铜锆中间合金中铜、锆含量的联合测定

研究了铜锆中间合金中铜、锆的测定方法。试样经高氯酸、硝酸分解后,采用电解法测定铜:分离铜后的电解液,经盐酸处理后以二甲酚橙为指示剂,用EDTA标准溶液滴定测定锆。该方法简便,具有良好的精密度和准确度,相对标准偏差分别为铜0.19％。锆0.15％。     

Polarographic determination of traces of zirconium in ores by use of complex-forming compounds adsorbable at the dropping mercury electrode

A polarographic method is proposed for the determination of trace zirconium down to the 5 x 10(-9)M level, based on the adsorption of the complex of zirconium with oxalic acid + cupferron + diphenylguanidine at the dropping mercury electrode in sodium acetate-acetic acid solution (pH 5.7). Under optimum conditions the wave-height is proportional to the concentration of zirconium in the range from 0 to 0.4 mug ml . The serious interference from titanium(IV) can be effectively eliminated by solvent extraction with 3% tri-n-octylamine from lN sulphuric acid and stripping with 0.1 M perchloric acid-lM hydrochloric acid-2M nitric acid mixture. The mechanism giving rise to the wave for the zirconium complex has been investigated. The method has been applied to the determination of trace zirconium in ores and ceramics.     

Complexometric determination of aluminium in iron ore,sinter, concentrates and agglomerates

A method for the complexometric determination of aluminium in iron ore, sinter, concentrates and agglomerates encountered in international trade is described. The sample is fused in a zirconium crucible with a mixed flux of sodium carbonate and sodium peroxide. The fused mass is completely soluble in hydrochloric acid. The R₂O₃ oxides are then precipitated with ammonia and redissolved in hydrochloric acid. Elements such as iron, titanium and zirconium are separated from aluminium by solvent extraction with cupferron and chloroform. After removal of traces of organic matter from the aqueous phase, the solution is treated with an excess of EDTA, which is then back-titrated with zinc solution (Xylenol Orange as indicator). Addition of ammonium fluoride then releases EDTA equivalent to the aluminium and this is titrated with zinc solution. The method is rapid. The precision and accuracy are excellent, and the results comparable with those obtained by the referee method.     

The determination of zirconium in fluoride-containing solutions

In the recommended procedure the zirconium is first precipitated from solution as the insoluble barium fluozirconate. After separation, the precipitate is dissolved in a mixture of nitric and boric acids and the zirconium is then precipitated as its hydroxide. This precipitate is separated, dissolved in hydrochloric acid and this solution is evaporated to fumes of perchloric acid to remove completely fluoride ions. The zirconium content is then determined volumetrically by adding a slight excess of a standard solution of ethylenediaminetetra-acetic acid and back titrating with a standard iron solution at pH 2.3 using potassium benzohydroxamate as indicator and the photometric technique for end-point detection. This method is applicable to the determination of milligram amounts of zirconium in fluoride-containing nitric or hydrochloric acid solutions provided that the concentration of these acids is below 3N. It is also suitable for the determination of zirconium in the presence of any of the following elements - uranium, titanium, niobium, tantalum, molybdenum, tungsten, lead, iron, copper and tin.     

EDTA滴定法测定除尘灰中锌含量

采用灰化后再溶解试样的方法,成功解决了除尘灰因碳含量过高而难于溶解的问题;将灰化后的试样以HCl-HNO3-HF-HClO4混酸溶解,在氯酸钾存在下,以铁盐作载体,用氨水沉淀分离大部分铁、铝、铅等元素,以硫脲-氟化物、硫代硫酸钠、抗坏血酸作掩蔽剂,掩蔽剩余少量铜、锡、铁等干扰元素,在pH=5.5~6条件下,以二甲酚橙为指示剂,用EDTA标准溶液滴定得到锌的含量。方法的相对标准偏差在0.75%~2.8%,加标回收率在98.0%~102%。方法操作简便,且分析结果准确度、重现性较好,可以满足生产检验的需要。     

A rapid procedure for the simultaneous determination of zirconium and hafnium in high-temperature alloys by means of a spectrophotometric masking approach

Data are presented for a refined spectrophotometric procedure for the simultaneous determination of zirconium and hafnium based on the combined effects of hydrogen peroxide, sodium sulphate, and excess of zirconium ion on the hafnium and zirconium complexes with Xylenol Orange in 0.2M perchloric acid. Isolation procedures for the hafnium/zirconium content of complex high-temperature alloys which result in an ionic substrate compatible with the spectrophotometric masking method were devised.     

