Interaction between two double-layers for FeCl<Subscript>3</Subscript> and Na<Subscript>3</Subscript>PO<Subscript>4</Subscript> type electrolytes in case the signs of potentials on two plates are opposite

The interaction energies between two double layers for FeCl₃ or Na₃PO₄ type electrolytes at y ₀ > 0 >y _d>—y ₀ were calculated with the aid of 7n parameter methods and the accurate numeral results were given when the dimensionless surface potential of two double layers changes from -20 to +20. When ∣y _d∣ > 5, the absolute value of the interaction energies, ∣V’∣, for FeCl₃ type electrolytes at y ₀= 1 stops to increase. When y ₀> 8, the ∣V’∣ for FeCl₃ type electrolytes at y _d= -1 ceases to change. The influence of y _d on ∣V’∣ for FeCl₃ type electrolytes is more significant than the influence of y ₀. The variation of ∣V’∣ with y _d and y ₀ for Na₃PO₄ type electrolytes is opposite to that for FeCl₃ type electrolytes. The interaction energies between two dissimilar double layers for Na₂SO₄, CaCl₂, NaCl, Na₃PO₄ and FeCl₃ type electrolytes at y ₀= 1 and y _d = -10 are compared and the results indicate that the interaction energies close to each other for FeCl₃ and CaCl₂ type electrolytes and for Na₃PO₄ and Na₂SO₄ type electrolytes, respectively. ∣V’∣ increases with the raises of y ₀ or ∣y _d∣, but decreases with the raises of z ₊ or z _-.     

Electrochemical Synthesis of Co-intercalation Compounds in the Graphite-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>-H<Subscript>3</Subscript>PO<Subscript>4</Subscript>System

Anodic oxidation of highly oriented pyrolytic graphite in an electrolyte containing concentrated sulfuric and anhydrous phosphoric acids is studied for the first time. The synthesis was carried out under galvanostatic conditions at a current I = 0.5 mA and an elevated temperature (t = 80°C). Intercalation compounds of graphite (ICG) are shown to form at all concentration ratios of H₂SO₄ and H³PO⁴ acids. The intercalation compound of step I forms in solutions containing more than 80 wt % H₂SO₄, a mixture of compounds of intercalation steps I and II forms in 60% H²SO⁴, intercalation step II is realized in the sulfuric acid concentration range from 10 to 40%, and a mixture of compounds of intercalation steps III and II is formed in 5% H₂SO₄ solutions. The threshold concentration of H₂SO₄ intercalation is ∼2%. With the decrease in active intercalate (H₂SO₄) concentration, the charging curves are gradually smoothed, the intercalation step number increases, and the potentials of ICG formation also increase. As the sulfuric acid concentration in the electrolyte changes from 96 to 40 wt %, the filled-layer thickness d _i in ICG monotonously increases from 0.803 to 0.820 nm, which apparently is associated with the greater size of phosphoric acid molecules. With further increase in H₃PO₄ concentration in solution, d _i remains unchanged. According to the results of chemical analysis, both acids are simultaneously incorporated into the graphite interplanar spacing and their ratio in ICG is determined by the electrolyte composition.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 651–655.Original Russian Text Copyright © 2005 by Leshin, Sorokina, Avdeev.     

Determination of the enthalpy of fusion of Na<Subscript>3</Subscript>FeF<Subscript>6</Subscript>

The areas of the fusion and crystallization peaks of Na₃FeF₆ and of four calibration substances (KCl, NaCl, Na₂SO₄, and K₂SO₄) were measured using the DSC mode of a high-temperature calorimeter. Using the measured quantities and known values of the enthalpy of fusion of the calibration substances, the enthalpy of fusion of Na₃FeF₆ was determined. Its value at the temperature of fusion 1224 K was 70 ± 4 kJ mol⁻¹.     

Structure and electric properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-NaPO<Subscript>3</Subscript> glasses

The influence of the SO₄²⁻ ion on the temperature and concentration dependences of electric conductivity and the structure of sodium phosphate oxide glasses was studied. The increased electric conductivity of sulfate-phosphate glasses was explained by the formation of mixed sulfate-phosphate fragments with terminal SO₄²⁻ ions in the structure of glasses in the Na₂SO₄-NaPO₃ system. The dissociation energies of the sodium sulfate fragments are lower than those of pure oxide sodium phosphate structural units. As a result, the number of dissociated sodium ions increases, the activation energy of electric conductivity falls, and the conductivity (at 25°C) increases approximately 270-fold relative to the conductivity of NaPO₃. The arrangement of SO₄²⁻ ions in the structure was evaluated from the IR spectra of the glasses.     

