Complex thermal evolution of size-stabilized tetragonal zirconia

Zirconia nanopowder with doping YO_1.5 contents between 0 and 1 mol% were synthesized by the Pechini method. The crystallite dimensions of the powder, around 10 nm, allows for the size stabilization of the tetragonal polymorph over the thermodynamically stable monoclinic one. As the nanopowders are heated to 1200 °C and subsequently cooled back to room temperature, a complex evolution of the phase composition occurs. Upon heating the tetragonal phase transforms slowly into the monoclinic one and the transition cannot be completed before entering the stability range of the tetragonal phase (above 1150 °C). Upon cooling, on the other hand, the reaction is considerably faster and the complete transformation into the monoclinc phase occurs in a narrow temperature range. Rietveld analysis of the high temperature X-ray patterns revealed as, during heating, the transition is mainly controlled by microstructural parameters and in particular it is triggered by the release of RMS microstrain. Upon cooling, on the other hand, the transition is kinetically controlled by the doping content.     

The phase transitions and ferroelectric behavior of dense nanocrystalline BaTiO3 ceramics fabricated by pressure assisted sintering

Dense nanocrystalline BaTiO₃ ceramics with uniform grain sizes of 30 nm was obtained by pressure assisted sintering. The phase transitions were investigated by Raman scattering at temperatures ranging from −190 to 200 °C. With increasing temperature, similar to 3 μm BaTiO₃ normal ceramics, the successive phase transitions from rhombohedral to orthorhombic, orthorhombic to tetragonal, tetragonal to cubic were also observed in 30 nm BaTiO₃ ceramics. Especially, the coexistence of ferroelectric tetragonal and orthorhombic phases was found at room temperature. The ferroelectric behavior was further characterized by P-E hysteresis loop. The experimental results indicate that the critical grain size of the disappearance of ferroelectricity in nanocrystalline BaTiO₃ ceramics fabricated by pressure assisted sintering is below 30 nm.     

Low temperature perovskite phase formation in PCT 90/10 system by modified chemical route

Perovskite phase development study of PCT 90/10 system was carried out. Modified chemical technique was used for synthesis. Single perovskite phase with a polycrystalline tetragonal structure was obtained in PCT 90/10 ceramic system at 600 °C processing temperature. Dense packing of grains with average grain size ∼1 μm was observed in PCT 90/10 ceramic samples. Curie transition temperature (T_c) of PCT 90/10 ceramic samples was found to be ∼180 °C with diffuse phase transition.     

Phase transition and magnetic properties of Mg-doped hexagonal close-packed Ni nanoparticles

Mg-doped Ni nanoparticles with the hexagonal close-packed (hcp) and face-centered cubic (fcc) structure have been synthesized by sol-gel method sintered at different temperatures in argon atmosphere. The sintering temperature played an important role in the control of the crystalline phase and the particle size. The pure hcp Mg-doped Ni nanoparticles with average particle size of 6.0 nm were obtained at 320 °C. The results indicated that the transition from the hcp to the fcc phase occurred in the temperature range between 320 °C and 450 °C. Moreover, the VSM results showed that the hcp Mg-doped Ni nanoparticles had unique ferromagnetic and superparamagnetic behavior. The unsaturation even at 5000 Oe is one of the superparamagnetic characteristics due to the small particle size. From the ZFC and FC curves, the blocking temperature T_B of the hcp sample (6.0 nm) was estimated to be 10 K. The blocking temperature was related to the size of the magnetic particles and the magnetocrystalline anisotropy constant. By theoretical calculation, the deduced particle size was 6.59 nm for hcp Mg-doped Ni nanoparticles which was in agreement with the results of XRD and TEM.     

