Arsenic speciation by coupling capillary zone electrophoresis with mass spectrometry

Summary Capillary zone electrophoresis (CZE) has been coupled with mass spectrometry to enable the identification of mineral and organometallic compounds of arsenic in speciation studies. The electrophoretic effluent was introduced through a concentric interface into the mass spectrometer. Make-up liquid was added to enable electric contact at the outlet of the separation capillary and to assist the electronebulization process. After ionization, the ions were analyzed and quantified with an ion-trap detector. Optimization of the coupling conditions (geometry of the concentric interface, composition and flow rate of the sheath liquid, electronebulization and detection conditions) is described. The results show that the geometry of the concentric interface and the positioning of the outlet of the separation capillary have a critical effect on stability and sensitivity. Programming the electronebulization and detection conditions throughout the analysis enabled identification and quantification of the seven arsenic compounds of interest (neutral, and positively or negatively charged species) in less than 20 min at the ppm level. Limits of detection ranged from 0.5 to 3.3 mg L⁻¹, corresponding to amounts injected ranging from 15 to 60 pg. The linear dependence of mass spectrometric response on arsenic concentration was verified for concentrations ranging from 5 to 200 mgL⁻¹. For the two positively charged species, arsenobetaine and arsenocholine, an on-line preconcentration technique (field-amplified sample injection) enabled reduction of the detection limits by approximately one order of magnitude to 110 and 160 μgL⁻¹, respectively.     

Characterization of mixtures of biocidal oligoguanidines by capillary electrophoresis and high-performance liquid chromatography coupled to mass spectrometry

The polycondensation of guanidine hydrochloride and 2,2′-(ethylenedioxy)bis(ethylamine) leads to various types of oligomeric guanidines exhibiting a broad spectrum of biocidal activities. In the present work a reversed-phase high-performance liquid chromatographic method with a gradient consisting of aqueous 0.1% trifluoroacetic acid and acetonitrile as mobile phase has been developed to separate these oligoguanidines according to type and chain length. The combination with electrospray mass spectrometry allowed the identification of the various compounds. By this technique, some structures already suggested in the literature could be confirmed, and several additional oligoguanidines not yet reported could be identified. As a complementary technique, capillary zone electrophoresis was investigated. Best results were obtained with carrier electrolytes consisting of phosphoric acid in water/acetonitrile mixtures. Although the number of peaks that could be separated by the electrophoretic method was considerably lower than in case of the chromatographic method, capillary electrophoresis in combination with UV detection at 195 nm may still be a fast method suitable for quantitation of some of the major compounds and for monitoring the reaction rate during the polycondensation reaction.     

Monomer surface modifications for rapid peptide analysis by capillary electrophoresis and capillary electrochromatography coupled to electrospray ionization-mass spectrometry

In this study, positively charged alkylaminosilyl monomers were used to modify the inner surface of fused silica capillaries, which subsequently were employed in capillary electrophoresis (CE) and capillary electrochromatography (CEC). The obtained surfaces yield a reversed electroosmotic flow (EOF) and have varying carbon chain lengths, that interact with the analytes and give chromatographic retention. The coating procedure is very simple and fast. The performance of the modified capillaries was evaluated regarding pH influence on EOF and chromatographic interactions. The experiments were conducted with UV and mass spectrometry (MS) and applied to the separation of various neuropeptides. The derivatized surfaces showed a linear (R(2) approximately 0.99) pH dependence with isoelectric points (pI) at 8.6-8.8. Rapid separations of peptide standards and a protein digest with efficiencies as high as 5 x 10(5) plates/m were performed.     