Influence of the exchangeable cations on SO<Subscript>2</Subscript> adsorption capacities of clinoptilolite-rich natural zeolite

The sulfur dioxide adsorption on clinoptilolite-rich tuff from Bigadiç region of Western of Turkey and its modified forms (Na⁺, K⁺, Ca²⁺ and Mg²⁺) have been studied at 273 K and 293 K up to 100 kPa. The structural properties of clinoptilolites were studied by X-ray diffraction (XRD) and Fourier transform infrared (FT-IR). The quantitative XRD analysis demonstrated that the Natural-B sample is mainly constituted by clinoptilolite (80–85%) with minor contents of quartz (7–8%), feldspar (5–6%) and mica-illit (4–5%). It was found out that the adsorption capacity and the affinity of SO₂ with clinoptilolite samples depended mainly on the type of exchanged cations and decreased as Na-B > K-B > Mg-B > Natural-B > Ca-B for both temperature. These results show that clinoptilolite-rich zeolites are considered potentially good adsorbents for SO₂ removal.     

Solubility in the ternary system CaSO<Subscript>4</Subscript> + Na<Subscript>2</Subscript>SO<Subscript>4</Subscript> + H<Subscript>2</Subscript>O at 298.15 K

The solubility in the ternary system, aqueous mixture of CaSO₄ and Na₂SO₄, at T = 298.15 K comprises five different salts: calcium sulfate dihydrate, mirabilite, thenardite, glauberite and labile salt. Using the Extended Pitzer’s Ion Interaction model for pure and mixed electrolyte solutions and criteria of phase equilibria, predicted solubility behavior of salts was compared with experimental results from literature. The agreement between calculated and experimental solubilities was excellent in the ionic strength range up to 10.9062 mol kg⁻¹.     

Phase ratios in the M<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-SO<Subscript>3</Subscript> (M = Rb,Cs) systems and the properties of the compounds formed in these systems

Powder X-ray diffraction and microscopy have been used to study phase ratios of the M₂O-V₂O₅-SO₃ (M = Rb, Cs) systems, which model the active component of rubidium-vanadium and cesium-vanadium catalysts for sulfuric acid production at high sulfur dioxide conversions. We have stated that each system forms four compounds: M₃VO₂(SO₄)₂, MVO₂SO₄, M₄V₂O₃(SO₄)₄, and MVO(SO₄)₂. The thermal properties of these compounds and their interaction with water vapor saturated at room temperature have been studied. The unit cell parameters have been determined for the compounds MVO₂SO₄ (M = K, Rb), MVO(SO₄)₂, and M[VO₂(SO₄)(H₂O)₂] · H₂O (M = Rb, Tl). The reciprocal transformations of the components and phases of the M₂O-V₂O₅-SO₃ systems match the Lux-Flood ideas of the acid-base properties of oxide compounds.     

Study on the non-isothermal kinetics of decomposition of 4Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>·2H<Subscript>2</Subscript>O<Subscript>2</Subscript>·NaCl

The non-isothermal decomposition kinetics of 4Na₂SO₄·2H₂O₂·NaCl have been investigated by simultaneous TG-DSC in nitrogen atmosphere and in air. The decomposition processes undergo a single step reaction. The multivariate nonlinear regression technique is used to distinguish kinetic model of 4Na₂SO₄·2H₂O₂·NaCl. Results indicate that the reaction type Cn can well describe the decomposition process, the decomposition mechanism is n-dimensional autocatalysis. The kinetic parameters, n, A and E are obtained via multivariate nonlinear regression. The n ^th-order with autocatalysis model is used to simulate the thermal decomposition of 4Na₂SO₄·2H₂O₂·NaCl under isothermal conditions at various temperatures. The flow rate of gas has little effect on the decomposition of 4Na₂SO₄·2H₂O₂·NaCl.     

