Kinetics of the surfactant-free emulsion polymerization of styrene:-The post nucleation stage

The kinetics of the surfactant-free emulsion polymerisation of styrene have been studied. Reactions were sampled at several stages throughout their course, and the samples characterized by electron microscopy, gravimetric weights analysis and gel permeation chromatography, After an initial period of particle nucleation and coagulation, the reaction proceeds at a constant number density. The theories developed for emulsion polymerisation in the presence of surfactant above its critical micelle concentration might be expected, in Interval II, to apply to the surfactant-free system if due regard is taken of the lower number densities and larger particle sizes developed. The results are in best accord with theories invoking a surface phase polymerisation mechanism. None of these theories predict a bimodel molecular weight distribution as found here and which is ascribed to polymerisation in two loci. The activation energy was found to be the same as for surfactant containing emulsion polymerisations.     

Effect of cosolvent NMP on properties of cationic fluorocarbon emulsifier-free emulsion

Cationic fluorocarbon emulsifier-free emulsion was prepared via a novel method of adding organic cosolvent N-methylpyrrolidone (NMP), which was characteristic of the reaction transferring from solution to emulsion polymerization system. The emulsion stability was analyzed by the coagulation and precipitation ratio. The properties of particles were characterized by dynamic laser light scattering, surface potential particle size analyzer, and transmission electron microscopy, respectively. The latex film surface properties and immersion behaviors were investigated by contact angles. The results showed that, with NMP increasing from 5 to 30 %, the emulsion stability became better. Also, particle sizes decreased from 264.0 to 95.5 nm, and their distribution transformed from multidispersion to monodispersion. Zeta potentials increased gently. Meanwhile, the latex film surface performance was slightly improved, and the more the content of NMP, the less the influence of the cure temperature on surface property. There was less mobility of fluorinated groups in the films with more NMP used.

Determination of emulsion explosives with Span-80 as emulsifier by gas chromatography-mass spectrometry

A novel approach for identification and determination of emulsion explosives with Span-80 (sorbitol mono-oleate) as the emulsifier and their postblast residues by gas chromatography-mass spectrometry (GC-MS) has been developed. 24 kinds of emulsion explosives collected have been processed by transesterification reaction with metholic KOH solution and the emulsifier has turned into methyl esters of fatty acids. From the peak area ratios of their methyl esters, most of these emulsion explosives can be differentiated. In order to detect the postblast residues of emulsion explosives, the sorbitols in the emulsifier Span-80 obtained after transesterification reaction have been further derivatized by silylation reaction with N,O-bis-(trimethylsilyl)trifluoroacetamide (BSTFA) containing 1% trimethylchlorosilane (TMCS) as the derivatizing reagent. The derivatization conditions were optimized and the derivatives were determined by GC-MS. The results showed that the silylation derivatives of sorbitol and it isomers, combined with hydrocarbon compounds and methyl esters of fatty acids, were the characteristic components for identification of the emulsion explosives. The established approach was applied to analyze the postblast residues of emulsion explosives. It has been found that the method was sensitive and specific, especially when detecting the derivatives of sorbitol and its isomers by GC-MS in selecting ion mode. The information of the characteristic components can help probe the origin of the emulsion explosives and providing scientific evidences and clues for solving the crimes of the emulsion explosive explosion.     

Characterization of O/W emulsions of carotenes in blackberry juice performed by ultrasound and high-pressure homogenization

Carotene compounds are a group of natural pigments with potential applications in the food industry for their antioxidant activity, but due to their physicochemical instability and incompatibility with many food matrices, different technologies have been employed, such as emulsification, to improve stability and compatibility. Therefore, the physicochemical stability and antioxidant activity of carotene oil-in-water (O/W) emulsions were studied, using carotene compounds extracted from carrot as the oil phase and blackberry juice as the continuous phase. The effect of different factors on the stability of the emulsion – the relative concentration of the dispersed phase, the hydrophilic-lipophilic balance (HLB), the surfactant concentration, and the emulsification method – was assessed using surface response analysis. The emulsion with the best properties was obtained in the phase ratio 2:8 (v/v) with 6% surfactant and an HLB of 16.7. The ultrasound method produced emulsions with higher antioxidant stability and lower carotene degradation rates than those prepared by high pressure, when compared after 60 days of storage at 25°C. This study allowed the development of a stable emulsion with antioxidants in each of the phases of the emulsion that could be incorporated into several types of food products to produce functional foods.     

