便携式X射线荧光光谱法同时测定氧化锌富集物中锌铁氯镉砷

氧化锌富集物的进口能弥补我国锌矿资源的不足,但要求ZnO>50%、Fe<10%、Cl<8%、Cd<0.25%、As<0.6%。目前常采用YS/T 1171.1～10-2017《再生锌原料化学分析方法》检测氧化锌富集物中锌铁氯镉砷含量,该系列检测方法均需要繁琐的湿法样品前处理,测量过程较为冗长,不能满足氧化锌富集物大量进口时快速通关的需求。故实验建立了采用便携式X射线荧光光谱法(PXRF)同时测定氧化锌富集物中锌铁氯镉砷的方法。采用YS/T 1171.3-2017和YS/T 1171.5-2017方法对氧化锌富集物样品进行定值,然后选取21个含量具有梯度的氧化锌富集物样品作为校准样品,建立起各元素X射线荧光强度值与含量的校准曲线。各曲线相关系数在0.8164～0.9999,方法检出限为0.013%～1.95%,各元素的相对标准偏差(RSD,n=11)均小于0.05%。采用本方法和化学方法分别检测氧化锌富集物样品,各元素的本方法检测值与化学分析方法检测值的相对误差均小于20%。本方法能应用到口岸现场进口氧化锌富集物快速筛查,检测一个样品仅需1分钟测量时间,极大地加快了进口氧化锌富集物通关速度。     

Investigation by combined solid‐state NMR and SAXS methods of the morphology and domain size in polystyrene‐b‐polyethylene oxide‐b‐polystyrene triblock copolymers

The microphase structure of a series of polystyrene‐b‐polyethylene oxide‐b‐polystyrene (SEOS) triblock copolymers with different compositions and molecular weights has been studied by solid‐state NMR, DSC, wide and small angle X‐ray scattering (WAXS and SAXS). WAXS and DSC measurements were used to detect the presence of crystalline domains of polyethylene‐oxide (PEO) blocks at room temperature as a function of the copolymer chemical composition. Furthermore, DSC experiments allowed the determination of the melting temperatures of the crystalline part of the PEO blocks. SAXS measurements, performed above and below the melting temperature of the PEO blocks, revealed the formation of periodic structures, but the absence or the weakness of high order reflections peaks did not allow a clear assessment of the morphological structure of the copolymers. This information was inferred by combining the results obtained by SAXS and ¹H NMR spin diffusion experiments, which also provided an estimation of the size of the dispersed phases of the nanostructured copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 55–64, 2010     

Characterization of Polyethylene Nascent Powders Synthesized with TpTiCl2(OR) Catalysts

Summary: Different kinds of polyethylene and ethylene-1-hexene copolymers were synthesized with TpTiCl₂(OR) (Tp = hydrotris(pyrazolyl)borate; R = Et, i-Pr, n-Bu) catalysts with and without H₂. The polymers were characterized by ¹³C NMR, capillary viscosimetry or GPC, and DSC. The homopolymers showed properties characteristic of ultra-high molecular weight polyethylenes (UHMWPE) with linear structure and high density polyethylenes (HDPE) with molecular weights in the range of commercial grades under hydrogen atmosphere. The copolymers showed a 1-hexene incorporation up to 6 mol-%. Important differences in the thermal properties were observed between the first DSC (nascent powders) and the second DSC heatings (melt-crystallized samples), which evidenced the molecular weights influence on the melt-crystallized samples.     

Gel Permeation Chromatography of Polyethylene Terephalate

Abstract

This paper describes the development of the gel permeation chromatography (GPC) technique for the measurements of cyclic trimer content, molecular weights, and molecular weight distribution of polyethylene terephthalate (PET), utilizing a solvent system of o-chlorophenol-chloroform. Mark-Houwink constants for this solvent system are also described.

