Effect of doping MnO2 on magnetic properties for M-type barium ferrite

The crystalline structure and magnetic properties of M-type barium ferrite doped with small amounts of MnO₂ (0, 0.25, 0.5, 0.75, 1.0, 1.5, and 2.0 wt%, respectively) have been investigated by means of XRD, SEM and VSM. The results show that the crystalline structures of barium ferrite are still M-type hexagonal structure and Mn ions are distributed homogeneously in both the grains and the grain boundaries. The saturation magnetization and magnetocrystalline anisotropy constants both reach the highest values when x=0.75 wt%. The displacement of Fe ions from 4f₁ to 2b site is mainly responsible for the appearance of the maximum values.     

Low-temperature sintering of M-type barium ferrite with BaCu(B2O5) additive

The aim of this work is to lower the sintered temperature of M-type barium ferrite (BaM) by BaCu(B₂O₅) (BCB) additives. The effects of BCB additives on the sintering behavior, structure and magnetic properties of BaM were also discussed. It was found that the sintered density, saturation magnetization and initial permeability of BaM are modified obviously as small amount of BCB (1-4 wt%) is added. Especially, when BaM with 3 wt% BCB was sintered at 900 °C, the single-phase BaM was obtained and showed excellent properties with sintered density of 4.88 g/cm³, saturation magnetization of 61.4 emu/g and initial permeability of 3.15. In addition, the SEM result revealed that the sample can be co-fired well with the Ag electrode at 900 °C. The reason for this was attributed to be the formation of the BCB liquid phase. It suggests that this M-type barium ferrite can be used as LTCC substrate for millimeter wave circulator, filter and other magnetic microwave devices.     

Magnetic and electrical properties of bulk BaTiO3+MgFe2O4 composite

BaTiO₃+MgFe₂O₄ material system was synthesized by hybrid chemical process using chlorides and nitrates of barium, titanium, iron, and magnesium. Magnetic properties of the composite samples measured as a function of annealing conditions indicated soft magnetic behavior. Saturation specific magnetization from 8 21 emu/g was observed for samples annealed at temperature between 950 and 1150 °C. Variation of specific saturation magnetization with respect to annealing temperature was related with the distribution of Fe cations in the tetrahedral and octahedral sites of MgFe₂O₄. Electrical properties of the samples annealed at different temperatures were measured to analyze the coexistence of ferroelectric phase. Dielectric constant varying from 15 to 200 with respect to frequency was observed for samples annealed from 950 to 1150 °C.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

Structural and magnetic properties of sol-gel Co2xNi0.5−x Zn0.5−xFe2O4 thin films

Nanocrystalline Co_2xNi_0.5−xZn_0.5−xFe₂O₄ (x=0−0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform without microcracks. The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size independent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe₂O₄. The maximum absorption band shifted from 13 to 11 GHz as cobalt content increased from x=0.1 to 0.2.     

Structural, microstructural and magnetic properties of NiFe2O4, CoFe2O4 and MnFe2O4 nanoferrite thin films

The structural, microstructural and magnetic properties of nanoferrite NiFe₂O₄ (NF), CoFe₂O₄ (CF) and MnFe₂O₄ (MF) thin films have been studied. The coating solution of these ferrite films was prepared by a chemical synthesis route called sol-gel combined metallo-organic decomposition method. The solution was coated on Si substrate by spin coating and annealed at 700 °C for 3 h. X-ray diffraction pattern has been used to analyze the phase structure and lattice parameters. The scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used to show the nanostructural behavior of these ferrites. The values of average grain's size from SEM are 44, 60 and 74 nm, and from AFM are 46, 61 and 75 nm, respectively, measured for NF, CF and MF ferrites. At room temperature, the values of saturation magnetization, M_s∼50.60, 33.52 and 5.40 emu/cc, and remanent magnetization, M_r∼14.33, 15.50 and 1.10 emu/cc, respectively, are observed for NF, CF and MF. At low temperature measurements of 10 K, the anisotropy of ferromagnetism is observed in these ferrite films. The superparamagnetic/paramagnetic behavior is also confirmed by χ′(T) curves of AC susceptibility by applying DC magnetizing field of 3 Oe. The temperature dependent magnetization measurements show the magnetic phase transition temperature.     

Crystallization-dependent magnetic properties of Mn1.56Co0.96Ni0.48O4 thin films

The effects of magnetic property dependence of the Mn_1.56Co_0.96Ni_0.48O₄ (MCN) films on crystallization are investigated in the growth temperature of 450-750 °C. With the growth temperature increase, both the crystalline quality and the grain size improve. The MCN films exhibit paramagnetic to ferromagnetic transition and the paramagnetic parts fit to the modified Curie-Weiss law. The ferromagnetic couplings of the magnetic ions in the MCN films enhance at elevated growth temperature. The saturation magnetization at 5 K increases with increasing growth temperature, but coercive field decreases monotonously. The magnetic properties of the MCN films strongly depend on their microstructures.     