碳纸负载电极在乳液法合成聚苯胺电化学性能分析中的应用

首次采用碳纸负载聚苯胺(PAn)为工作电极,探讨了反应时间对乳液法合成PAn电化学性能(循环伏安、交流阻抗及塔菲尔曲线)的影响,并通过对产物电导率、产率及特性粘度的对比分析,印证了产物电化学性能的表征结果.实验结果表明,循环伏安曲线均能有效表征出PAn的三对氧化还原特征峰,交流阻抗曲线均出现一个几乎完整的半圆;且产物的循环伏安、交流阻抗、塔菲尔、产率及电导率随反应时间的变化趋势一致,在反应5h时,PAn的各项性能指标较好.结果显示,利用碳纸作为负载电极,可以对乳液法合成PAn的电化学性能实施有效的实时表征.     

Screening of nitrogen mustards and their degradation products in water and decontamination solution by liquid chromatography-mass spectrometry

Analysing nitrogen mustards and their degradation products in decontamination emulsions posed a significant challenge due to the different phases present in such matrices. Extensive sample preparation may be required to isolate target analytes. Furthermore, numerous reaction products are formed in the decontamination emulsion. A fast and effective qualitative screening procedure was developed for these compounds, using liquid chromatography-mass spectrometry (LC-MS). This eliminated the need for additional sample handling and derivatisation that are required for gas chromatographic-mass spectrometric (GC-MS) analysis. A liquid chromatograph with mixed mode column and isocratic elution gave good chromatography. The feasibility of applying this technique for detecting these compounds in spiked water and decontamination emulsion was demonstrated. Detailed characterisation of the degradation products in these two matrices was carried out. The results demonstrated that N-methyldiethanolamine (MDEA), N-ethyldiethanolamine (EDEA) and triethanolamine (TEA) are not the major degradation products of their respective nitrogen mustards. Degradation profiles of nitrogen mustards in water were also established. In verification analysis, it is important not only to develop methods for the identification of the actual chemical agents; the methods must also encompass degradation products of the chemical agents as well so as to exclude false negatives. This study demonstrated the increasingly pivotal role that LC-MS play in verification analysis.     

Advances in self-crosslinking of acrylic emulsion: what we know and what we would like to know

This review covers various strategies that enable self-crosslinking of acrylic emulsion, and gives a detailed idea of different one component (1K) crosslinking systems along with their reaction mechanisms, film properties and applications. The review is categorized into four main parts: (i) self-condensation of N-methylol functionality (ii) reaction of keto-hydrazide or acetoacetoxy-diamine functional group (iii) self-condensation of organofunctional silanes (iv) metal complex (salts, chelates) reaction with backbone functional group such as acetoacetoxy group or carboxylic group (v) UV curable functional monomers. These crosslinking reactions are low-temperature curable and offers excellent film properties than the conventional two-pack (2K) cross-linking emulsion system. This crosslinking system has good potential application in water-based coatings. Various examples are portrayed, along with a discussion of their advantages, drawbacks and limitations.     

Optimized peptide functionalization of thiol‐acrylate emulsion‐templated porous polymers leads to expansion of human pluripotent stem cells in 3D culture

Highly porous polymers produced by polymerization of the continuous phase of a high internal phase emulsion have been developed as scaffolds for 3D culture of human pluripotent stem cells. These emulsion‐templated polymerized high internal phase emulsion (polyHIPE) materials have an interconnected network of pores that provide support for the cells, while also allowing both cell ingress and nutrient diffusion. Thiol‐acrylate polyHIPE materials were prepared by photopolymerization, which, due to a competing acrylate homopolymerization process, leads to a material with residual surface thiols. These thiols were then used as a handle to allow postpolymerization functionalization with both maleimide and a maleimide‐derivatized cyclo‐RGDfK peptide, via Michael addition under benign conditions. Functionalization was evaluated using an Ellman's colorimetric assay, to monitor the residual thiol concentration, and X‐ray photoelectron spectroscopy. Maleimide was used as a model molecule to optimize conditions prior to peptide‐functionalization. The use of triethylamine as a catalyst and a mixed ethanol‐aqueous solvent system led to optimized reaction between surface‐bound thiols and maleimide. Peptide‐functionalized materials showed improved attachment and infiltration of human pluripotent stem cells over 7 days, demonstrating their promise as a scaffold for 3D stem cell culture and expansion. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1974–1981     

