Pulse polarography: IX. Proton diffusion in aqueous sulphate solution

Average diffusion currents, , of the ions H₃O⁺ and HSO₄^? in the system 0.1 M K₂SO₄+H₂SO₄ (pH=3.1?3.8) have been measured at 25°C both with a dropping mercury and a rotating disk electrode, using pulse techniques. The separate diffusion coefficients D_HSO4 and D_H have been estimated fromand it was found that D_H≤61×10^?6 cm²s^?1, which is definitely less than the value calculated when relaxation and (bulk) viscosity effects are taken into account. This is at variance with all the literature D_H values for non-sulphate systems and also with our experimental result D_H=(84.6±0.2)10^?6 cm²s^?1 for the system 0.1 M KCl+HCl, which is about 7% above the value from Onsager's theory. The peculiar behaviour of D_H in a K₂SO₄ solution is attributed to a strong decrease in rotational freedom of water molecules in such a medium.This paper also gives a critical evaluation of the principle of “independent diffusion” in excess neutral electrolyte if more than one species participates in the diffusion process.     

Hydrogen diffusivity in the massive LaNi5 electrode using voltammetry technique

The Randles–Sev?ik relationship has been applied to evaluate atomic hydrogen diffusivity in massive LaNi₅ intermetallic compound. The electrode was cathodically hydrogenated in 6 M KOH solution (22 °C), and then voltammetry measurements were carried out at various, very slow potential scan rates (υ?=?0.01–0.1 mV?·?s^?1). At potentials more noble than the equilibrium potential of the H₂O/H₂ system, the anodic peaks were registered as a consequence of oxidation of hydrogen absorbed in cathodic range. The peak potentials linearly increase with the logarithm of the scan rate with a slope of 0.059 V. The slope testifies to a symmetric charge transfer process with symmetry factor α?=?½. The peak currents linearly increase with the square root of the potential scan rate, and the straight line runs through the origin of the coordinate system. The slope of the I _a ^(peak) ?=?f(υ ^1/2) straight line is a measure of the atomic hydrogen diffusion coefficient. Assuming the hydrogen concentration in the LaNi₅ material after cathodic exposure to be C _0,H?=?0.071 mol?·?cm^?3 (63 % of theoretical value), the hydrogen diffusion coefficient equals D _H?=?2.0?·?10^?9 cm²s^?1. Extrapolation of rectilinear segments of potentiodynamic polarization curves with Tafel slopes of 0.12 V and linear polarization dependencies from voltammetry tests allowed the exchange current densities of the H₂O/H₂ system on the tested material to be determined. The exchange current densities on initially hydrogenated LaNi₅ alloy are close to 1 mA?·?cm^?2, irrespective of the electrode potential scan rate.     

The electrochemical determination of oxygen ion diffusion coefficients in La0.50Sr0.50CoO3−y: Experimental results and related properties

Results of an electrochemical method for the determination of oxygen ion diffusion coefficients D_O^2? in porous pellets of La_0.50Sr_0.50CoO_3?y are presented. Log D_O^2? can be expressed as log D_O^2?=?(2.3±0.2) 10³/T?(6.6±0.6) cm² s^?1. The activation energy E_a for the diffusion process equals 44 kJ mol^?1. Further the related electrochemical measurement and the adjustment of the oxygen deficiency y are described. At 75°C the following empirical Nernst relation between the electrode potential E (vs. a Pt/H₂ (1 atm) electrode in the same solution) and Δy is found: E=627–108 ln (Δy + 0.0054) mV. (Δy=y?y₀; y₀=mole fraction of vacancies at the reversible O₂ potential of 1190 mV). The use of La_0.50Sr_0.50CoO_3?y as a solid solution electrode in practical storage cells seems to be excluded for thermodynamic and kinetic reasons.     

