脲衍生物型手性固定相分离α－氨基酸对映体的研究

 利用脲衍生物型手性色谱柱，作正相和反相液相色谱拆分Ｎ－３，５－二硝基苯甲酰化氨基酸丁酯衍生物。结果表明，正相色谱的手性分离效果比反相色谱要好得多，并且手性洗脱顺序完全相反。认为在固定相上对拆分起主要作用的可能是（Ｒ）－１－（α－萘基）乙胺部分的手性碳原子，而另外一个手性碳原子在拆分过程中起辅助作用。流动相在拆分过程中起着很重要的作用。     

脲衍生物型手性固定相分离α－氨基酸对映体的研究

利用脲衍生物型手性色谱柱，作正相和反相液相色谱拆分Ｎ－３，５－二硝基苯甲酰化氨基酸丁酯衍生物。结果表明，正相色谱的手性分离效果比反相色谱要好得多，并且手性洗脱顺序完全相反。认为在固定相上对拆分起主要作用的可能是（Ｒ）－１－（α－萘基）乙胺部分的手性碳原子，而另外一个手性碳原子在拆分过程中起辅助作用。流动相在拆分过程中起着很重要的作用。     

反相键合相高效液相色谱法分离测定萘普生

建立了分离测定萘普生和溴代萘普生的反相键合相高效液相色谱法。采用ＯＤＳ柱，以添加５０ｍｍｏｌ／Ｌ乳酸并用高氯酸调节ｐＨ为２．５的８０％甲醇－水溶液作为流动相，以苯甲酸为内标物，测定了不对称合成工艺产物中萘普生和溴代萘普生的含量。方法的准确度分别为９９．８３％～１０２．０７％（萘普生）和９９．０％～１００．８３％（溴代萘普生），相对标准偏差分别小于２．５８％（萘普生）和３．６４％（溴代萘普生）。方法可用于工艺条件的选择和质量检测。     

反相键合相高效液相色谱法分离测定萘普生

 建立了分离测定萘普生和溴代萘普生的反相键合相高效液相色谱法。采用ＯＤＳ柱，以添加５０ｍｍｏｌ／Ｌ乳酸并用高氯酸调节ｐＨ为２．５的８０％甲醇－水溶液作为流动相，以苯甲酸为内标物，测定了不对称合成工艺产物中萘普生和溴代萘普生的含量。方法的准确度分别为９９．８３％～１０２．０７％（萘普生）和９９．０％～１００．８３％（溴代萘普生），相对标准偏差分别小于２．５８％（萘普生）和３．６４％（溴代萘普生）。方法可用于工艺条件的选择和质量检测。     

反相高效液相色谱法分离铂族金属及其伴生元素

本文报道以２－（６－甲基－２－苯并噻唑偶氮）－５－二乙氨基酚作柱前衍生试剂，以甲醇／水＝８２／１８（Ｖ／Ｖ），含１０ｍｍｏｌ／ＬｐＨ５．０醋酸盐缓冲溶液，１０ｍｍｏｌ／Ｌ水杨酸钠，５ｍｍｏｌ／ＬＴＢＡ．Ｂｒ作流动相，反相高效液相色谱法定量分离测定Ｒｕ（Ⅲ），Ｒｈ（Ⅲ）、Ｐｄ（Ⅱ）、Ｏｓ（Ⅳ）、Ｉｒ（Ⅳ）、Ｐｔ（Ⅱ）、Ｃｏ（Ⅱ）、Ｎｉ（Ⅱ）和Ｃｕ（Ⅱ）。当Ｓ／Ｎ＝３时，各金属离子的检出限分别为（ｎｍ     

柱前衍生反相高效液相色谱分离和测定氨基酸：用N—羟基琥珀酰？…

以Ｎ－羟基琥珀酰亚胺－α－萘乙酸酯（ＳＩＮＡ）为氨基酸的柱前衍生试剂,反相高效液相色谱分离测定了１５种氨基酸。采用含１０ｍｍｏｌ／Ｌ ｐＨ５．０的乙酸－乙酸钠缓冲溶液的甲醇－乙酸乙酯－水（１０／２／８８,Ｖ／Ｖ／Ｖ）溶液为流动相体系。分离测定了７种氨基酸;用甲醇－乙酸乙酯－水（２６／２／７７,Ｖ／Ｖ／Ｖ）分离测定了５种氨基酸;用甲醇－乙酸乙酯－水（４５／２／５３,Ｖ／Ｖ／Ｖ）分离测定了３种氨基酸。     

由SRN1反应生成的三种取代苯并咪唑的薄层定量研究

研究了光诱导自由基链式亲核取代（ＳＲＮＩ）反应生成Ｎ－（α－萘基）苯并咪唑，Ｎ－（β－萘基）苯并咪唑和Ｎ－（α－吡啶基）苯并咪唑的薄层光密度定量方法，并成功地应用于其反应机理的研究，该法简便，快速，准确，线性范围０～３．０μｇ平均回收率９９．８％～１００．５％相对标准偏差〈４．７％。     

薄层光密度法测定低含量的N—（α—萘基）咔唑和N—（β—萘基）咔唑

测定了光诱导ＳＲＮ１反应生成的Ｎ－（α－萘基）咔唑和Ｎ－（β－萘基）。光化学反应产物用硅胶板展开，外标法定量，测定波长２８８ｎｍ斑点的线性范围０～２μｇ，回收率１００．５％，相对标准偏差４．８％，Ｎ－（α－萘基）咔唑含量＜１％，Ｎ－（β－萘基）咔唑含量２．２６％。     

反相离子对色谱法—电化学检测测定亚硝酸根,硫氰酸根,苯胺

本文采用反相离子对色谱法（安培检测）对影响ＮＯ＾－２、ＳＣＮ＾－、Ｃ６Ｈ５ＮＨ２容量因子的各因素进行了研究，建立了分离测定这三种组分的最佳色谱条件。方法快速、灵敏、选择性高。     

含苯氧基萘并萘醌和偶氮苯双变色基化合物的合成和性质

通过６－氯－５，１２－萘并萘醌与４－羟基偶氮苯及其衍生物的反应合成了３种含苯氧基萘并萘醌和偶氮苯光致变色基的双变色基化合物，６－［４－（苯偶氮基）苯氧基］－５，１２－萘并萘醌（５），６－［４－（ｐ－乙氧基苯偶氮基）苯氧基］－５，１２－萘并萘醌（６）和６－［４－（ｐ－硝基苯偶氮基）苯氧基］－５，１２－萘并萘醌（７）．这些化合物的苯氧基萘并萘醌变色基的ＵＶ诱导光致变色性较弱；基于氨与苯氧基萘并萘醌ａｎａ显色体的不可逆反应，化合物５和６ＤＭＳＯ溶液在３６５ｎｍ紫外光辐照光稳态（ＰＳＳ）下的ａｎａ醌式摩尔分数估计分别为２２％和１７％．这些结果说明，苯偶氮基对苯氧基萘并萘醌变色基的光致变色性质有着极强的影响．另一方面，与４－羟基偶氮苯母体不同，这些双变色基化合物在ＤＭＳＯ中偶氮苯变色基的顺式异构体是相对稳定的     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。