A strategy for the high dispersion of PtRu nanoparticles onto carbon nanotubes and their electrocatalytic oxidation of methanol

Carbon nanotubes (CNTs) were non-covalently functionalized by 1-pyrenecarboxaldehyde (PCA) via π-π stacking interactions. PCA not only acts as the reductant for the deposition of PtRu nanoparticles, but the oxidation product of PCA can also effectively anchor and stabilize the in-situ-produced PtRu?NPs on the surface of CNTs. Transmission electron microscopy demonstrates that PtRu?NPs are uniformly dispersed on the surface of CNTs with small particles sizes of about 1.7 nm. The obtained PtRu-NP/CNT composites have higher electrochemical surface areas, electrocatalytic activities, and better stability towards methanol oxidation compared to PtRu?NPs supported on pristine CNTs.     

Sensitive Electrochemical Prostate Specific Antigen Aptasensor: Effect of Carboxylic Acid Functionalized Carbon Nanotube and Glutaraldehyde Linker

The performance of carboxylic acid functionalized carbon nanotubes (CNTs_(COOH)), chitosan (Chit), carbon nanotubes‐chitosan (CNTs‐Chit and CNTs_(COOH)‐Chit) for immobilizing of amino‐functionalized ssDNA and fabrication of electrochemical prostate specific antigen (PSA) aptasensor were studied in detail using X‐ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT‐IR) and electrochemical impedance spectroscopy (EIS). The assemblies of capture probe are formed on the surface via two approaches: EDC/NHS chemistry and glutaraldehyde linker. Cyclic voltammetry (CV), differential pulse voltammetry (DPV) and EIS techniques were used to investigate the analytical performance of the PSA aptasensor. Under optimum conditions the sensitivity of 0.0026 µA/(ng/ml) and a limit of detection of 0.75 ng/ml (22 pM) were obtained for PSA detection. This protocol offers a new means for sensitive detection of PSA with some advantages in terms of simplicity, selectivity, ease of use and regenerability.     

Functionalization of Carbon Nanotubes by an Ionic‐Liquid Polymer: Dispersion of Pt and PtRu Nanoparticles on Carbon Nanotubes and Their Electrocatalytic Oxidation of Methanol

Small beginnings : Metal nanoparticle/CNT nanohybrids are synthesized from carbon nanotubes (CNTs) functionalized with an ionic‐liquid polymer. The Pt and PtRu nanoparticles with narrow size distribution (average diameter: (1.3±0.4) nm for PtRu, (1.9±0.5) nm for Pt) are dispersed uniformly on the CNTs (see images) and show good performance in methanol electrooxidation.

     

Three-dimensional nanostructured carbon nanotube array/PtRu nanoparticle electrodes for micro-fuel cells

We have fabricated three-dimensional (3D) nanostructured carbon nanotube (CNT) array/PtRu nanoparticle (with the average molar percentage (26%) of Ru) electrodes using anodic aluminum oxide (AAO) templates for micro-fuel cells. 3D nanostructured CNT array was used to support PtRu nanoparticles to enhance the utilization efficiency of Pt. The 3D nanostructured CNT array/PtRu electrodes show the excellent catalytic activity and electrochemical stability of electro-oxidation of methanol. Their anodic current density is 10 times as high as that of PtRu thin-films, which could be explained in terms of the high specific surface area of 3D nanostructured CNT array supporting films and the uniform distribution of PtRu nanoparticles.     

A novel synthesis of polymer brush on multiwall carbon nanotubes bearing terminal monomeric unit

A novel approach to fabricate polymer brushes on the surface of carbon nanotubes (CNTs) is proposed. Carboxyl groups on the surface of chemically oxidized CNTs were reacted with hexamethylene diisocyanate, followed by a reaction with methacrylamide to give terminal vinyl groups‐functionalized CNTs, so called “CNT‐mer.” The synthetic procedure was investigated step‐by‐step and the synthesized CNT‐mer was used to grow polystyrene (PS) from CNTs by a simple in situ polymerization in the presence of a thermal initiator. By employing ¹H NMR, X‐ray photoelectron spectroscopy, thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, and light scattering, the experimental results were verified. Using this approach, 45% PS with respect to CNTs are grafted on the surface of CNTs with about 4.0 nm thickness. This novel technique would provide a facile route to prepare tailor‐made polymer brushes on the surface of CNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44:6394–6401, 2006     