In situ observations of temperature- and pressure-induced phase transitions in TiH2: Angle-dispersive and synchrotron energy-dispersive X-ray diffraction studies

We investigated the behavior of the structure of titanium hydride (TiH₂), an important compound in hydrogen storage research, at elevated temperatures (0-120 °C) and high pressures (1 bar-34 GPa). Temperature-induced changes of TiH₂ as indicated in the alteration of the ambient X-ray demonstrated a cubic to tetragonal phase transition occurring at about 17 °C. The main focus of this study was to identify any pressure-induced structural transformations, including possible phase transitions, in TiH₂. Synchrotron X-ray diffraction studies were carried out in situ (diamond anvil cell) in a compression sequence up to 34 GPa and in subsequent decompression to ambient pressure. The pressure evolution of the diffraction patterns revealed a cubic (Fm-3m) to tetragonal (I4/mmm) phase transition at 2.2 GPa. The high-pressure phase persisted up to 34 GPa. After decompression to ambient conditions the observed phase transition was completely reversible. A Birch-Murnaghan fit of the unit cell volume as a function of pressure yielded a zero-pressure bulk modulus K₀=146(14) GPa, and its pressure derivative K′₀=6(1) for the high-pressure tetragonal phase of TiH₂.     

Monolayer deposition of L10 FePt nanoparticles via electrospray route

The deposition monolayers of L1₀ FePt nanoparticles via an electrospraying method and the magnetic properties of the deposited film were studied. FePt nanoparticles in a size of around 2.5 nm in diameter, prepared by a liquid process, were used as a precursor. The size of the deposited particles can be controlled up to 35 nm by controlling the sprayed droplet size that is formed by adjusting the precursor concentration and the precursor flow rate. The droplets were heated in a tubular furnace at a temperature of up to 900 °C to remove all organic compounds and to transform the FePt particles from disordered face centered cubic to an ordered FCT phase. Finally, the particles were deposited in the form of a monolayer film on a silicon substrate by electrostatic force and characterized by scanning electron microscopy. The monolayer of particles was obtained by the high charge on particles obtained during the electrospraying process. The magnetic properties of the monolayer were investigated by magneto-optic Kerr effect measurements. Coercivity up to 650 Oe for a film consisting of 35 nm L1₀ FePt nanoparticles was observed after heat treatment at a temperature of 800 °C.     

Light-induced ultrafast phase transitions in VO2 thin film

Vanadium dioxide shows a passive and reversible change from a monoclinic insulator phase to a metallic tetragonal rutile structure when the sample temperature is close to and over 68 °C. As a kind of functional material, VO₂ thin films deposited on fused quartz substrates were successfully prepared by the pulsed laser deposition (PLD) technique. With laser illumination at 400 nm on the obtained films, the phase transition (PT) occurred. The observed light-induced PT was as fast as the laser pulse duration of 100 fs. Using a femtosecond laser system, the relaxation processes in VO₂ were studied by optical pump-probe spectroscopy. Upon a laser excitation an instantaneous response in the transient reflectivity and transmission was observed followed by a relatively longer relaxation process. The alteration is dependent on pump power. The change in reflectance reached a maximum value at a pump pulse energy between 7 and 14 mJ/cm². The observed PT is associated with the optical interband transition in VO₂ thin film. It suggests that with a pump laser illuminating on the film, excitation from the d_θ,? - state of valence band to the unoccupied excited mixed d_θ,?-π* - state of the conduction band in the insulator phase occurs, followed by a resonant transition to an unoccupied excited mixed d_θ,?-π* - state of the metallic phase band.     

Investigation of thermal annealing effects on microstructural and optical properties of HfO2 thin films