The GPC technique was applied to the study of the cyclic trimer content, molecular weights and molecular weight distribution of a variety of commercial PET resins. The results indicate that the cyclic trimer content in PET is dependent on molecular weight, polycondensation process and catalyst system. Solidstate polymerized PET contains less cyclic trimer than PET made by the melt-phase process of the same molecular weight. The cyclic trimer content in solid-stated PET appears to be dependent on the conditions of solid-state polymerization.

The polydispersity index determine for a variety of PET samples is higher than the theoretically predicted value of 2.0; however, there is no systematic dependence on molecular weight or polycondensation process.     

Preparation of Poly(serine ester)s by Ring-opening Polymerization of N-Trityl Serine Lactone Under Catalysis of ZnEt2

Poly(N-trityl serine lactone)(PTSL) and mPEG-block-poly(N-trityl serine lactone)(mPEG-b-PTSL, PEG=polyethylene glycol) were synthesized via the ring-opening polymerization of N-trityl serine lactone(TSL) with diethyl zinc(ZnEt₂) as catalyst. The structures of these polymers were confirmed with hydrogen nuclear magnetic resonance(¹H NMR) spectroscopy, carbon nuclear magnetic resonance(¹³C NMR) spectroscopy and infrared(IR) spectrometer. The thermal decomposition temperature and glass transition temperature of PTSL were 241 and 161 ℃, respectively. A series of mPEG-b-PTSL with different molecular weights(M_n's from 7000 to 32000) was obtained by tuning the TSL/mPEG feed ratio. After the removal of the trityl groups, mPEG-block-poly(serine lactone)(mPEG- b-PSL) was obtained as a new kind of cationic block copolymer. Low cytotoxicity of these polymers to L929 cells was confirmed via 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide(MTT) assay.     

Demulsification performance and the relative solubility number (RSN) of modified poly(maleic anhydride-alt-1-dodecene) on naturally asphaltenic crude oil emulsion

The performance of modified poly(maleic anhydride-alt-1-dodecene) with polyethylene glycol (PEG 1000) and polypropylene glycol (PPG 1000) as emulsion breakers was investigated. The de-emulsifiers were characterized by their chemical structures, relative solubility numbers (RSN), EO content, PO content, and partition coefficient (K_p). All the prepared copolymers were characterized by FTIR and ¹H NMR spectroscopic techniques and their molecular weights were determined by gel permeation chromatography (GPC). The surface and interfacial properties for the prepared polymeric surfactants were studied. The results obtained showed that the molecular structure of the prepared de-emulsifiers have direct effect on de-emulsification process. De-emulsifiers with more EO?PO content had higher de-emulsification efficiency.     

三种不同分子结构阴离子表面活性剂胶束微结构的NMR研究

用核磁共振测定自旋-晶格、自旋-自旋弛豫时间(t₁,t₂)、自扩散系数(D),用2DNOESY技术对正十四烷基硫酸钠、β-戊基壬烷基硫酸钠和β-戊基壬烷基聚氧乙烯醚(4)硫酸钠三类阴离子表面活性剂水溶液进行了观测,烷烃链各基团的t₂/t₁值给出了这三类分子形成各自胶束的水合层位点信息以及烷烃链在胶束内核中堆积程度的比较,自扩散系数结果表明,β-戊基壬烷基硫酸钠比正十四烷基硫酸钠形成的胶束的水合动力学半径小,但β-戊基壬烷基聚氧乙烯醚(4)硫酸钠形成的胶束水合动力学半径明显大于其它两类表面活性剂胶束,2DNOESY谱图提供了β-戊基壬烷基聚氧乙烯醚(4)硫酸钠分子中聚氧乙烯基键在胶束外层卷曲排列的信息.     

Ethylene polymerization with a catalyst system titanium tetrachloride—diethylaluminium chloride—diphenylmagnesium in the presence of hydrogen

A study was made of ethylene polymerization with the catalyst system titanium tetrachloride-diethylaluminium chloride—diphenylmagnesium in the presence of hydrogen. The system is highly active even at high content of hydrogen in the system and at high reaction temperatures (90–130°). In the presence of hydrogen, polyethylene was obtained with high density and a full commercial melt index range (0–50 g/10 min), i.e. a wide range of molecular weights. At higher reaction temperatures, some activation of the catalyst system was observed.     