The assay of sodium citrate and sodium potassium tartrate by cation exchange and non-aqueous titrimetry

Sodium citrate and sodium potassium tartrate are assayed by passing aqueous solutions of the salts through cation exchange resin columns, concentrating the effluents from the columns, and then titrating the effluents with standard sodium hydroxide solution. Sodium citrate is assayed by titrating a solution of the salt in glacial acetic acid with standard acetous perchloric acid, the end-point being detected potentiometrically; sodium potassium tartrate is assayed by stirring the salt in excess standard acetous perchloric acid, and then backtitrating the excess acetous perchloric acid with standard acetous potassium acetate, the end-point being detected potentiometrically.     

Analysis of tellurides of lead and tin by automatic titrations

An analytical method based on automatic potentiometric EDTA and redox titrations was developed for the analysis of tellurides of lead and tin.First, the sum of lead and tin is titrated at pH 4.5 by adding a known excess of EDTA and back-titrating with a standard lead solution. After addition of ammonium fluoride to mask the tin, the EDTA released from the Sn-EDTA complex is titrated with standard lead solution. Alternatively, after the determination of total lead and tin, lead may be determined by back-titration with standard lead on a separate sample aliquot using tartaric acid to mask the tin. Tellurium is separated as tellurous acid, which is then dissolved in a dilute sulfuric acid solution and oxidized by permanganate at room temperature; the excess permanganate is back-titrated with iron(II) solution automatically. This titration may also be used to determine tellurium in the presence of lead and tin after treatment with perchloric acid. Accuracies of 0.1-0.2% can be obtained.     

Determination of phosphorus in fertilizers by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) method was developed for the determination of phosphorus in fertilizers. Total phosphorus, direct extraction available phosphorus (EDTA), and water-soluble phosphorus, reported as phosphorus pentoxide (P205), in 15 Magruder check fertilizers were measured by ICP-AES, and the results were compared with those obtained by the AOAC official method. Five analytical wavelengths of phosphorus, 177.499, 178.287, 213.618, 214.914, and 253.565 nm, were tested for the determination of phosphorus in fertilizers, and their detection limits were obtained. Acid effects of perchloric acid and possible matrix effects of aluminum, calcium, magnesium, potassium, and sodium were negligible for phosphorus determination. Wavelength 213.618 nm was the best analytical wavelength for phosphorus determination by all 3 sample preparation methods for the selected Magruder fertilizers. The results demonstrated that the accuracy and precision of the ICP-AES method were comparable with those of the official methods.     

EDTA容量法快速测定酸法生产金属镓的液体物料中镓含量

建立了在酸法生产金属镓过程中,用NH4F掩蔽溶液中的铝,加入过量的EDTA标准溶液使之与镓元素完全络合,调整条件试剂硼酸溶液和无水乙醇的加入量,保证终点的准确判断,过量EDTA以PAN为指示剂用硫酸铜标准溶液回滴求得液体物料中镓含量的分析方法.实验表明,方法的相对标准偏差(RSD)为2.8％～6.5％,加标回收率为97.14％～104.0％.方法有较高的准确性和可靠性,且测定结果精密度高,可实现酸法生产金属镓液体物料中镓含量的快速检测.     

Determination of zirconium in zirconium metal and zirconium powder by use of mandelic acid

An accurate gravimetric method is proposed for the determination of zirconium in zirconium metal and zirconium powder by use of mandelic acid. The sample is dissolved in a mixture of hydrofluoric, nitric, perchloric and sulfuric acids, the solution is evaporated to dryness, and the salts are dissolved in dilute hydrochloric acid. Zirconium mandelate is precipitated at 80°. The residual zirconium in the filtrate is recovered by heating at 80° overnight and the combined precipitates are ignited to Zirconium dioxide. An investigation was made of the factors involved in the dissolution of the sample, precipitation with mandelic acid, ignition of the precipitate, and size of sample. The effect of hafnium is discussed.     

