Synthesis and Characterization of a Block Copolymer Containing Regioregular Poly(3‐hexylthiophene) and Poly(γ‐benzyl‐L‐glutamate)

Poly(3‐hexylthiophene)‐b‐poly(γ‐benzyl‐L ‐glutamate) (P3HT‐b‐PBLG) rod–rod diblock copolymer was synthesized by a ring‐opening polymerization of γ‐benzyl‐L ‐glutamate‐N‐carboxyanhydride using a benzylamine‐terminated regioregular P3HT macroinitiator. The opto‐electronic properties of the diblock copolymer have been investigated. The P3HT precursor and the P3HT‐b‐PBLG have similar UV–Vis spectra both in solution and solid state, indicating that the presence of PBLG block does not decrease the effective conjugation length of the semiconducting polythiophene segment. The copolymer displays solvatochromic behavior in THF/water mixtures. The morphology of the diblock copolymer depends upon the solvent used for film casting and annealing results in morphological changes for both films deposited from chloroform and trichlorobenzene.

     

Poly(3‐hexylthiophene) films prepared using binary solvent mixtures

Binary solvent mixtures were routinely used to induce the hierarchical assembly of poly(3‐hexylthiophene) (P3HT) in the liquid phase. This technique has garnered a lot of interest as a route to well‐organized films and composites, but, to date, the impact that the attributes of the liquid‐phase aggregates and solvent mixtures have on the organization of the films have only been partially scrutinized. The molecular weight and concentration dependence of P3HT assembly in three binary solvent mixtures containing chloroform and acetonitrile, n‐hexane, or dichloromethane were studied using ultraviolet/visible absorbance spectroscopy and dynamic light scattering techniques. Films drop cast under slow and rapid evaporation conditions were observed using optical and atomic force microscopy. In general, there is no evidence that the characteristics of the liquid phase P3HT aggregates impact the structures of the films, but films cast from these solvent mixtures under rapid evaporation conditions exhibit an array of disparate morphologies and mesoscale patterning. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 624–638     

Reduced Graphene Oxide/Poly(3‐hexylthiophene) Supramolecular Composites

Poly(3‐hexylthiophene) (P3HT) supramolecular structures are fabricated on P3HT‐dispersed reduced graphene oxide (RGO) monolayers and surfactant‐free RGO monolayers. P3HT is able to disperse RGO in hot anisole/N,N‐dimethylformamide solvents, and forms nanowires on RGO surfaces through a RGO induced crystallization process. The TEM and AFM investigation of the resultant P3HT/RGO composites shows that P3HT nanowires grow from RGO, and connect individual RGO monolayers. Raman spectroscopy confirms the interaction between P3HT and RGO, which allows the manipulation of the RGO electrical properties. Such a bottom‐up approach provides interesting graphene‐based composites for nanometer‐scale electronics.

     

Direct Correlation Between Electric and Structural Properties During Solidification of Poly(3‐hexylthiophene) Drop‐Cast Films

Structural and electrical properties of semicrystalline P3HT cast films onto Si/SiO₂ surface are studied during the solidification under applied electric field in lateral OFET geometry. During evaporation of the solvent, the formation of P3HT crystallites is monitored simultaneously by time‐resolved X‐ray diffraction and by source‐drain current measurements. The electrical current is reaching its maximum in two pronounced regimes already before complete solidification of the polymer as detected by X‐ray diffraction intensities. The monitored complex time dependence of current and X‐ray intensities reveals a highest conducting level for the gel‐like state.     

Poly(3‐hexylthiophene) aggregation at solvent–solvent interfaces

The aggregation behavior of P3HT is investigated at the interface of orthogonal solvents for P3HT. The changeable characteristics of P3HT aggregate dispersions, for example, extent of aggregation and intrachain order, are studied by varying (1) the interfacial area, (2) the poor solvent used to induce aggregation – dichloromethane (DCM), hexane (HEX), and acetonitrile (AcN) – and (3) the relative composition of the good solvent, chloroform (CF), and poor solvents. The results are compared to those observed using rapid injection of the solvent. Miscibility gap values (Δδ) provide a reasonable justification of the assembly behavior of P3HT in the solvent mixtures in terms of the kinetics of polymer aggregation and the kinetics of solvent mixing at the interface. Atomic force microscopy (AFM) is used to analyze the morphology of films processed from dispersions with disparate characteristics, but having the same solvent composition, for example, 70:30 CF:HEX or 60:40 CF:DCM. Based on the disparity of the kinetics and miscibility gap values, the prevalence of specific structural motifs in the films, for example, spheroids (globules) and fibers, is effectively rationalized in terms of the structural attributes of the aggregates in the liquid phase rather than the evaporation rate (boiling point) differences of the solvents in the mixture. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 999–1011     