Analysis of isoflavones in soy drink by capillary zone electrophoresis coupled with electrospray ionization mass spectrometry

Capillary zone electrophoresis coupled with electrospray ionization mass spectrometry (CZE–ESI-MS) has been applied for the first time for the separation and quantification of isoflavones in soy products. The proposed method was successfully applied to the determination of seven isoflavones, including aglycones and glucosides, in soy drink. The target compounds were the glucosides daidzin and genistin, and the aglycones daidzein, genistein, formononetin, biochanin A and glycitein. During CE separation in positive mode, the analytes were present as anions, and MS detection was carried out in ESI positive-ion mode. To prevent the frequent drops in current and to improve the resolution in the separation of analytes in anionic form, a programmed nebulizing gas pressure (PNP) was applied along the analysis.     

Low-molecular weight protein profiling of genetically modified maize using fast liquid chromatography electrospray ionization and time-of-flight mass spectrometry

In this work, the use of liquid chromatography coupled to electrospray time-of-flight mass spectrometry (LC-TOFMS) has been evaluated for the profiling of relatively low-molecular weight protein species in both genetically modified (GM) and non-GM maize. The proposed approach consisted of a straightforward sample fractionation with different water and ethanol-based buffer solutions followed by separation and detection of the protein species using liquid chromatography with a small particle size (1.8 μm) C(18) column and electrospray-time-of-flight mass spectrometry detection in the positive ionization mode. The fractionation of maize reference material containing different content of transgenic material (from 0 to 5% GM) led to five different fractions (albumins, globulins, zeins, zein-like glutelins, and glutelins), all of them containing different protein species (from 2 to 52 different species in each fraction). Some relevant differences in the quantity and types of protein species were observed in the different fractions of the reference material (with different GM contents) tested, thus revealing the potential use of the proposed approach for fast protein profiling and to detect tentative GMO markers in maize.     

Characterization of deamidated peptide variants by micro-preparative capillary electrophoresis and mass spectrometry

Capillary electrophoresis (CE) was compared with reversed-phase liquid chromatography for its ability to separate native and deamidated peptides. CE is shown to provide superior resolution of these peptides due to its charge-based separation mechanism. Fraction collection performed using a standard CE instrument equipped with a 96-well plate permits subsequent characterization by nanospray mass spectrometric (MS) analysis. Additional in-depth analysis by MS/MS is able to provide the location of the deamidation site based on y-ion mass shifts of 1 Da.     

Micelle to solvent stacking of organic cations in capillary zone electrophoresis with electrospray ionization mass spectrometry

The direction of the effective electrophoretic mobility of small organic cations in micellar electrokinetic chromatography using sodium dodecyl sulphate in a low-pH electrolyte can be reversed in the presence of organic solvent. This effective electrophoretic mobility change is presented here as a new dimension for on-line sample preconcentration of cations in capillary zone electrophoresis (CZE) using a background solution (BGS) modified by an organic solvent. The sample is prepared in a micellar solution without organic solvent. The focusing effect relies on the reversal in the effective electrophoretic mobility at the boundary zone between the micellar matrix and the BGS modified with organic solvent. This on-line sample preconcentration technique, called micelle to solvent stacking (MSS) afforded more than an order of magnitude improvement in concentration sensitivity compared to typical CZE-UV or CZE-electrospray ionization (ESI) MS analysis. The calculated limit of detection (S/N = 3) for pindolol and metoprolol analysed by MSS-CZE-ESI-MS was found to be 0.03 and 0.01 μg/mL, respectively.     

Determination of cobalamins using capillary electrophoresis inductively coupled plasma mass spectrometry

The determination of cobalamins using capillary electrophoresis inductively coupled plasma mass spectrometry (CE-ICP-MS) was investigated. Both capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC) modes of operation were studied. The optimal separation of four cobalamin species (cyanocobalamin, hydroxocobalamin, methylcobalamin, and 5′-deoxyadenosylcobalamin) and a potentially harmful corrinoid analogue (cobinamide dicyanide) was obtained using CZE at a pH of 2.5. Both 20 mM phosphate and 20 mM formate buffers were used with success, although the formate buffer provided improved resolution. The CZE-ICP-MS method was used to quantify cyanocobalamin in a vitamin supplement and the analytical results were in good agreement (±5%) with values obtained by ICP-MS for total Co levels. The solution detection limits for cobalamins using CZE-ICP-MS were approximately 50 ng/ml. MEKC was found to be useful for the screening of vitamin preparations because it provided a rapid means of distinguishing cyanocobalamin (the form most commonly used in vitamin preparations) from free cobalt. The separation of free cobalt and cyanocobalamin using MEKC was achieved in less than 10 min.     