Fluorimetric determination of zirconium with morin

Zirconium can be determination fluorimctrically with morin in 2M hydrochloric acid in the presence of such elements as Al, Be, Ga, Sb, Sn, Th and U, which fluorcsce much less strongly under the conditions, by measuring the fluorescence intensity before and after adding ethylenediaminetetraacetic acid. This substance destroys the fluorescence of zirconium only and the difference in fluorescence intensities corresponds to the concentration of zirconium in solution. The determination of zirconium in the presence of aluminum has especially been studied. Satisfactory accuracy can be obtained even when Al/Zr = 10,000, if the proper morin concentration is used. Iron docs not interfere if reduced to the ferrous state with mercap oacetic acid, Zirconium can be determined in silicate rocks without any separations except those made automatically in tlie sodium carbonate decomposition. Niobium and tantalum should not exceed 0.05%.     

硫酸铅分离-EDTA滴定法测定铜闪速冶炼烟尘中的铅

建立了用硫酸形成硫酸铅沉淀加以分离,再用EDTA络合滴定法测定铜闪速冶炼烟尘中铅量的方法。试样用盐酸、硝酸、硫酸、氟化氢铵和高氯酸溶解,用硫酸沉淀铅与其它干扰元素分离,沉淀溶解于乙酸-乙酸钠缓冲溶液中,以巯基乙酸掩蔽铋,抗坏血酸掩蔽铁,二甲酚橙作指示剂,用Na2EDTA标准滴定溶液滴定溶液中铅含量,采用火焰原子吸收光谱法测定滤液中铅含量加以补正。实验结果表明,沉淀时硫酸(1+24)加入量为50 mL,无水乙醇加入量为10 mL,乙酸-乙酸钠缓冲溶液加入量为30 mL。方法相对标准偏差(RSD)在0.35%~1.5%,加标回收率为在99.0%~101%。完全满足生产控制分析的要求,同时也可以作为类似物料中铅分析的参考方法。     

Electrochemical stripping determination of traces of copper, lead, cadmium and zinc in zirconium metal and zirconium dioxide

Procedures have been developed for the determination of copper, lead, cadmium and zinc in zirconium metal and zirconium dioxide, at concentrations of 1 ppm or less. Zirconium metal was dissolved in suphuric acid, and zirconium dioxide decomposed under pressure with hydrofluoric acid. Sample solutions were prepared in dilute sulphuric acid. For the stripping determination, the sample solution was either mixed with a complexing tartrate base electrolyte or the pre-electrolysis was carried out in acid solution, with the acid solution being exchanged for a pure base electrolyte (e.g. an acetate buffer) for the stripping step. The stripping step was monitored by d.c., differential pulse and Kalousek commutator voltammetry and the three methods were compared. A stationary mercury-drop electrode can generally be used for all the methods, whereas a mercury-film electrode is suitable only for the d.c. voltammetric determination of copper, lead and cadmium, as pulse measurements with films are poorly reproducible and the electrodes are easily damaged. The relative standard deviation does not exceed 20%. Some samples contained relatively large amounts of copper, which is best separated by electrodeposition on a platinum electrode.     

A rapid complexometric scheme for analysis of iron, aluminium, calcium and magnesium in slags

A simple and rapid complexometric method has been developed for the simultaneous determination of iron, aluminium, calcium and magnesium in a single solution in slags. Phosphorous and small amounts of chromium (1.5 mg) and vanadium (1 mg) do not interfere in the titration. Titanium and manganese are suitably masked with lactic acid and tetra sodium pyrophosphate, respectively. In a suitable aliquot, iron is titrated at pH 2 with EDTA, using sulphosalicylic acid as indicator. To this solution, excess disodium 1,2-cyclohexane diamine tetra acetic acid (DCTA) is added and aluminium is titrated by titrating the excess DCTA with standard copper sulphate solution at pH 3.5, using 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator. A known excess of EDTA is added, the pH is raised to 10 and calcium and magnesium are jointly titrated by titrating the excess EDTA with copper sulphate solution, using PAN indicator. The Ca-EDTA complex is demasked with ammonium oxalate at pH 5 and the released EDTA equivalent to calcium is titrated with copper sulphate solution at pH 10 with PAN indicator. Results of analysis compare favourably with certified values and values obtained by standard methods for BCS and other slags. A set of five samples can be analysed for iron, aluminium, calcium and magnesium in four hours as compared to three days by the classical conventional method.     