Annealing effect on performance and morphology of photovoltaic devices based on poly(3‐hexylthiophene)‐b‐poly(ethylene oxide)

Novel block copolymers, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) (P3HT‐b‐PEO) were synthesized via Suzuki coupling reaction of P3HT and PEO homopolymers. The copolymers were characterized by NMR, gel permeation chromatography, differential scanning calorimeter, and UV–vis measurements. A series of devices based on the block copolymers with a fullerene derivative were evaluated after thermal or solvent annealing. The device using P3HT‐b‐PEO showed higher efficiency than using P3HT blend after thermal annealing. Phase‐separated structures in the thin films of block copolymer blends were investigated by atomic force microscopy to clarify the relationship between morphologies constructed by annealing and the device performance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A New Poly(2,7‐Dibenzosilole) Derivative in Polymer Solar Cells

A new soluble conjugated copolymer based on 2,7‐dibenzosilole and 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole units has been synthesized (PBSDTBT). Bulk heterojunction solar cell devices are fabricated using this material as the donor and [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) as the acceptor. The power conversion efficiency is 1.6% under AM1.5 illumination. This material also shows a good V_OC (0.97 V). The results are quite promising considering the relatively large bandgap (1.9 eV) of this polymer.

     

Voltammetric Determination of Mercury(II) at Poly(3‐hexylthiophene) Film Electrode. Effect of Halide Ions

The well‐known method for the determination of mercury(II), which is based on the anodic stripping voltammetry of mercury(II), has been adapted for applications at the thin film poly(3‐hexylthiophene) polymer electrode. Halide ions have been found to increase the sensitivity of the mercury response and shift it more positive potentials. This behavior is explained by formation of mercuric halide which can be easily deposited and stripped from the polymer electrode surface. The procedure was optimized for mercury determination. For 120 s accumulation time, detection limit of 5 ng mL^?1 mercury(II) has been observed. The relative standard deviation is 1.3% at 40 ng mL^?1 mercury(II). The performance of the polymer film studied in this work was evaluated in the presence of surfactants and some potential interfering metal ions such as cadmium, lead, copper and nickel.     

Photoluminescence Study on Charge Transfer Behavior of Poly(3‐hexylthiophene) and PCBM Blends

Charge transfer behavior of Poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl eser (PCBM) in solutions and in films were examined by photoluminescence (PL) spectroscopy. PL study in solutions indicated that separation distance between P3HT and PCBM affected charge transfer efficiency more seriously than the interface area issue between P3HT and PCBM. P3HT/PCBM film showed very effective photo‐induced charge transfer before post‐thermal annealing on the bi‐layer P3HT/PCBM film. Charge transfer efficiency was gradually diminished by the annealing‐induced phase separation between P3HT and PCBM as revealed by increasing PL emission intensity of P3HT.     

Exploring the synthesis and impact of end‐functional poly(3‐hexylthiophene)

In recent years, end‐functional poly(3‐hexylthiophene) (P3HT) has proven to be instrumental in the continued development and innovation within the broad conjugated polymer arena, enabling a variety of applications, particularly in organic electronics. The availability of P3HT with controlled molecular weights, low polydispersity, and importantly, a wide range of reactive end‐groups not only serves as a key building block for the preparation of conjugated block copolymers but also facilitates the development of hybrid nanocomposite materials via inorganic surface modification strategies. This Highlight focuses on the synthetic approaches to end‐functional P3HT and the impact of these systems in emerging technologies. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 831–841     

High‐resolution MALDI‐TOF MS study on analysis of low‐molecular‐weight products from photo‐oxidation of poly(3‐hexylthiophene)

