Investigation on poly[(methylsilylene ethynylene phenylene ethynylene)-co-(tetramethyldisiloxane ethynylene phenylene ethynylene)]

<正>Poly[(methylsilylene ethynylene phenylene ethynylene)-co-(tetramethyldisiloxane ethynylene phenylene ethynylene)]was synthesized by polycondensation reaction of m-diethynylbenzene magnesium reagent with 1,3-dichlorotetramethyldisiloxane and dichloromethylsilane.The copolymer was characterized by FT-IR,~1H NMR,differential scanning calorimetry and thermogravimetric analysis.The results show that the copolymer exhibits good processability and cures at low temperatures.The cured copolymer shows high thermal stability.     

Photo and Thermal Cured Silicon‐Containing Diethynylbenzene Fibers via Melt Electrospinning with Enhanced Thermal Stability

An inorganic–organic hybrid material, poly(dimethylsilylene ethynylenephenyleneethynylene) (PMSEPE), was synthesized in a mild condition and its microfiber was successfully produced by melt electrospinning. The electrospinning parameters, which affected the morphology and diameter of fibers, were well investigated. To maintain the fiber structure at thermal cured temperature (above melting point), the PMSEPE fibers were enhanced via thiol‐yne photo polymerization. Followed by the thermal curing reaction, the heat‐resistance and mechanical properties of fibers were enhanced. The mechanism of two‐step curing was explored and confirmed by means of Fourier transform infrared, differential scanning calorimetry, and X‐ray photoelectron spectroscopy (XPS). Thermaogravimetric analysis and scanning electron microscopy results show that after carbonization at 800 °C, the two‐step cured fibers had only a small weight loss (20%) and the fibers can still maintain the original morphology. Moreover, the two‐step cured fiber exhibited a high tensile strength (55.4 MPa) and a small elongation at break (0.02%). All the results indicate that the fibers could be applied as fiber‐reinforced materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2815–2823     

Dynamic mechanical properties of extruded rods of poly(dimethylsilylene‐co‐methyl‐n‐propylsilylene)

Tractable polysilanes were prepared by the copolymerization of a methyl‐n‐propylsilylene (MP) unit into poly(dimethylsilylene), which neither dissolves in common solvents nor melts before decomposition. Although poly(dimethylsilylene‐co‐methyl‐n‐propylsilylene) has poor solubility in the composition range of the dimethylsilylene (DM) unit to the MP unit (DM/MP = 7/3 ∼ 9/1), the copolymers form the columnar mesophase at elevated temperatures. Highly oriented rods were prepared via the extrusion of the copolymers with a circular tube die in a temperature range in which the transition to the columnar mesophase began to occur (70°C when DM/MP = 7/3 and 8/2 and 120°C when DM/MP = 9/1). The extruded rods were characterized in detail by dynamic viscoelasticity and wide‐angle X‐ray diffraction (WAXD) to clarify the structure–mechanical‐property relationship. The orientation functions of the extruded rods were determined by the azimuthal intensity distribution of the WAXD reflection. The orientation function and dynamic storage modulus increased with an increasing extrusion ratio. The dynamic storage modulus at −150°C was 8 ∼ 10 GPa at the highest extrusion ratio and correlated well with the crystal orientation function. The dynamic storage modulus at room temperature was lowered by the structural relaxations at −100 ∼ +30°C, which corresponded to the molecular motion of the rigid molecular chains of the copolymer and the local molecular motion of the MP unit. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 698–706, 2000     

Organosilane polymers: Formable copolymers containing dimethylsilylene units

Formable silane copolymers that contain dimethylsilylene units were synthesized and characterized. These polymers have high molecular weights and appreciable solubility in common solvents, can be molded or cast into films or drawn into fibers, and are photoactive.     

Synthesis and properties of new Si?H-containing polymers

Poly[(methylsilylene)ethynylene] ( 1 ) and poly[2,5-thiophenediyl(methylsilylene)] ( 2 ) are prepared in good yields. Thermogravimetric analysis and differential scanning calorimetry indicate the Si H group to increase the pyrolysis residue yields. Gelation was achieved from polymer 1 to get improved preceramic materials. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2275–2282, 1998     

Organosilane polymers: Formable polymers containing methylsilylene units

Organosilane polymers containing methylsilylene units were prepared by sodium condensation of MeHSiCl₂ alone or with R¹R²SiCl₂ (R¹ and R² = alkyl, aryl, or aralkyl) in a blend of toluene and dioxane followed by fast filtration under N₂. These polymers are readily soluble in common solvents and can be drawn into fibers or formed into films by molding, casting, or potting. They can be crosslinked by oxidation, irradiation, or hydrosilylation of vinylsilane in the presence of platinum complexes. The effect of the quantity of MeHSiCl₂ on molecular weights of copolymers was also discussed.     

