氯铝酸离子液体酸性的吡啶探针红外光谱研究

利用吡啶探针红外光谱法研究了氯铝酸离子液体的酸性,发现当氯铝酸离子液体A lC l3的摩尔分数x为0.4~0.5时,离子液体表现出弱Lew is酸的红外特性。对吡啶探针吸附Lew is酸位A l2C l7-、A lC l4-、A l2C l6和A lC l3的各振动模式红外特征峰峰位进行了归属,通过红外特征峰峰位置和峰面积可以指示离子液体的酸强度。利用吡啶探针递增吸附法考察了吡啶递增吸附对氯铝酸离子液体酸性位的影响。研究发现,当吡啶量增加到一定程度时,Py-A l2C l7-配位络合物容易与吡啶发生反应生成Py-A lC l4-和Py-A lC l3配位络合物,从而导致离子液体的吡啶吸附红外特征峰发生变化。     

1-乙基-3-丁基苯并咪唑六氟化磷离子液体液相微萃取剂的制备与应用

合成了1-乙基苯并咪唑（eBim）、1-乙基-3-丁基苯并咪唑溴(C4eBimBr)中间体和1-乙基-3-丁基苯并咪唑六氟化磷(C4eBimPF6)离子液体。 通过红外光谱和核磁共振波谱表征了各步反应产物的结构。 基于离子液体分散液相微萃取-高效液相色谱法分析了水中邻苯二甲酸辛酯(DOP)和邻苯二甲酸壬酯(DNP)。 考察了萃取温度、萃取时间和离子液体用量对DOP和DNP萃取效果的影响。 在1.0～10 μg/L范围内,DOP和DNP的色谱峰高与质量浓度分别呈线性关系,相关系数（r2）分别为0.984 7和0.987 2。 DOP和DNP的最低检出限分别为0.018和0.052 μg/L,加标回收率分别为94.3%~102%和93.5%~103%。     

OsO(4) in ionic liquid [Bmim]PF(6): a recyclable and reusable catalyst system for olefin dihydroxylation. remarkable effect of DMAP

[reaction: see text] The combination of the ionic liquid [bmim]PF(6) and DMAP provides a most simple and practical approach to the immobilization of OsO(4) as catalyst for olefin dihydroxylation. Both the catalyst and the ionic liquid can be repeatedly recycled and reused in the dihydroxylation of a variety of olefins with only a very slight drop in catalyst activity.     

电极/离子液体界面电容

用电化学阻抗方法研究了铂片电极在BMIMPF6,BMIMBF4,BMIMClO4,BMIMTf2N,BMIMCl,BMIMBr,C3OHMIMBF4,C3OHMIMClO4和BMMIMPF6(BMIM:1-butyl-3-methylimidazolium;C3OHMIM:1-(3-hydroxypropyl)-3-methylimidazolium;BMMIM:1-butyl-2-methyl-3-methylimidazolium;Tf2N:bis(trifluoromethylsulfonyl)amide)等离子液体中的界面电容及结构.结果表明:当阴、阳离子半径相差不大且不存在特性吸附时,在零电荷电势附近,电极/离子液体界面的电容-电势曲线将出现电容单峰或者双峰.电极的零电荷电势对应于单峰的峰电势或者双峰之间的谷电势.当电极电势远离零电荷电势时,电极/离子液体界面成紧密层结构,可由紧密层理论来描述.如果存在离子的特性吸附,相应的电容峰可能不再出现,而表现为双层电容随电极电势对零电荷电势的偏离而单调增加.还研究了添加小的Li+离子对电极/离子液体界面电容的影响.通过向BMIMTf2N中加入LiTf2N,发现Li+离子可以改变电极/离子液体界面的双层结构,但无助于界面电容的提高,甚至可能引起电容的降低.最后探讨了不同条件下,尤其考虑阴阳离子特性吸附时,电极/离子液体的界面结构.     