Buchwald‐Hartwig amination reaction of aryl halides using heterogeneous catalyst based on Pd nanoparticles decorated on chitosan functionalized graphene oxide

In this work, graphene oxide was functionalized with chitosan (GO‐Chit) followed by a simple approach for immobilization of palladium nanoparticles onto a chitosan grafted graphene oxide surface. The Pd‐nanocomposite (GO‐Chit‐Pd) was characterized using Transmission Electron Microscopy (TEM), Fourier transforms infrared spectroscopy (FT‐IR), and X‐ray diffraction (XRD) measurements. The catalytic activity of the prepared heterogeneous graphene oxide functionalized chitosan‐palladium (GO‐Chit‐Pd) was investigated in term of C‐N coupling reaction (Buchwald‐Hartwig amination reaction of aryl halides) yielding products of N‐arylamines. The easy purification, convenient operation, and environmental friendliness, combined with a high yield, render this method viable for use in both laboratory research and larger industrial scales. Studying the reusability of the catalyst in this work showed that it could be reused for five times without obvious loss in catalytic activity.     

Isoprene Polymerization on Iron Nanoparticles Confined in Carbon Nanotubes

The confinement of air‐protected metallic magnetic nanoparticles in the inner cavity of carbon nanotubes (CNTs) should offer an interesting perspective for biomedical applications or for controlling CNT alignment in composites. Because the direct confinement of polymer‐precoated nanoparticles in CNTs could be restricted by diffusion limitations, we developed a process based on: 1) the confinement of iron nanoparticles surface‐modified with an iron polymerization catalyst in the cavity of CNTs and 2) the polymerization of isoprene on the confined nanoparticles. The resulting material consists in CNT‐confined iron nanoparticles coated with a polyisoprene air barrier. This approach constitutes a proof of concept for the development of smart materials for use in medicine or composites.     

Morphology,rheological and crystallization behavior in non-covalently functionalized carbon nanotube reinforced poly(butylene succinate) nanocomposites with low percolation threshold

Multi-walled carbon nanotubes (CNTs) were non-covalently functionalized by surface wrapping of poly(sodium 4-styrenesulfonate) (PSS) with the aid of ultrasound. The functionalized CNTs were incorporated into poly(butylene succinate) (PBS) through solution coagulation to fabricate CNTs filled PBS nanocomposites. The morphologies of the PBS/CNT nanocomposites were studied by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the effect of loading of functionalized CNT on the rheological behavior, electrical conductivity and mechanical properties of the nanocomposites was investigated systemically. SEM observation indicates that functionalized CNTs dispersed in PBS matrix without obvious aggregation and showed good interfacial adhesion with the PBS phase. TEM observation reveals that a CNT network was formed when the loading of CNTs increased from 0.1 to 0.3 wt%. Rheological investigation indicates the formation of a CNT network with a percolation threshold of only 0.3 wt%. Significant improvement in electrical conductivity occurred at CNT loading of 0.3 wt%, with the value of electrical conductivity increasing by six orders of magnitude compared to neat PBS. Differential scanning calorimetry indicates that the melt crystallization temperature of PBS was improved by ∼14 °C with addition of only 0.05 wt% functionalized CNTs. Tensile tests indicate that both the yield strength and Young's modulus of PBS were apparently reinforced by incorporation of functionalized CNTs, while the elongation at break was reduced gradually.     

Development of stable PtRu catalyst coated with manganese dioxide for electrocatalytic oxidation of methanol

Manganese dioxide was coated on multiwall carbon nanotubes-supported PtRu particles to prepare the MnO₂/PtRu/CNT catalyst by a facile oxidation–reduction method. The prepared catalyst showed a high stability for electrocatalytic oxidation of methanol. After 2000 potential cycles, 55% activity still remained for MnO₂/PtRu/CNT catalyst, while only 30% activity remained for PtRu/CNT, which indicated that the electrochemical stability of MnO₂/PtRu/CNTs was improved significantly. MnO₂ in MnO₂/PtRu/CNTs prevented the dissolution of PtRu particles as well as the corrosion of the CNT supports, resulting in the improvement of the stability and activity.     

