Synthesis and photovoltaic properties of phthalocyanine end-capped copolymers with conjugated dithienylbenzothiadiazole–vinylene side chains

Two phthalocyanine end-capped copolymers with conjugated dithienylbenzothiadiazole–vinylene side chains, PHY1 and PHY2, have been synthesized according to the Stille–Coupling polymerization method. The structures, thermostability, optical and electrochemical properties of the copolymers were characterized via NMR, GPC, TGA, DSC, UV–vis, photoluminescence (PL) spectroscopy, and cyclic voltammetry (CV), respectively. The two copolymers exhibit excellent film-forming ability and good thermostability in a wide temperature range. PHY1 and PHY2 end-capped with different phthalocyanines showed broad absorption bands ranging from the ultraviolet to the red/near-infrared (IR) region of the solar spectrum and deep HOMO energy levels. Bulk heterojunction polymer solar cells were fabricated based on PHY1 and PHY2 with [6,6]-phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM) as the electron acceptor and showed power conversion efficiencies (PCE) of 1.56% and 1.26%, respectively, under the illumination of AM 1.5, 100 mW/100 cm².     

Effect of oxadiazole side chains based on alternating fluorene-thiophene copolymers for photovoltaic cells

Three soluble alternating conjugated copolymers, comprised of 9,9-dihexylfluorene and thiophene derivatives with/without oxadiazole side chains, were synthesized via the palladium-catalyzed Suzuki coupling reaction. The structures of the polymers were confirmed with ¹H NMR and ¹³C NMR, and the effect of oxadiazole side chains on the thermal, optical, electrochemical and photovoltaic properties were investigated. The introduction of rigid oxadiazole side chains could benefit to improve thermal stabilities of the conjugated polymers. Cyclic voltammograms revealed that the LUMO energy levels of P2 and P3 were reduced in comparison with P1 due to the introduction of electron-deficient oxadiazole side chains, indicating that electron-injection and transporting properties have been improved. Photovoltaic cells (PVCs) were fabricated based on the blend of the as-synthesized copolymers and the fullerene acceptor [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) in a 1:1 weight ratio. The maximum power conversion efficiency (PCE = 1.49%) was obtained for P3 as the electron donor under the illumination of AM 1.5, 100 mW/cm².     

Synthesis and photovoltaic performances of 2,5-dioctyloxy-1,4-phenylenevinylene and terthiophene copolymers with di(p-tolyl)phenylamine and oxadiazole side groups

Three novel conjugated polymers (P1, P2, and P3), comprised of 2,5-dioctyloxy-1,4-phenylenevinylene and terthiophene derivatives with/without di(p-tolyl)phenylamine (TPAV) and oxadiazole (OXD) side groups, have been synthesized via the Witting-Horner reaction. The effect of TPAV and OXD side groups on the optical, electrochemical and photovoltaic properties has been investigated. It is found that the introduction of TPAV and OXD side groups to the backbone of P2 and P3 exhibits broader and stronger absorption than that of P1 without TPAV and OXD side groups. Photovoltaic cells have been fabricated with the as-synthesized polymers as the donors and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) as the acceptor in a 1:4 weight ratio. The device based on P2 shows a maximum power conversion efficiency of 1.75% under simulated AM 1.5 G solar irradiation (100 mW/cm²).     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of polymeric metal complexes containing 8-hydroxyquinoline as dye sensitizers for dye-sensitized solar cells

Four new donor–acceptor type polymeric metal complexes (P1, P2, P3, and P4) with the same Cd(II) complex in side chain and different conjugated backbone structures were synthesized by Yamamoto coupling and applied in dye-sensitized solar cells (DSSCs) as photosensitizers. The photophysical, electrochemical, and thermal properties were investigated in detail, showing that conjugated backbone containing fluorene improved intramolecular charge transfer and increased generation of photocurrent. The highest power conversion efficiency of 0.56% (J _sc?=?1.63?mA?cm^?2, V _oc?=?0.69?V, FF?=?0.50) was obtained with a DSSC based on P3 under simulated air mass 1.5 G solar irradiation, which shows a new strategy to design photosensitizers for DSSCs.     