燃油氧化脱硫

综述了燃油的氧化脱硫,包括一些具有吸引力的氧化脱硫方法,如H2O2/有机酸,H2O2/杂多酸,H2O2/含钛分子筛和其它非过氧化氢体系(如叔丁基过氧化物等).对本课题组开发的新型乳液催化氧化脱硫体系进行了详细的介绍.在乳液体系中,界面问的传质限制被大大降低.在温和条件下,双亲性乳液催化剂可以将柴油中的含硫化合物选择氧化...     

Catalytic Emulsion Based on Janus Nanosheets for Ultra-Deep Desulfurization

Catalytic Janus nanosheets were synthesized by using an anion-exchange reaction between heteropolyacids (HPAs) and the modified ionic-liquid (IL) moieties of Janus nanosheets. Their morphology and surface properties were characterized by using SEM, energy-dispersive spectroscopy (EDS), FTIR spectroscopy, and X-ray photoelectron spectroscopy (XPS) studies. Because of their inherent Janus structure, the nanosheets exhibited good amphipathic character with ILs and oil to form a stable ILs-in-oil emulsion. Therefore, these Janus nanosheets can be used as both emulsifiers and catalysts to perform emulsive desulfurization. During this process, sulfur-containing compounds at the interface could be easily oxidized and efficiently removed from a model oil. Application of this Janus emulsion brings an efficient, useful, and green procedure to the desulfurization process. Compared with the desulfurization catalyzed by using HPAs in a conventional two-phase system, the sulfur removal of dibenzothiophene (DBT) achieved in a Janus emulsion system was improved from 68 to 97 % within 1.5 h. Moreover, this emulsion system could be demulsified easily by simple centrifugation to recover both the nanosheets and the ILs. Owing to the good structural stability of the Janus nanosheets, the sulfur removal efficiency of DBT could still reach 99.9 % after the catalytic nanosheets had been recycled at least six times.     

Conductive elastomeric nanocomposites based on oxidation of aniline with silver nitrate via inverse emulsion polymerization

The present investigation describes a facile and rapid approach of conductive nanocomposites production and assesses the opportunity of their use as electro‐mechanical sensors. Hybrid materials containing silver and polyaniline nanoparticles reinforcing a thermoplastic elastomeric matrix were studied. The approach developed includes ultrasonically assisted in situ inverse emulsion polymerization of aniline oxidized by a weak oxidant and silver nitrate, and supported with a strong oxidant, ammonia peroxydisulfate. Aniline was doped with dodecylbenzene sulfonic acid in the presence of dissolved styrene–isoprene–styrene thermoplastic elastomer. While conventional polymerization of aniline with silver nitrate takes 2 weeks, by utilization of inverse emulsion polymerization, the reaction time reduces to 5 days. The assistance of a strong oxidant dramatically shortens the reaction time to 30 min. The technique developed results in uniform distribution of polyaniline/silver (PANI/Ag) conductive nanoparticles in the elastomeric matrix. The morphological studies of the films reveal spherically shaped 45 nm Ag particles. The presence of PANI/Ag in the styrene–isoprene–styrene elastomeric matrix enhances the electrical, thermal, and mechanical properties of the nanocomposites. The approach described provides an opportunity of the development of tunable structures and a remarkably distinctive architecture. A rapid electrical resistance response to an applied strain makes the nanocomposites developed useful as sensitive strain sensors. Copyright © 2014 John Wiley & Sons, Ltd.     