Confirmation of vanadium complex formation using electrospray mass spectrometry and determination of vanadium speciation by sample stacking capillary electrophoresis

Capillary zone electrophoresis (CZE) with UV detection was used to determine vanadium species. Nitrilotriacetic acid (NTA), hydroxyethylethylenediaminetriacetic acid (HEDTA), ethylenediaminetetraacetic acid (EDTA), diethylenetriaminepentaacetic acid (DTPA), ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) and 2,6-pyridinedicarboxylic acid (PDCA) were investigated to determine whether these ligands formed stable anionic complexes with vanadium. Of all the ligands studied HEDTA was the most suitable ligand because it gave the largest UV response with reasonable migration time. Electrospray mass spectrometry (ES-MS) was used to confirm the formation of [VO₂(HEDTA)]²⁻ and [VO(HEDTA)]¹⁻ in solution. An electrolyte containing 25 mM phosphate, 0.25 mM tetradecyltrimethylammonium bromide (TTAB) at pH 5.5 was optimum for the separation of these anionic vanadium complexes. Sample stacking techniques, including large-volume sample stacking (LVSS) and field-amplified sample injection (FASI), were tested to improve the sensitivity. Best sensitivity was obtained using FASI, with detection limits of 0.001 μM, equivalent to 0.4 μg L⁻¹, for [VO₂(HEDTA)]²⁻ and 0.01 μM, equivalent to 3.4 μg L⁻¹ for [VO(HEDTA)]¹⁻. The utility of the method for the speciation of V(IV) and V(V) was demonstrated using ground water samples.     

Complementary middle‐down and intact monoclonal antibody proteoform characterization by capillary zone electrophoresis – mass spectrometry

High‐resolution capillary zone electrophoresis – mass spectrometry (CZE‐MS) has been of increasing interest for the analysis of biopharmaceuticals. In this work, a combination of middle‐down and intact CZE‐MS analyses has been implemented for the characterization of a biotherapeutic monoclonal antibody (mAb) with a variety of post‐translational modifications (PTMs) and glycosylation structures. Middle‐down and intact CZE separations were performed in an acidified methanol‐water background electrolyte on a capillary with a positively charged coating (M7C4I) coupled to an Orbitrap mass spectrometer using a commercial sheathless interface (CESI). Middle‐down analysis of the IdeS‐digested mAb provided characterization of PTMs of digestion fragments. High resolution CZE enabled separation of charge variants corresponding to 2X‐deamidated, 1X‐deamidated, and non‐deamidated forms at baseline resolution. In the course of the middle‐down CZE‐MS analysis, separation of glycoforms of the F_C/2 fragment was accomplished due to hydrodynamic volume differences. Several identified PTMs were confirmed by CZE‐MS². Incorporation of TCEP‐HCl reducing agent in the sample solvent resulted in successful analysis of reduced forms without the need for alkylation. CZE‐MS studies on the intact mAb under denaturing conditions enabled baseline separation of the 2X‐glycosylated, 1X‐glycosylated, and aglycosylated populations as a result of hydrodynamic volume differences. The presence of a trace quantity of dissociated light chain was also detected in the intact protein analysis. Characterization of the mAb under native conditions verified identifications achieved via intact analysis and allowed for quantitative confirmation of proteoforms. Analysis of mAbs using CZE‐MS represents a complementary approach to the more conventional liquid‐chromatography – mass spectrometry‐based approaches.     