Extended-chain crystals. IV. Melting under equilibrium conditions

Dilatometric melting experiments were performed on an extended-chain crystalline polyethylene with a broad molecular weight distribution and on four samples crystallized from fractionated polyethylenes. The melting curves were compared with computer calculations based on the assumption of eutectic separation. For the fraction of lowest molecular weight, agreement between experiment and calculation was achieved. The melting behavior of all other samples indicated that only for molecular weights up to 10,000–12,000 did eutectic separation occur. The higher molecular weight portion of each sample crystallized in the form of mixed crystals. Of the experimental maximum melting-point lowering of these mixed crystals, 0.1–0.9°C is due to the lower molecular weight diluents. Another 2–3°C lowering in melting point is due to the fact that the phase diagram of polyethylene mixed crystals has a minimum.     

Thiol-ended polyethylene oxide as reactive stabilizer for dispersion polymerization of styrene

 Radical dispersion polymerization of styrene in aqueous ethanol solutions was performed in the presence of a new reactive polyethylene oxide stabilizer with thiol end groups. This reactive stabilizer was compared to the more conventional poly (N-vinyl pyrrolidone). Particles size distribution, molecular weights and kinetics were investigated. Monodispersed polymer particles with diameter in the range 200–2000 nm were obtained depending on the amount of stabilizer used. In all cases, the polyethylene oxide (PEO) sequence of the dispersant was partly incorporated at the surface of the latex particles, but the grafting yield of polyethylene oxide chains was always limited and did not exceed 15%. Part of the stabilizer being unreacted or reacted with low molecular weight polystyrene remained in the continuous phase. Received: 26 September 1996 Accepted: 4 March 1997     

二甲基二茂锆化合物(1,2-Ph2-4-MeCp)2 ZrMe2的合成及催化乙烯聚合反应研究

在惰性气氛下, 用2 mol甲基锂处理二(1,2-二苯基-4-甲基环戊二烯基)二氯化锆, 合成了大立体位阻的二甲基二茂锆化合物[(1,2-Ph2-4-MeCp)2ZrMe2]. 经元素分析、 核磁共振氢谱、 碳谱和X射线晶体衍射分析, 确定了该化合物的结构. 经Al( i Bu)3/Ph3C+B(C6F5)-4活化, 该化合物催化乙烯聚合反应显示出较高的催化活性, 生成高分子量及高熔点聚乙烯. 该体系的特点是在较低的n(Al)/n(Zr)比下即可有效地催化乙烯聚合.     

支状嵌段聚醚的界面聚集行为及对原油乳状液的破乳作用

合成了三种不同聚氧丙烯/聚氧乙烯(PPO/PEO)比例的含苯环支状嵌段聚醚, 通过界面张力、界面流变、表面压以及对原油乳状液的破乳脱水效果的测定, 考察了其界面聚集行为和破乳作用对PEO含量和分子量的依赖性, 并且对比研究了三种支状聚醚分子交联前后的破乳性能. 结果表明, PEO含量高且分子量大者,其单分子界面占据面积大, 在油/水界面达到吸附平衡的时间短, 其油/水界面扩张模量及扩张弹性均高于PEO含量较少者. 但是对原油乳状液的破乳脱水效果则是PEO含量居中的聚醚最好. 温度影响和交联与否的研究表明, 交联并不能提高分子量较大的聚醚对原油乳状液的破乳效果, 温度对聚醚分子交联前后的破乳效果有不同的影响规律. 本研究可为原油集输过程中化学品的选择与应用提供一定的依据.     

