Preparation and optical properties of Bi2S3 microcrystallite doped glass and thin film by the sol-gel process

The Bi₂S₃ microcrystallite doped thin films and glass lumps have been successfully prepared by the sol-gel process from the hydrolysis of a complex solution of Si(OC₂H₅)₄ Bi(NO₃)₃ · 5H₂O and SC(NH₂)₂, and the size of the microcrystallites in glass heated for different times at 400°C was decided by the method of HRTEM. The optical transmission valley shifted towards longer wavelengths with longer heat-treatment time at 500°C in the Bi₂S₃ doped thin films, showing the experimental evidence of quantum size effects. The red-shift of emission peaks in luminenscence spectrum excited with longer wavelength is attributed to the broad distribution of particle size in Bi₂S₃ doped glass.     

Structure and Optical Properties of 0.1BiFeO3-0.9SrBi2Nb2O9 Thin Films Using a Modified Sol-Gel Technique

Fe-doped SrBi₂Nb₂O₉ precursor solution was synthesized using bismuth nitrate Bi(NO₃)₃·5H₂O, strontium nitrate Sr(NO₃)₂, iron nitrate Fe(NO₃)₃·9H₂O, and niobium ethoxide Nb(OC₂H₅)₅ as starting materials, ethylene glycol monomethyl ether (C₃H₈O₂) as the solvent. 0.1BiFeO₃-0.9SrBi₂Nb₂O₉ thin films were prepared on fused quartz substrates using sol-gel processing. The surface morphology and crystal structure and optical properties of the thin films were investigated. The thin film annealing at 400°C were found to be amorphous, and the thin films crystallize to a perovskite structure after a post-deposition annealing at 600°C for 1 h in air. The grain of thin film was evenly distributed. The thin films exhibit the designed optical transmission, while the optical transition is indirect in nature. Their optical band gap is about 2.5 eV.     

H2O + Fe(NO3)3 + Ni(NO3)2 ternary system isotherms at 0 °C and 30 °C

H₂O + Ni(NO₃)₂ binary system were investigated in the temperature range from −25 °C to 55 °C. The solid-liquid equilibria of the ternary system H₂O + Fe(NO₃)₃ + Ni(NO₃)₂ were studied using a synthetic method based on conductivity measurements. Tow isotherms were established at 0 °C and 30 °C, and the appearing stable solid phases are iron nitrate nonahydrate (Fe(NO₃)₃·9H₂O), iron nitrate hexahydrate (Fe(NO₃)₃·6H₂O), nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O) and nickel nitrate tetrahydrate (Ni(NO₃)₂·4H₂O).     

Visible Up-Conversion Luminescence in Ho3+: BaTiO3 Nano-Crystals Prepared by Sol Gel Technique

Visible up-conversion emissions at (435, 545, 580, 675 and 690 nm) and (437, 547 575 and 675 nm) have been observed from the sol-gel derived nano-crystalline Ho³⁺: BaTiO₃ powders and thin films respectively, under 808 nm laser diode excitation emissions. Combined with the energy level structure of Ho³⁺ ions and the kinetics of the visible emissions, the up-conversion mechanism has been analyzed and explained. The blue, green and red emissions of both samples has been attributed to the ground state-directed transition from (⁵F₁), (⁵S₂) and (⁵F₅), which are populated through excited state absorption (ESA) for 808 nm excitation. Nano-structure pure barium titanate and doped with different concentrations of Ho³⁺ ions in the from of powder and thin film have been prepared by sol-gel technique, using barium acetate (Ba(Ac)₂), and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The thin films were prepared by sol-gel spin coating method. The as-grown thin films and powders were found to be amorphous, which crystallized to the tetragonal phase after heating at 750°C in air for 30 minutes. The crystallite sizes of the thin film and powder both doped with 4% Ho³⁺ ions was found to be equal to 11 and 16 nm, respectvely.     

