Preparation and electrical properties of the 0,37Li2S-0,18P2S5-0,45LiI glass

A new lithium vitreous electrolyte has been found in the LiI---Li₂S---P₂S₅ system. LiI concentration in the glass, 45% moles, is close to the solubility limit of LiI in 2Li₂S---P₂S₅ glass.The activation energy is of the order of 7.2 Kcal.mole⁻¹ and the conductivity value is 10⁻³ (ohm cm)⁻¹ at 25°C. The conduction is ionic and assured by Li⁺ ions.     

Analysis of the 2ν3 band of CD3F at 5.06 μm recorded under high resolution

The 2ν₃(A₁) band of ¹²CD₃F near 5.06 μm has been recorded with a resolution of 20–24 × 10⁻³ cm⁻¹. The value of the parameter (α^B − α^A) for this band was found to be very small and, therefore, the K structure of the R(J) and P(J) manifolds was unresolved for J < 15 and only partially resolved for larger J values. The band was analyzed using standard techniques and values for the following constants determined: ν₀ = 1977.178(3) cm⁻¹, B″ = 0.68216(9) cm⁻¹, D″_J = 1.10(30) × 10⁻⁶ cm⁻¹, α^B = (B″ − B′) = 3.086(7) × 10⁻³ cm⁻¹, and β^J = (D″_J − D′_J) = −3.24(11) × 10⁻⁷ cm⁻¹. A value of α^A = (A″ − A′) = 2.90(5) × 10⁻³ cm⁻¹ has been obtained through band contour simulations of the R(J) and P(J) multiplets.     

The bending energy levels of C2H2

Absorption spectra of C₂H₂ have been recorded between 50 and 1450 cm⁻¹, with a resolution always better than 0.005 cm⁻¹, using two different Fourier transform spectrometers. Analysis of the data provided two sets of results. First, the bending levels with Σ_t V_t(t = 4, 5) ≤ 2 were characterized by a coherent set of 34 parameters derived from the simultaneous analysis of 15 bands, performed using a matrix Hamiltonian. The following main parameters were obtained (in cm⁻¹): ω₄⁰ = 608.985196(14), ω₅⁰ = 729.157564(10); B₀ = 1.17664632(18), α₄ = −1.353535(86) × 10⁻³, α₅ = −2.232075(40) × 10⁻³; q₄⁰ = 5.24858(12) × 10⁻³, and q₅⁰ = 4.66044(12) × 10⁻³, with the errors (1σ) on the last quoted digit. Second, a more complete set of bending levels with Σ_t V_t ≤ 4, some of which have never previously been reported, and also including V₂ = 1 have been fitted to 80 parameters. This simultaneous fit involved 43 bands and used the same full Hamiltonian matrix. Some perturbations which affect the higher excited levels are discussed.     

Line Positions and Intensities of the ν1+ ν2+ 3ν3, ν2+ 4ν3, and 3ν1+ 2ν2Bands of Ozone

Using a Fourier transform spectrometer, we have recorded the spectra of ozone in the region of 4600 cm⁻¹, with a resolution of 0.008 cm⁻¹. The strongest absorption in this region is due to the ν₁+ ν₂+ 3ν₃band which is in Coriolis interaction with the ν₂+ 4ν₃band. We have been able to assign more than 1700 transitions for these two bands. To correctly reproduce the calculation of energy levels, it has been necessary to introduce the (320) state which strongly perturbs the (113) and (014) states through Coriolis- and Fermi-type resonances. Seventy transitions of the 3ν₁+ 2ν₂band have also been observed. The final fit on 926 energy levels withJ_max= 50 andK_max= 16 gives RMS = 3.1 × 10⁻³cm⁻¹and provides a satisfactory agreement of calculated and observed upper levels for most of the transitions. The following values for band centers are derived: ν₀(ν₁+ ν₂+ 3ν₃) = 4658.950 cm⁻¹, ν₀(3ν₁+ 2ν₂) = 4643.821 cm⁻¹, and ν₀(ν₂+ 4ν₃) = 4632.888 cm⁻¹. Line intensities have been measured and fitted, leading to the determination of transition moment parameters for the two bands ν₁+ ν₂+ 3ν₃and ν₂+ 4ν₃. Using these parameters we have obtained the following estimations for the integrated band intensities,S_V(ν₁+ ν₂+ 3ν₃) = 8.84 × 10⁻²²,S_V(ν₂+ 4ν₃) = 1.70 × 10⁻²², andS_V(3ν₁+ 2ν₂) = 0.49 × 10⁻²²cm⁻¹/molecule cm⁻²at 296 K, which correspond to a cutoff of 10⁻²⁶cm⁻¹/molecule cm⁻².     