Spectrophotometric determination of silicon in ferrophosphorus

A method is described for the spectrophotometric determination of 0-4% silicon in ferrophosphorus, following fusion with sodium peroxide in a zirconium crucible. Silicomolybdic acid is formed with sodium molybdate. The acidity is increased to 2N and the solution stood for 10 min to destroy phosphomolybdic and arsenomolybdic acids. The silicomolybdic acid is reduced with ascorbic acid and the absorbance measured at 810 nm. The colour is stable, and a standard deviation of 0.006% was achieved for 0.7% silicon. Results obtained for three samples with alternative procedures are compared.     

Pollution-free method for the determination of iron in iron ore

A method for the determination of total iron in iron ores and concentrates is described which avoids the use of mercuric chloride. The sample is decomposed either by an acid attack or by fusion with sodium peroxide. The hot sample solution in about 6M hydrochloric acid is treated with hot 10% stannous chloride solution till pale yellow, followed by addition of a slight excess of 2% titanous chloride solution; the excess is then oxidized with perchloric acid (1 + 1). The solution is rapidly cooled in ice-water, and the iron (II) is titrated with potassium dichromate (sodium diphenylsulphonate as indicator). The results show the same degree of precision, accuracy, and degree of interference as those obtained by the standard stannous chloride-mercuric chloride method.     

电感耦合等离子体原子发射光谱法测定锰矿石中主次量元素

传统的化学分析方法分析矿石中主次量元素流程长,效率低。受干扰影响大,耗费大量人力物力,采用电感耦合等离子体原子发射光谱法测定技术对锰矿中的主次量元素进行了研究,主要测定了铝、铜、钙、铁、钾、镁、锰、钠、镍、磷、钛、锌等13种元素的含量。仪器采用射频功率1 150W,雾化器流速为0.70L/min,辅助器流速0.50L/min,观测高度12mm的测定条件。采用硝酸、盐酸、氢氟酸、高氯酸四酸溶矿,实验表明,溶液中分别共存200mg/L以下的钾、钠、钙、镁、钒、锰,对各微量元素的测定基本没有干扰。分析方法的检出限0.0002%~0.0065%。相对标准偏差(RSD)3.7%。均符合DZ/T0130—2006地质矿产实验室测试质量管理规范中精密度和准确度的控制指标。     

EDTA络合滴定法快速测定矿石中钙、镁

试样用盐酸、硝酸、氢氟酸、高氯酸分解,在pH值为6～9时,经六次甲基四胺-铜试剂分离铁、铝、镍、钴、铅、锌、铜、镉、锰等干扰元素后,在pH=10的氨水和氯化铵缓冲溶液中,以酸性铬蓝K-萘酚绿B为指示剂,用EDTA络合滴定法测定钙镁合量;另在氢氧化钾溶液中,用钙试剂为指示剂,以EDTA络合滴定法测定钙量,从而计算镁的含量。当样品钙高镁低或者镁高钙低时,低含量的镁量或钙量(<5%)可用电感耦合等离子体原子发射光谱(ICP-AES)法准确测定,使结果更准确。实验中对三个标准样品中的钙和镁进行多次测定,结果与认定值相符,相对标准偏差在0.69%～1.3%(n=7),加标回收率在99%～102%。方法实用性强,已经成功应用于各类矿石中钙镁的检测。     

电感耦合等离子体原子发射光谱法同时测定高强度玻璃纤维粉体中9种金属元素

建立电感耦合等离子体原子发射光谱法测定高强度玻璃纤维粉体中铝、镁、钙、铁、钛、锂、铈、钠、钾9种金属元素含量的方法。采用氢氟酸、高氯酸和盐酸分两段溶解样品,分别在选定的各元素分析谱线下,采用电感耦合等离子体原子发射光谱仪测定各元素含量。9种金属元素在各自的质量浓度范围内与光谱强度成良好的线性关系,相关系数均大于0.999,检出限为8.0~17.4 μg/g。测定结果的相对标准偏差小于1.8%(n=6),加标回收率为97.6%~103.7%。该方法准确,简便,快速,适用于高强度玻璃纤维中多金属元素的同时测定。