Ba Titanate and Barium/Strontium Titanate Thin Films from Hydroxide Precursors: Preparation and Ferroelectric Behavior

Randomly oriented ferroelectric BaTiO₃ and (Ba_0.6Sr_0.4) TiO₃ thin films on platinum coated Si (100) were prepared by a sol-gel method. The precursor solutions were derived from barium hydroxide or a mixture of barium/strontium hydroxides dissolved in acetic acid and titanium butoxide. Polarization versus applied voltage hysteresis studies indicated a remanent polarization of 3 µC/cm² and a coercive field of 43.4 kV/cm for BaTiO₃ films annealed at 800°C for 1 h. Corresponding parameters for (Ba_0.6Sr_0.4)TiO₃ films annealed at 800°C were found to be 7.2 µC/cm² and 102.7 kV/cm, respectively. Microstructural study of the surface morphology of these films indicated grains of less than 0.1 µm in size. The leakage current for (Ba_0.6Sr_0.4)TiO₃ films was found to be two orders of magnitude lower than that for BaTiO₃ films.     

Preparation of Forsterite (Mg2SiO4) Powders Via an Aqueous Route Using Magnesium Salts and Silicon Tetrachloride (SiCl4)

Forsterite (Mg₂SiO₄) powders were prepared by mixing SiCl₄ with aqueous solutions of either Mg(CH₃COO)₂·4H₂O or Mg(NO₃)₂·6H₂O and heating the powdered gel. The powders were characterised using thermal analysis (DTA and TGA), X-ray diffraction (XRD), nitrogen adsorption surface area analysis (BET) and transmission electron microscopy (TEM). On heating, MgO and enstatite (MgSiO₃) were observed in addition to forsterite. On heating to 1200°C, forsterite was the dominant phase in the powders produced from Mg(NO₃)₂·6H₂O, and MgO was the dominant phase in the powders produced from Mg(CH₃COO)₂·4H₂O. The primary particle sizes of these powders were between 100 and 500 nm, which remained the same on heat treatment. However, higher temperatures gave rise to an increase in the size and densities of the agglomerates of primary particles.     

Preparation of an aluminum oxo-hydroxide gel in organic medium

A new method has been developed to prepare aluminum oxohydroxide containing spinnable material and gel. Partial hydrolysis of Al(NO₃)₃·9H₂O in 1-propanol at 78°C produces a spinnable, viscous mixture. The role of the propanol in the hydrolysis proved to be to decrease the polarity of the solvent. In this medium the dissociation of nitric acid is driven back and it decomposes to nitrous gases resulting in the increase of pH in the solution. The conditions have been optimized to obtain the highest hydrolysis degree and to avoid precipitation of basic aluminum nitrate. The resulting optimal temperature is 76–80°C, the time needed is at least 15 h in the case of a laboratory scale preparation. Increasing the ratio of propanol: water and the concentration of Al(III) to the maximum value, leads to the decomposition of 54% of the initial amount NO ₃ ^– ion. By careful drying, the decomposition continues to about 70% and a solid foam comes into existence from the viscous mixture. This foam is able to swell in water, the degree of swelling in mass is about 10. The drying of swollen gel was examined. The spinnable mixture most likely contains polymer chains built up by H-bonds, the foam and the gel probably contain platelets.     

Preparation and Spectroscopic Characterization of Blue CoAl2O4 Coatings

Optically selective thin films of CoAl₂O₄ with a spinel structure were produced for an automotive lamps application by the sol-gel process using aluminum sec-butoxide, ethylacetoacetate chelating agent and cobalt nitrate hexahydrate. The use of two metal-oxide precursors is advantageous over the single bimetallic alkoxide precursor (aluminum cobalt isopropoxide), because it allows us to vary the Co/Al ratio in the precursor solution. We found that the Co/Al ratio should not exceed 0.3 if we are to achieve films with the characteristic blue colour at 700°C. The structural characteristics of the oxide powders were determined from infrared (IR) spectra and X-ray diffraction (XRD) analysis, while the optical properties of the films were investigated with UV-VIS spectroscopy.     