Heavy metals adsorption by novel EDTA-modified chitosan-silica hybrid materials

Ionic liquid based microemulsions were characterized by absorption solvatochromic shifts, (1)H NMR and kinetic measurements in order to investigate the properties of the ionic liquid within the restricted geometry provided by microemulsions and the interactions of the ionic liquid with the interface. Experimental results show a significant difference between the interfaces of normal water and the new ionic liquid microemulsions. Absorption solvatochromic shift experiments and kinetic studies on the aminolysis of 4-nitrophenyl laurate by n-decylamine show that the polarity at the interface of the ionic liquid in oil microemulsions (IL/O) is higher than at the interface of water in oil microemulsions (W/O) despite the fact that the polarity of [bmim][BF(4)(-)] is lower than the polarity of water. (1)H NMR experiments showed that an increase in the ionic liquid content of the microemulsion led to an increase in the interaction between [bmim][BF(4)(-)] and TX-100. The reason for the higher polarity of the microemulsions with the ionic liquid can be explained in terms of the incorporation of higher levels of the ionic liquid at the interface of the microemulsions, as compared to water in the traditional systems.     

Solubilization of an Ionic Liquid,l-Butyl-3-methylimidazolium Hexafluorophosphate,in a Surfactant-Water System

The amphiphilic association structures were determined in the system; water, Laureth 4 (approximately C₁₂(EO) ₄), and the ionic liquid l-butyl-3-methylimidazolium hexafluorophosphate ([bmim[PF₆]), using visual observation and small angle x-ray diffraction. The system showed a lamellar liquid crystal solubilizing the ionic liquid ([bmim[PF₆]) to a maximum of 15%, an isotropic surfactant solution dissolving the ionic liquid to a maximum of 39%, an isotropic ionic liquid solution with less than 0.5% of water and surfactant and finally, an aqueous solution with only traces of surfactant and ionic liquid. The small angle x-ray diffraction results showed the ionic liquid to be solubilized into the lamellar liquid crystal without changing the dimensions of the amphiphile layer or the interlayer spacing dependence on the water content.     

吡啶类离子液体萃取-氧化脱除含硫化合物

制备了N-丁基吡啶四氟硼酸盐离子液体([BPy]BF₄), 考察了其对含有噻吩和二苯并噻吩的模型油萃取脱硫的效果. 在此基础上以离子液体为萃取剂, 以过氧化氢(质量分数30%)为氧化剂, 研究了其对模型油进行萃取-氧化脱硫的效果, 结果表明, 当V([BPy]BF₄)∶V(Oil)∶V(H₂O₂)=1∶1∶0.4时, 在55 ℃下进行萃取-氧化脱硫30 min, 噻吩和二苯并噻吩的脱硫率分别达到78.5%和84.3%; 将该萃取-氧化体系应用于实际汽油体系, 脱硫率达到56.3%; 对使用过的离子液体进行再生处理, 重复使用4次脱硫率无明显变化.     

Combined atomic force microscopy and fluorescence correlation spectroscopy measurements to study the dynamical structure of interfacial fluids

We have studied the dynamic structure of thin (approximately a few nanometers) liquid films of a nearly spherical, nonpolar molecule tetrakis(2-ethylhexoxy)silane (TEHOS) by using a combination of atomic force microscopy (AFM) and fluorescence correlation spectroscopy (FCS). Ultra-sensitive interferometer-based AFM was used to determine the stiffness (force gradient) and the damping coefficient of the liquid film. The experiments show oscillations in the damping coefficient with a period of approximately 1 nm, which is consistent with the molecular dimension of TEHOS as well as previous X-ray reflectivity measurements. Additionally, we performed FCS experiments for direct determination of the molecular dynamics within the liquid film. From the fluctuation autocorrelation curve, we measured the translational diffusion of the probe molecule embedded within the fluid film formed on a solid substrate. The autocorrelation function was best fitted with two components, which indicate that the dynamics are heterogeneous in nature. However, the heterogeneity is not as pronounced as had been previously observed for molecularly thin liquid films sandwiched between two solid substrates.     