Hydroformylation of oct-1-ene catalyzed by dinuclear gem-dithiolato-bridged rhodium(I) complexes and phosphorus donor ligands

The dinuclear gem-dithiolato bridged compounds [Rh₂(μ-S₂Cptn)(cod)₂] (1) (CptnS₂²⁻ = 1,1-cyclopentanedithiolato), [Rh₂(μ-S₂Chxn)(cod)₂] (2) (ChxnS₂²⁻ = 1,1-cyclohexanedithiolato), [Rh₂(μ-S₂CBn₂)(cod)₂] (3) (Bn₂CS₂²⁻ = 1,3-diphenyl-2,2-dithiolatopropane) and [Rh₂(μ-S₂CⁱPr₂)(cod)₂] (4) (ⁱPr₂CS₂²⁻ = 2,4-dimethyl-2,2-dithiolatopentane) dissolved in toluene in the presence of monodentate phosphine or phosphite P-donor ligands under carbon monoxide/hydrogen (1:1) atmosphere are efficient catalysts for the hydroformylation of oct-1-ene under mild conditions (6.8 atm of CO/H₂ and 80 °C). The influence of the gem-dithiolato ligand, the P-donor co-catalyst and the P/Rh ratio on the catalytic activity and selectivity has been explored. Aldehyde selectivities higher than 95% and turnover frequencies up to 245 h⁻¹ have been obtained using P(OMe)₃ as modifying ligand. Similar activity figures have been obtained using P(OPh)₃ although the selectivities are lower. Regioselectivities toward linear aldehyde are in the range 75–85%. The performance of the catalytic systems [Rh₂(μ-S₂CR₂)(CO)₂(PPh₃)₂]/PPh₃ has been found to be comparable to the systems [Rh₂(μ-S₂CR₂)(cod)₂] at the same P/Rh ratio. The system [Rh₂(μ-S₂CBn₂)(cod)₂] (3)/P(OPh)₃ has been tested in the hydroformylation-isomerization of trans-oct-2-ene. Under optimized conditions up to 54% nonanal was obtained. Spectroscopic studies under pressure (HPNMR and HPIR) evidenced the formation of hydrido mononuclear species under catalytic conditions that are most probably responsible for the observed catalytic activity.     

The d metal-sulfosalicylate complexes: Herring-bone, ladder and double-stranded chain frameworks with green luminescences

Assembly of 5-sulfosalicylic acid (H₃L) and d¹⁰ transition metal ions (Cd^II, Ag^I) with the neutral N-donor ligands produces five new complexes: [Cd₂(HL)₂(4,4′-bipy)₃]_n·2nH₂O (1), {[Cd₂(μ₂-HCO₂)₂(4,4′-bipy)₂(H₂O)₄][Cd(HL)₂(4,4′-bipy)(H₂O)₂]}_n (2), {[Cd(4,4′-bipy)(H₂O)₄][HL]·H₂O}_n (3), [Cd(HL)(dpp)₂(H₂O)]_n·4nH₂O (4), {[Ag(4,4′-bipy)][Hhbs]}_n (5) (4,4′-bipy=4,4′-bipyridine, dpp=1,3-di(pyridin-4-yl)propane, H₂hbs=4-hydroxybenzenesulfonic acid, the decarboxylation product of H₃L). Complex 1 adopts a 5-connected 3D bilayer topology. Complex 2 has the herring-bone and ladder chain, which are extended to a 3D network via hydrogen bonding. In 3–4 complexes, 3 is a 3D supermolecular structure formed by polymeric chains and 2D network of HL²⁻, while 4 gives the double-stranded chains. In 5, ladder arrays are stacked with the 2D networks of Hhbs⁻ anions in an –ABAB– sequence. Complexes 1–4 display green luminescences in solid state at room temperature, while emission spectra of 3 and 4 show obvious blue-shifts at low temperature.     

Developing Wide Bandgap Polymers Based on Sole Benzodithiophene Units for Efficient Polymer Solar Cells

In this work, a series of sole benzodithiophene-based wide band gap polymer donors, namely PBDTT, PBDTS, PBDTF and PBDTCl, were developed for efficient polymer solar cells (PSCs) by varying the heteroatoms into the conjugated side chains. The effects of sulfuration, fluorination and chlorination were also investigated systematically on the overall properties of these BDT-based polymers. The HOMO levels could be lowered gradually by introducing sulfur, fluorine and chlorine atoms into the side chains, which contributed to the stepwise increased V_oc (from 0.78 V to 0.84 V) in the related PSCs using Y6 as the electron acceptor. This side-chain engineering strategy could promote the polymer chain interactions and fine-tune the phase separation of active blends, leading to enhanced absorption, ordered molecular packing and crystallinity. Among them, the chlorinated PBDTCl exhibited not only high level absorption and crystallinity, but also the most balanced hole/electron charge transport and the most optimized morphology, giving rise to the best PCE of 13.46 % with a V_oc of 0.84 V, a J_sc of 23.16 mA cm⁻² and an FF of 69.2 %. The chlorination strategy afforded PBDTCl synthetic simplicity but high efficiency, showing its promising photovoltaic applications for realizing low-cost practical PSCs in near future.     