Separation techniques hyphenated to electrospray-tandem mass spectrometry in proteomics: capillary electrophoresis versus nanoliquid chromatography

Liquid chromatography (LC) nanoelectrospray-tandem mass spectrometry (MS/MS) is a key technology for the study of proteomics, with the main benefit to the characterization of sensitive peptides from complex mixtures. Capillary electrophoresis coupled to mass spectrometry (MS) has been taken into consideration sporadically due to the highly efficient separation and ability to handle low sample amount, yet classified as being less sensitive with respect to analyte concentration. The limitation in capillary zone electrophoresis (CZE) injection volumes can be overcome by on-line solid-phase extraction (SPE). Such an on-line SPE-CZE system was explored in combination with an ion trap (IT) mass spectrometer. Thus, it was possible to inject more than 100 microL sample solution on to the CZE capillary. Concentration limits of detection as low as 100 amol/microL were demonstrated for a peptide standard. This SPE-CZE-microelectrospray ionization (ESI)-MS/MS setup was compared directly to nanoLC/nanoESI using the same sample of a tryptic digest of bovine serum albumin (BSA) as a reference standard. Measurements were made on one IT mass spectrometer with identical acquisition parameters. Both chromatography systems enabled the separation and detection of low levels of peptides from a mixture of moderate complexity, with most peptides identified using both techniques; however, specific differences were obvious. The nanoLC-MS is about five times more sensitive than the CZE-MS, yet the difference was less pronounced than expected. The CZE-MS technique showed reduced loss of peptides, especially for larger peptides (missed cleavages) and is about four times faster than the nanoLC-MS approach.     

Glossary of terms for separations coupled to mass spectrometry

This document is a glossary of terms for separations coupled to mass spectrometry. It covers gas chromatography/mass spectrometry, liquid chromatography/mass spectrometry, and supercritical fluid chromatography/mass spectrometry and the sample introduction, ionization, and data analysis methods used with these combined techniques.     

Preparative purification of gentamicin components using high-speed counter-current chromatography coupled with electrospray mass spectrometry

We developed a useful and preparative method based on high-speed counter-current chromatography with mass spectrometry (HSCCC/MS) to purify gentamicin C1a, C2/2a and C1 from standard powder. The analytes were purified on the HSCCC model CCC-1000 (multi-layer coil planet centrifuge) with a volatile two-phase solvent system composed of n-butanol/10% aqueous ammonia solution (50:50, v/v) and detected on an LCMS-2020EV quadrupole mass spectrometer fitted with an electrospray ionization (ESI) source system in positive ionization following scan mode (m/z 100-500). The HSCCC/ESI-MS peaks indicated that gentamicin C1a (m/z 450: [M+H](+)), C2/2a (m/z 464: [M+H](+)) and C1 (m/z 478: [M+H](+)) have the peak resolution values of 1.3 and 1.7 from 30 mg of loaded gentamicin powder. The HSCCC yielded 3.9 mg of gentamicin C1a, 12.6 mg of gentamicin C2/2a and 12.0 mg of gentamicin C1. These purified substances were analyzed by LC/MS with scan positive-mode. Based on the LC/MS chromatograms and spectra of the fractions, analytes were estimated to be over 95% pure. These gentamicin isomers of C1a, C2/2a and C1 were evaluated for their antibacterial activities. The overall results indicate that this approach of HSCCC/MS is a powerful technique for the purification of gentamicin components.     