Electrospinning of poly(trimethylene terephthalate)/carbon nanotube composites

Poly(trimethylene terephthalate) (PTT) nanocomposites containing carbon nanotubes (CNTs) with different surface structure and aspect ratio were prepared by melt compounding for electrospinning. The dispersion state of the CNTs in the composites was then examined utilizing rheology tools. The results show that carboxylic surface functionalized CNTs present better dispersion in the matrix than hydroxy surface functionalized CNTs because the former has stronger affinity to the PTT. Besides surface functionalization, the aspect ratio of CNTs is also vital to their final dispersion. The CNTs with lower aspect ratio are dispersed as individuals or small bundles while those with higher aspect ratio are dispersed mainly as flocs with large hydrodynamic radius, showing higher effective volume fraction. The presence of CNTs has a large influence on the morphologies of electrospun fiber and on the appearances of CNTs in the fibers. In the presence of CNTs with lower aspect ratio, continuous composite fibers are obtained. But the structure of those continuous fibers highly depends on the surface group of CNTs. Carboxylic surface functionalized CNTs are well embedded by the PTT and oriented along the fiber axis during electrospinning, leading to bead-free and uniform fiber morphology; while hydroxy surface functionalized CNTs show tortuous conformations with less orientation in the fibers, and as a result, the obtained fibers show beaded and misshaped morphologies. In the case of higher aspect ratio, however, the CNTs prefer to exist as entanglements or knots in the streamlines, and thereby only beaded or even uncontinuous fibers are obtained. Therefore, the formation and fiber morphology of PTT/CNT composite fibers obtained by electrospinning strongly depend on the surface functional groups of the CNTs, as well as on the CNT structure.     

Marrying mussel inspired chemistry with SET‐LRP: A novel strategy for surface functionalization of carbon nanotubes

Surface functionalization of carbon nanotubes (CNTs) with a thermo responsive polymer was achieved via combination of mussel inspired chemistry and surface initiated single electron transfer living radical polymerization (SET‐LRP). In this procedure, CNTs were first coated with polydopamine (PDA) through self polymerization under a rather mild condition. And then PDA functionalized CNTs bearing with amino and hydroxyl groups were further reacted with bromo isobutyryl bromide. Finally, a thermo responsive polymer poly(N‐isopropylacrylamide) (PNIPAM) was introduced on the CNTs via SET‐LRP. The successful surface modification of CNT‐PDA‐PNIPAM was evidenced by a series of characterization techniques. The resulting CNT‐PDA‐PNIPAM showed significant enhancement of dispersibility in both aqueous and organic solvents. More importantly, these CNT‐polymer nanocomposites showed obvious thermo responsive behavior due to the surface coating CNTs with PNIPAM. As compared with previous methods, this method is not required oxidation of CNTs to introduce funcitonal groups for immobilization of the polymerization initiators. More importantly, this method could also be utilized for fabricating many other polymer nanocomposites because of the strong and universal adhesive of PDA to various materials. It is therefore, the novel strategy via marrying mussel inspired chemistry with SET‐LRP should be a simple, general and effective method for surface functionalization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1872–1879     

PtRu catalysts supported on heteropolyacid and chitosan functionalized carbon nanotubes for methanol oxidation reaction of fuel cells