Electrooxidation and Amperometric Detection of Ascorbic Acid at GC Electrode Modified by Electropolymerization of N,N‐Dimethylaniline

The polymer film of N,N‐dimethylaniline (DMA) is deposited on the electrochemically pretreated glassy carbon (GC) electrode by continuous electrooxidation of the monomer. This poly N,N‐dimethylaniline (PDMA) film‐coated electrode can be used as an amperometric sensor of ascorbic acid (AA). The polymer film (thickness (?): 0.3±0.02 μm) having positive charge in its backbone attracts the anionic species AA. Thus, the anodic peak potential (350 mV vs. Ag|AgCl|NaCl_(sat)) for the oxidation of AA at the bare electrode is largely shifted to the negative value (150 mV) at this electrode. The PDMA film‐coated electrode is stable in acidic, alkaline and neutral media and can sense AA at different pH's. The diffusion coefficients of AA in solution (D) and in film (D_s) were estimated by rotating disk electrode voltammetry: D=(5.5±0.1)×10^?6 cm² s^?1 and D_s=(6.3±0.2)×10^?8, (6.0±0.2)×10^?8 and (4.7±0.2)×10^?8 cm² s^?1 for 0.5, 1.5 and 3.0 mM AA, respectively. A permeability of AA through the PDMA film was found to decrease with increasing the concentration of AA in the solution. In the chronoamperometry, the current response for the oxidation of AA at different times elapsed after potential‐step application is linearly increased with the increase in AA concentration in a wide range of its concentration from 25 μM to 1.65 mM. In the hydrodynamic amperometry, a successive addition of 10 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.178 μA cm^?2 μM^?1. So, the fouling of the electrode surface caused by the oxidized product of AA is markedly eliminated at this PDMA film‐coated electrode. A flow injection analysis based on the present electrode was performed to estimate the concentration of vitamin C in fruit juice.     

Electrochemical Responses and Sensitivities of Films Based on Multi-Walled Carbon Nanotubes in Aqueous Solutions

Novel films consisting of multi-walled carbon nanotubes (MWCNTs) were fabricated by means of chemical vapor deposition with decomposition of either acetonitrile (ACN) or benzene (BZ) using ferrocene as catalyst. The electrochemical responses of MWCNT-based films towards the ferrocyanide/ferricyanide, [Fe(CN)₆]^3?/4? redox couple were probed by means of cyclic voltammetry and electrochemical impedance spectroscopy at 25.0?±?0.5?°C. Both MWCNT-based films exhibit Nernstian response towards [Fe(CN)₆]^3?/4? with some slight kinetic differences. Namely, heterogeneous electron transfer rate constants lying in ranges of 2.69?×?10^?2?C1.7?×?10^?3 and 9.0?×?10^?3?C2.6?×?10^?3?cm·s^?1 were obtained at v?=?0.05?V·s^?1 for MWCNT_ACN and MWCNT_BZ, respectively. The detection limit of MWCNT_ACN, estimated to be about 4.70?×?10^?7?mol·L^?1 at v?=?0.05?V·s^?1, tends to become slightly poorer with the increase of the scan rate, namely at v?=?0.10?V·s^?1 the detection limit of 1.70?×?10^?6?mol·L^?1 was determined. Slightly poorer response ability was exhibited by MWCNT_BZ; specifically the detection limits of 1.57?×?10^?6 and 4.35?×?10^?6?mol·L^?1 were determined at v?=?0.05 and v?=?0.10?V·s^?1, respectively. The sensitivities of MWCNT_ACN and MWCNT_BZ towards [Fe(CN)₆]^3?/4? were determined as 1.60?×?10^?7 and 1.51?×?10^?7?A·L·mol^?1·cm^?2, respectively. The excellent electrochemical performance of MWCNT_ACN is attributed to the presence of incorporated nitrogen in the nanotube??s structure.     