水溶性星型卟啉高分子的合成表征及其与牛血清白蛋白的相互作用

利用琥珀酸酐修饰四(p-氨基苯基)卟啉,再与聚乙二醇单甲醚酯化,制备了亲水性卟啉高分子,用IR、UV-Vis、1H NMR、元素分析等方法对其结构进行了表征.利用紫外可见光谱研究了卟啉高分子与牛血清白蛋白(BSA)之间的相互作用.实验结果显示,卟啉高分子与BSA之间不仅存在卟啉与BSA之间的相互作用,而且存在高分子侧臂与BSA之间体积排斥作用,二者综合结果导致卟啉的可见吸收峰表现出不同于小分子卟啉的特征,最大吸收峰位置没有改变,但是吸收强度表现为增色作用.锌离子与卟啉环络合后,增色作用明显,说明络离子可通过配位键增强对BSA的结合.     

Chemical modification of butyl rubber. I. Synthesis and properties of poly(ethylene oxide)-grafted butyl rubber

A new amphiphilic polymer, i.e., poly(ethylene oxide) (PEO)-grafted butyl rubber (IIR-g-PEO), was synthesized by chemical modification of chlorinated butyl rubber (CIIR). This synthesis was based on the reaction between chlorine in CIIR and potassium salt of polyethylene glycol monomethyl ether (PEGM). PEGM's with molecular weights of 750 and 2000 were used. The maximum grafting percent of the resulted copolymers after the purification was ca. 45%, regardless of the molecular weight of PEGM. The microphase separated structure was observed in the films of IIR-g-PEOs. IIR-g-PEO, whose PEO molecular weight was 2000 and whose PEO content was 23.8 wt %, swelled 3.1% in water, and it was six times larger than the swelling of CIIR. The hydrophilicity of grafted polymers depended on the molecular weight of PEO side chains and PEO content. Even when the PEO contents were same in the polymers which were grafted PEGM-750 and PEGM-2000, their swellings in organic solvents were not equal. It was due to the difference of the microphase-separated structures of the grafted polymers. IIR-g-PEO, whose PEO molecular weight was 750 and whose PEO content was 10.3 wt %, swelled 1.5% in water, but showed an excellent emulsifying ability, where an oil-in-water-type emulsion was formed. © 1993 John Wiley & Sons, Inc.     

Light scattering studies of narrow fractions of polyethylene

Small-angle light scattering experiments were conducted on thin films of linear polyethylene fractions over a very wide range of molecular weights. Spherulitic structures were found in all samples with molecular weight 9 × 10⁵ or less. A rodlike morphology predominates for molecular weights between 1 × 10⁶ and 2 × 10⁶. Still higher fractions yield a very disordered superstructure. These results can be correlated with previous studies of the overall crystallization rates and the resulting properties.     

Role of Surface Molecular Architecture and Energetics of Hydrogen Bonding Sites in Adsorption of Polymers and Surfactants

Hydrogen bonding is generally thought to be an ubiquitous adsorption mechanism, which often foils selective adsorption schemes. Through investigation of hydrogen bonding energy and its dependence on surface molecular architecture, it may be possible to develop new methodologies to control the adsorption of surfactants and polymeric flocculants, depressants, and dispersants used in particulate processing industries. A model system using St?ber silica spheres and polyethylene oxide, a polymer known for its ability to form hydrogen bonds, was examined. The effect of two different surface treatments of the silica particles, calcination and rehydroxylation, upon the adsorption of two polymer molecular weights was studied. The adsorption behavior was then linked to the respective surface structures via characterization of the surfaces using FTIR, NMR, and Raman techniques. In this paper role of hydrogen bonding sites and surface architecture on adsorption is discussed. Copyright 2000 Academic Press.     

Study of iron-zinc catalysts by Mössbauer spectroscopy

The Mössbauer parameters were determined on a series of catalyst mixtures of iron and zinc oxides with variable quantities of zinc. From these results, a change in the crystal structure of the iron oxide when introducing zinc into the samples was observed. The corundum structure of the -Fe₂O₃ phase was transformed into the spinel type of zinc ferrite when zinc oxide was present in any quantity. By means of these parameters a strong electronic interaction between the zinc ferrite and the zinc oxide present in excess was evident. The catalysts were analyzed using X-ray fluorescence /XRF/ and X-ray diffraction /XRD/.     