A simple self-assembly approach has been developed to functionalize carbon nanotubes (CNTs) with chitosan (CS) and heteropolyacids (HPAs) of phosphomolybdic acid (H(3)PMo(12)O(40), HPMo) and phosphotungstic acid (H(3)PW(12)O(40), HPW). The non-covalent functionalization method, which introduces homogenous surface functional groups with no detrimental effect on graphene structures of CNTs, can be carried out at room temperature without the use of corrosive acids. The PtRu nanoparticles supported on HPAs-CS-CNTs have a uniform distribution and much smaller size as compared to those of the PtRu nanoparticles supported on conventional acid treated CNTs (PtRu/AO-CNTs). The onset and peak potentials for CO(ad) oxidation on PtRu/HPAs-CS-CNTs catalysts are more negative than those on PtRu/AO-CNTs, indicating that HPAs facilitate the electro-oxidation of CO. The PtRu/HPMo-CS-CNTs catalyst has a higher electrocatalytic activity for methanol oxidation and higher tolerance toward CO poisoning than PtRu/HPW-CS-CNTs. The better electrocatalytic enhancement of HPMo on the PtRu/HPAs-CS-CNTs catalyst is most likely related to the fact that molybdenum-containing HPAs such as HPMo have more labile terminal oxygen to provide additional active oxygen sites while accelerating the CO and methanol oxidation in a similar way to that of Ru in the PtRu binary alloy system.     

Functional groups modulate the sensitivity and electron transfer kinetics of neurochemicals at carbon nanotube modified microelectrodes

The surface properties of carbon-based electrodes are critically important for the detection of biomolecules and can modulate electrostatic interactions, adsorption and electrocatalysis. Carbon nanotube (CNT) modified electrodes have previously been shown to have increased oxidative sensitivity and reduced overpotential for catecholamine neurotransmitters, but the effect of surface functionalities on these properties has not been characterized. In this study, we modified carbon-fiber microelectrodes (CFMEs) with three differently functionalized single-wall carbon nanotubes and measured their response to serotonin, dopamine, and ascorbic acid using fast-scan cyclic voltammetry. Both carboxylic acid functionalized and amide functionalized CNTs increased the oxidative current of CFMEs by approximately 2-6 fold for the cationic neurotransmitters serotonin and dopamine, but octadecylamine functionalized CNTs resulted in no significant signal change. Similarly, electron transfer was faster for both amide and carboxylic acid functionalized CNT modified electrodes but slower for octadecylamine CNT modified electrodes. Oxidation of ascorbic acid was only increased with carboxylic acid functionalized CNTs although all CNT-modified electrodes showed a trend towards increased reversibility for ascorbic acid. Carboxylic acid-CNT modified disk electrodes were then tested for detection of serotonin in the ventral nerve cord of a Drosophila melanogaster larva, and the increase in sensitivity was maintained in biological tissue. The functional groups of CNTs therefore modulate the electrochemical properties, and the increase in sensitivity from CNT modification facilitates measurements in biological samples.     

Preparation of airborne Ag/CNT hybrid nanoparticles using an aerosol process and their application to antimicrobial air filtration

Carbon nanotubes (CNTs) have been widely used in a variety of applications because of their unique structure and excellent mechanical and electrical properties. Additionally, silver (Ag) nanoparticles exhibit broad-spectrum biocidal activity toward many different bacteria, fungi, and viruses. In this study, we prepared Ag-coated CNT hybrid nanoparticles (Ag/CNTs) using aerosol nebulization and thermal evaporation/condensation processes and tested their usefulness for antimicrobial air filtration. Droplets were generated from a CNT suspension using a six-jet collison nebulizer, passed through a diffusion dryer to remove moisture, and entered a thermal tube furnace where silver nanoparticles were generated by thermal evaporation/condensation at ～980 °C in a nitrogen atmosphere. The CNT and Ag nanoparticle aerosols mixed together and attached to each other, forming Ag/CNTs. For physicochemical characterization, the Ag/CNTs were introduced into a scanning mobility particle sizer (SMPS) for size distribution measurements and were sampled by the nanoparticle sampler for morphological and elemental analyses. For antimicrobial air filtration applications, the airborne Ag/CNT particles generated were deposited continuously onto an air filter medium. Physical characteristics (fiber morphology, pressure drop, and filtration efficiency) and biological characteristics (antimicrobial tests against Staphylococcus epidermidis and Escherichia coli bioaerosols) were evaluated. Real-time SMPS and transmission electron microscopy (TEM) data showed that Ag nanoparticles that were <20 nm in diameter were homogeneously dispersed and adhered strongly to the CNT surfaces. Because of the attachment of Ag nanoparticles onto the CNT surfaces, the total particle surface area concentration measured by a nanoparticle surface area monitor (NSAM) was lower than the summation of each Ag nanoparticle and CNT generated. When Ag/CNTs were deposited on the surface of an air filter medium, the antimicrobial activity against test bacterial bioaerosols was enhanced, compared with the deposition of CNTs or Ag nanoparticles alone, whereas the filter pressure drop and bioaerosol filtration efficiency were similar to those of CNT deposition only. At a residence time of 2 h, the relative microbial viabilities of gram-positive S. epidermidis were ～32, 13, 5, and 0.9% on the control, CNT-, Ag nanoparticle-, and Ag/CNT-deposited filters, respectively, and those of gram-negative E. coli were 13, 2.1, 0.4, and 0.1% on the control, CNTs, Ag nanoparticles, and Ag/CNTs, respectively. These Ag/CNT hybrid nanoparticles may be useful for applications in biomedical devices and antibacterial control systems.     