Si/C Phases from the IR Laser-induced Decomposition of Silacyclobutane and 1,3-Disilacyclobutane

CO₂ laser-induced infrared multiphoton decomposition (IRMPD) and SF₆ photosensitized decomposition (LPD) of silacyclobutane (SCB) and 1,3-disilacyclobutane (DSCB) in the gas phase results in the very efficient deposition of Si/C/H and SiC materials, and it is inferred that the process is dominated by formation of transient silene; silene rearrangement to methylsilylene; silene and methylsilylene dehydrogenation; and polymerization of SiCH_n (n < 4) species. The deposits are sensitive to oxygen. Decomposition and SiC formation are favoured with IRMPD experiments conducted with high-energy fluxes. The laser technique is promising for low-temperature chemical vapour deposition of amorphous SiC.     

4,4'-双甲基丙烯酰氧基二苯砜的制备及其共聚透明树脂的性能

４，４－双甲基丙烯酰氧基二苯砜的制备及其共聚透明树脂的性能高长有＊ａ杨柏ｂ尹作为ｂ宋海清ａ沈家骢ｂ（ａ浙江大学高分子系杭州３１００２７；ｂ吉林大学化学系长春）关键词双甲基丙烯酰氧基二苯砜，制备，透明树脂，性能１９９６－１２－３１收稿，１９９７－０７...     

Ketene organoelement derivatives. Synthesis of bis(l-R-2-oxovinyl)silanes and germanes (R = SiMe3, GeMe3, SnMe3)

Earlier unknown 1,3-bisketene organoelement derivatives RMeE(C(E ’Me₃)=C=O)₂ (E = Si, Ge; E’ = Si, Ge, Sn) have been synthesized by the reaction of bis(alkoxyethynyl)silanes and -germanes with Me₃E’Hal. Bis(1-trimethylsilyl-2-oxovinyl)silane is also formed by the reaction of trimethylsilyl- and (dimethylsilylene)bisketenes with dimethylsilylene bistriflate and trimethylsilyl triflate, respectively. Addition of nucleophiles to the ketene fragment of compounds synthesized has been studied.     

{1,1′‐(Dimethylsilylene)bis[methanechalcogenolato]}diiron Complexes [2Fe2E(Si)] (E=S,Se, Te) – [FeFe] Hydrogenase Models

(Bis‐selenolato) and (bis‐tellurolato)diiron complexes [2Fe2E(Si)] were prepared and compared with the known (bis‐thiolato)diiron complex A to assess their ability to produce hydrogen from protons. Treatment of [Fe₃(CO)₁₂] with 4,4‐dimethyl‐1,2,4‐diselenasilolane ( 1 ) in boiling toluene afforded hexacarbonyl{μ‐{[1,1′‐(dimethylsilylene)bis[methaneselenolato‐κSe : κSe]](2 ?)}}diiron(Fe? Fe) ( 2 ). The analog bis‐tellurolato complex hexacarbonyl{μ‐{[1,1′‐(dimethylsilylene)bis[methanetellurolato‐κTe : κTe]](2 ?)}}diiron(Fe? Fe) ( 3 ) was obtained by treatment of [Fe₃(CO)₁₂] with dimethylbis(tellurocyanatomethyl)dimethylsilane, which was prepared in situ. All compounds were characterized by NMR, IR spectroscopy, mass spectrometry, elemental analysis and single‐crystal X‐ray analysis. The electrocatalytic properties of the [2Fe2X(Si)] (X=S, Se, Te) model complexes A, 1 , and 2 towards hydrogen formation were evaluated.     

Organosilane polymers. I. Poly(dimethylsilylene)

Poly(dimethylsilylene) higher polymers prepared by alkali metal coupling of purified dimethyldichlorosilane were found to be high melting, largely crystalline polymers, soluble in solvents at temperatures above 200°C.     