LiF-LiCl-LiVO<Subscript>3</Subscript>-Li<Subscript>2</Subscript>SO<Subscript>4</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript> system

Phase equilibria in the LiF-LiCl-LiVO₃-Li₂SO₄-Li₂MoO₄ system have been studied by differential thermal analysis. The eutectic composition has been determined as follows (mol %): LiF, 17.4; LiCl, 42.0; LiVO₃, 17.4; Li₂SO₄, 11.6; and Li₂MoO₄, 11.6, with the melting temperature equal to 363°C and the enthalpy of melting equal to (284 ± 7) kJ/kg.     

Solid‐Liquid Equilibria in the Quinary Na+, K+//Cl−, SO2−4, B4O2−7‐H2O System at 298 K

The solid‐liquid equilibria in the quinary system Na⁺, K⁺//Cl^?, SO^2?₄, B₄O^2?₇‐H₂O at 298 K had been studied experimentally using the method of isothermal solution saturation. Solubilities and densities of the solution of the quinary system were measured experimentally. Based on the experimental data, the dry‐salt phase diagram and water content diagram of the quinary system were constructed, respectively. In the equilibrium diagram of the quinary system Na⁺, K⁺//Cl^?, SO^2?₄, B₄O^2?₇‐H₂O at 298 K, there are five invariant points F1, F2, F3, F4 and F5; eleven univariant curves E1F1, E2F2, E3F3, E4F5, E5F2, E6F4, E7F5, F1F4, F2F4 F1F3 and F3F5, and seven fields of crystallization saturated with Na₂B₄O₇ corresponding to Na₂SO₄, Na₂SO₄·10H₂O, Na₂SO₄·3K₂SO₄ (Gla), K₂SO₄, K₂B₄O₇·4H₂O, NaCl and KCl. The experimental results show that Na₂SO₄·3K₂SO₄ (Gla), K₂SO₄ and K₂B₄O₇·4H₂O have bigger crystallization fields than other salts in the quinary system Na⁺, K⁺//Cl^?, SO^2?₄, B₄O^2?₇‐H₂O at 298 K.     

Solid surface and field catalysed interface formation of colloidal Al<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>3</Subscript> during Al anodizing affecting the kinetics and mechanism of development and structure of porous oxides

Overall kinetic and potentiometric studies of the growth of porous anodic alumina films in saturated H₂SO₄+Al₂(SO₄)₃ electrolyte showed non-saturation conditions inside the pores and supersaturation conditions at the pore surface/electrolyte interface where the field and the solid surface catalyse the formation of colloidal Al₂(SO₄)₃ micelles. Suitable high-strength field thermodynamically sustained electrochemical and chemical kinetic equations were formulated. It was shown that the diameter and surface fraction of charge exchange at the pore bases, the real pore wall surface fraction where oxide dissolution occurs, and its rate are strongly affected by the conditions. The mechanism of growth and structure of the films are quite different from those in H₂SO₄. A mechanism of regular film growth is imposed and the critical current density, above which pitting appears, strongly increases. The formulated theory may predict improved or new Al anodizing technologies. Electronic Publication     

Effect of SO<Subscript>2</Subscript> on SCR activity of MnOx/PG catalysts at low temperature

Palygorskite (PG)-supported manganese oxide catalysts (MnOx/PG) were prepared for the selective catalytic reduction (SCR) of NO with ammonia in the presence of SO₂ at low temperature. The influence of gaseous SO₂ on the performance of the catalyst was studied by means of specific surface area (Brunauer-Emmett-Teller, BET) analysis, scanning electron microscopy (SEM), thermogravimetric (TG) analysis, temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS). The results showed that the SCR activity of Mn10/PG was significantly inhibited by gaseous SO₂ at temperatures below 300°C. However, the SCR activity of Mn10/PG was markedly promoted by SO₂ in a higher temperature range of 300°C to 500°C. The sulphating of surface active species (MnOx) was suggested to inhibit the oxidation of NH₃ to NO leading to enhancement of the SCR activity at a higher temperature range of 300°C to 500°C and decrease in the SCR activity at temperatures below 300°C.     

