roughness, wettability, and mechanical properties of the as-implanted PPC samples.     

Slow positron beam study of nitrogen implanted CZ-Si subjected to rapid thermal processing

In this experiment, nitrogen ions were implanted into CZ-silicon wafer at 100 keV at room temperature with the fluence of 5 × 10¹⁵ N₂⁺/cm², followed by rapid thermal processing (RTP) at different temperatures. The single detector Doppler broadening and coincidence Doppler broadening measurements on slow positron beam were carried out to characterize the defects in the as-implanted silicon and RTP-treated samples. It is found that both nitrogen-vacancy complexes (N-Vsi) and oxygen-vacancy complexes (O-Vsi) produced by nitrogen implantation diffuse back to the sample surface upon annealing. But the N-Vsi and the O-Vsi complete with each other and give a summed effect on positron annihilation characteristics. It is shown that the N-Vsi win out the O-Vsi in as-implanted sample and by RTP at 650 °C, 750 °C, which make the S-parameter increase; O-Vsi plays a dominant role after annealing above 850 °C, which makes the S parameter decrease.     

Synthesis of molybdenum silicide by both ion implantation and ion beam assisted deposition

Two groups of Mo/Si films were deposited on surface of Si(1 0 0) crystal. The first group of the samples was prepared by both ion beam assisted deposition (IBAD) and metal vapor vacuum arc (MEVVA) ion implantation technologies under temperatures from 200 to 400 °C. The deposited species of IBAD were Mo and Si, and different sputtering Ar ion densities were selected. The mixed Mo/Si films were implanted by Mo ion with energy of 94 keV, and fluence of Mo ion was 5 × 10¹⁶ ions/cm². The second group of the samples was prepared only by IBAD under the same test temperature range. The Mo/Si samples were analyzed by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), sheet resistance, nanohardness, and modulus of the Mo/Si films were also measured. For the Mo/Si films implanted with Mo ion, XRD results indicate that phase of the Mo/Si films prepared at 400 and 300 °C was pure MoSi₂. Sheet resistance of the Mo/Si films implanted with Mo ion was less than that of the Mo/Si films prepared without ion implantation. Nanohardness and modulus of the Mo/Si films were obviously affected by test parameters.     

Structure and micro-mechanical properties of helium-implanted layer on Ti by plasma-based ion implantation

The present paper concentrates on structure and micro-mechanical properties of the helium-implanted layer on titanium treated by plasma-based ion implantation with a pulsed voltage of −30 kV and doses of 3, 6, 9 and 12 × 10¹⁷ ions/cm², respectively. X-ray photoelectron spectroscopy and transmission electron microscopy are employed to characterize the structure of the implanted layer. The hardnesses at different depths of the layer were measured by nano-indentation. We found that helium ion implantation into titanium leads to the formation of bubbles with a diameter from a few to more than 10 nm and the bubble size increases with the increase of dose. The primary existing form of Ti is amorphous in the implanted layer. Helium implantation also enhances the ingress of O, C and N and stimulates the formations of TiO₂, Ti₂O₃, TiO, TiC and TiN in the near surface layer. And the amount of the ingressed oxygen is obviously higher than those of nitrogen and carbon due to its higher activity. At the near surface layer, the hardnesses of all implanted samples increases remarkably comparing with untreated one and the maximum hardness has an increase by a factor of up to 3.7. For the samples implanted with higher doses of 6, 9 and 12 × 10¹⁷ He/cm², the local displacement bursts are clearly found in the load-displacement curves. For the samples implanted with a lower dose of 3 × 10¹⁷ He/cm², there is no obvious displacement burst found. Furthermore, the burst width increases with the increase of the dose.     

Fabrication and evolution of Cu nanoparticles in Al2O3 crystal by ion implantation and annealing at different atmospheres

Single crystal Al₂O₃ samples were implanted with 45 keV Cu ion implantation at a dose of 1 × 10¹⁷ ions/cm², and then subjected to furnace annealing in vacuum or with a flow of oxygen gas. Various techniques, such as ultraviolet-visible spectroscopy, X-ray diffraction spectroscopy and atomic force microscopy, have been used to investigate formation of Cu NPs and their evolution. Our results clearly show that the evolution of Cu NPs depends strongly on annealing atmosphere in the temperature range up to 600 °C. Annealing in vacuum only gives rise to a slight change in the size of Cu NPs. No evidence for oxidization of Cu NPs has been revealed. Remarkable modifications in Cu NPs, including the size increase and the effective transformation into CuO NPs, have been observed for the samples annealed at oxygen atmosphere. The results have been tentatively discussed in combination with the role of oxygen from atmosphere in diffusion of Cu atoms towards the surface and its interactions with Cu NPs during annealing.     