A capillary electrophoresis system with dual capacitively coupled contactless conductivity detection and electrospray ionization tandem mass spectrometry

A commercial system that is comprised of a CE coupled to an ESI triple quadrupole mass spectrometer was equipped with two capacitively coupled contactless conductivity detectors (C⁴Ds). The first C⁴D was positioned inside the original cartridge, and the second C⁴D was positioned as close as possible to the ESI probe entrance by using a 3D‐printed support. The C⁴Ds electropherograms were matched to the ESI‐MS electropherogram by correcting their timescales by the factor L_T/L_D, where L_T and L_D are the total capillary length and the length until the C⁴D, respectively. A general approach for method development supporting the simultaneous conductivity and MS detection is discussed, while application examples are introduced. These examples include the use of C⁴D as a simple device that dismiss the use of an EOF marker, a low‐selectivity detector that continuously provide information about unexpected features of the sample, and even a detector that can be more sensitive than ESI‐MS. The C⁴D used in this setup proved to have a smaller contribution to the peak broadening than ESI‐MS, which allowed that a C⁴D, positioned at 12 cm from the inlet of an 80‐cm‐long capillary, could be used to foresee position and shape of the peaks being formed 6.8 times slower at the ESI‐MS electropherogram.     

Quantification of phosphorus in DNA using capillary electrophoresis hyphenated with inductively coupled plasma mass spectrometry

We have analyzed phosphorus in an enzymatically digested DNA molecule using capillary electrophoresis (CE) hyphenated with inductively coupled plasma mass spectrometry (ICP-MS). The DNA concentration was quantified by the phosphorus value obtained in the CE-ICP-MS analysis. The CE-ICP-MS measurement, for which the interface device AIF-01 equipped three layered nebulizer was adopted, was achieved with limited μL/min nebulizing without loss of sample in the vaporizing chamber. The samples of nucleotides and free phosphate were separated well in the CE-ICP-MS measurement, and the calibration curve (0.1-10μg/mL) of the phosphorus showed a linear (R(2)=0.999) increase in intensity. After digestion of the 100-bp double-strand DNA sample to deoxyribonucleotide-5'-monophosphates (dNMPs) by phosphodiesterase-I, phosphorus was detected by CE-ICP-MS without further purification steps. In this study, we applied two calculation schemes of DNA analysis using a dNMP concentration obtained from CE-ICP-MS. Comparative CE-ICP-MS analysis with DNA digested to dNMPs showed that the assay gave an equal value obtained from the total DNA quantification using fluorescence detection. The detection limits of the DNA sample obtained from these species and phosphorus in nucleotides using CE-ICP-MS were 3.1-26ng/mL. These LOD values were equal to the conventional fluorescence determination of DNA.     

Determination of chlorine species by capillary electrophoresis – mass spectrometry

The applicability of CZE with mass spectrometric detection for the determination of four chlorine species, namely chloride and three stable chlorine oxyanions, was studied. The main aspects of the proper selection of BGE and sheath liquid for the CE‐MS determinations of anions with high mobility were demonstrated, pointing out the importance of pH and the mobility of the anion in the BGE. The possibility of using uncoated fused silica capillary and common electrolytes for the separation was shown and the advantage of using extra pressure at the inlet capillary end was also presented. The linear range was found to be 1–100 µg/mL for ClO₃^? and ClO₄^?, 5–500 µg/mL for ClO₂^?, and 25–500 µg/mL for Cl^?, but the sensitivity can be greatly improved if larger sample volume is injected and electrostacking effect is utilized. The LOD for ClO₃^? in drinking water was 6 ng/mL, when very large sample volume was injected (10 000 mbar·s was applied).     

Determination of egg white lysozyme by on-line coupled capillary isotachophoresis with capillary zone electrophoresis

An on-line coupled capillary isotachophoresis - capillary zone electrophoresis method for the determination of lysozyme in selected food products is described. The optimized electrolyte system consisted of 10 mM NH(4)OH + 20 mM acetic acid (leading electrolyte), 5 mM epsilon -aminocaproic acid +5 mM acetic acid (terminating electrolyte), and 20 mM epsilon -aminocaproic acid +5 mM acetic acid +0.1% m/v hydroxypropylmethylcellulose (background electrolyte). A clear separation of lysozyme from other components of acidic sample extract was achieved within 15 min. Method characteristics, i.e., linearity (0-50 micrograms/mL), accuracy (recovery 96+/-5%), intra-assay (3.8%), quantification limit (1 microgram/ml), and detection limit (0.25 microgram/mL) were determined. Low laboriousness, sufficient sensitivity and low running costs are important attributes of this method. The developed method is suitable for the quantification of the egg content in egg pasta.     