Orientation and Surface Properties of Sol-Gel Derived Y2O3 Films

The orientation, surface and optical properties of sol-gel derived Y₂O₃ films have been investigated. Transparent Y₂O₃ films were prepared on quartz glass substrates by sol-gel processes using YCl₃·6H₂O as a starting material. The water droplet contact angles of the films reached constant values between 79° and 90° after the films were left for 8 to 10 days in air at ambient temperature, indicating that the film surface exhibited hydrophobicity. When 2-(2-methoxyethoxy)ethanol (MEE) was added to the sol, yttria in the films crystallized to a strongly oriented cubic phase at firing temperatures between 400°C and 500°C. The intensity of the XRD peaks increased as the firing temperature was increased to 900°C. However, yttria crystallized to a non-oriented cubic phase when MEE was not used. The refractive index and packing density of the Y₂O₃ films increased from 1.55 to 1.68 and from 0.67 to 0.79, respectively, as the firing temperature was raised from 400°C to 900°C, indicating that sol-gel derived Y₂O₃ films are lower in density than evaporated ones.     

Preparation of La0.75Sr0.25MnO3 Nano-Phase Powders and Films from Alkoxide Precursors

The first purely alkoxide-based sol-gel route to nano-phase powders and thin films of perovskite La_0.75Sr_0.25MnO₃ is described. The phase and microstructure evolution on heat treatment of free gel films to form the target nano-phase oxide were investigated by TGA, IR spectroscopy, powder XRD, SEM and TEM-EDS. The xerogel consisted of a hydrated oxo-carbonate, without remaining alkoxo groups or solvent. Heating at 5°C·min^–1 decomposed the carbonate groups and yielded the pure perovskite La_0.75Sr_0.25MnO₃ at 760°C. The cell dimensions were virtually unchanged from the first observation of perovskite at 680°C, to 1000°C, 4 h. The monoclinic cell of La_0.75Sr_0.25MnO₃ obtained at 1000°C, 4 h, had the dimensions a = 5.475(1), b = 5.504(2), c = 7.771(1) Å, = 90.50(2), fitting the literature data quite well. Crack-free, homogenous, 150 nm thick La_0.75Sr_0.25MnO₃ films were prepared by spin-coating Si/SiO₂/TiO₂/Pt and polycrystalline -Al₂O₃ substrates with a 0.6 M alkoxide solution, followed by heating at 5°C·min^–1 to 800°C, 30 min.     

Sol-gel synthesis of nanocomposite materials based on lithium niobate nanocrystals dispersed in a silica glass matrix

With the final goal to obtain thin films containing stoichiometric lithium niobate nanocrystals embedded in an amorphous silica matrix, the synthesis strategy used to set a new inexpensive sol-gel route to prepare nanocomposite materials in the Li₂O-Nb₂O₅-SiO₂ system is reported. In this route, LiNO₃, NbCl₅ and Si(OC₂H₅)₄ were used as starting materials. The gels were annealed at different temperatures and nanocrystals of several phases were formed. Futhermore, by controlling the gel compositions and the synthesis parameters, it was possible to obtain LiNbO₃ as only crystallizing phase. LiNbO₃-SiO₂ nanocomposite thin films on Si-SiO₂ and Al₂O₃ substrates were grown. The LiNbO₃ average size, increasing with the annealing temperature, was 27 nm for a film of composition 10Li₂O-10Nb₂O₅-80SiO₂ heated 2 h at 800 °C. Electrical investigation revealed that the nanocrystals size strongly affects the film conductivity and the occurrence of hysteretic current-voltage curves.     

Preparation and Optical Characterization of Sol-Gel Deposited Pb(Zr0.45Ti0.55)O3 Films

Homogeneous crack-free lead zirconate titanate (Pb(Zr_0.45Ti_0.55)O₃: PZT 45/55) films were prepared by a chemically modified sol-gel process using lead acetate trihydrate, zirconium n-propoxide, and titanium isopropoxide precursors. The coating solutions were modified by the addition of diethanolamine. Single and multilayer films were deposited with a 2000 rpm spin rate on fused silica and MgO(100) substrates. Multiple spin coating with an intermediate heat treatment in air at 400°C for 3 min between coatings was performed to obtain films up to 2 m in thickness. The formation of the tetragonal perovskite structure was found to depend on the intermediate firing temperature, final annealing temperature, and annealing time. A 650°C rapid thermal annealing treatment in oxygen was required to crystallize the PZT film into the perovskite structure. The films were characterized using optical spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and thermo-gravimetry and differential scanning calorimetry (TG-DSC). The optical constants of the PZT films were evaluated from spectral transmittance and reflectance measurements. Optical constants are presented over the visible and near infrared region.     

