高效液相色谱法分离测定3-取代-(R,S)-β-丙氨酸对映异构体

以1-氟-2,4-二硝基-5-L-缬氨酰胺(Marfey试剂)为衍生试剂,采用反相高效液相色谱法分离了3-取代-(R,S)-β- 丙氨酸对映异构体。采用梯度洗脱(流动相 A:体积分数为0.1%的三氟乙酸乙腈溶液;流动相B:体积分数为0.1%的三氟乙 酸水溶液)成功分离了 32种3-取代-(R,S)-β-丙氨酸衍生物,所有化合物都是R型异构体衍生物(R-L)较S型异构体衍生物 (S-L)先洗脱。除3-羟基苯和4-羟基苯的疏水参数较小,但其取代的β-丙氨酸衍生物的保留时间较长、分离因子较小外, 其他疏水参数大的取代基的β-丙氨酸衍生物保留时间都长于疏水参数小的取代基的β-丙氨酸衍生物。该文同时测定了R -和S-β-丙氨酸的对映体过剩值。     

Modeling of overloaded gradient elution of nociceptin/orphanin FQ in reversed-phase liquid chromatography

The Reversed-phase (RP) gradient elution chromatography of nociceptin/orphanin FQ (N/OFQ), a neuropeptide with many biological effects, has been modeled under linear and non-linear conditions. In order to do this, the chromatographic behavior has been studied under both linear and nonliner conditions under isocratic mode at different mobile phase compositions--ranging from 16 to 19% (v/v) acetonitrile (ACN) in aqueous trifluoracetic acid (TFA) 0.1% (v/v)-on a C-8 column. Although the range of mobile phase compositions investigated was quite narrow, the retention factor of this relatively small polypeptide (N/OFQ is a heptadecapeptide) has been found to change by more than 400%. In these conditions, gradient operation resulted thus to be the optimum approach for non-linear elution. As the available amount of N/OFQ was extremely reduced (only a few milligrams), the adsorption isotherms of the peptide, at the different mobile phase compositions examined, have been measured through the so-called inverse method (IM) on a 5 cm long column. The adsorption data at different mobile phase compositions have been fitted to several models of adsorption. The dependence of the isotherm parameters on the mobile phase composition was modeled by using the linear solvent strength (LSS) model and a generalized Langmuir isotherm that includes the mobile phase composition dependence. The overloaded gradient separation of N/OFQ has been modeled by numerically solving the equilibrium-dispersive (ED) model of chromatography under a selected gradient elution mode, on the basis of the previously determined generalized Langmuir isotherm. The agreement between theoretical calculations and experimental overloaded band profiles appeared reasonably accurate.     

Effect of the flow rate on the measurement of adsorption data by dynamic frontal analysis

The adsorption data of propyl benzoate were acquired by frontal analysis (FA) on a Symmetry-C18 column, using a mixture of methanol (65%, v/v) and water as the mobile phase, at three different flow rates, 0.5, 1.0 and 2.0 mL/min. The exact flow rates Fv were measured by collecting the mobile phase in volumetric glasses (deltaFv / Fv < or = 0.2%). The extra-column volumes and the column hold-up volume were accurately measured at each flow rate by tracer injections. The detailed effect of the flow rate on the value of the amount adsorbed was investigated. The best isotherm model accounting for the adsorption data was the same BET isotherm model at all three flow rates. Only slight differences (always less than 5%) were found between the three different sets of isotherm parameters (saturation capacity, q(s), equilibrium constant on the adsorbent, b(s) and equilibrium constant on successive layers of propyl benzoate, bL). The reproducibility of the same isotherm parameters measured by the inverse method (IM) is less satisfactory, leading to R.S.D.s of up to 10%. A flow rate increase is systematically accompanied by a slight increase of the amount adsorbed. This phenomenon is consistent with the influence of the pressure on the equilibrium constant of adsorption due to the difference between the partial molar volumes of the solute and the adsorbate. The larger average pressure along the column that is required to achieve a larger flow rate causes a larger amount of solute to be adsorbed on the column at equilibrium. This result comforts the high sensitivity and versatility of the FA method for isotherm determination under any kind of situation.     