Influence of composition on corroding process of Na<Subscript>2</Subscript>O-K<Subscript>2</Subscript>O-CaO-ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glasses

The corroding process of six glasses of the Na₂O-K₂O-CaO-ZrO₂-SiO₂ system with ZrO₂content 0–2.13 mass % by water was observed during static tests at 121°C and pressure of 0.25 MPa in steam sterilizer. Significant increase of Na⁺ and K⁺ content in leachates was observed after the addition of ZrO₂ into glass. Further increase of the content of ZrO₂ in glasses slowed down the rate of Na⁺ and K⁺ leaching. The leaching process of SiO₂ as well as Na⁺, K⁺, and Ca²⁺ ions was evaluated on the basis of comparison with model leaching processes. Variation of the concentrations of Na⁺, K⁺, Ca²⁺, and SiO₂ in leachates with time was described by empirical equation. Observed changes in the initial leaching rates of Na⁺, K⁺, Ca²⁺, and SiO₂ can be ascribed to the content of ZrO₂ in glasses. The presence of ZrO₂ in glasses reduced the overall rate of glass dissolution.     

Orientational disorder in crystal structures of (NH<Subscript>4</Subscript>)<Subscript>3</Subscript>ZrF<Subscript>7</Subscript> and (NH<Subscript>4</Subscript>)<Subscript>3</Subscript>NbOF<Subscript>6</Subscript>

Crystal structures of (NH₄)₃ZrF₇ (I) and (NH₄)₃NbOF₆ (II) are refined by X-ray diffraction at room temperature. The compounds are isostructural and belong to the structural type of elpasolite: space group F23; a(I) = 9.4185(3) Å, a(II) = 9.3371(5) Å; V(I) = 835.50(5) ų, V(II) = 814.02(8) ų; Z = 4; R(I) = 0.0145, and R(II) = 0.0138. The refinement of the structures in the space group Fm3m yields abnormally short X-X distances in the pentagonal bipyramid MX₇ (X = F, O). The oxygen atom in II is identified by Nb-X distances and occupies one of the axial vertices of the bipyramid. The Nb atom in II is statistically distributed over the position 24f, while Zr in I resides in the symmetry center. The pentagonal bipyramid MX₇ has six independent orientations in I and twelve in II. One of three crystallographically independent ammonium groups of the structures is disordered over six or twelve equivalent orientations.     

Study on electrochemical performance of activated carbon in aqueous Li2SO4, Na2SO4 and K2SO4 electrolytes

The electrochemical performances of activated carbon (AC) in 0.5 mol/l Li₂SO₄, Na₂SO₄ and K₂SO₄ aqueous electrolytes were investigated. The cyclic voltammetric results at different scan rates show that the rate behaviors of AC in the three electrolytes improve in the order of Li₂SO₄ < Na₂SO₄ < K₂SO₄. This improvement can be mainly ascribed to the following two reasons: (1) the decreasing equivalent series resistance in the order of Li₂SO₄ > Na₂SO₄ > K₂SO₄, which is the main factor influencing the maximum output power, and (2) the increasing migration speed of hydrated ions in the bulk electrolyte and in the inner pores of AC electrode in the order of Li⁺ < Na⁺ < K⁺. Their cycling behaviors do not show any differences in capacitive fading. The above results provide valuable information to explore new hybrid supercapacitors.     

Electrochemical processes of H<Subscript>2</Subscript>S detection in air and solution

An electrochemical cell of potentiometric type Na_0.5WO₃ (reference electrode)/Na⁺-solid electrolyte/PbS (working electrode) capable of rapid and selective changing of the electromotive force value owing to H₂S concentration variations in gas surroundings has been investigated at 295±1 K and a relative humidity of 52%. The sensitivity of this cell was 130 mV/decade at a H₂S concentration within the range 13–130 ppm. Sodium-conducting solid electrolytes of Na₃Zr₂Si₂PO₁₂ and Na₅GdSi₄O₁₂ compositions were used as the Na⁺ solid electrolyte. Such a cell can be used for analysis of H₂S containing water solutions when the reference electrode and the Na⁺ solid electrolyte are thoroughly isolated from the surroundings. Electronic Publication     

Surface characteristics of anodic oxide films fabricated in acid and neutral electrolytes on Ti–10V–2Fe–3Al alloy