Side‐Chain Engineering of Benzodithiophene‐Fluorinated Quinoxaline Low‐Band‐Gap Co‐polymers for High‐Performance Polymer Solar Cells

A new series of donor–acceptor co‐polymers based on benzodithiophene and quinoxaline with various side chains have been developed for polymer solar cells. The effect of the degree of branching and dimensionality of the side chains were systematically investigated on the thermal stability, optical absorption, energy levels, molecular packing, and photovoltaic performance of the resulting co‐polymers. The results indicated that the linear and 2D conjugated side chains improved the thermal stabilities and optical absorptions. The introduction of alkylthienyl side chains could efficiently lower the energy levels compared with the alkoxyl‐substituted analogues, and the branched alkoxyl side chains could deepen the HOMO levels relative to the linear alkoxyl chains. The branched alkoxyl groups induced better lamellar‐like ordering, but poorer face‐to‐face packing behavior. The 2D conjugated side chains had a negative influence on the crystalline properties of the co‐polymers. The performance of the devices indicated that the branched alkoxyl side chains improved the V_oc, but decreased the J_sc and fill factor (FF). However, the 2D conjugated side chains would increase the V_oc, J_sc, and FF simultaneously. For the first time, our work provides insight into molecular design strategies through side‐chain engineering to achieve efficient polymer solar cells by considering both the degree of branching and dimensionality.     

Novel conjugated copolymers based on dithiafulvalene moiety for bulk heterojunction solar cells

New conjugated copolymers, P1‐P3 , based on dithiafulvalene‐fused entity and different conjugated segments have been synthesized. Incorporation of electron‐deficient conjugated segments into the conjugated copolymers results in red shifting the absorption band and lowering the hole mobility. Bulk heterojunction solar cells using on these polymers as the donor and [6,6]‐phenyl‐C61 ‐butyric acid methyl ester (PC₆₁BM) as the acceptor were fabricated by solution process. The cells based on the blend of P1‐P3 /PC₆₁BM (1:1, w/w) have power conversion efficiencies (PCEs) ranging from 0.53 to 0.93%. Among these, the cell of P1 /PC₆₁BM exhibited the highest open‐circuit voltage at 0.85 V, and the cell of P3/PC₆₁BM exhibited the best PCE at 0.93% with the short‐circuit current (J_SC) of 4.88 mA/cm². © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis, characterization and photovoltaic properties of a low-bandgap platinum(II) polyyne functionalized with a 3,4-ethylenedioxythiophene-benzothiadiazole hybrid spacer

The synthesis, characterization and optical spectroscopy of a deep blue platinum(II) polyyne functionalized with the (3,4-ethylenedioxythiophene)-benzothiadiazole hybrid spacer (P1) and its dinuclear platinum molecular model complex (M1) are described. This metalated polymer P1 exhibits good thermal stability and possesses a narrow bandgap of 1.76 eV. Optical spectroscopic measurements of these materials reveal a substantial donor-acceptor interaction along the rigid backbone of the organometallic polyynes through the interaction of metal center and the conjugated tricyclic ligand. Preliminary study shows that P1: methanofullerene acceptor blend can be used as an active layer of bulk-heterojunction polymer solar cells. Photoexcitation of this blend layer in some yet-to-be optimized cells results in a photo-induced electron transfer from the π-conjugated metallopolyyne electron donor to [6,6]-phenyl C₆₁-butyric acid methyl ester with a power conversion efficiency (PCE) close to 0.30% under air mass (AM1.5) simulated solar illumination. The power dependencies of the solar cell parameters (including the short-circuit current density, open-circuit voltage, fill-factor and PCE) were also studied.     

New bifunctional N-thiophosphorylated thiourea and 2,5-dithiobiurea derivatives. Crystal structures of R[C(S)NHP(S)(OiPr)2]2 (R = –N(Ph)CH2CH2N(Ph)– and –NHNH–)

A new bifunctional N-thiophosphorylated thiourea and 2,5-dithiobiurea of the common formula R[C(S)NHP(S)(OiPr)₂]₂ [R = –N(Ph)CH₂CH₂N(Ph)– (H₂L^a); –NHNH– (H₂L^b)] have been synthesized and characterized by IR, ¹H, ³¹P spectroscopy and the single crystal X-ray diffraction method. The structure of the latter compound in CDCl₃ and acetone-d₆ solutions has been discussed in comparison with the monofunctional thiosemicarbazide PhNHNHC(S)NHP(S)(OiPr)₂ (HL^c).     