New thermodynamically consistent competitive adsorption isotherm in RPLC

A new equation of competitive isotherms was derived in the framework of the ideal adsorbed solution (IAS) that predicts multisolute adsorption isotherms from single-solute isotherms. The IAS theory makes this new isotherm thermodynamically consistent, whatever the saturation capacities of these single-component isotherms. On a Kromasil-C(18) column, with methanol-water (80/20 v/v) as the mobile phase, the best single-solute adsorption isotherm of both toluene and ethylbenzene is the liquid-solid extended multilayer BET isotherm. Despite a significant difference between the monolayer capacities of toluene (370 g/l) and ethylbenzene (170 g/l), the experimental adsorption data fit very well to single-component isotherms exhibiting the same capacities (200 g/l). The new competitive model was used for the modeling of the elution band profiles of mixtures of the two compounds. Excellent agreement between experimental and calculated profiles was observed, suggesting that the behavior of the toluene-ethylbenzene adsorbed phase on the stationary phase is close to ideal. For example, the concentrations measured for the intermediate plateau obtained in frontal analysis differ by less than 2% from those predicted by the IAS model.     

Adsorption behavior of the (+/-)-Tröger's base enantiomers in the phase system of a silica-based packing coated with amylose tri(3,5-dimethyl carbamate) and 2-propanol and molecular modeling interpretation

The binary adsorption isotherms of the enantiomers of Tr?ger's base in the phase system made of Chiral Technologies ChiralPak AD [a silica-based packing coated with amylose tri(3,5-dimethyl carbamate)] as the chiral stationary phase (CSP) and 2-propanol as the mobile phase were measured by the perturbation method. The more retained enantiomer exhibits a S-shaped adsorption isotherm with a clear inflection point, the concentration of the less retained enantiomer having practically no competitive influence on this isotherm: In the entire range of concentrations studied, dq2/dC1 approximately 0. By contrast, the less retained enantiomer has a Langmuir adsorption isotherm when pure. At constant mobile phase concentrations, however, its equilibrium concentration in the adsorbed phase increases with increasing concentration of the more retained enantiomer and dq1/dC2 > 0. This cooperative adsorption behavior, opposed to the classical competitive behavior, is exceedingly rare but was clearly demonstrated in this case. Two adsorption isotherm equations that account for these physical observations were derived. They are based on the formation of an adsorbed multi-layer, as suggested by the isotherm data. The excellent agreement between the experimental overloaded elution profiles of binary mixtures and the profiles calculated with the equilibrium-dispersive model validates this binary isotherm model. The adsorption energies calculated by molecular mechanics (MM) and by molecular dynamics (MD) indicate that the chiral recognition arising from the different interactions between the functional groups of the CSP and the molecules of the Tr?ger's base enantiomers are mainly driven by their Van der Waals interactions. The MD data suggest that the interactions of the (-)-Tr?ger's base with the CSP are more favored by 8+/-(5) kJ/mol than those of (+)-Tr?ger's base. This difference seems to be a contributing factor to the increased retention of the - enantiomer on this chromatographic system. The modeling of the data also indicates that both enantiomers can form high stoichiometry complexes while binding onto the stationary phase, in agreement with the results of the equilibrium isotherm studies.     

Adsorption isotherms on nicotinamide-imprinted polymer stationary phase

The molecular-imprinted technique is applied for the preparation of a polymer selector by using methacrylic acid as functional monomer, ethyleneglycol dimethacrylate as the cross-linker, 2,2'-azobisisobutyronitrile as the initiator, and nicotinamide as the template. The adsorption isotherms of nicotinamide and nicotinic acid and the competitive adsorption isotherms of nicotinamide and nicotinic acid on the imprinted stationary phase are determined using rectangular pulse frontal analysis and static method. Aqueous solution is used as the mobile phase in frontal analysis. It is found that the adsorption data fit well to both Langmuir and Freundlich isotherm models.     