Effect of oxygen partial pressure on the structural and optical properties of dc reactive magnetron sputtered molybdenum oxide films

Molybdenum oxide films (MoO₃) were deposited on glass and crystalline silicon substrates by sputtering of molybdenum target under various oxygen partial pressures in the range 8 × 10⁻⁵–8 × 10⁻⁴ mbar and at a fixed substrate temperature of 473 K employing dc magnetron sputtering technique. The influence of oxygen partial pressure on the composition stoichiometry, chemical binding configuration, crystallographic structure and electrical and optical properties was systematically studied. X-ray photoelectron spectra of the films formed at 8 × 10⁻⁵ mbar showed the presence of Mo⁶⁺ and Mo⁵⁺ oxidation states of MoO₃ and MoO_3−x. The films deposited at oxygen partial pressure of 2 × 10⁻⁴ mbar showed Mo⁶⁺ oxidation state indicating the films were nearly stoichiometric. It was also confirmed by the Fourier transform infrared spectroscopic studies. X-ray diffraction studies revealed that the films formed at oxygen partial pressure of 2 × 10⁻⁴ mbar showed the presence of (0 k 0) reflections indicated the layered structure of α-phase MoO₃. The electrical conductivity of the films decreased from 3.6 × 10⁻⁵ to 1.6 × 10⁻⁶ Ω⁻¹ cm⁻¹, the optical band gap of the films increased from 2.93 to 3.26 eV and the refractive index increased from 2.02 to 2.13 with the increase of oxygen partial pressure from 8 × 10⁻⁵ to 8 × 10⁻⁴ mbar, respectively.     

Preparation and electrical properties of a pyrochlore-related Ce2Zr2O8−x phase

A pyrochlore-related Ce₂Zr₂O_8−x phase has been prepared in a reduction reoxidation process from Ce_0.5Zr_0.5O₂ powders. Ce₂Zr₂O_8−x, based on a cubic symmetry with a=1.053 nm, decomposes in nitrogen at 800 °C, but remains stable up to 900 °C in air. It shows mixed oxygen ionic and electronic conductivity. The bulk conductivity at 700 °C is 4×10⁻⁴ S cm⁻¹ in air and 1×10⁻² S cm⁻¹ in nitrogen, and the activation energy is 1.27 eV in air. In nitrogen, the Arrhenius law is not obeyed, and a curved plot was obtained from 400 to 700 °C; then, the conductivity decreased rapidly due to the thermal decomposition of Ce₂Zr₂O_8−x.     

Spectral characterization and energy levels of Cr:Sc2(MoO4)3 crystal

This paper reports the spectral properties and energy levels of Cr³⁺:Sc₂(MoO₄)₃ crystal. The crystal field strength Dq, Racah parameter B and C were calculated to be 1408 cm⁻¹, 608 cm⁻¹ and 3054 cm⁻¹, respectively. The absorption cross sections σ_α of ⁴A₂→⁴T₁ and ⁴A₂→⁴T₂ transitions were 3.74×10⁻¹⁹ cm² at 499 nm and 3.21×10⁻¹⁹ cm² at 710 nm, respectively. The emission cross section σ_e was 375×10⁻²⁰ cm² at 880 nm. Cr³⁺:Sc₂(MoO₄)₃ crystal has a broad emission band with a broad FWHM of 176 nm (2179 cm⁻¹). Therefore, Cr³⁺:Sc₂(MoO₄)₃ crystal may be regarded as a potential tunable laser gain medium.     

Kerr property of cubic K0.95Li0.05Ta0.60Nb0.40O3 single crystal

The Kerr (quadratic electro-optic) property of K_0.95Li_0.05Ta_0.60Nb_0.40O₃ was measured by using an automated scanning Mach–Zehnder interferometer. K_0.95Li_0.05Ta_0.60Nb_0.40O₃ has large Kerr effect with R₁₁ = 7.2 × 10⁻¹⁶ m²/V² and R₁₂ = −1.2 × 10⁻¹⁶ m²/V² at 632.8 nm near its phase-transition temperature. The dielectric and Kerr properties as function of temperature were also investigated, thus the quadratic polarization-optic coefficients were calculated. The values of g₁₁ and g₁₂ are 0.083 m⁴/C² and −0.014 m⁴/C², respectively, and do not depend on temperature within the measurement accuracy of 5%.     