Copolymerization of ethylene with cycloolefins or cyclodiolefins by a constrained‐geometry catalyst

The copolymerization of ethylene and cycloolefins [cyclopentene (CPE), cyclohexene (CHX), cycloheptene (CHP), cyclooctene (COT), cyclododecene (CDO), norbornene (NB), and 5,6‐dihydrodicyclopentadiene HDCPD] and cyclodiolefins [1,3‐cyclopentadiene (CPD), 1,4‐cyclohexadiene (CHD), 1,5‐cyclooctadiene (COD), 2,5‐norbornadiene (NBD), and dicyclopentadiene (DCPD)] was investigated with a constrained‐geometry catalyst, dimethylsilylene(tetramethylcyclopentadienyl)(N‐tert‐butyl)titanium dichloride, with methyl isobutyl aluminoxane as a cocatalyst. In the copolymerization with cycloolefins, the olefins, except for CHX, CDO, and HDCPD, were copolymerized via the 1,2‐insertion mode with the following reactivity: NB > CHP > COT > CPE. In the copolymerization with cyclodiolefins, corresponding copolymers, except for copolymerization with CHD, were obtained. A crosslinking fraction was detected in the copolymers with COD and NBD. The reactivity of the cyclodiolefins, except for COD, was higher than that of the cycloolefins. CPD was copolymerized via 1,2‐insertion, 1,4‐insertion or 1,2‐insertion of dimerized DCPD. The copolymerization with COD showed peculiar behavior under the copolymerization condition of a high COD concentration in the feed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1285–1291, 2005     

Preparation and structural determination of siloxane-modified sulfone-containing epoxy resins

Siloxane-modified sulfone-containing epoxy resins (ESBS) were prepared by polycondensation of PMPS and/or PDMS siloxane oligomers with EBS, the sulfone-containing epoxy resin. Structures were analyzed by IR, ¹H-, and ¹³C-NMR. The siloxane content in the copolymers was determined by ¹H-NMR with an integration technique. Epoxy equivalent weight (EEW) determination indicated that the oxirane ring of EBS was intact with this hot-melt procedure. The GPC measurement of these ESBS copolymers showed that molecular weight (MW) increased with increasing siloxane content in PMPS-modified copolymers. Evidence of siloxane incorporation in the copolymer was discussed. © 1996 John Wiley & Sons, Inc.     

Generation of dimethylsilylene and allylidene holmium complexes from trimethylsilylated allyl ligands

The reaction of K[1,3-(SiMe3)2C3H3] with partially hydrated holmium triflate leads to a dimeric complex (1) in which hydrogen abstraction from a trimethylsilyl group has occurred on two allyl ligands, forming dimethylsilylene units that bridge the holmium atoms. When the reaction time is prolonged, a different product (2) is isolated, in which in addition to two dimethylsilylene bridges, the metal centers are joined with a mu-eta1,eta3-allylidene ligand. Both crystallographic and computational studies provide evidence for delocalized bonding in the allylidene fragment.     

Effect of micelle structure on the spectral properties of poly(dimethylsilylene)

The absorption and fluorescence spectral features of an intractable poly(silylene), poly(dimethylsilylene) (1), in aqueous micelles--attributable to an elongated transoid backbone conformation encompassed by three micelles--are discussed.     

Microwave Synthesis of Copolymers Based on Itaconic Acid Moiety and Their Utility for Scavenging of Copper (II) and Lead (II)

We report here the preparation of the two copolymers, itaconic acid-methyl methacrylate and itaconic acid-acrylamide, in different ratios using microwave irradiation in the presence of azobisisobutyronitrile (AIBN) as initiator and 2-butanone as a solvent. All the prepared copolymers were characterized by different techniques; FT-IR, thermal analysis and elemental microanalysis. The thermal stability property of the prepared copolymers correlated with the changing of the itaconic acid ratio, as the ratio of itaconic acid increased, the crystallinity of the copolymer decreases. The itaconic acid-based copolymers also showed a good scavenging behavior in alkaline media for Cu (II) and Pb (II). The chelation behavior of both Cu (II) and Pb (II) complexes were checked using FT-IR, thermogravimetric analysis (TGA), and differential scanning calorimetery (DSC).     