Kinetics studies on the accelerated curing of liquid crystalline epoxy resin/multiwalled carbon nanotube nanocomposites

A new class of nanocomposite has been fabricated from liquid crystalline (LC) epoxy resin of 4,4′‐bis(2,3‐epoxypropoxy) biphenyl (BP), 4,4′‐diamino‐diphenyl sulfone (DDS), and multiwalled carbon nanotubes (CNTs). The surface of the CNTs was functionalized by LC epoxy resin (ef‐CNT). The ef‐CNT can be blended well with the BP that is further cured with an equivalent of DDS to form nanocomposite. We have studied the curing kinetics of this nanocomposite using isothermal and nonisothermal differential scanning calorimetry (DSC). The dependence of the conversion on time can fit into the autocatalytic model before the vitrification, and then it becomes diffusion control process. The reaction rate increases and the activation energy decreases with increasing concentration of the ef‐CNT. At 10 wt % of ef‐CNT, the activation energy of nanocomposite curing is lowered by about 20% when compared with the neat BP/DDS resin. If the ef‐CNT was replaced by thermal‐insulating TiO₂ nanorods on the same weight basis, the decrease of activation energy was not observed. The result indicates the accelerating effect on the nanocomposite was raised from the high‐thermal conductivity of CNT and aligned LC epoxy resin. However, at ef‐CNT concentration higher than 2 wt %, the accelerating effect of ef‐CNTs also antedates the vitrification and turns the reaction to diffusion control driven. As the molecular motions are limited, the degree of cure is lowered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Photoinduced Formation and Characterization of Electron–Hole Pairs in Azaxanthylium‐Derivatized Short Single‐Walled Carbon Nanotubes

2‐Azaxanthone, a nitrogenated derivative of the well‐studied organic chromophore xanthone, has been covalently bound through 2‐(ethylthio)ethylamido linkers to the carboxylic acid groups of short, soluble single‐walled carbon nanotubes (CNTs) of 450 nm average length, and the resulting azaxanthylium‐functionalized CNTs (AZX‐CNT, 8.5 wt % AZX content) characterized by solution ¹H NMR, Raman and IR spectroscopy and thermogravimetric analysis. Comparison of the quenching of the triplet excited state of AZX (steady‐state and time‐resolved) and of the transient optical spectra of CNTs and AZX‐CNT shows that the covalent linkage boosts the interaction between the azaxanthylium moiety and the short CNT units. The triplet excited state of the azaxanthylium derivative is quenched by CNT with and without covalent bonding, but when it is covalently bonded, the singular transient spectrum is compatible with the photogeneration of electron holes through electron transfer from CNT to excited azaxanthylium units.     

Tuning of redox properties of iron and iron oxides via encapsulation within carbon nanotubes