Line strength measurements of carbonyl sulfide (OCS) in the 2v3, v1+2v2+v3, and 4v2+v3 bands

To support planetary studies of the Venus atmosphere, we measured line strengths of the 2v₃, v₁+2v₂+v₃, and 4v₂+v₃ bands of the primary isotopologue of carbonyl sulfide (¹⁶O¹²C³²S), whose band centers are located at 4101.387, 3937.427, and 4141.212 cm⁻¹, respectively. For this, infrared absorption spectra in normal carbonyl sulfide (OCS) sample gas were recorded at an unapodized resolution of 0.0033 cm⁻¹ at ambient room temperatures using a Bruker Fourier transform spectrometer (FTS) at the Jet Propulsion Laboratory. The FTS instrumental line shape (ILS) function was investigated, which revealed no significant instrumental line broadening or distortions. Various custom-made short cells and a multi-pass White cell were employed to achieve optical densities sufficient to observe the strong 2v₃ and the weaker bands in the region. Gas sample impurities and the isotopic abundances were determined from mass spectrum analysis. Line strengths were retrieved spectrum by spectrum using a non-linear curve fitting algorithm adopting a standard Voigt line profile, from which Herman–Wallis factors were derived for the three bands. The band strengths of 2v₃, v₁+2v₂+v₃, and 4v₂+v₃ of ¹⁶O¹²C³²S (normalized at 100% of isotopologue) are observed to be 6.315(13)×10⁻¹⁹, 1.570(2)×10⁻²⁰, and 7.949(20)×10⁻²¹ cm⁻¹/molecule cm⁻², respectively, at 296 K. These results are compared with earlier measurements and the HITRAN 2004 database.     

Fourier Transform Spectroscopy of theYΣ–XΠiTransition of CuO

TheY²Σ⁺–X²Π_inear-infrared electronic transition of CuO was observed at high resolution for the first time. The spectrum was recorded with the Fourier transform spectrometer associated with the McMath–Pierce Solar Telescope at Kitt Peak. The excited CuO molecules were produced in a low pressure copper hollow cathode sputter with a slow flow of oxygen. Constants for theY²Σ⁺states of CuO are:T₀= 7715.47765(54) cm⁻¹,B= 0.4735780(28) cm⁻¹,D= 0.822(12) × 10⁻⁶cm⁻¹,H= 0.46(10) × 10⁻¹⁰cm⁻¹, γ = −0.089587(42) cm⁻¹, γ_D= 0.1272(79) × 10⁻⁶cm⁻¹,b_F= 0.12347(22) cm⁻¹, andc= 0.0550(74) cm⁻¹. ImprovedX²Π_iconstants are also presented.     

Large nonlinear optical properties of Fe2O3 nanoparticles

Nonlinear optical properties of Fe₂O₃ nanoparticles were investigated by the signal-beam Z-scan technique with Ar⁺ and Ne–He lasers. The largest reported effective nonlinear coefficient, n₂=−8.07×10⁻⁷ cm²/W, was obtained. It is demonstrated that the nonlinear optical response originals from quantum confinement effect.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

High-resolution infrared and millimeterwave spectra of the v3=1 vibrational state of NF3 at 907 cm

The ν₃^±1 perpendicular band of ¹⁴NF₃ ( cm⁻¹) has been studied with a resolution of 2.5 × 10⁻³ cm⁻¹, and 3682 infrared (IR) transitions (J_max=55, K_max=45) have been assigned. These transitions were complemented by 183 millimeterwave (MMW) rotational lines (J_max=25, K_max=19) in the 150–550 GHz region (precision 50–100 kHz). The kl=+1 level reveals a strong A₁/A₂ splitting due to the l(2,2) rotational interaction (q=−4.05 × 10⁻³ cm⁻¹) while the kl=−2 and +4 levels exhibit small A₁/A₂ splittings due to l(2,−4) and l(0,6) rotational interactions. All these splittings were observed by both experimental methods. Assuming the v₃=1 vibrational state as isolated, a Hamiltonian model of interactions in the D reduction, with l(2,−1) rotational interaction (r=−1.96 × 10⁻⁴ cm⁻¹) added, accounted for the observations. A set of 26 molecular constants reproduced the IR observations with σ_IR=0.175 × 10⁻³ cm⁻¹ and the MMW data with σ_MMW=134 kHz. The Q reduction was also performed and found of comparable quality while the QD reduction behaved poorly. This may be explained by a predicted Coriolis interaction between v₃=1 and v₁=1 (A₁, 1032.001 cm⁻¹) which induces a slow convergence of the Hamiltonian in the QD reduction but has no major influence on the other reductions. The experimental equilibrium structure could be calculated as: r_e(N–F)=1.3676 Å and (FNF)=101.84°.     