Accelerating the electron transfer of choline oxidase using ionic-liquid/NH2-MWCNTs nano-composite

A nano-composite consisting of amine functionalized multi-walled carbon nanotubes and a room temperature ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) was prepared and used for modification of glassy carbon electrode. By immobilizing choline oxidase (ChOx) on the modified electrode, the enzyme direct electron transfer has been achieved. The modified electrode exhibited a pair of well-defined cyclic voltammetric peaks at a formal potential of ?0.395?V versus Ag/AgCl in 0.2?M phosphate buffer solution at pH 7.0. This peak was characteristic of ChOx-FAD/FADH₂ redox couple. The electrochemical parameters such as charge transfer coefficient (??) and apparent heterogeneous electron transfer rate constant (k _s) were estimated to be 0.36 and 2.74?s^?1, respectively. When the enzyme electrode was examined for the detection of choline, a relatively high sensitivity (2.59???A?mM^?1) was obtained. Under the optimized experimental conditions, choline was detected in the concentration range from 6.9?×?10^?3 to 6.7?×?10^?1?mM with a detection limit of 2.7???M. The peak currents of ChOx were reasonably stable and retained 90% of its initial current after a period of 2?months.     

Direct electrochemical behavior of cytochrome c, and its determination on phytic acid modified electrode

Phytic acid (PA) with its unique structure was attached to a glassy carbon electrode (GCE) to form PA/GCE modified electrode which was characterized by electrochemical impedance. The electrochemical behavior of cytochrome c (Cyt c) on the PA/GCE modified electrode was explored by cyclic voltammetry and differential pulse voltammetry. The Cyt c displayed a quasi-reversible redox process on PA modified electrode pH 7.0 phosphate buffer solution with a formal potential (E ^0′) of 57 mV (versus Ag/AgCl). The peak currents were linearly related to the square root of the scan rate in the range of 20–120 mV·s^?1. The electron transfer rate constant was determined to be 12.5 s^?1. The PA/GCE modified electrode was applied to the determination of Cyt c, in the range of 5?×?10^?6 to 3?×?10^?4 M, the currents increase linearly to the Cyt c concentration with a correlation coefficient 0.9981. The detection limit was 1?×?10^?6 M (signal/noise?=?3).     

Electrochemical Behavior of Chloranil Chemically Modified Carbon Paste Electrode. Application to the Electrocatalytic Determination of Ascorbic Acid

A p‐chloranil modified carbon paste electrode was constructed and the electrochemical behavior of this electrode was studied in the aqueous solution with different pH. From the E_1/2–pH diagram for this compound the values of formal potential E^0' and pK_a of some different redox and acid‐base couples depending on the solution pH were estimated. The diffusion coefficient, D, value for p‐chloranil was estimated 1.5×10^?7 cm² s^?1. It has been shown by direct current cyclic voltammetry and double potential step chronoamperometry, that this p‐chloranil incorporated carbon paste electrode, can catalyze the oxidation of ascorbic acid in the aqueous buffered solution. Under the optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 325 mV less positive than that at an unmodified carbon past electrode. The catalytic oxidation peak currents was linearly dependent on the ascorbic acid concentration and a linear calibration curve was obtained in the range of 7×10^?5 M–4×10^?3 M of ascorbic acid with a correlation coefficient of 0.9998. The limit of detection (3σ) was determined as 3.5×10 ^?5 M. This method was used as simple, selective and precise voltammetric method for determination of ascorbic acid in pharmaceutical preparations.     