Bioactivity of Mg-ion-implanted zirconia and titanium

Titanium and zirconia are bioinert materials lacking bioactivity. In this work, surface modification of the two typical biomaterials is conducted by Mg-ion-implantation using a MEVVA ion source in an attempt to increase their bioactivity. Mg ions were implanted into zirconia and titanium with fluences ranging from 1 × 10¹⁷ to 3 × 10¹⁷ ions/cm² at 40 keV. The Mg-implanted samples, as well as control (unimplanted) samples, were immersed in SBF for 7 days and then removed to identify the presence of calcium and phosphate (Ca-P) coatings and to characterize their morphology and structure by SEM, XRD, and FT-IR. SEM observations confirm that globular aggregates are formed on the surfaces of the Mg-implanted zirconia and titanium while no precipitates are observed on the control samples. XRD and FT-IR analyses reveal that the deposits are carbonated hydroxyapatite (HAp). Our experimental results demonstrate that Mg-implantation improves the bioactivity of zirconia and titanium. Further, it is found that the degree of bioactivity is adjustable by the ion dose. Mechanisms are proposed to interpret the improvement of bioactivity as a result of Mg implantation and the difference in bioactivity between zirconia and titanium.     

Ion implantation induced by Cu ablation at high laser fluence

High energy laser plasma-produced Cu ions have been implanted in silicon substrates placed at different distances and angles with respect to the normal to the surface of the ablated target. The implanted samples have been produced using the iodine high power Prague Asterix Laser System (PALS) using 438 nm wavelength irradiating in vacuum a Cu target. The high laser pulse energy (up to 230 J) and the short pulse duration (400 ps) produced a non-equilibrium plasma expanding mainly along the normal to the Cu target surface. Time-of-flight (TOF) technique was employed, through an electrostatic ion energy analyzer (IEA) placed along the target normal, in order to measure the ion energy, the ion charge state, the energy distribution and the charge state distribution. Ions had a Boltzmann energy distributions with an energy increasing with the charge state. At a laser fluence of the order of 6 × 10⁶ J/cm², the maximum ion energy was about 600 keV and the maximum charge state was about 27+.In order to investigate the implantation processes, Cu depth profiles have been performed with Rutherford backscattering spectrometry (RBS) of 1.5 MeV helium ions, Auger electron spectroscopy (AES) with 3 keV electron beam and 1 keV Ar sputtering ions in combination with scanning electron microscopy (SEM). Surface analysis results indicate that Cu ions are implanted within the first surface layers and that the ion penetration ranges are in agreement with the ion energy measured with IEA analysis.     

Reflectivity modification of polymethylmethacrylate by silicon ion implantation

The effect of silicon ion implantation on the optical reflection of bulk polymethylmethacrylate (PMMA) was examined in the visible and near UV. A low-energy (30 and 50 keV) Si⁺ beam at fluences in the range from 10¹³ to 10¹⁷ cm⁻² was used for ion implantation of PMMA. The results show that a significant enhancement of the reflectivity from Si⁺-implanted PMMA occurs at appropriate implantation energy and fluence. The structural modifications of PMMA by the silicon ion implantation were characterized by means of photoluminescence and Raman spectroscopy. Formation of hydrogenated amorphous carbon (HAC) layer beneath the surface of the samples was established and the corresponding HAC domain size was estimated.     

Surface nano-structural modifications and characteristics in nitrogen ion implanted W as a function of temperature and N energy

The surface modifications of tungsten massive samples (0.5 mm foils) made by nitrogen ion implantation are studied by SEM, XRD, AFM, and SIMS. Nitrogen ions in the energy range of 16-30 keV with a fluence of 1 × 10¹⁸ N⁺ cm⁻² were implanted in tungsten samples for 1600 s at different temperatures. XRD patterns clearly showed WN₂ (0 1 8) (rhombohedral) very close to W (2 0 0) line. Crystallite sizes (coherently diffracting domains) obtained from WN₂ (0 1 8) line, showed an increase with substrate temperature. AFM images showed the formation of grains on W samples, which grew in size with temperature. Similar morphological changes to that has been observed for thin films by increasing substrate temperature (i.e., structure zone model (SZM)), is obtained. The surface roughness variation with temperature generally showed a decrease with increasing temperature. The density of implanted nitrogen ions and the depth of nitrogen ion implantation in W studied by SIMS showed a minimum for N⁺ density as well as a minimum for penetration depth of N⁺ ions in W at certain temperatures, which are both consistent with XRD results (i.e., I_{W (2 0 0)}/I_{W (2 1 1)}) for W (bcc). Hence, showing a correlation between XRD and SIMS results.     

Enhanced photoluminescence of Ar implanted sapphire before and after annealing

In this paper, we studied the changes in the photoluminescence spectra of the Ar⁺ ion implanted mono-crystalline sapphire annealed at different atmospheres and different temperatures. Single crystals of sapphire (Al₂O₃) with the (1 0 1¯ 0) (m-samples) orientation were implanted at 623 K with 110 keV Ar⁺ ions to a fluence of 9.5×10¹⁶ ions/cm². Photoluminescence measurement of the as-implanted sample shows a new emission band at 506 nm, which is attributed to the production of interstitial Al atoms. The intensity of emission band at 506 nm first increased then decreased with increase in annealing temperature. For the same annealing temperature, the intensity of PL peak at 506 nm of the sample annealed in air was higher than the sample annealed in vacuum. The experimental results show that the intensity of the PL peak at 506 nm of Ar-implanted sapphire can be enhanced by subsequent annealing with an enhancement of nearly 20 times. The influence of thermal annealing of the Ar-implanted samples on the new 506 nm emission band was discussed.