In the present paper, we investigate the effect of thermal annealing on optical and microstructural properties of HfO₂ thin films (from 20 to 190 nm) obtained by plasma ion assisted deposition (PIAD). After deposition, the HfO₂ films were annealed in N₂ ambient for 3 h at 300, 350, 450, 500 and 750 °C. Several characterisation techniques including X-ray reflectometry (XRR), X-ray diffraction (XRD), spectroscopic ellipsometry (SE), UV Raman and FTIR were used for the physical characterisation of the as-deposited and annealed HfO₂ thin films. The results indicate that as-deposited PIAD HfO₂ films are mainly amorphous and a transition to a crystalline phase occurs at a temperature higher than 450 °C depending on the layer thickness. The crystalline grains consist of cubic and monoclinic phases already classified in literature but this work provides the first evidence of amorphous-cubic phase transition at a temperature as low as 500 °C. According to SE, XRR and FTIR results, an increase in the interfacial layer thickness can be observed only for high temperature annealing. The SE results show that the amorphous phase of HfO₂ (in 20 nm thick samples) has an optical bandgap of 5.51 eV. Following its transition to a crystalline phase upon annealing at 750 °C, the optical bandgap increases to 5.85 eV.     

Internal stresses and stability of the tetragonal phase in zirconia thin layers deposited by OMCVD

Zirconia thin films were deposited by OMCVD (organo-metallic chemical vapour deposition) at various temperatures and oxygen partial pressures on a AISI 301 stainless steel substrate with Zr(thd)₄ as precursor. The as deposited 250 nm thin zirconia films presented a structure consisting of two phases: the expected monoclinic one and also an unexpected tetragonal phase. According to the literature, the stabilization of the tetragonal phase (metastable in massive zirconia) can be related to the crystallite size and/or to the generated internal compressive stresses.To analyze the effect of internal and external stresses on the thin film behaviour, in-situ tensile experiments were performed at room temperature and at high temperature (500 °C).Depending on the process parameters, phase transformations and damage evolution of the films were observed. Our results, associated to XRD (X-ray diffraction) analyses, used to determine phase ratios and residual stresses within the films, before and after the mechanical experiments, are discussed with respect to their microstructural changes.     

Thermally responsive wettability of self-assembled methylcellulose nanolayers

Thermo-responsive cellulosic nanolayers were prepared from methylcellulose (MC), which is known to have a unique lower critical solution temperature. Thiosemicarbazide (TSC) was selectively introduced into the MC reducing end groups, and the corresponding MC-TSC derivative was spontaneously chemisorbed on an Au substrate at 4 °C to give MC self-assembled monolayers (SAMs). Linear MC chains were stably fixed onto the Au substrate, yielding an MC-SAM of thickness ca. 15 nm with a root mean square value less than 1 nm. The MC-SAM surface exhibited thermally responsive wetting characteristics; the water contact angle was found to rise and fall around 70 °C, possibly due to the solid-state phase transition of the MC nanolayers resulting from the inherent gelation of MC molecules in water. Such wetting behavior was shown to be reversible following repeated heating and cooling. The MC-SAM immersed in salt solution revealed lower phase transition temperatures, and an increase in sodium chloride concentration ranging from 0.0 to 1.0 M brought about a dramatic decrease in the apparent phase transition temperature from ca. 70 to 30 °C. For the purposely designed MC nanolayers, such controllable wetting properties are expected to prompt growing interest in the applications of cellulosic biopolymer interfaces.     

Effects of annealing temperature on the structural and photoluminescence properties of nanocrystalline ZrO2 thin films prepared by sol-gel route

Highly transparent nanocrystalline zirconia thin films were prepared by the sol-gel dip coating technique. XRD pattern of ZrO₂ thin film annealed at 400 °C shows the formation of tetragonal phase with a particle size of 13.6 nm. FT-IR spectra reveal the formation of Zr-O-Zr and the reduction of OH and other functional groups as the temperature increases. The transmittance spectra give an average transmittance greater than 80% in the film of thickness 262 nm. Photoluminescence (PL) spectra give intense band at 391 nm and a broad band centered at 300 nm. The increase of PL intensity with elevation of annealing temperature is related to reduction of OH groups, increase in the crystallinity and reduction in the non-radiative related defects. The luminescence dependence on defects in the film makes it suitable for luminescent oxygen-sensor development. The “Red shift” of excitation peak is related to an increase in the oxygen content of films with annealing temperature. The “Blue shift” of PL spectra originates from the change of stress of the film due to lattice distortion. The defect states in the nanocrystalline zirconia thin films play an important role in the energy transfer process.     