High‐resolution matrix‐assisted laser desorption/ionization (MALDI) time‐of‐flight mass spectrometry (TOF MS) was used for the analysis of the low‐molecular‐weight products from the photo‐oxidation of poly(3‐hexylthiophene) (P3HT) in solution and thin film. Eight new peak series were observed in the low‐mass range of the mass spectra of the products degraded in solution, and the formulas of the eight components were determined from the accurate mass. From SEC/MALDI‐TOF MS, two components were identified as the degraded products, and the other six components were derived from the fragmentation of the degraded products during the MALDI process. A mechanism for the formation of these components was proposed on the basis of the results of MALDI‐TOF MS. For the thin film degradation, a part of products in the solution degradation were observed, which supports that the oxidation of P3HT in solution and thin film proceeded in the same mechanism. This study shows that high‐resolution MALDI‐TOF MS is effective for the analysis of the low‐molecular‐weight products from P3HT photo‐oxidation and expected to be feasible for the degradation analyses of other polymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Solubility characteristics of poly(3‐hexylthiophene)

Solubility data for poly(3‐hexylthiophene) (P3HT) in 29 pure solvents are presented and discussed in detail. Functional solubility parameter (FSP) and convex solubility parameter (CSP) computations are performed and the CSP and FSP results are compared to previously reported Hansen solubility parameters (HSPs) and to the parameters calculated using additive functional group contribution methods. The empirical data reveals experimental solubility parameters with substantial polar (δ_P) and hydrogen‐bonding (δ_H) components, which are not intrinsic to the structure of the P3HT polymer. Despite these apparent irregularities, it is shown that the predictor method based on the solubility function, f, does provide a reliable way to quantitatively evaluate the solubility of P3HT in other solvents in terms of a given set of empirical solubility data. The solubility behavior is further investigated using linear solvation energy relationship (LSER) modeling and COSMO‐RS computations of the activity coefficients of P3HT. The LSER model reveals that (1) the cavity term, δ_T, is the dominant factor governing the solubility behavior of P3HT and (2) the solvent characteristics that dictate the structural order (crystallinity) of P3HT aggregates do not similarly influence the overall solubility behavior of the polymer. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1075–1087     

Intramolecular CH/π interactions in alkylaromatics: Monomer conformations for poly(3‐alkylthiophene) atomistic models

In existing poly(3‐alkylthiophenes) atomistic models, an extended conformation of the side chain is usually assumed. We report a first principle study of the side‐chain energetics of 3‐hexylthiophene, with the constraint of compatibility with crystal packing requirements. The first two torsion angles of the side chain closest to the ring were considered. Electron correlation is shown to be of great relevance in the assessment of the relative stability of folded conformers against extended ones. The roles of local charge‐transfer, rehybridization, steric repulsion, and basis set superposition error, were all considered in the rationalization of our results. We extend our analysis to the thiophene/methane complex in order to elucidate the main differences between intermolecular and intramolecular CH/π phenomena. While in the noncovalent complex a single C—H bond mediates the interaction, folded arrangements of 3‐alkylthiophenes require the collective effort of several aliphatic bonds. © 2013 Wiley Periodicals, Inc.     

Stille Catalyst‐Transfer Polycondensation Using Pd‐PEPPSI‐IPr for High‐Molecular‐Weight Regioregular Poly(3‐hexylthiophene)

A commercially available palladium N‐heterocyclic carbene (Pd‐NHC) precatalyst is used to initiate chain‐growth polymerization of 2‐bromo‐3‐hexyl‐5‐trimethylstannylthiophene. The molecular weight of the resultant poly(3‐hexylthiophene) can be modulated (7 to 73 kDa, Đ = 1.14 to 1.53) by varying the catalyst concentration. Mass spectrometry data confirm control over the polymer end groups and ¹H NMR spectroscopy reveals that the palladium catalyst is capable of “ring‐walking”. A linear relationship between M_n and monomer conversion is observed. Atomic force microscopy and X‐ray scattering verify the regioregular nature of the resultant polythiophene.