Synthesis and applications of 2,7‐carbazole‐based conjugated main‐chain copolymers containing electron deficient bithiazole units for organic solar cells

A series of low‐band‐gap (LBG) donor–accepor conjugated main‐chain copolymers ( P1 – P4 ) containing planar 2,7‐carbazole as electron donors and bithiazole units (4,4′‐dihexyl‐2,2′‐bithiazole and 4,4′‐dihexyl‐5,5′‐di(thiophen‐2‐yl)‐2,2′‐bithiazole) as electron acceptors were synthesized and studied for the applications in bulk heterojunction (BHJ) solar cells. The effects of electron deficient bithiazole units on the thermal, optical, electrochemical, and photovoltaic (PV) properties of these LBG copolymers were investigated. Absorption spectra revealed that polymers P1 – P4 exhibited broad absorption bands in UV and visible regions from 300 to 600 nm with optical band gaps in the range of 1.93–1.99 eV, which overlapped with the major region of the solar emission spectrum. Moreover, carbazole‐based polymers P1 – P4 showed low values of the highest occupied molecular orbital (HOMO) levels, which provided good air stability and high open circuit voltages (V_oc) in the PV applications. The BHJ PV devices were fabricated using polymers P1 – P4 as electron donors and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or (6,6)‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as electron acceptors in different weight ratios. The PV device bearing an active layer of polymer blend P4:PC₇₁BM (1:1.5 w/w) showed the best power conversion efficiency value of 1.01% with a short circuit current density (J_sc) of 4.83 mA/cm², a fill factor (FF) of 35%, and V_oc = 0.60 V under 100 mW/cm² of AM 1.5 white‐light illumination. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and Photovoltaic Properties of Two‐Dimensional Low‐Bandgap Copolymers Based on New Benzothiadiazole Derivatives with Different Conjugated Arylvinylene Side Chains

A new series of 2,1,3‐benzothiadiazole (BT) acceptors with different conjugated aryl‐vinylene side chains have been designed and used to build efficient low‐bandgap (LBG) photovoltaic copolymers. Based on benzo[1,2‐b:3,4‐b′]dithiophene and the resulting new BT derivatives, three two‐dimensional (2D)‐like donor (D)–acceptor (A) conjugated copolymers have been synthesised by Stille coupling polymerisation. These copolymers were characterised by NMR spectroscopy, gel‐permeation chromatography, thermogravimetric analysis and differential scanning calorimetry. UV/Vis absorption and cyclic voltammetry measurements indicated that their optical and electrochemical properties can be facilely modified by changing the structures of the conjugated aryl‐vinylene side chains. The copolymer with phenyl‐vinylene side chains exhibited the best light harvesting and smallest bandgap of the three copolymers. The basic electronic structures of D–A model compounds of these copolymers were also studied by DFT calculations at the B3LYP/6‐31G* level of theory. Polymer solar cells (PSCs) with a typical structure of indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/copolymer:[6,6]‐phenyl‐C₆₁(C₇₁)‐butyric acid‐methyl ester (PCBM)/calcium (Ca)/aluminum (Al) were fabricated and measured under the illumination of AM1.5G at 100 mW cm^?2. The results showed that the device based on the copolymer with phenyl‐vinylene side chains had the highest efficiency of 2.17 % with PC₇₁BM as acceptor. The results presented herein indicate that all the prepared copolymers are promising candidates for roll‐to‐roll manufacturing of efficient PSCs. Suitable electronic, optical and photovoltaic properties of BT‐based copolymers can also be achieved by fine‐tuning the structures of the aryl‐vinylene side chains for photovoltaic application.     

Study on structural properties and solution dynamics of zinc complexes with the (N,N-dimethylaminomethyl)ferrocenyl ligand

The reaction of {C,N-[Fe(η⁵-C₅H₅)(η⁵-C₅H₃(CH₂NMe₂)-2)]}Li, (FcN)Li, with zinc chloride affords the diorganozinc complex (FcN)₂Zn (1). In solution, 1 appears as a mixture of rac and meso diastereomers, whereas in the solid state it crystallizes solely as a rac diastereomer. The ratio of rac/meso diastereomers in solution is solvent-, temperature- and concentration-dependent, consistent with an intermolecular exchange between diastereomers. An intramolecular dynamic phenomenon involving dissociation and recoordination of Zn---N bonds was also observed. The reaction of 1 with zinc chloride yields the monoorganozinc compound (FcN)ZnCl (2) as a slightly soluble yellow microcrystalline powder.     