Poly(2-amino-5-(4-pyridinyl)-1, 3, 4-thiadiazole) film modified electrode for the simultaneous determinations of dopamine, uric acid and nitrite

Poly(2-amino-5-(4-pyridinyl)-1,3,4-thiadiazole) (PAPT) modified glassy carbon electrode (GCE) was fabricated and used for the simultaneous determinations of dopamine (DA), uric acid (UA) and nitrite (NO₂ ^?) in 0.1 mol?L^?1 phosphate buffer solution (PBS, pH 5.0) by using cyclic voltammetry and differential pulse voltammetry (DPV) techniques. The results showed that the PAPT modified GCE (PAPT/GCE) not only exhibited electrocatalytic activities towards the oxidation of DA, UA and NO₂ ^? but also could resolve the overlapped voltammetric signals of DA, UA and NO₂ ^? at bare GCE into three strong and well-defined oxidation peaks with enhanced current responses. The peak potential separations are 130 mV for DA–UA and 380 mV for UA–NO₂ ^? using DPV, which are large enough for the simultaneous determinations of DA, UA and NO₂ ^?. Under the optimal conditions, the anodic peak currents were correspondent linearly to the concentrations of DA, UA and NO₂ ^? in the ranges of 0.95–380 μmol?L^?1, 2.0–1,000 μmol?L^?1 and 2.0–1,200 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. The correlation coefficients were 0.9989, 0.9970 and 0.9968, and the detection limits were 0.2, 0.35 and 0.6 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. In 0.1 mol?L^?1 PBS pH 5.0, the PAPT film exhibited good electrochemical activity, showing a surface-controlled electrode process with the apparent heterogeneous electron transfer rate constant (k _s) of 25.9 s^?1 and the charge–transfer coefficient (α) of 0.49, and thus displayed the features of an electrocatalyst. Due to its high sensitivity, good selectivity and stability, the modified electrode had been successfully applied to the determination of analytes in serum and urine samples.     

Highly selective determination of ascorbic acid,epinephrine, and uric acid by differential pulse voltammetry using poly(Adizol Black B)-modified glassy carbon electrode

A polymerized film of Adizol Black B (ABB) on the surface of glassy carbon (GC) electrode was prepared for the simultaneous determination of ascorbic acid (AA), epinephrine (EP), and uric acid (UA). This new electrode presented an excellent electrocatalytic activity towards the oxidation of AA, EP, and UA by differential pulse voltammetry method. The oxidation peaks of the three compounds were well defined and had the enhanced peak currents. The separation of the oxidation peak potentials for AA–EP and EP–UA were about 180 and 130 mV, respectively. The calibration curves obtained for AA, EP, and UA were in the ranges of 2.0–1,970.0, 0.1–64.0, and 0.1–1,700.0 μmol L^–1, respectively. The detection limits (S/N?=?3) were 0.01, 0.007, and 0.02 μmol L^–1 for AA, EP, and UA, respectively. The diffusion coefficient and the catalytic rate constant for the oxidation reaction of EP at poly(ABB) film-coated GC electrode were calculated as 1.54(±0.10)?×?10^?4 cm² s^?1 and 4.5?×?10³ mol^?1 L s^?1, respectively. The present method was applied to the determination of EP in pharmaceutical, AA in commercially available vitamin C tablet, and UA in urine samples.     

A study of the cathodic reduction of ozone at the rotating disc electrode in acid electrolyte

The cathodic reduction of ozone according to O₃+2H⁺+2e^?→H₂O+O₂ was studied at a rotating disc electrode consisting of bright platinum in 1 M HClO₄ at 20°C. The current-potential curves obtained potentiostatically are determined by slow charge transfer in the range of low polarization (Tafel region) and diffusion as rate controlling step at high overvoltage. From the exchange current densities (i₀), obtained by extrapolation of Tafel lines to the reversible potentials, the heterogeneous rate constant k was evaluated giving an average value of 2.5×10^?7 cm s^?1. Likewise the diffusion coefficient (D_O3=1.7×10^?5 cm² s^?1) was calculated from the limiting currents measured at various partial pressures of ozone and different values of rotation rate. An equation for the total current-polarization curve was developed. The computed curves are in good agreement with the data which were obtained experimentally.     