Direct enantiomeric TLC resolution of dl-penicillamine using (R)-mandelic acid and l-tartaric acid as chiral impregnating reagents and as chiral mobile phase additive

DL-Penicillamine has been resolved into its enantiomers by normal-phase TLC using L-tartaric acid as chiral impregnating reagent as well as chiral mobile phase additive, while (R)-mandelic acid has been found to be successful as a chiral impregnating reagent. The solvent system acetonitrile-methanol-water (5:1:1, v/v) was found to be successful when L-tartaric acid was used as impregnating agent while the solvent combination acetonitrile-methanol-(0.5% l-tartaric acid in water, pH 5)-glacial acetic acid (7:1:1.1:0.7, v/v) was successful as mobile phase as it contained L-tartaric acid as the chiral additive. (R)-mandelic acid was successful as chiral impregnating reagent with ethyl acetate-methanol-water (3:1:1, v/v), as the mobile phase. The effects of concentration of chiral selectors, temperature and pH were examined on enantiomeric resolution. The spots were detected with iodine vapors and the detection limits were found to be 0.12 microg for each enantiomer of penicillamine with L-tartaric acid, under both the conditions, and 0.11 microg with (R)-mandelic acid.     

Routine high-performance liquid chromatographic determination of ascorbic acid in foods using L-methionine for the pre-analysis sample stabilization

The possibility of use of phosphoric acid (0.2% v/v, pH 2.1) in the mobile phase and co-existing compounds present in foods as the dissolving agent for the pre-analysis sample stabilization were examined for the routine determination of ascorbic acid (AA) in foods by high-performance liquid chromatography (HPLC) with electrochemical detection (ED). The applied potential was set at 400 mV versus an Ag/AgCl reference electrode. It was demonstrated that 0.2% v/v phosphoric acid was the useful mobile phase and l-methionine was the most effective dissolving agent for the pre-run sample stabilization of AA in foods after comparison with other amino acids and water-soluble vitamins. The proposed method was simple, rapid (retention time @ ca. 4 min), sensitive (detection limit: ca. 0.1 ng per injection (5 μl) at a signal-to-noise ratio of 3), highly selective and reproducible (relative standard deviation (R.S.D.); 2.5% (n=7), between-day R.S.D.: 3.7% (5 days)). The calibration graph of AA was linear in the range of 0.1-12.5 ng per injection (5 μl). Recovery of AA was over 90% by the standard addition method. Relationship between structure of compounds and the stability of AA was also examined.     

Numerical determination of the adsorption isotherms of tryptophan at different temperatures and mobile phase compositions

Single-component adsorption isotherm data were acquired by frontal analysis (FA) for tryptophan on a C(18)-Kromasil packed column, using acetonitrile-water solutions of various compositions (2.5, 5, and 7.5% ACN+1% acetic acid) and at five different temperatures between 25 and 65 degrees C. The adsorption isotherm model accounting best for these data is the bi-Moreau model, showing that two types of adsorption sites coexist on the surface and that strong adsorbate-adsorbate interactions take place. Large concentration band profiles of tryptophan were obtained for the three mobile phase compositions, at five different temperatures and the best values of the adsorption isotherm coefficients were determined by the inverse method (IM) of chromatography. The advantages and drawbacks of using the FA and the IM for determining the coefficients of the adsorption isotherm of tryptophan under the experimental conditions selected are discussed. The results of the FA and IM measurements are in good agreement. Both indicate that the retention time of tryptophan decreases rapidly with increasing acetonitrile concentration in the mobile phase as well as the saturation capacities of the two types of adsorption sites, with the highest values of the two saturation capacities being found for the lowest ACN content and the lowest temperature. The adsorption constant on the low-energy sites decreases with increasing acetonitrile content and temperature. In contrast, the adsorption constant on the high-energy sites increases with increasing ACN content of the mobile phase but decreases with increasing temperature. The solute-solute interaction parameters for the low and the high-energy adsorption sites increase rapidly with increasing ACN concentration in the mobile phase and with increasing temperature.     