Efficient Extraction of Total Polyphenols from Apple and Investigation of Its SPF Properties

The purpose of this study was to evaluate the sun protection factor (SPF) of cosmetic emulsions with the addition of hydroalcoholic apple extract. First, the total polyphenolic content, the antioxidant activity and SPF properties of the extracts obtained by sonication and refluxing were evaluated. The two extraction methods were improved using the central composite design. For cosmetic emulsion that contained a different concentration of apple extract (10–40%), a SPF value between 0.51 and 0.90 was obtained. The most efficient apple extract was obtained by reflux using 50% ethanol and a 60 min extraction time. The concentrated extract was incorporated in a cosmetic emulsion whose SPF maximum was 0.90. Accordingly, due to photoprotective properties, the apple extract can be a candidate for use in cosmetic formulations.     

Effect of surfactants on the porous structure of poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) hydrogels prepared by an emulsion templating method

Stimuli-sensitive porous hydrogels prepared with an emulsion templating method developed by the authors are potentially applicable in the medical and pharmaceutical fields; thermosensitive N-isopropylacrylamide (NIPA) hydrogels having randomly distributed sphere-like cavities have been prepared by the polymerization in an aqueous phase in an oil-in-water (O/W) emulsion, followed by the washing of oil (oleyl alcohol) microdroplets. The surfactant plays a dominant role in the preparation of porous hydrogels and the pore size. This study concerns with the surfactant effects on the stability of pre-gel O/W emulsions. The porous NIPA hydrogels were successfully prepared using the surfactants forming the stable emulsion and their internal structures and swelling properties were characterized. The O/W emulsions and the porous hydrogels prepared using various amounts of oil and surfactant were characterized. The information obtained serves for preparation of porous hydrogels having suitable porous structure for their applications.     

A new approach for the characterization of insoluble amphiphilic copolymers based on their emulsifying properties

The purpose of the present study was to propose a new approach for the characterization of insoluble amphiphilic copolymers using their emulsifying properties. The capacity of four newly-synthesized block copolymers to stabilize a model emulsion formed by mixing equal volumes of water and ethyl acetate was investigated. The copolymers were composed of dextran or heparin and poly(isobutylcyanoacrylate) and were obtained either by anionic or by radical polymerization of isobutylcyanoacrylate in emulsion, initiated on dextran or heparin. A quantitative analysis of the stability of the emulsion obtained with the different copolymers was evaluated using a Turbiscan MA 2000. The results suggested that this approach provides a new methodology for investigating emulsifying properties of polymers that are insoluble in pure solvents, allowing quantitative comparisons to be made between them.     

Effect of emulsion breakage on selectivity in the separation of hydrocarbon mixtures using aqueous surfactant membranes

In liquid membrane separation processes emulsion breakage results in non-selective physical mixing of the feed mixture with the receiving solvent phase. In this paper a model is developed for describing the interphase transfer process, which takes emulsion breakage into account. The overall transfer is envisaged as a result of two parallel transfer mechanisms: (i) diffusive transport across the membrane and (ii) non-selective physical mixing of the feed with the receiving phase due to emulsion breakage. For selective removal of aromatics from non-aromatics in a feed mixture the “ideal” selectivity, β, obtained in the absence of non-selective breakage, will he given as the ratio of the products of the distribution coefficients times the diffusivity in the aqueous membrane phase. Experiments were carried out in a batch stirred cell to determine the permeation rates for a benzene-n-heptane mixture. From the experimentally observed selectivities the contribution due to emulsion breakage was estimated. This fractional breakage was in good agreement with values determined independently using a water-insoluble dye tracer technique, lending support to the developed model. Further experiments were carried out with the system 1-methylnaphthalene-dodecane, and breakage-corrected transfer rates were determined. The model developed in this paper, together with the experimental studies, sheds light on the mechanism of liquid membrane permeation and should aid in scaling-up processes for dearomatization of naphtha and kerosine.     