Multiresidue analysis of beta-agonists in bovine and porcine urine,feed and hair using liquid chromatography electrospray ionisation tandem mass spectrometry

The use of β-agonists as growth promoters in cattle breeding is forbidden in many countries for reasons of fair trade and consumer protection. In recent years the use of liquid chromatography (LC) tandem mass spectrometry (MS/MS) has been shown to be the method of choice for the control of β-agonists. In this study an LC-MS/MS multiresidue analysis method is presented for trace analysis of 22 β-agonists. A truly generic concept has been designed based on mixed-mode solid-phase extraction and positive electrospray ionisation LC-MS/MS operated in the multiple reaction monitoring mode. This method allows application to a wide variety of sample matrices such as urine, feed and hair, following minor modifications to the analysis procedure only. The method features fit-for-purpose sensitivity in urine as shown by CCα and CCβ values of less than 0.2 and less than 0.5 μg/l respectively, for all β-agonists studied (terbutaline and reproterol, less than 0.3 and less than 1.0 respectively). Similar but semiquantitative application to feed and hair showed CCβ values of less than 10.0 and less than 5.0 μg/kg, respectively. A further simplification and improvement is demonstrated using Ultra Performance LC (UPLC™) and fast-switching MS/MS. The successful validation of this method following the latest EU requirements and its application to real samples demonstrate that a new versatile tool has been achieved for veterinary control of β-agonists.     

Coupling of capillary electrophoresis with electrospray ionization multiplexing ion mobility spectrometry

In this work, ion mobility spectrometry (IMS) function as a detector and another dimension of separation was coupled with CE to achieve two‐dimensional separation. To improve the performance of hyphenated CE‐IMS instrument, electrospray ionization correlation ion mobility spectrometry is evaluated and compared with traditional signal averaging data acquisition method using tetraalkylammonium bromide compounds. The effect of various parameters on the separation including sample introduction, sheath fluid of CE and drift gas, data acquisition method of IMS were investigated. The experimental result shows that the optimal conditions are as follows: hydrodynamic sample injection method, the electrophoresis voltage is 10 kilo volts, 5 mmol/L ammonium acetate buffer solution containing 80% acetonitrile as both the background electrolyte and the electrospray ionization sheath fluid, the ESI liquid flow rate is 4.5 μL/min, the drift voltage is 10.5 kilo volts, the drift gas temperature is 383 K and the drift gas flow rate is 300 mL/min. Under the above conditions, the mixture standards of seven tetraalkylammoniums can be completely separated within 10 min both by CE and IMS. The linear range was 5–250 μg/mL, with LOD of 0.152, 0.204, 0.277, 0.382, 0.466, 0.623 and 0.892 μg/mL, respectively. Compared with traditional capillary electrophoresis detection methods, the developed CE‐ESI‐IMS method not only provide two sets of qualitative parameters including electrophoresis migration time and ion drift time, ion mobility spectrometer can also provide an additional dimension of separation and could apply to the detection ultra‐violet transparent compounds or none fluorescent compounds.     

A new approach to dynamic deactivation in capillary zone electrophoresis

This paper describes a simple means of obtaining high resolution separations of basic proteins at a pH below their pl. Small amounts of a cationic fluorosurfactant are added to the running buffer. A positively charged wall is thereby obtained which will repel positively charged proteins. The particular chemistry of fluorosurfactants is believed to enhance the efficiency of the deactivation. Examples are presented of the separation of some model proteins, including a human insulin-like growth factor (IGF-I), and a misfolded by-product of the growth factor.