Rotational absorption spectrum of methylene fluoride in the 20–100 cm region

The pure rotational spectrum of CH₂F₂ was recorded in the 20–100 cm⁻¹ spectral range and analyzed to obtain rotation and centrifugal distortion constants. Analysis of the data yielded rotation constants: A = 1.6392173 ± 0.0000015, B = 0.3537342 ± 0.00000033, C = 0.3085387 ± 0.00000027, τ_aaaa = −(7.64 ± 0.46) × 10⁻⁵, τ_bbbb = −(2.076 ± 0.016) × 10⁻⁶, τ_cccc = −(9.29 ± 0.12) × 10⁻⁷, T₁ = (4.89 ± 0.20) × 10⁻⁶, and T₂ = −(1.281 ± 0.016) × 10⁻⁶cm⁻¹.     

The 2ν8 Band of CH3CN

The overtone band 2ν⁰₈ of CH₃CN around 720 cm⁻¹ has been measured on a Bruker Fourier transform spectrometer at a resolution of 0.003 cm⁻¹. Only the parallel band was observed, but due to the l(2, 2) resonance, ΔK = −2 lines leading to the v₈ = 2, l₈ = −2 levels with K = 1-3 could be seen. More information for the l₈ = ±2 component of the vibrational state v₈ = 2 was evaluated from the hot band 2ν^±2₈ - ν^±1₈. Altogether more than 1000 lines were assigned. In the fit pure rotational lines from literature were also combined. Among the results the anomalous A₀ - A′ values 4.6722(13) × 10⁻³ cm⁻¹ for the 2ν⁰₈ band and 7.0324(32) × 10⁻³ cm⁻¹ for the 2ν^±2₈ band are striking.     

High-resolution infrared spectra of HCF3 in the ν6 (500 cm) and 2ν6 (1000 cm) regions: rovibrational analysis and accurate determination of the ground state constants C0 and DK

The high-resolution infrared spectrum of HCF₃ was studied in the ν₆ fundamental (near 500 cm⁻¹) and in the 2ν₆ overtones (near 1000 cm⁻¹) regions. The present study reports on the analysis of the hot bands in the ν₆ region, as well as the first observation and assignment of the 2ν₆² perpendicular band. Using ν₆, 2ν₆^±2–ν₆^±1 and 2ν₆² experimental wavenumbers, accurate coefficients C₀ and D_K⁰ of the K-dependent ground-state energy terms were obtained, using the so-called “loop method.” Ground-state energy differences Δ(K,J)=E₀(K,J)−E₀(K−3,J) were obtained for K=3–30. A least-squares fit of 81 such differences gave the following results (in cm⁻¹): C₀=0.1892550(15); D_K⁰=2.779(26) × 10⁻⁷.     

High sensitivity CW-cavity ring down spectroscopy of CO2 near 1.35 μm (I): line positions

The absorption spectrum of carbon dioxide in natural isotopic abundance has been investigated by CW-cavity ring down spectroscopy with a new setup based on fibred distributed feedback (DFB) laser diodes. By using a series of 25 DFB lasers, the CO₂ spectrum was recorded in the 7123–7793 cm⁻¹ region with a typical sensitivity of 3×10⁻¹⁰ cm⁻¹. A 2125 transitions with intensities as low as 1×10⁻²⁹ cm/molecule were detected and assigned to the ¹²C¹⁶O₂, ¹⁶O¹²C¹⁷O and ¹⁶O¹²C¹⁸O isotopologues. For comparison, only 357 of them were previously reported from Venus spectra and 344 transitions were included in the 2004 version of the HITRAN database. The band by band analysis has led to the determination of the rovibrational parameters of 28, 2 and 6 bands for the ¹²C¹⁶O₂, ¹⁶O¹²C¹⁷O and ¹⁶O¹²C¹⁸O isotopologue, respectively. While the uncertainty on the experimental line positions is on the order of 5×10⁻⁴ cm⁻¹, the average deviation from the ¹²C¹⁶O₂ calculated values provided by the most recent version of the carbon dioxide spectroscopic databank (CDSD) is −2.8×10⁻³ cm⁻¹ with an root mean square (rms) deviation of 3.5×10⁻³ cm⁻¹. Maximum deviations in the order of 0.02 and 0.12 cm⁻¹ were evidenced for some bands of the ¹⁶O¹²C¹⁷O and ¹⁶O¹²C¹⁸O minor isotopologues. The obtained results improve significantly the previous measurements from Venus spectra and will be valuable to refine the sets of effective Hamiltonian parameters used to generate the CDSD database.     