     

Random poly(3‐hexylthiophene‐co‐3‐cyanothiophene‐co‐3‐(2‐ethylhexyl)thiophene) copolymers with high open‐circuit voltage in polymer solar cells

For the purpose of developing poly(3‐hexylthiophene) (P3HT) based copolymers with deep‐lying highest occupied molecular orbital (HOMO) levels for polymer solar cells with high open‐circuit voltage (V_oc), we report a combined approach of random incorporation of 3‐cyanothiophene (CNT) and 3‐(2‐ethylhexyl)thiophene (EHT) units into the P3HT backbone. This strategy is designed to overcome CNT content limitations in recently reported P3HT‐CNT copolymers, where incorporation of more than 15% of CNT into the polymer backbone leads to impaired polymer solubility and raises the HOMO level. This new approach allows incorporation of a larger CNT content, reaching even lower‐lying HOMO levels. Importantly, a very low HOMO level of ?5.78 eV was obtained, representing one of the lowest HOMO values for exclusively thiophene‐based polymers. Lower HOMO levels result in higher V_oc and higher power conversion efficiencies (PCE) compared to the previously reported P3HT‐CNT copolymers containing only 3‐hexylthiophene and CNT units. As a result, solar cells based on P3HT‐CNT‐EHT(15:15) , which contains 70% of P3HT, 15% of CNT and 15% of EHT, yield a V_oc of 0.83 V in blends with PC₆₁BM while preserving high fill factor (FF) and high short‐circuit current density (J_sc), resulting in 3.6% PCE. Additionally, we explored the effect of polymer number‐average molecular weight (M_n) on the optoelectronic properties and solar cell performance for the example of P3HT‐CNT‐EHT(15:15). The organic photovoltaic (OPV) performance improves with polymer M_n increasing from 3.4 to 6.7 to 9.6 kDa and then it declines as M_n further increases to 9.9 and to 16.2 kDa. The molecular weight study highlights the importance of not only the solar cell optimization, but also the significance of individual polymer properties optimization, in order to fully explore the potential of any given polymer in OPVs. The broader ramification of this study lies in potential application of these high band gap copolymers with low‐lying HOMO level in the development of ternary blend photovoltaics as well as tandem OPV. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1526–1536     

Synthesis and morphology of all‐conjugated donor–acceptor block copolymers based on poly(3‐hexylthiophene) and poly(naphthalene diimide)

A series of all‐conjugated diblock and triblock copolymers comprised of poly(naphthalene diimide) (PNDI)‐based n‐type and the poly(3‐hexylthiophene) (P3HT) segments could be synthesized via the Kumada catalyst‐transfer polycondensation process. The crystalline structures and chain orientation of the block copolymer thin films were systematically studied by grazing incident wide‐angle X‐ray scattering (GIWAXS). The GIWAXS results indicated that both the P3HT and PNDI segments in the block copolymers form exclusive crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domain aligns with a face‐on rich orientation. In contrast, the blend films of the P3HT and PNDI homopolymers also show two distinguished crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domains align in different ways depending on the chemical structure of n‐type polymers, that is, PNDI1Th is isotropically dispersed, while PNDI2Th aligns with a face‐on rich orientation. In addition, the effect of thermal annealing on the crystalline behavior of the block copolymers is reported. The GIWAXS results indicated that thermal annealing increases the crystallinity of both segments without affecting their chain orientation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1139–1148     

Thermodynamic features of perfectly crystalline poly(3‐hexylthiophene) based on Flory's relation

Poly(3‐hexylthiophene) (P3HT) as a conjugated polymer has many electrical and photovoltaic applications. However, reliable values for the equilibrium melting temperature ( ${T°}_m$) and for the enthalpy of fusion of a perfect P3HT crystal ( ${\Delta H°}_m$) are still in doubt. In the published works, ${\Delta H°}_m$ ranges from 33 to 99 J/g. Here, the melting point of P3HT in P3HT‐diluent mixtures is measured with changing the diluent concentration. By satisfying the requirements of Flory relation, “working with the same polymer crystals” and “working in the equilibrium state,” usually neglected in the literature, a reliable value of ${\Delta H°}_m$ = 83 ± 2 J/g is obtained. The reported values for ${T°}_m$ of P3HT are also in a wide range, 260?300 °C. In this work, accurate applying of the Hoffman‐Weeks relation, against the effects of lamellar thickening, yields ${T°}_m$ = 272 ± 2 °C rather than 300 ± 2°C reported in the literature. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 431–437