Determination of mandelic acid enantiomers in urine by derivatization in supercritical carbon dioxide prior to their determination by gas chromatography

The use of a supercritical carbon dioxide reaction medium for the determination of the (R)- and (S)-enantiomers of mandelic acid (MA) is proposed. The process involves a previous derivatization step under supercritical conditions by which the carboxyl group is esterified with methanol, then followed by acylation of the hydroxyl group in methyl MA with pentafluoropropionic anhydride in the absence of a catalyst. These derivatization steps cause no enantiomeric inversion. The derivatized enantiomers are extracted and quantified by gas chromatography. A BETA DEX 225 capillary column allows the separation of (R)-MA and (S)-MA as pentafluoropropionyl methyl esters with good resolution and precision. The overall method was used to determine both enantiomers in urine samples.     

Adsorption isotherms of the fullerenes C60 and C70 on a tetraphenylporphyrin-bonded silica

The single-component adsorption isotherms of the C60 (from 0 to 15 g/L) and C70 (from 0 to 8 g/L) buckminsterfullerenes on a tetraphenylporphyrin-bonded silica were acquired by frontal analysis, using a solution of toluene-1-methylnaphthalene (40:60, v/v) as the mobile phase. The best isotherm model derived from the fitting of these adsorption data was the bi-Langmuir model, a choice supported by the bimodal affinity energy distribution (AED) obtained for C60. The isotherm parameters derived from the inverse method (IM) of isotherm determination (by fitting calculated profiles to experimental overloaded band profiles of C60 and C70) are in very good agreement with those derived from the FA data. According to the isotherm parameters found by these three methods (FA, AED, IM), the tetraphenylporphyrin-bonded silica can adsorb 54 and 42 mmol/L of C60 and C70 fullerenes, respectively, a result that is consistent with the relative molecular size of these two compounds. The 20% lower surface accessibility for C70 is compensated by a three times higher equilibrium constant on the low-energy sites, giving a selectivity alpha(C70/C60) = 3.6. Large volumes (0.2, 0.8 and 1.7 mL) of mixtures of C60 (3.2 g/L) and C70 (1.3 g/L) were injected and their elution profiles compared to those calculated from the competitive bi-Langmuir model derived from the single-component isotherm data. A good agreement is obtained between calculated and experimental profiles, which supports the two-site adsorption mechanism derived from the single-component adsorption data. The measurements of the influence of the pressure on the retention of C60 and C70 demonstrate that the partial molar volumes of the two buckminsterfullerenes are 12 mL/mol larger in the stationary than in the mobile phase.     

前沿分析法研究对-羟基苯甲酸印迹整体柱的热力学行为

采用矩形前沿分析法对原位聚合的对-羟基苯甲酸印迹整体柱的热力学吸附等温线进行了测定. 印迹整体柱的吸附等温线是分别以乙腈、甲醇、 四氢呋喃和含有体积分数分别为1%, 3%, 5%和7%乙酸的乙腈为流动相以及在以甲醇为流动相时柱温分别为20, 40和50 ℃的条件下测定的. 吸附等温线表明, 印迹整体柱对模板分子的吸附能力比其结构类似物(邻-羟基苯甲酸)的吸附能力强. 用双Langmuir方程对不同条件下得到的实验数据进行拟合, 得到模板分子和邻-羟基苯甲酸在印迹整体柱各种吸附位点上的饱和吸附量和键合常数, 结果表明, 流动相中乙酸含量、有机溶剂的性质和柱温对模板分子容量因子的影响比对邻-羟基苯甲酸的大, 造成印迹聚合物的选择性随条件的变化而发生了明显的改变.     