High-resolution infrared study of the 2ν3 (A1, E) and ν1 + ν3 (E) bands of NF3

The 2ν₃ overtone (A₁, E) and the ν₁ + ν₃ (E) combination bands of the oblate symmetric top ¹⁴NF₃ were studied by FTIR spectroscopy with a resolution of 2.5 × 10⁻³ cm⁻¹. Nearly 500 lines up to K_max/J_max = 30/43 were observed for the weak A₁ component reaching the v₃ = 2⁰ substate (1803.1302 cm⁻¹), the majority of which corresponded to reinforced K = 3p-type transitions. For the strong E component reaching the v₃ = 2^±2 substate (1810.4239 cm⁻¹), about 3550 transitions were assigned up to K_max/J_max = 65/69, favoring a clear observation of the ℓ(4, −2) and ℓ(4, 4) splittings within the kℓ = −2 and +4 sublevels, respectively. The two v₃ = 2 substates are linked by the ℓ(2, 2)- and ℓ(2, −1)-type interactions, providing severe crossings, respectively, at K′ = 6 and near K′ = 24 on the v₃ = 2⁺² side. A model working in the D-reduction and including all these ℓ-type interactions could reproduce together 3695 nonzero weighted experimental data (NZW) through 33 free parameters with a standard deviation of σ = 0.357 × 10⁻³  cm⁻¹. As for the ν₁ + ν₃ (E) combination band, about 3690 lines were assigned up to K_max/J_max = 45/55. Its v₁ = v₃ = 1 upper state (1931.577 5 cm⁻¹) was treated using the same model recently applied to the v₃ = 1 (E, 907.5413 cm⁻¹) state. It yielded 21 free parameters through 3282 NZW experimental data, adjusted with σ = 0.344 × 10⁻³  cm⁻¹ in the D-reduction. For the two excited states, the small and unobserved ℓ(0, 6) interaction was tested as useless. To confirm the adequacy of the vibrationally isolated models used, some other reductions of the Hamiltonian were tried. For the v₃ = 2 state, the D-, L-, and LD-reductions led to similar σ’s, while the Q one was not successful. For the v₁ = v₃ = 1 state, the D- and Q-reductions gave comparable σ’s, while the QD-reduction was not as good. The corresponding unitary equivalence relations are generally more nicely fulfilled for the v₃ = 2 state than for the v₁ = v₃ = 1 state. The three derivable anharmonicity constants in cm⁻¹ are x₃₃ = −4.1528, g₃₃ = +1.8235 and x₁₃ = −7.9652.     

Polyacrylonitrile electrolytes: 1. A novel high-conductivity composite polymer electrolyte based on PAN, LiClO4 and α-Al2O3

In this work, a series of novel solid-type α-Al₂O₃-containing polyacrylonitrile (PAN)-based composite polymer electrolytes (CPE) with high conductivity and high mechanical property at room temperature has been prepared. The effect of the addition of α-Al₂O₃ on the properties of the PAN-based composite polymer electrolyte has been analyzed. The best conductivities obtained at room temperature is 5.7×10⁻⁴ S cm⁻¹ from the CPE with 7.5 wt.% α-Al₂O₃ and 0.6 LiClO₄ per PAN repeat unit. The stress–strain test result indicates that the membranes prepared possess high yield stress (73 kg cm⁻²) suitable for serving as separators in the solid-state lithium and lithium ion batteries and high yield elongation (225%) pliable to form good interface with electrodes. Also discussed are the effects of the addition of the ceramics on the interactions in the system and the possible conduction mechanism.     

New ground state constants of CH3Cl and CH3Cl from global polyad analysis

A global analysis of the infrared spectrum of chloromethane involving the ground state and the 13 vibrational states lying up to 2600 cm⁻¹ was recently achieved using high resolution Fourier transform spectra of pure isotopomers. More than 20 000 transitions (cold and hot bands) for each isotopomer ¹²CH₃³⁵Cl and ¹²CH₃³⁷Cl have been assigned and fitted with a standard deviation of about 3 × 10⁻⁴ cm⁻¹ close to the experimental precison. As part of this global effort, improved ground state constants up to sextic centrifugal distortion terms have been determined for each isotopomer taking advantage of the numerous allowed and perturtation-allowed transitions simultaneously fitted using our global model. The axial constants could be determined from ΔK ≠ 0 combinations arising from rovibrational local resonances within Polyads 3 and 5.