离子液体中卤素交换氟化合成七氟醚

在离子液体作为反应介质的条件下,以六氟异丙基氯甲基醚的氟代反应合成了七氟醚。 探讨了氟代反应机理,考察了[bpy]BF4、[bmim]BF4、[bepy]BF4、[bmim]PF6对反应产率的影响,研究了氟化剂、水和温度对反应产率的影响。 结果表明,以[bepy]BF4为反应介质,高比表面积的KF和微量的水有利于固态KF的部分离解进入有机相形成高活性的F-从而减少副产物,收率达到94.6%。 离子液体可重复使用3次以上,其活性没有明显下降。     

A Conjugated Copolymer Bearing Imidazolium-based Ionic Liquid:Electrochemical Synthesis and Electrochromic Properties

An imidazolium-based ionic liquid(IL) modified triphenylamine derivative,namely 1-(4-((4-(diphenylamino)benzoyl) oxy)butyl)-3-methyl imidazole tetrafluoroborate(TPAC_6 IL-BF_4),was designed and synthesized,and further applied with 3,4-ethylene dioxythiophene(EDOT)to prepare conjugated copolymer P(EDOT:TPAC_6 IL-BF_4) via electrochemical polymerization.The cyclic voltammetry curves show that the copolymer P(EDOT:TPAC_6 IL-BF_4) possesses two pairs of redox peaks,which should be ascribed to the redox behaviors of EDOT and triphenylamine.The ultraviolet-visible(UV-Vis) absorption spectrum of P(EDOT:TPAC_6 IL-BF_4) exhibits one maximum absorption peak at 580 nm and a small shoulder characteristic peak at 385 nm under neutral state which are assigned to π-π~* conjugated structure of EDOT and triphenylamine.After being applied at the positive voltage,the copolymer color changes from dark blue to light blue,which is close to the color of poly(3,4-ethylenedioxythiophene)(PEDOT).Surprisingly,the copolymer P(EDOT:TPAC_6 IL-BF_4) shows shorter switching time of 0.37 s,0.30 s at 580 nm and 0.38 s,0.45 s at 1100 nm compared with PEDOT.It is more intriguing that the copolymer P(EDOT:TPAC_6 IL-BF_4) exhibits electrochromism even in free supporting electrolyte.The results confirm that the existence of imidazolium-based ionic liquid has an improvement on the ion diffusion properties and the switching time of conjugated polymer,which may provide a potential direction for the preparation of high-performance electrochromic materials.     

Immobilization of Pd（Ⅱ）Catalysts for Cyclopropanation in Ionic Liquid

Cyclopropanation of styrene with ethyl diazoacetate catalyzed by Pd(Ⅱ） in ionic liquid [omim][BF4] was investigated.Palladium catalysts can be effectively immobilized in ionic liquid.The catalysts PdCl2 and cyclopalladated complex 2 contained in ionic liquid could be recycled for 6 and 7 times,respectively,without losing the efficiency.     

Predictions of cation and anion effects on solubilities,selectivities and permeabilities for CO2 in ionic liquid using COSMO based activity coefficient model

The solubilities and selectivities for CO₂, N₂ and CH₄ in ionic liquid were predicted using a COSMO based activity coefficient model, COSMO-SAC method. The 1-alkyl-3-methylimidazolium cations were focused in this work. The anion species include tetrafluoroborate [BF₄], hexafluorophosphate [PF₆], triflate [OTf], dicyanamide [dca] and bis(trifluoromethane)-sulfonimide [Tf₂N]. The predicted results of the solubilities of CO₂ in the ionic liquids by COSMO-SAC method are in agreement with the experimental data within the averaged deviation of 0.0017 in mole fraction. The predicted results of selectivities for CO₂/N₂ and CO₂/CH₄ represent the effects of anion species qualitatively. Permeability through supported liquid membrane can be presented by solubility and diffusion coefficients in the liquid. The permeabilities of CO₂ through the ionic liquid membranes were also predicted by a solution-diffusion model with COSMO-SAC method. The predicted results of the CO₂ permeabilities through the ionic liquids represent the experimental data within the order of the permeabilities.     