Effect of post-annealing on the properties of copper oxide thin films obtained from the oxidation of evaporated metallic copper

Thin films of copper oxide were obtained through thermal oxidation (100-450 °C) of evaporated metallic copper (Cu) films on glass substrates. The X-ray diffraction (XRD) studies confirmed the cubic Cu phase of the as-deposited films. The films annealed at 100 °C showed mixed Cu-Cu₂O phase, whereas those annealed between 200 and 300 °C showed a single cubic Cu₂O phase. A single monoclinic CuO phase was obtained from the films annealed between 350 and 450 °C. The positive sign of the Hall coefficient confirmed the p-type conductivity in the films with Cu₂O phase. However, a relatively poor crystallinity of these films limited the p-type characteristics. The films with Cu and CuO phases show n-type conductivity. The surface of the as-deposited is smooth (RMS roughness of 1.47 nm) and comprised of uniformly distributed grains (AFM and SEM analysis). The post-annealing is found to be effective on the distribution of grains and their sizes. The poor transmittance of the as-deposited films (<1%) is increased to a maximum of ∼80% (800 nm) on annealing at 200 °C. The direct allowed band gap is varied between 2.03 and 3.02 eV.     

Economical synthesis of nanocrystalline alumina using an environmentally low-cost binder

Sol-gel, a commonly used technique, involves the formation of an amorphous gel from a precursor solution. In this research nanocrystalline alumina powders have been synthesized through a new sol-gel simplified method. The route involved using an environmentally low-cost binder and aluminum nitrate in an aqueous medium. The added metal ions were dispersed in the gelled binder matrix. The gelled mass was dried and characterized by simultaneous thermogravimetric and differential thermal analysis (TG-DTA) and calcined at 350, 400, 530, 650, and 900 °C for 2 h. The samples were evaluated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The used binder can be applied to form a perfect matrix for the entrapment of metal ions that during heat treatment, gives rise to ultrafine amorphous or crystalline alumina particles. In this study, the transition phases of alumina with particle sizes of 15-25 nm as well as aluminum oxide hydrate phase were produced by the heat treatment of the gelled mass at temperature 650 °C. By increasing the calcinations temperature to 900 °C, alumina transition phases were changed and aluminum oxide hydrate eliminated. The particle sizes at this temperature were obtained in the range 15-30 nm. The particle size and crystallite size of products measured from XRD and TEM were in good agreement.     

Effect of growth temperature on the morphology and bonded states of SnO2 nanobaskets

The nanobaskets of SnO₂ were grown on in-house fabricated anodized aluminum oxide pores of 80 nm diameter using plasma enhanced chemical vapor deposition at an RF power of 60 W. Hydrated stannic chloride was used as a precursor and O₂ (20 sccm) as a reactant gas. The deposition was carried out from 350 to 500 °C at a pressure of 0.2 Torr for 15 min each. Deposition at 450 °C results in highly crystalline film with basket like (nanosized) structure. Further increase in the growth temperature (500 °C) results in the deterioration of the basket like structure and collapse of the alumina pores. The grown film is of tetragonal rutile structure grown along the [1 1 0] direction. The change in the film composition and bonded states with growth temperature was evident by the changes in the photoelectron peak intensities of the various constituents. In case of the film grown at 450 °C, Sn 3d_5/2 is found built up of Sn⁴⁺ and O-Sn⁴⁺ and the peaks corresponding to Sn²⁺ and O-Sn²⁺ were not detected.     