Electroanalytical Determination of Morpholine as a Corrosion Inhibitor at a Cathodically Pretreated Boron-Doped Diamond Electrode

An electroanalytical method for the determination of morpholine, a corrosion inhibitor, was developed at a cathodically pretreated boron-doped diamond electrode (BDDE). The voltammetric response of morpholine at the BDDE in 0.1?mol L^?1 KCl (pH 10) shows an irreversible oxidation process at approximately 1.3?V vs. Ag/AgCl in 3.0?mol L^?1 KCl. Using cyclic voltammetry, the number of electrons involved in the morpholine electroxidation mechanism was found to be 1. The application of chronoamperometry showed that the apparent diffusion coefficient (D₀) was 2.99?×?10^?6 cm² s^?1. Using square wave voltammetry under the optimized conditions (frequency of 30.0?Hz, pulse amplitude of 100?mV and step potential of 20?mV at pH 10.0), the developed method provided limits of detection and quantification of 2.1 and 6.9?mg L^?1, respectively, with a linear range from 5.0 to 100.0?mg L^?1 (r?=?0.991). Intraday (n?=?10) and interday (two consecutive day) precision values assessed as the relative standard deviation for solutions containing 30.0, 60.0, and 90.0?mg L^?1 of morpholine were from 0.41 to 5.86% and 0.92 to 3.19%, respectively. The feasibility of the method for the interference-free determination of morpholine was verified by the analysis of synthetic boiler water samples containing CaCO₃, Na₂SO₃, Na₃PO_4, FeCl₃, and humic acid as organic matter. In addition, hydrazine was added as a possible interfering compound because of its widespread use in corrosion inhibition. Recovery values from 90.9 to 109.4% were obtained in the synthetic boiler water, thereby attesting to the accuracy of the method.     

Electrochemical behavior of [UO_2Cl_4]~(2-) in 1-ethyl-3-methylimidazolium based ionic liquids

In order to examine the chemical form of uranyl species in 1-ethyl-3-methylimidazolium(EMI) based ionic liquids,UV-visible absorption spectra of solutions prepared by dissolving [EMI] 2 [UO2Cl4] into a mixture of EMICl and EMIBF 4(50:50 mol%) were measured.As a result,it was confirmed that uranyl species in the mixture of EMICl and EMIBF 4 existed as [UO2Cl4]2-.Cyclic voltammograms(CVs) of [UO2Cl4]2-in the mixture were measured at 25 ℃ using a Pt working electrode,a Pt wire counter electrode,and an Ag/Ag + reference electrode(0.01 M AgNO 3,0.1 M tetrabutylammonium perchlorate in acetonitrile) in a glove box under an Ar atmosphere.Peaks corresponding to one redox couple were observed around-1.05 V(Epc) and-0.92 V(Epa) vs.ferrocene/ferrocenium ion(Fc/Fc +).The potential differences between two peaks(Ep) increased from 101 to 152 mV with an increase in the scan rate from 50 to 300 mV s-1,while the(Epc+Epa)/2 value was constant,-0.989 V vs.Fc/Fc + regardless of the scan rate.Furthermore,the diffusion coefficient of [UO2Cl4]2-and the standard rate constant were estimated to be 3.7 × 10-8 cm 2 s-1 and(2.7-2.8) × 10-4 cm s-1 at 25 oC.By using the diffusion coefficient and the standard rate constant,the simulation of CVs was performed based on the reaction,[UO2Cl4]2-+ e = [UO2Cl4]3-.The simulated CVs were found to be consistent with the experimental ones.From these results,it is concluded that [UO2Cl4]2-in the mixture of EMICl and EMIBF 4 is reduced to [UO2Cl4]3-quasi-reversibly at-0.989 V vs.Fc/Fc +.     