Na-K liquid alloy:A review on wettability enhancement and ionic carrier selection mechanism

The intrinsic liquid interface of Na-K alloy allays concerns about dendrite growth on metal anodes that are thermodynamically within the room temperature(20-22℃).Nevertheless,it hinders the formation of a stable electrode structure due to the inferior wettability induced by considerable liquid tension.In addition,the dominant ionic carrier in the Na-K alloy is subject to multiple factors,which is not conducive to customized battery design.This review,based on recently reported frontier achievements on Na-K liquid anodes,summarizes practical strategies for promoting the wettability by hightemperature induction,capillary effect,vacuum infiltration,and solid interface protection.Furthermo re,four selection mechanisms of the dominant ionic carrier are presented:(1) ion property dominated,(2)cathode dominated,(3) separator dominated,and(4) solid electrolyte interface dominated.Notably,initial electrolytes in energy storage systems have been unable to play a decisive role in ionic selection.Utilizing a superior wettability strategy and simultaneously identifying the dominant ionic carrier can facilitate the tailored application of dendrite-free Na-K liquid anodes.     

Poly(ethylene glycol)-lipase complexes that are highly active and enantioselective in ionic liquids

Lipase-catalyzed alcoholysis between vinyl acetate and 2-phenyl-1-propanol was investigated in dialkylimidazolium-based ionic liquids. Although native lipase powder exhibited very low activity in an ionic liquid, forming a poly(ethylene glycol)(PEG)-lipase complex improved the lipase activity in the ionic liquid. The activity of the PEG-lipase complex was higher in ionic liquids than in common organic solvents (n-hexane, isooctane and dimethylsulfoxide). Fluorescence measurements using 4-aminophthalimide revealed that the ionic liquids were more hydrophilic than the organic solvents used for non-aqueous enzymology. A kinetic study of lipase-catalyzed alcoholysis in an ionic liquid ([Bmim][PF6]) revealed that the Michaelis constant (Km) for 2-phenyl-1-propanol in the ionic liquid was half that in n-hexane, suggesting that the ionic liquid stabilized the enzyme-substrate complex. Finally, we carried out enantioselective alcoholysis of 1-phenylethanol in ionic liquids employing the PEG-lipase complex, and obtained high enantioselectivity, comparable to that in n-hexane.     

1-Butyl-2,3-trimethyleneimidazolium bis(trifluoromethylsulfonyl)imide ([b-3C-im][NTf2]): a new, stable ionic liquid

Using imidazole as the starting material, the synthesis of a new bicyclic ionic liquid [b-3C-im][NTf₂] is described. Except for the alkylation reaction in the second step (40% yield) of this four-step synthesis of [b-3C-im][NTf₂], others were all high yielding reactions (85-94% isolated yields). We investigated intrinsic reactivity of this and other imidazolium-based ionic liquids and found that, under strongly basic conditions (KOD in CD₃OD/D₂O (1:1) solution), the new ionic liquid was stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] and [bdmim][PF₆] ionic liquids were 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. At the same experimental condition, the most commonly employed [bmim][PF₆] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases (CD₃OD/D₂O = 1:1), only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and other ionic liquids gave no detectable exchanges even after one week at ambient temperature. It is therefore concluded that the new [b-3C-im][NTf₂] ionic liquid is far more chemically stable than previously reported [bmim][PF₆], [bdmim][NTf₂], and [bdmim][PF₆].     