In situ diagnostics of the decomposition of silacyclobutane on a hot filament by vacuum ultraviolet laser ionization mass spectrometry

The gas-phase reaction products of silacyclobutane (SCB) and 1, 1-dideuterio-silacyclobutane (SCB-d(2)) from a hot-wire chemical vapor deposition (HWCVD) chamber were diagnosed in situ using vacuum ultraviolet (VUV) laser single-photon ionization (SPI) coupled with time-of-flight (TOF) mass spectrometry. The SCB molecule was found to decompose at a filament temperature as low as 900 degrees C. Both Si- (silylene, methylsilylene, and silene) and C-containing (ethene and propene) species were produced from the SCB decomposition on the filament. Ethene and propene were detected by the mass spectrometer. It is demonstrated that the formation of ethene is favored over that of propene. The experimental study of hot-wire decomposition of SCB-d(2) shows that propene is most likely produced by a process that is initiated by a 1,2-H(D) migration to form n-propylsilylene, followed by an equilibration with silacyclopropane, which then decomposes to propene. The detection of ethene in our experiment indicates that a competitive route of fragmentation exists for SCB decomposition on the filament. It has been shown that this competitive route occurs without H/D scrambling. The highly reactive silylene, silene, and methylsilylene species produced from SCB decomposition underwent either insertion reactions into the Si-H bonds of the parent molecule or pi-type addition reaction across the double and triple CC bonds. The dimerization product of silene, 1,3-disilacyclobutane, at m/z = 88 was also observed.     

Synthesis and pyrolysis of oligo(methylsilylene)-ethynylene polymer to near-stoichiometric SiC ceramic

<正>Oligo(methylsilylene)-ethynylene polymer with crosslinkable ethynyl unit in the main chain was synthesized by condensation ofα,ω-dicholorooligo(methylsilane) with dilithioacetylene.The as-synthesized polymer was characterized by GPC,FT-IR and NMR.The results showed ethynyl group was successfully introduced to the polymer main chain.The ceramic yield was dramatically increased by the cross-polymerization of ethynyl group,and the excess silicon of PMS was compensated.Nearstoichiometric (C/Si=1.17) and partial crystallizationβ-SiC monoliths were obtained by pressureless pyrolysing PSPA at 1200℃in a high yield(73.6 wt%).     

HOMO- AND COPOLYMERIZATION OF ETHYLENE CATALYZED BY ANSA-METALLOCENES WITH DOUBLY HETERO-BRIDGES

Three ansa-metallocenes(Me_2C)(Me_2Si)Cp_2TiCl_2(1),[(CH_2)_5C](Me_2Si)Cp_2TiCl_2 (2)and (Me_2C)(Me_2Si)Cp_2ZrCl_2 (3)with larger dihedral angles and longer distance from metal to the center of Cp planes were synthesized and used as catalysts for ethylene polymerization in the presence of methylaluminoxane (MAO).In the case of ethylene polymerization,compared the feature structures of unbridged metallocenes, singly bridged metallocenes and doubly bridged metallocenes 1,2,3,there exhibit the relationship ...     

Copolymerization of 4‐Propanoylphenyl Acrylate with Methyl Methacrylate: Synthesis,Characterization and Reactivity Ratios

The new acrylic monomer 4‐propanoylphenyl acrylate (PPA) was synthesized and copolymerized with methyl methacrylate (MMA) in methyl ethyl ketone at 70±1°C using benzoyl peroxide as a free radical initiator. The copolymers were characterized by FT‐IR, ¹H‐NMR and ¹³C‐NMR spectroscopic techniques. The compositions of the copolymers were determined by ¹H‐NMR analysis. The reactivity ratios of the monomers were determined using Fineman‐Ross (r₁=0.5535 and r₂=1.5428), Kelen‐Tüdös (r₁=0.5307 and r₂=1.4482), and Ext. Kelen‐Tüdös (r₁=0.5044 and r₂=1.4614), as well as by a nonlinear error‐in‐variables model (EVM) method using a computer program, RREVM (r₁=0.5314 and r₂=1.4530). The solubility of the polymers was tested in various polar and non‐polar solvents. The elemental analysis was determined by a Perkin‐Elmer C‐H analyzer. The molecular weights (M_w and M_n) of the copolymers were determined by gel permeation chromatography. Thermogravimetric analysis of the polymers reveals that the thermal stability of the copolymers increases with an increase in the mole fraction of MMA in the copolymers. Glass transition temperatures of the copolymers were found to increase with an increase in the mole fraction of MMA in the copolymers.