Evolution of Structure of the Precursor During Sol-Gel Processing of ZnO and Low Temperature Formation of Thin Films

ZnO thin films were prepared on silicon substrate with Pt electrode by the sol-gel processing using Zn alkoxide solution prepared from Zn(NO₃)₂·6H₂O and 2-methoxyethanol. FT-IR spectroscopy showed the presence of Zn species in the alkoxide, with methoxyethoxide and nitrato groups as coordination ligands, indicating formation of Zn(NO₃)(OCH₂CH₂OCH₃). Smooth and homogeneous thin films were obtained by heat treating coating gel films in the temperature range from 250 to 500°C. The ZnO thin films exhibited a preferred growth of crystals with c-axis perpendicular to the Si substrate surface when fired at 250°C. It was discussed that the presence of nitrogen atoms in precursors had affected the phase development of crystals and was the basis of the structural relaxation for crystallization at low temperature.     

Preparation of Alumina Supported Palladium Catalysts by Sol-Gel Method

The chemical reactivity of the aluminium-sec-butoxide (ASB) and the palladium acetylacetonate Pd(acac)₂, used as precursors for the preparation of the alumina supported palladium catalysts by sol-gel method was investigated by the spectroscopic study of the precursor mixture during ageing, using FTIR, UV-VIS and ²⁷Al NMR. The obtaind results showed that acetylacetonate ligands were linked to aluminum when the mixture was aged at 40°C. This was proved by the bands observed at 1530 and 1600 cm^–1 in the FTIR spectra, the band obtained at 289 nm in the UV-VIS spectra and the ²⁷Al NMR sharp peak at 3 ppm. Furthermore, in order to avoid the Pd(acac)₂ reduction to metallic palladium by the SB occurring when the mixture is aged for 3 h, an optimum ageing time should be selected. The precursors modification and the preservation of the palladium oxidation state during ageing could be the required conditions to create a bond between palladium and aluminium during the gelation step. This should be the reason of the thermal stability improvement of the alumina supported palladium catalyst prepared by the sol-gel method.     

Low-temperature processing of sol-gel derived Pb(Zr,Ti)O<Subscript>3</Subscript> thick films using CO<Subscript>2</Subscript> laser annealing

Fabrication of ferroelectric Pb(Zr_0.52Ti_0.48)O₃ (PZT) thick films on a Pt/Ti/SiO₂/Si substrate using powder-mixing sol-gel spin coating and continuous wave CO₂ laser annealing technique to treat the specimens with at a relatively low temperature was investigated in the present work. PZT fine powders were prepared by drying and pyrolysis of sol-gel solutions and calcined at temperatures from 400 to 750°C. After fine powder-containing sol-gel solutions were spin-coated on a substrate and pyrolyzed, CO₂ laser annealing was carried out to heat treat the specimens. The results show that laser annealing provides an extremely efficient way to crystallize the materials, but an amorphous phase may also form in the case of overheating. Thicker films absorb laser energy more effectively and therefore melt at shorter periods, implying a significant volume effect. A film with thickness of 1 μm shows cracks and rough surface morphology and it was difficult to obtain acceptable electrical properties, indicating importance of controlling interfacial stress and choosing appropriate size of the mixing powders. On the other hand, a thick film of 5 μm annealed at 100 W/cm² for 15 s exhibits excellent properties (P _r = 36.1 μC/cm², E _c = 19.66 kV/cm). Films of 10 μm form a melting zone at the surface and a non-crystallized bottom layer easily at an energy density of 100 W/cm², showing poor electrical properties. Besides, porosity and electrical properties of thick films can be controlled using appropriate processing parameters, suggesting that CO₂ laser annealing of modified sol-gel films is suitable for fabricating films of low dielectric constants and high crystallinity.     

Improvement of the Pd/Al2O3 Catalyst by the Control of the Sol-Gel Preparative Parameters

In this work, the metal dispersion of the Pd/Al₂O₃ catalyst prepared by sol-gel method is improved by an adequate optimisation of the preparative variables. First, the gelation temperature and the ageing time are selected, in order to avoid the reduction of the metal precursor (palladium acetylacetonate, Pd(acac)₂) by the solvent (sec-butanol, sB). The metal sintering effect on the catalysts treated in oxygen at 500°C is then minimized when the alumina pore size is controlled by the variation of the alumium alkoxide (AsB) concentration and the acetic acid amount ([AcA]/[AsB]). The appearance of new palladium particles on the alumina surface and the matching between the particle diameters and the pore sizes were also effective for the metallic surface area improvement on the samples treated in oxygen at 800°C. Compared to the reference catalysts, the higher metal dispersion obtained on the sol-gel ones was the determinant factor for their higher catalytic activity in methane combustion.     