两亲性杂侧链聚合物刷的合成及其乳化功能

报道了一种随机高密度接枝亲水、疏水聚合物侧链的刷形两亲性聚合物.首先,结合可逆加成-断裂链转移(RAFT)聚合和后修饰方法,得到含叠氮侧基的聚甲基丙烯酸缩水甘油酯(PGMA-N3)作为主链;再分别合成端炔基聚苯乙烯(PS)和端炔基聚环氧乙烷(PEO),然后通过铜催化的叠氮-炔环加成反应,将疏水性PS和亲水性PEO同时高效的接到PGMA主链上,制得两亲性杂侧链的聚合物刷.由凝胶渗透色谱(SEC)分析得知,在主链叠氮基团与两侧链总炔基的摩尔投料比为1∶1的条件下,PS和PEO的接枝效率很高,都大于90%.通过调节主链长度和2种侧链的投料比,获得不同组成的聚合物刷.通过等质量的甲苯/水混合体系,考察两亲性聚合物刷的乳化能力,发现主链聚合度为100,PS∶PEO比例为70∶30的聚合物刷表现出最佳的乳化性能.     

A novel technique for improving interferometric determination of emulsion film thickness by digital filtration

Determination of the thickness of emulsion films by using the film interferometric images is usually less accurate than that of foam films, due to the close values of the refractive indices of the liquid film and adjacent liquid phases (hence, low contrast and high level of noise at high magnification). A new technique was developed to improve the thickness determination by obtaining the interferometric images without directly filtering the illuminating light, as is usually done in the classical Scheludko interferometric technique. The new method then uses digital filtration during the off-line image post-processing to obtain monochromatic interferometric images required for the thickness determination. The technique was tested with foam films stabilised by sodium dodecyl sulfate and successfully applied to determine thickness of toluene-water-toluene emulsion films using the green and red digital filters. Results for emulsion film thickness determined by either the green or red digital filtration are comparable, thus validating the new technique developed here for emulsion films.     

Use of Surfactant-Stabilized Emulsions for the Alkalimetric Determination of Indometacin

The proton-donor properties of 1-(p-chlorobenzoyl)-5-methoxy-2-methylindole-3-acetic acid (indometacin) were studied in emulsions based on different surfactants and their mixtures. A procedure for the alkalimetric titration of indometacin with detecting the titration end-point in the presence of Cresol Red was developed using an emulsion based on dodecylpyridinium chloride. The conditions for determining indometacin in medicinal forms by pH-metric titration were selected.     

Antioxidant and spectroscopic studies of crosslinked polymers synthesized by grafting polymerization of ferulic acid

A novel, simple synthetic strategy for the preparation of crosslinked polymers with significant antioxidant properties is proposed. Ferulic acid (FA), a well‐known antioxidant compound, due to its reactivity toward free radical process, was inserted into a polymeric network with methacrylic acid (MAA) and ethylene glycole dimethacrylate acting as comonomer and crosslinker, respectively. All the reactants were simultaneously mixed in the polymerization feed and one‐pot radical reaction was carried out. Irregular microparticles were prepared by bulk polymerization and microspheres by precipitation polymerization. The materials were characterized by nuclear magnetic resonance–magic angle spinning (NMR‐MAS) studies, to verify effective FA insertion into polymeric networks, and by morphological, dimensional analyses, and water absorption measurement to study their superficial and swelling properties, respectively. Antioxidant properties of materials were evaluated by linoleic acid emulsion system–thiocyanate assay, determination of scavenging activity on DPPH radicals, determination of available phenolic groups in polymeric matrices, and determination of total antioxidant capacity. Copyright © 2009 John Wiley & Sons, Ltd.     

苯胺在十二烷基苯磺酸/水体系中的乳液聚合过程研究

利用光学显微镜和扫描电镜,对以水为介质、十二烷基苯磺酸(DBSA)为乳化剂的苯胺乳液聚合过程进行监测,发现苯胺在水体系中与DBSA反应形成DBSA-苯胺盐的棒状聚集结构,讨论了DBSA、苯胺、氧化剂的配比及浓度对聚合过程中棒状聚集结构的长度和数量及生成聚苯胺的电导率的影响,提出苯胺在DBSA/水体系中的乳液聚合反应是在胶束表面进行的,而棒状聚集结构中的DBSA-苯胺盐单体经水相扩散到乳胶粒子中,形成颗粒状的聚苯胺.