Polyethylene glycol-polyamidoamine dendritic micelle as solubility enhancer and the effect of the length of polyethylene glycol arms on the solubility of pyrene in water

Unimolecular dendritic micelles designed as solubility enhancers were obtained by coupling polyethylene glycol (PEG) to Starburst polyamidoamine (PAMAM) dendrimers. Micelles-750, -2000, and -5000 have a generation 3.0 dendrimer core (32 primary amine end groups) and PEG arms with molecular weights of 750, 2000, and 5000, respectively. The conjugate of dendrimer core and PEG was characterized by MALDI-TOF MS and 1H NMR. 1H NMR was also used to estimate the average number of PEG arms on each dendrimer molecule. A typical hydrophobic compound, pyrene, was sonicated in an excess amount together with micelles at 50 degrees C for 6 h to produce its saturated water solution. The change of the solubility of pyrene was monitored at 334 nm, its maximum adsorption wavelength, by UV-VIS spectra. Concentrated micelles tended to dissolve more pyrene. However, there is no obvious linear relationship between micelle type and the amount of pyrene entrapped within micelles. Micelle-2000 could solubilize more pyrene than micelle-750. It is hypothesized that micelle-5000 did not solubilize more pyrene than micelle-2000 because of the PEG shell disruption by adjacent interpenetration of individual micelles when PEG arm length increased.     

Comparison of the biodegradability of various polyethylene films containing pro-oxidant additives

The biodegradability of high density polyethylene films (HDPE), low density polyethylene films (LDPE) and linear low density polyethylene films (LLDPE) with a balanced content of antioxidants and pro-oxidants (manganese + iron or manganese + iron + cobalt) was studied. Abiotic pre-treatment consisting of photooxidation and thermal oxidation corresponding to about three years of outdoor weathering (including 3-4 months of exposure to daylight) was monitored by FTIR and SEC measurements. The oxidized samples were then inoculated with the strain Rhodococcus rhodochrous in mineral medium, and incubated up to 180 days. The metabolic activity of the bacteria was assessed by measuring adenosine triphosphate content (ATP) and the viability of the cells. Complementary experiments were performed by ¹H NMR spectroscopy to monitor the biodegradation of soluble molecules excreted from the polymer in the incubation medium. Finally SEM was used to visualize the formation of a biofilm at the surface of the polymer. Three samples among the 12 tested were investigated in compost and soil environments. The results show that the main factor controlling the biodegradability of the polyethylene films is the nature of the pro-oxidant additive and to a lesser extent that of the matrix. Except for the samples containing very high content of cobalt additive, the various polymer films were used as substrates by the bacteria.     

石墨烯掺杂纳米氧化锌用于检测三乙胺的增强气敏性能

通过简单研磨实现固相反应的方法制备了纳米氧化锌材料,并利用石墨烯掺杂对氧化锌进行改性,研究了氧化锌材料的气敏性能。利用X射线衍射仪(XRD)、扫描电镜(SEM)、红外光谱仪(IR)对合成的样品进行了结构和形貌表征,考察了原料比例和石墨烯掺杂量对氧化锌形貌和气敏性能的影响。结果表明:合成的氧化锌均为纳米颗粒,随着柠檬酸量增加,得到许多有气孔的氧化锌;石墨烯掺杂后,均得到纳米颗粒的氧化锌;气体检测表明,石墨烯掺杂后的氧化锌,其最佳工作温度由400℃降为280℃,对三乙胺表现出较高的选择性;掺杂3%石墨烯的氧化锌对浓度为0.1 mmol/L三乙胺的响应值(S=Ra/Rg)达到18,是掺杂前的4倍。石墨烯掺杂纳米ZnO可作为检测三乙胺气体的新型传感材料。