PbCu3(OH)(NO3)(SeO3)3·1/2H2O und Pb2Cu3O2(NO3)2(SeO3)2: Synthese und Kristallstrukturuntersuchung

Crystals of PbCu₃(OH)(NO₃)(SeO₃)₃·1/2H₂O [a=7.761(3)Å,b=9.478(4)Å,c=9.514(4)Å, =66.94(2)°, =69.83(2)°, =81.83(2)°, space group P ,Z=2] and Pb₂Cu₃O₂(NO₃)₂(SeO₃)₂ [a=5.884(2)Å,b=12.186(3)Å,c=19.371(4)Å, space group Cmc2₁,Z=4] were synthesized under hydrothermal conditions. Their crystal structures were refined with three-dimensional X-ray data toR _w=0.033 resp. 0.055. In PbCu₃(OH)(NO₃)(SeO₃)₃·1/2H₂O the Cu atoms are [4+1] and [4+2] coordinated and via SeO₃ groups a three-dimensional atomic arrangement is built up. In Pb₂Cu₃O₂(NO₃)₂(SeO₃)₂ there are sheets, which are connected only via Pb-O bonds ranging from 2.98 Å to 3.16 Å.

     

Preparation and Characterization of (Ba,Ca)(Ti,Zr)O3 Thin Films Through Sol-Gel Processing

(Ba_0.92,Ca_0.08)(Ti_0.92,Zr_0.08)O₃ thin films were prepared from Ba-Ti and Ca-Zr precursors by sol-gel processing. Polymerizable solutions containing Ba-Ti and Ca-Zr, respectively, were newly synthesized. Decomposition of the starting compounds and crystallization behavior of the film were examined by using TG/DTA and XRD. Microstructure of thin films was observed by using SEM. Polycrystalline (Ba_0.92,Ca_0.08)(Ti_0.92, Zr_0.08)O₃ films obtained by firing at 800°C were dense with fine grains. The thin films showed a dielectric constant of 1200 and dielectric loss of 0.5%.     

Preparation and Characterization of SiO2-MxOy(M = V, Sn, Sb) Thin Films from Silicic Acid and Metal Chlorides

The preparation of SiO₂-M _x O _y (M = V, Sn, Sb) binary oxide thin films by sol-gel method was investigated. The reaction of silicic acid with metal chloride (M = Sn and Sb) or oxychloride (M = V) formed homogeneous solutions. The dip-coating of slide glass and silicon wafer followed by heat treatment gave oxide films having Si—O—M bond. The changes of FT-IR spectra as a function of heat treatment temperature and molar composition confirmed the Si—O—M bonds. The sheet resistance of films increased with an increase on heat treatment temperature and decrease in the content of metal oxide M _x O _y . X-ray diffraction peaks were observed for the SiO₂-V₂O₅ films with high V₂O₅ contents and heat-treated above 250°C, while the others were amorphous. Oxide films heat treated at 500°C had a thickness between 340–470 nm.     

Spectroellipsometric Characterization of Multilayer Sol-Gel Fe2O3 Films

Multilayer Fe₂O₃ films were deposited by the sol-gel method on glass substrates using three successive deposition procedures. The films were thermally treated for 1 h at 300°C.The optical and microstructural properties of these films were investigated by spectroscopic ellipsometry (SE) in the 500–1000 nm range. The optical gap was found by fitting the dispersion of the film refractive index (n) with the Wemple-DiDomenico (WDD) formula.The ellipsometric measurements showed also that the Fe₂O₃ films are anisotropic. The birefringence values (n) of the sol-gel films (0.05–0.08) are smaller than the large values of the Fe₂O₃ (which are around 0.28) but increase with the crystalization of the films. AFM mesurements showed that the films treated at 300°C start to crystallize.