Synthesis and characterization of TiO2 thin films coated on metal substrate

Nanostructured titanium dioxide (TiO₂) thin films have been prepared on metal substrates using a facile layer-by-layer dip-coating method. The phase structure and morphologies of preparing samples were characterized by means of X-ray powder diffraction (XRD) and field-emission scanning electron microscopy (FESEM). The results confirm that films are highly crystalline anatase TiO₂ and free from other phases of titanium dioxide. Scanning electron microscopy (SEM) shows that the nanoparticles are sintered together to form a compact structure. The electrical properties of samples were investigated by cutternt-voltage analysis, the result indicates that a rectifying junction between the nanocrystalline TiO₂ film and metal substrate was formed. The photoelectrochemical characteristics recorded under 1.5 AM illumination indicates that the as-fabricated thin film electrode possesses the highest photocurrent density at 450 °C, which is 1.75 mA/cm² at 0 V vs. Ag/AgCl.     

Assembly of high-anisotropy L10 FePt nanocomposite films

In this paper we report results on the synthesis and magnetic properties of L1₀ FePt nanocomposite films. Three fabrication methods have been developed to produce high-anisptropy FePt films: non-epitaxial growth of (0 0 1)-oriented FePt:X (X=Ag, C) composite films that might be used for perpendicular media; monodispersed FePt(CF_x) core–shell nanocluster-assembled films grown with a gas-aggregation technique and having uniform cluster size and narrow size distribution; and template-mediated self-assembled FePt clusters prepared with chemical synthesis by a hydrogen reduction technique, which has a high potential for controlling both cluster size and orientation. The magnetic properties are controllable through variations in the nanocluster properties and nanostructure. Analytical and numerical simulations have been done for these films, providing better understanding of the magnetization reversal mechanisms. The films show promise for development as magnetic recording media at extremely high areal densities.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

Structural characterization and optical properties of UO2 thin films by magnetron sputtering

Uranium dioxide films were deposited on Si (1 1 1) substrates by dc magnetron sputtering method at different sputtering parameters. The structure, morphology and chemical state of the films were studied by field emission scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. Influences of film thickness on the microstructure and optical properties were investigated. Experimental results show that the film crystallites are preferentially oriented with the (1 1 1) planes. The average grain size increases with increasing film thickness. AFM images show that the root mean square roughness of the films is between 1.2 nm and 2.1 nm. Optical constants (refractive index, extinction coefficient) of the films in the wavelength range of 350-1000 nm are obtained by ellipsometric spectroscopy. The result shows that the refractive index decreases with the increasing film thickness, while extinction coefficient increases with the film thickness.     

Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba0.7Sr0.3Tio3) thin films

Ferroelectric barium strontium titanate (Ba_0.7Sr_0.3TiO₃)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂]_, strontium 2-ethylhexanoate [Sr[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂] and titanium(IV) isopropoxide [TiOCH(CH₃)₂]₄ precursors using a modified sol-gel technique. The precursor except [TiOCH(CH₃)₂]₄ were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 °C for 1 h in air. The lattice constants “a” and “c” were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 °C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency (∼95%), which decreases slightly after crystallization (∼90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.     

Electromagnetic and microwave absorption properties of Fe3O4 magnetic films plated on hollow glass spheres

Magnetic hollow spheres of low density were prepared by plating Fe₃O₄ magnetic films on hollow glass spheres using ferrite plating. The complex permeability and permittivity of spheres–wax composites were measured in the range of 2–18 GHz. The complex permeability and permittivity increased, and the dielectric and magnetic losses were improved as the volume fraction of the magnetic spheres in the composites increased from 60% to 80%, which also resulted in a great improvement of microwave absorption properties. For composites with volume fraction 80%, its magnetic resonance frequency was at about 13 GHz and it appeared three loss peaks in the calculated reflection loss curves; the bandwidth less than −10 dB was almost 4 GHz which was just in the Ku-band frequencies (12–18 GHz) and a minimum reflection loss of −20 dB was obtained when the thickness was 2.6 mm; the microwave absorbing properties were mainly due to the magnetic loss. The results showed that the magnetic spheres composites were good and light microwave absorbers in the Ku-band frequencies.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

Structure,magnetic properties and magnetostriction of Fe81Ga19 thin films

The structure, magnetic properties and magnetostriction of Fe₈₁Ga₁₉ thin films have been investigated by using X-ray diffraction analysis, scanning electron microscope (SEM), vibrating sample magnetometer and capacitive cantilever method. It was found that the grain size of as-deposited Fe₈₁Ga₁₉ thin films is 50–60 nm and the grain size increases with increase in the annealing temperature. The remanence ratio (M_r/M_s) of the thin films slowly decreases with increase in the annealing temperature. However, the coercivity of the thin films goes the opposite way with increase in the annealing temperature. A preferential orientation of the Fe₈₁Ga₁₉ thin film fabricated under an applied magnetic field exists along 〈1 0 0〉 direction due to the function of magnetic field during sputtering. An in-plane-induced anisotropy of the thin film is well formed by the applied magnetic field during the sputtering and the formation of in-plane-induced anisotropy results in 90° rotations of the magnetic domains during magnetization and in the increase of magnetostriction for the thin film.     