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

Donor–acceptor (D–A) conjugated copolymers are one of known classes of organic optoelectronic materials and have been well developed. However, less attention has been paid on acceptor–acceptor (A–A) conjugated analogs. In this work, two types of A–A conjugated copolymers, namely P1‐Cn and P2‐Cn (n is the carbon number of their alkyl side chains), were designed and synthesized based on perylenediimide ( PDI ) and 2,1,3‐benzothiadiazole ( BT ). Different from P1‐Cn , P2‐Cn polymers have additional acetylene π‐spacers between PDI and BT and thus hold a more planar backbone configuration. Property studies revealed that P2‐Cn polymers possess a much red‐extended UV–vis absorption spectrum, stronger π–π interchain interactions, and one‐order larger electron mobility in their neat film state than P1‐Cn . However, all‐polymer solar cells using P1‐Cn as acceptor component and poly(3‐hexyl thiophene) or poly(2,7‐(9,9‐didodecyl‐fluoene)‐alt?5,5′‐(4,7‐dithienyl‐2‐yl‐2,1,3‐benzothiadiazole) as donor component exhibited much better performance than those based on P2‐Cn . Apart from their backbone chemical structure, the side chains were found to have little influence on the photophysical, electrochemical, and photovoltaic properties for both P1‐Cn and P2‐Cn polymers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1200–1215     

Role of ligand conformation in the structural diversity of copper(II) and silver(I) coordination polymers containing the angular dipyridyl ligand bearing amide spacer

The new dipyridyl ligands N,N′-(methylenedi-p-phenylene)bis(pyridine-4-carboxamide), L1, and N,N′-(methylenedi-p-phenylene)bis(pyridine-3-carboxamide), L2, incorporating amide spacers have been synthesized and reacted with metal salts to give complexes of the types [Cu(L1)₂X₂]_∞ (X = Cl, 1 and X = Br, 2), {[Cu(L1)₂(DMF)](NO₃)₂}_∞, 3, {[Ag₂(L1)₂](SO₄)}_∞, 4, and {[Cu(L2)(DMSO)₂(NO₃)](NO₃)}_∞, 5. All compounds have been characterized by spectroscopic methods and their structures determined by X-ray crystallography.Complexes 1, 2 and 3 form 1-D double-stranded polymeric chains showing rhombic molecular squares with approximate dimensions of 16.95 × 19.13 Å² for 1, 17.03 × 19.06 Å² for 2 and 16.66 × 19.94 Å² for 3. Complex 4 forms infinite 1-D zigzag polymeric chains, which are interlinked through a series of Ag–O interactions to form wavy 1-D ladder like chains, and complex 5 forms 1-D sinusoidal chains. While the L1 ligands in complexes 1, 2 and 3 adopt the cis conformation and that in complex 4 adopts trans conformation, the L2 ligand in complex 5 adopts the trans-anti conformation. The ligand conformations also differ in the dihedral angles between the pyridyl and phenyl rings. All complexes exhibit emissions which may be tentatively assigned as intraligand (IL) π → π* transition.     

Conformational Relaxation of p‐Phenylenevinylene Trimers in Solution Studied by Picosecond Time‐Resolved Fluorescence

Two p‐phenylenevinylene (PV) trimers, containing 3′‐methylbutyloxyl (in MBOPV3) and 2′‐ethylhexyloxyl (in EHOPV3) side chains, are used as model compounds of PV‐based conjugated polymers (PPV) with the purpose of clarifying the origin of fast (picosecond time) components observed in the fluorescence decays of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV). The fluorescence decays of MBOPV3 and EHOPV3 reveal the presence of similar fast components, which are assigned to excited‐state conformational relaxation of the initial population of non‐planar trimer conformers to lower‐energy, more planar conformers. The rate constant of conformational relaxation k_CR is dependent on solvent viscosity and temperature, according to the empirical relationship k_CR=aη_o^?α?exp(?αE_η/RT), where aη_o^?α is the frequency factor, η_o is the pre‐exponential coefficient of viscosity, E_η is the activation energy of viscous flow. The empirical parameter α, relating the solvent microscopic friction involved in the conformational change to the macroscopic solvent friction (α=1), depends on the side chain. The fast component in the fluorescence decays of MEH‐PPV polymers (PPVs), is assigned to resonance energy transfer from short to longer polymer segments. The present results call for revising this assignment/interpretation to account for the occurrence of conformational relaxation, concurrently with energy transfer, in PPVs.