Anodic oxide films were fabricated on Ti–10V–2Fe–3Al alloy in acid (H₂SO₄/H₃PO₄) and neutral environmental friendly (C₄H₄O₆Na₂) electrolytes. The morphology, roughness, crystalline structure of the anodic oxide film were characterized by using scanning electron microscopy, atomic force microscopy, Raman spectroscopy and electrochemical impedance spectroscopy (EIS). The results showed that the oxide film fabricated in H₂SO₄/H₃PO₄ electrolyte had a porous structure and the thickness of the film was 3.5 µm. The oxide film fabricated in C₄H₄O₆Na₂ electrolyte presented a nonporous structure that sustained the evident microstructure of the substrate, and the thickness of the film was 6.0 µm. The surface average roughness values of the two types of films were 245 nm and 166 nm, respectively. The phase of the anodic oxide films consisted mainly of anatase and rutile. EIS results showed that the film fabricated in C₄H₄O₆Na₂ electrolyte had higher impedance of the outer layer, while the film fabricated in H₂SO₄/H₃PO₄ electrolyte had higher impedance of the inner layer. Moreover, we attempt to explain the differences in the anodizing kinetics, structure and electrochemical impedance of anodic oxide films by the different films growth processes in the two types of electrolytes. Copyright © 2012 John Wiley & Sons, Ltd.     

Interaction between two similar plane parallel double layers for Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> type asymmetric electrolytes at positive surface potential

The interaction between two similar plane double-layers for Mg₃(PO₄)₂ type asymmetric electrolytes was investigated with the aid of λ parameter method. The interaction energies for the system at positive surface potential were expanded in power series at low and high potential, respectively. The accurate numeral results and V′-ξ _d curves were given for y ₀ ≤ 20 and they can be used to check up the validity of approximate expressions obtained. When y ₀ ≥ 5, V′ hardly changes with y ₀. The interaction energies between two similar plane parallel double layers for symmetric and asymmetric electrolytes at y ₀ = 1 were compared; when ξ _d is small, the interaction energies for Mg₃(PO₄)₂ type electrolytes increase more drastically than for other type electrolytes. The present results are also fit for Al₂(SO₄)₃ type asymmetric electrolytes at negative surface potential. The article is published in the original.     

Preparation of CuCr<Subscript>2</Subscript>O<Subscript>4</Subscript> nanopowders using two different chromium sources

CuCr₂O₄ spinel powders were synthesized starting from different chromium sources, namely (i) chromium oxide (α-Cr₂O₃) and (ii) ammonium dichromate ((NH₄)₂Cr₂O₇). The copper source was a Cu(II) carboxylate-type complex. The Cu(II) carboxylate complex was obtained by the redox reaction between Cu(NO₃)₂·3H₂O and 1,3-propanediol (1,3PG) at 130 °C. In the first case (i), we have started from a mixture of α-Cr₂O₃, Cu(NO₃)₂·3H₂O and 1,3PG that upon heating formed the copper malonate complex, which decomposed around 220 °C forming an oxide mixture (CuO + α-Cr₂O₃). In the second case (ii), (NH₄)₂Cr₂O₇, Cu(NO₃)₂·3H₂O and 1,3PG were homogenously mixed. Heating this mixture at 130 °C resulted, in situ, in the Cu(II) complex. On controlled temperature increase, the violent decomposition of (NH₄)₂Cr₂O₇ took place at 180 °C along with the decomposition of the Cu(II) complex, leading to an amorphous oxide mixture of Cr₂O_3+x and CuO. By annealing the samples in the temperature range 400–1000 °C, the spinel phase (CuCr₂O₄) was obtained in both cases: (i) at 800 °C and (ii) at 600 °C as a result of the interactions between the precursors used, when the oxide system was amorphous and highly reactive. The presence of CuCr₂O₄ was highlighted by XRD and FTIR analyses.     

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

以FeCl₃-甲基橙(MO)为模板, 通过化学原位聚合法成功制备出氧化石墨烯/聚吡咯(GO/PPy)插层复合材料. 采用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)和透射电镜(TEM)等测试技术对复合材料进行物性表征. 此外, 利用循环伏安、恒电流充放电和交流阻抗测试方法对复合材料在两种不同水系电解液(1 mol·L^-1 Na₂SO₄和1 mol·L^-1 H₂SO₄)中的电化学性能进行了研究. 结果显示: 氧化石墨烯和聚吡咯表现出各自优势并发挥协同作用, 使得GO/PPy插层复合材料在中性和酸性电解液中都显示出可观的比电容. 电流密度为0.5 A·g^-1时, GO/PPy 插层复合材料在Na₂SO₄和H₂SO₄电解液中的比电容分别为449.1 和619.0 F·g^-1, 明显高于纯PPy的比电容. 经过800 次循环稳定性测试后, 两种不同电解液中, 复合材料初始容量的保持率分别为92%和62%. 其中酸性电解液体系中初始容量更大, 而中性溶液中具有更稳定的循环性能.