Low temperature fired Ni-Cu-Zn ferrite with Bi4Ti3O12

The Ni-Cu-Zn ferrites with different contents of Bi₄Ti₃O₁₂ ceramics (1-8 wt%) as sintering additives were prepared by the usual ceramic technology and sintered at 900 °C to adapt to the low temperature co-fired ceramic (LTCC) technology. The magnetic and dielectric properties of the ferrite can be effectively improved with the effect of an appropriate amount of Bi₄Ti₃O₁₂. For all samples, the ferrite sintered with 2 wt% Bi₄Ti₃O₁₂ has relatively high density (98.8%) and permeability, while the ferrite with 8 wt% Bi₄Ti₃O₁₂ has relatively good dielectric properties in a wide frequency range. The influences of Bi₄Ti₃O₁₂ addition on microstructure, magnetic and dielectric properties of the ferrite have been discussed.     

Synthesis and characterization of hard magnetic composites—Hollow microsphere/titania/barium ferrite

Hard magnetic composites—hollow microsphere (core)/titania (intermediate layer)/barium ferrite (magnetic shell) (M/T/B) were prepared by wet-chemical method. Barium ferrite nanoparticles were directly coated on the rutile titania-coated hollow microsphere forming light hard magnetic composites using sol-gel technique. The prepared composites were characterized with FESEM, EDS, XRD and vibrating sample magnetometry. The composites are composed of barium ferrite, hematite, titania and mullite. For the samples with 40 wt.% barium ferrite, its specific saturation magnetization with titania is increased to 17.88 emu/g in comparison with 9.6 emu/g without titania. The function of titania in the composites is also discussed.     

Phase formation and change of magnetic properties in mechanical alloyed Ni0.5Co0.5Fe2O4 by annealing

The effects of milling time and annealing temperature on phase formation, microstructure and magnetic properties of nickel-cobalt ferrite synthesized from oxide precursors by mechanical alloying were studied. The study of milling time effects on phase formation of milled materials showed that if milling continues up to 55 h, single phase nano-sized nickel-cobalt ferrite is obtained. Also, magnetic properties of powders versus milling time and annealing at different temperatures extensively changed, so that annealing at 1200 °C increased the magnetization saturation of the as-milled powder from 15.1 to 53.6 emu/g. X-ray powder diffraction technique (XRD) with Cu-Ka radiation was employed for phase identification. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were also used to determine the morphology and size of the particles. The magnetic properties were measured by a vibration sample magnetometer (VSM).     

The effect of B2O3 addition to the microstructure and magnetic properties of Ni0.4Zn0.6Fe2O4 ferrite

The effects of 0.01 and 0.1 mol B₂O₃ addition to the microstructure and magnetic properties of a Ni–Zn ferrite composition expressed by a molecular formula of Ni_0.4Zn_0.6Fe₂O₄ were investigated. The toroid-shaped samples prepared by pressing the milled raw materials used in the preparation of the composition were sintered in the range of 1000–1300 °C. The addition of 0.01 mol B₂O₃ increased the grain growth and densification giving rise to reduced intergranular and intragranular porosity due to liquid-phase sintering. The sintered toroid sample at 1300 °C gave the optimum magnetic properties of B_r=170 mT, H_c=0.025 kA/m and a high initial permeability value of μ_i=4000. The increment of the B₂O₃ content to 0.1 mol resulted in a pronounced grain growth and also gave rise to large porosity due to the evaporation of B₂O₃ at higher sintering temperatures. Hence, it resulted in an air-gap effect in the hysteresis curves of these samples.     

Coupling of magnetostriction and electrostriction in the porous rheological composite

The production method of the elastic composite containing ferrous particles and titanium barium particles dispersed in the porous silicone matrix is described in this article. Since it contains ferrous and titanium barium particles, this composite shows magnetorheological and also electrorheological properties. The electrostriction of composite samples in the electric field with maximal intensity 1.5×10⁶ V/m was investigated. The magnetostriction in the magnetic field with maximal induction 1 T was also investigated. It was found that samples elongate with increased electric field intensity, and the magnetic field induction was detected. By increasing the samples’ elongation with increase of ferrous particles, titanium barium particles and pores number were also detected. In the investigated division of the electric and magnetic field the elongation changed in a linear way. The maximal elongation achieved was 1.59%.