Accuracy and precision of adsorption isotherm parameters measured by dynamic HPLC methods

The fluctuations of the column temperature, the composition and the flow rate of the mobile phase affect the accuracy and precision of the adsorption isotherm parameters measured by dynamic HPLC methods. Experimental data were acquired by frontal analysis (FA) for phenol in equilibrium between C18-bonded Symmetry and a methanol:water mixture (20:80, v/v), at 303 K and a flow rate of 1 mL/min. The fluctuations of the experimental parameters were 0.1 K for the temperature, 0.1% for the mobile phase composition and 0.001 mL/min for the flow rate. The best isotherm model was shown to be the tri-Langmuir isotherm. Random errors were calculated and shown to agree with experimental results. Overloaded band profiles of phenol were acquired at low (sample size, 100 microL, concentration 3 g/L) and high (same sample size, concentration 60 g/L) loadings, at seven temperatures (298, 300, 302, 303, 304, 306, and 308 K), for seven mobile phase compositions (methanol 16, 18, 19, 20, 21, 22, and 24%), and with seven mobile phase flow rates (0.95, 0.97, 0.99, 1.00, 1.01, 1.03, and 1.05 mL/min), always keeping two experimental parameters at the values selected for the FA runs. Assuming that the isotherm model stays the same, the inverse method (IM) was used to derive the isotherm parameters in each case. Temperature affects the equilibrium constants according to Van't Hoff law. A temperature change of 1 K around 303 K causes a relative variation of 1.5% of the high-energy adsorption constant b3 and of 0.6% of the saturation capacity q3. The isotherm parameters are very sensitive to the mobile phase composition, especially the highest energy mode. Both adsorption constants b2 and b3 follow the linear strength solvent model (LSSM). A methanol volume fraction change of 1% causes a relative decrease of 3.2 and 5.0% of b2 and b3, respectively and a 2% decrease of the saturation capacity q3. Finally, flow rate changes affect only the saturation capacities. A flow rate change of 1 % causes a 2% change in the saturation capacity parameters.     

酰胺型手性固定相反相拆分布洛芬药物对映体

利用酰胺型手性固定相反相拆分了布洛芬对映异构体,用有０．０１ｍｏｌ／Ｌ ＮＨ４Ａｃ的甲醇和水作流动相。在优化分离条件的同时,研究了不同的有机调节和对分离的影响,并探讨了分离的机理。     

Synthesis of Chlorogenic Acid Imprinted Chromatographic Packing by Surface-initiated Atom Transfer Radical Polymerization and Its Application

A novel chromatographic packing of chlorogenic acid（CGA） molecularly imprinted polymer（MIP） based on the 5.0 ~tm silica was prepared by surface initiated atom transfer radical polymerization（SI-ATRP） with 4-vinylpyridine（4-VP） as functional monomer, ethyl glycol dimethacrylate（EDMA） as cross-linker in the mixture of methanol and water（7：3, volume ratio） under mild reaction conditions. The characteristics of CGA MIP were investi- gated by elemental analysis, thermogravimetric analysis（TGA）, Fourier transform infrared spectrometry（FTIR） and atomic force microscopy（AFM）. The effects of some chromatographic conditions such as mobile phase composition and temperature on the retention time were investigated. The adsorption capacity of the stationary phase for com- pounds was determined by frontal chromatographic technique. The results show that Freundlich isotherm fits the ex- perimental adsorption isotherm data better than Langmuir model does. The relatively high heterogeneity index values regressed with the Freundlich isotherm suggest the formation of fairly homogeneous MIP. Thermodynamic data（AAH and AAS） obtained by van＇t Hoff plots reveal an entropy-controlled separation. The CGA MIP column was shown to be successful for the separation and purification of chlorogenic acid from the extract of Honeysuckle.     