We report the tuning of the redox properties of iron and iron oxide nanoparticles by encapsulation within carbon nanotubes (CNTs) with varying inner diameters. Raman spectroscopy was employed to investigate the interaction of the encapsulated nanoparticles with the CNTs. A red shift of the Fe-O mode is observed in the nanoparticles deposited on the outer CNT surfaces with respect to bulk Fe2O3. However, this mode is found to be stepwise blue-shifted with decreasing inner diameter in the CNT-encapsulated Fe2O3 nanoparticles, suggesting an enhanced interaction of Fe2O3 with the inner CNT surface as its curvature increases. The autoreduction of the encapsulated Fe2O3 is significantly facilitated inside CNTs with respect to the outside nanoparticles. Interestingly, it becomes more facile with decreasing CNT channel diameter as evidenced by temperature programmed reaction, in situ XRD, and Raman spectroscopy. The oxidation of encapsulated metallic Fe nanoparticles on the other hand is retarded in comparison to that of the outside Fe particles as shown by in situ XRD and gravimetrical measurements with an online microbalance. We attribute this tunable redox behavior of transition metal nanoparticles inside CNTs to a particular electronic interaction of the encapsulates with the interior CNT surface, which stabilizes the metallic state of Fe.     

Enhanced Nucleation and Crystallization in PLA/CNT Composites via Disperse Orange 3 with Corresponding Improvement in Nanomechanical Properties

The potential for the material property improvement through the addition of carbon nanotubes (CNTs) in composite materials is often limited due to CNT agglomeration. In this work, Disperse Orange 3 (DO3) was investigated to determine its effectiveness in dispersing CNTs in a poly (lactic acid) (PLA) matrix. First, adsorption studies of DO3 onto CNTs were performed to determine the appropriate amount of DO3 to add so that the CNT surface will be nearly saturated with DO3 while limiting the excess DO3 dissolved in the polymer. The resultant improvements in the mechanical properties were determined via nanoindentation. Highly stable dispersion of CNTs in tetrahydrofuran with DO3 was observed 72 hours after sonication. Scanning electron microscopy confirmed that DO3‐functionalized CNTs were able to separate and disperse well inside of the PLA matrix. Addition of DO3 to the nanocomposite resulted in an increase in the glass transition temperature and crystallinity of the composite due to the more effective dispersion of the nanofiller which serves as a nucleation agent. The CNTs treated with DO3 also increased the elastic modulus and hardness of the composite compared to neat PLA and untreated PLA‐CNT composites. From this study, DO3 was demonstrated to be an effective dispersing agent in the solvent and the PLA matrix which allowed for enhanced crystallization and improved nanomechanical properties in the resultant composite.     

Sonochemical oxidation of multiwalled carbon nanotubes

Functionalization of carbon nanotubes (CNTs) is important for enhancing deposition of metal nanoparticles in the fabrication of supported catalysts. A facile approach for oxidizing CNTs is presented using a sonochemical method to promote the density of surface functional groups. This was successfully employed in a previous study [J. Phys. Chem. B 2004, 108, 19255] to prepare highly dispersed, high-loading Pt nanoparticles on CNTs as fuel cell catalysts. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy, cyclic voltammetry, and settling speeds were used to characterize the degree of surface functionalization and coverage. The sonochemical method effectively functionalized the CNTs. A mixture of -C-O-/-C=O and -COO- was observed along with evidence for weakly bound CO at longer treatment times. The integrated XPS C 1s core level peak area ratios of the oxidized-to-graphitic C oxidation states, as well as the atom % oxygen from the O 1s level, showed an increase in peak intensity (attributed to -CO(x)()) with increased sonication times from 1 to 8 h; the increase in C surface oxidation correlated well with the measured atom %. Most of the CNT surface oxidation occurred between 1 and 2 h. The sonochemically treated CNTs were also studied by cyclic voltammetry and settling experiments, and the results were consistent with the XPS observations.     

Site-specific assembly of DNA and appended cargo on arrayed carbon nanotubes

We describe a strategy that permits discrete regions of arrayed carbon nanotubes (CNTs) to be functionalized simultaneously and specifically with DNA oligonucleotides. The different chemical properties of two regions on single CNTs and orthogonal chemical coupling strategies have been exploited to derivatize CNTs within highly ordered arrays with multiple DNA sequences. Through duplex hybridization, we then targeted different DNA sequences with appended metal nanoparticles to distinct sites on the CNT architecture with precise spatial control. The materials generated from these studies represent the first CNTs with bipartite functionalization. The approach described provides a high level of precision in parallel and directed assembly of DNA sequences and appended cargo and is useful for the preparation of novel hybrid bionanomaterials.