呋喃类化合物在离子液体和硅胶负载离子液体中的Diels-Alder反应研

以1-丁基3-甲基咪唑盐作为离子液体阳离子,与三种不同阴离子BF4、PF6、Tf2N组成性质不同的三种离子液体,催化呋喃类和丁炔二羧酸酯之间发生的Diels-Alder反应,合成了一系列化合物,研究了离子液体的催化效果。研究表明,呋喃类化合物的极性越低, Diels-Alder 反应的活性越高。在含硫的呋喃类化合物的反应中,当以 [Bmim]PF6 作为离子液体时,Diels-Alder 反应的产率可达到53%。另外,当 [Bmim]PF6 离子液体被吸附在硅胶表面上时,Diels-Alder的反应产率有所提高。     

Nanoscale Pt(0) particles prepared in imidazolium room temperature ionic liquids: synthesis from an organometallic precursor,characterization, and catalytic properties in hydrogenation reactions

The reaction of Pt(2)(dba)(3) (dba = bis-dibenzylidene acetone) dispersed in room temperature 1-n-butyl-3-methylimidazolium (BMI) hexafluorophosphate ionic liquid with molecular hydrogen (4 atm) at 75 degrees C leads to stable and isolable nanometric Pt(0) particles. The X-ray diffraction analysis (XRD) of the material indicated that it is constituted of Pt(0). Transmission electron microscopy (TEM) analysis of the particles dispersed in the ionic liquid shows the formation of [Pt(0)](n) nanoparticles of 2.0-2.5 nm in diameter. A detailed examination of the nanoparticles imbibed in the ionic liquid and their environment shows an interaction of the BMI.PF(6) ionic liquid with the Pt(0) nanoparticles. The isolated [Pt(0)](n) nanoparticles can be redispersed in the ionic liquid or in acetone or used in solventless conditions for liquid-liquid biphasic, homogeneous, or heterogeneous hydrogenation of alkenes and arenes under mild reaction conditions (75 degrees C and 4 atm). The recovered platinum nanoparticles can be reused as a solid or redispersed in the ionic liquid several times without any significant loss in catalytic activity.     

毛细管电泳电致化学发光灵敏检测毒品类生物碱及在尿样分析中的应用

本文基于盐酸甲基麻黄碱、蒂巴因、磷酸可待因和乙酰可待因等4种分析物对三联吡啶钌电致化学发光具有增强作用的特性, 同时结合离子液体的使用, 提出了一种CE-ECL同时分离检测的新方法. 对电泳分离条件、电致化学发光检测条件和离子液体的影响进行了系统优化, 将提出的新方法成功应用于人尿样中4种毒品含量的分析, 结果令人满意.     

Ceric ammonium nitrate (CAN) as oxidizing or nitrating reagent for organic reactions in ionic liquids

The reaction of ceric ammonium nitrate, (NH₄)₂[Ce(NO₃)₆] or CAN, with naphthalene and 2-methylnaphthalene in the ionic liquid 1-ethyl-3-methylimidazolium triflate showed that the reaction products are strongly dependent on the water content of the ionic liquid and that cerium(IV) in the ionic liquid can electrochemically be regenerated.     

离子液体介质中钌纳米粒子催化苯乙酮及其衍生物的不对称加氢反应

采用水溶性三(间-磺酸钠苯基)膦(TPPTS)作稳定剂, 在离子液体1-丁基-3-甲基-咪唑四氟硼酸盐([BMIM]BF4)或1-丁基-3-甲基-咪唑对甲基苯磺酸盐([BMIM][p-CH3C6H4SO3])介质中用氢气还原RuCl3·3H2O, 得到钌纳米粒子. 将此钌纳米粒子与(1S, 2S)-1,2-二苯基乙二胺(简称(1S, 2S)-DPEN)、KOH在离子液体/异丙醇介质中原位生成一种不对称加氢催化剂, 用于催化苯乙酮及其衍生物的不对称加氢反应. 实验结果表明, 离子液体介质中的纳米钌催化剂体系具有良好的催化活性和对映选择性. 在优化反应条件下, 催化苯乙酮获得了100%的转化率和79.1%的对映选择性. 并且产物经正己烷萃取后, 含有钌纳米粒子的离子液体可以循环使用.