手性高效液相色谱拆分3-取代异吲哚-1-酮的研究

从伏牛花类植物中提取的生物碱Lennoxam ine^[1]、Nuevam ine和Chilenine,新研发的抗焦虑药Paz-inaclone^[2]和Pagoclone^[3]以及利尿、抗高血压药Chlortalidone^[4]等均含有光活性3-取代异吲哚-1-酮(2,3-二氢-1H -异吲哚-1-酮).这类化合物还是一类新型的不对称合成手性辅助基^[5].因此,光学纯的3-取代异吲哚-1-酮化合物在药物研发和不对称合成等领域具有应用前景.但有关它们的色谱拆分少见报道^[6,7].本文对15个外消旋3-取代异吲哚-1-酮样品进行高效液相色谱拆分研究,通过建立的手性色谱方法,不仅准确测定了相关产物的光学纯度,而且确认了N -取代邻苯二甲酰亚胺上手性辅助基在不对称合成过程^[8]中未发生消旋化.同时探讨了样品中3-位取代基对手性拆分的影响.     

RP-HPLC拆分普萘洛尔对映体的洗脱顺序及其荧光响应研究

应用反相高效液相色谱法,以（Ｒ,Ｒ）－Ｏ,Ｏ－二乙酰基酒石酸酐（ＤＡＴＡＡＮ）为手性衍生化试剂,拆分了普萘洛尔（ｐｒｏｐｒａｎｏｌｏｌ）对映体。实验结果显示：普萘洛尔对映体经衍生化而生成的两个非对映异构体分子的空间结构有着明显的差异,即（Ｒ,Ｒ,Ｒ）－异构体中存在着分子内氢键,而（Ｒ,Ｒ,Ｓ）－异构体中却没有,这种结构上的区别不仅成为控制洗脱顺序的主要因素,而且对其荧光响应也产生重要的影响。     

Band splitting in overloaded isocratic elution chromatography II. New competitive adsorption isotherms

The equations of two new binary competitive isotherms models are derived. The first of these models assumes that the isotherms of the two pure, single compounds have distinct monolayer capacities. Its derivation is based on kinetic arguments. The ideal adsorbed solution (IAS) framework was applied to derive the second model that is a thermodynamically consistent competitive isotherm. This second model predicts the competitive adsorption isotherm behavior of a mixture of two compounds that have single-component adsorption behavior following a BET and/or a Langmuir isotherms. Both models apply well to the binary adsorption of ethylbenzoate and 4-tert.-butylphenol on a Kromasil-C18 column (with methanol-water, 62:38, v/v, as the mobile phase). The best single-solute adsorption isotherms of these two compounds are the liquid-solid extended multilayer BET and the Langmuir isotherms, respectively. The kinetic and thermodynamic new competitive models were compared, regarding the accuracy of their prediction of the elution band profiles of mixtures of these two compounds. A better agreement between experimental and calculated profiles was observed with the kinetic model. The IAS model failed because the behavior of the ethylbenzoate/4-tert.-butylphenol adsorbed phase mixture is probably non-ideal. The most striking result is the qualitative prediction by these models of the peak splitting of 4-tert.-butylphenol during its elution in presence of ethylbenzoate.     

Determination of vigabatrin in human plasma and urine by high-performance liquid chromatography with UV-Vis detection

A simple and reliable high-performance liquid chromatographic (HPLC) method with UV-Vis detection has been developed and validated for the determination of vigabatrin (VG) in human plasma and urine. The samples were pre-column derivatizated with 1,2-naphthoquinone-4-sulphonic acid sodium salt (NQS). A good chromatographic separation was achieved on a C18 column with a mobile phase consisting of acetonitrile and 10 mM orthophosphoric acid (pH 2.5) gradient elution. Tranexamic acid was used as an internal standard (I.S.). The method was linear over the concentration range of 0.8-30.0 microg/ml for both samples. The method is precise (relative standard deviation (R.S.D.) <9.13%) and accurate (relative mean error (RME) <-8.75%); analytical recoveries were 81.07% for plasma and 83.05% for urine. The assay was applied to pharmacokinetic study in a healthy volunteer after a single oral administration of 1 g of vigabatrin.