Preparation and optical properties of barium titanate thin films

Barium titanate (BTO) films were prepared by sol-gel spin-coating technique. The crystal structure and optical properties of BTO films have been investigated. The results indicate that the BTO films are single perovskite phase having tetragonal symmetry. The band gap of the BTO films increases with the increasing of layer number and decreasing of solution concentration. The transmittance and band gap of the BTO films annealed at 900 °C is more than that of the BTO films annealed at 700 °C when wavelength is 200-1000 nm. When wavelength is 400-1000 nm, the absorption coefficient α obtained by experiment is higher than that obtained by calculation (close to zero).     

Structural, electrical and optical properties of ZnS films deposited by close-spaced evaporation

ZnS films have been deposited on glass substrates by close-spaced evaporation (CSE) technique. The films were grown at different temperatures in the range, 200-350 °C. The layers have been characterized with X-ray diffractometer (XRD), atomic force microscope (AFM), energy dispersive analysis of X-rays (EDAX) and optical spectrophotometer to evaluate the quality of the layers for photovoltaic applications. The studies showed that the optimum substrate temperature for the growth of ZnS layers was 300 °C. The films grown at these temperatures exhibited cubic structure with nearly stoichiometric composition. The AFM data revealed that the films had nano-sized grains with a grain size of ∼40 nm. The optical studies exhibited direct allowed transition with an energy band gap of 3.61 eV. The other structural and optical parameters such as lattice stress, dislocation density, refractive index and extinction coefficient were also evaluated. The temperature-dependent conductivity measured in the range, 303-523 K showed a change in the conduction mechanism at 120 °C. The activation energy values evaluated using the temperature dependence of electrical conductivity are 7 and 29 meV at low and high temperature regions, respectively.     

Large scale intercalated growth of short aligned carbon nanotubes among vermiculite layers in a fluidized bed reactor

Short aligned carbon nanotubes (CNTs) were intercalated grown among vermiculite layers from ethylene using a simple fluidized bed chemical vapor deposition (CVD) process. The length of CNTs ranged from 0.5 to 1.5 μm after a synthesizing duration of 1-5 min at 650 °C. The as-grown CNTs vertically aligned to the vermiculite layers were with the mean outer and inner diameter of 6.7 and 3.7 nm, respectively. A CNT yield of 0.22 g/g_cat was obtained for a 5-min growth. Those indicated that the fluidized bed CVD was an effective way for mass production of short CNTs.     

Microstructural and compositional studies of liquid-phase deposition derived PbTiO3 thin films on LaNiO3 substrates

PbTiO₃ thin films were successfully deposited on the LaNiO₃ (LNO) substrates by the liquid-phase deposition (LPD) method and post-annealing at various temperatures. The structure, morphology and composition of the films were investigated by some analytical techniques. The as-deposited films are amorphous and composed of densely packed spherical particles. The films with the grain size of 180 nm start to decompose and crystallize into perovskite structure at 450 °C and show a perovskite single phase with tetragonal structure after annealing at 650 °C. X-ray photoelectron spectroscopy (XPS) analysis reveals that the as-deposited film contains fluorine and carbon as major impurities. Fluorine could be completely eliminated by annealing at 650 °C in air.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

High-temperature B2 ordering in Fe50Co50 alloy

High-temperature (above 1200 °C) B2 ordering was experimentally found in the Fe₅₀Co₅₀ alloy with the help of the electron diffraction. Using the X-ray photoelectron spectroscopy method the “ordering-phase separation” transition was shown to lead to changes both in the 3d-electron spectra of the valence band (3d-valence electron localization on Fe atoms increases at phase separation and it decreases at ordering). The investigation of multiplet splitting of the 3s-electron spectra of core-level electrons reveals that magnetic moments on Fe and Co atoms in the Fe₅₀Co₅₀ alloy are larger, when there is the tendency toward ordering, and they are smaller in the case of the tendency toward phase separation. A number of examples are presented, which are indicative of the fact that chemical ordering can influence magnetic ordering by the formation of the respective microstructures and magnetic ordering has no influence on chemical ordering. It can be concluded that the phase transition “ordering-phase separation” takes place both at 730 °C and at the temperature somewhat higher that 1200 °C.