Ozone reduction at Nafion modified Au electrode and the measurement of ozone concentration in highly resistive solutions

The mass transport and charge transfer kinetics of ozone reduction at Nafion coated Au electrodes were studied in 0.5 mol/L H2SO4 and highly resistive solutions such as distilled water and tap water. The diffusion coefficient and partition coefficient of ozone in Nafion coating are 1.78×10-6 cm2·s-1 and 2.75 at 25℃ (based on dry state thickness), respectively. The heterogeneous rate constants and Tafel slopes for ozone reduction at bare Au are 4.1×10-6 cm·s-1, 1.0×10-6 cm·s-1 and 181 mV, 207 mV in 0.5 mol/L H2SO4 and distilled water respectively and the corresponding values for Nafion coated Au are 5.5×10-6 cm·s-1, 1.1×10-6 cm·s-1 and 182 mV, 168 mV respectively. The Au microelectrode with 3 μm Nafion coating shows good linearity over the range 0-10 mmol/L ozone in distilled water with sensitivity 61 μA·ppm-1 ·cm-2, detection limit 10 ppb and 95% response time below 5 s at 25℃. The temperature coefficient in range of 11-30℃ is 1.3%.     

Irreversible electrostatic deposition of Prussian blue from colloidal solutions

Prussian blue (PB) can be deposited from colloidal solutions (5.4?×?10^?3?mol_PB?L^?1, 0.01?mol?L^?1 KNO₃) on glassy carbon, either by potential cycling or potentiostatically, provided that the deposition potential is more positive than ?0.2?V vs. Hg/Hg₂Cl₂. Depending on the deposition potential, the PB particles form either a single layer of Everitt??s salt, of PB, or multilayers of Berlin green. Also depending on the electrode potential, the deposition was accompanied by currents which were either only of capacitive nature, or represent the sum of capacitive and faradaic currents. The currents were always limited by the diffusion of the colloidal particles to the electrode surface, i.e., they obeyed the Cottrell equation. The PB layers were characterized by in situ atomic force microscopy.     

New insights on the Cd UPD on Au(111)

The Cd underpotential deposition (UPD) process on Au(111) was analyzed by means of combined electrochemical measurements and in situ scanning tunneling microscopy (STM). In the underpotential range 300?ΔE (mV) ?400, 2D Cd islands are formed on the fcc regions of the Au(111)‐(√3 × 22) reconstructed surface without lifting the reconstruction. At lower underpotentials, the 2D Cd islands grow and, simultaneously, new 2D islands nucleate and coalesce with the previous ones forming a complete condensed Cd monolayer (ML). STM images and long time polarization experiments performed at ΔE = 70 mV demonstrate the formation of an Au? Cd surface alloy. At ΔE = 10 mV, the formation of the complete Cd ML is accompanied by a significant Au? Cd surface alloying and the kinetic results reveal two different solid‐state diffusion processes. The first one, with a diffusion coefficient D₁ = 4 × 10^?17 cm² s^?1, could be ascribed to the mutual diffusion of Au and Cd atoms through a highly distorted (vacancy‐rich) Au? Cd alloy layer. The second and faster diffusion process (D₂ = 7 × 10^?16 cm² s^?1) is associated with the appearance of an additional peak in the anodic stripping curves and could be attributed to the formation of another Cd_zAu_x alloy phase. Copyright © 2008 John Wiley & Sons, Ltd.     

Electrochemical Study on the Interaction of Irinotecan with Calf Thymus Double Stranded DNA

Voltammetric behavior of Irinotecan (CPT‐11) was studied in a phosphate buffer (0.002 mol·L^?1, pH 7.5) solution at the hanging mercury drop electrode (HMDE) using cyclic voltammetry (CV). CPT‐11 showed two irreversible cathodic peaks at ?1.01 V and ?1.09 V which involved two electrons and two protons in each reduction step. In addition, the interaction of Irinotecan with double‐stranded calf thymus DNA (ds‐DNA) was studied by CV at the HMDE employing an irreversible electrochemical equation. As a result of the reaction with ds‐DNA, the reduction peaks related to CPT‐11 were shifted in a negative direction and the peak currents were decreased. The diffusion coefficients of CPT‐11 in the absence (D_f) and presence (D_b) of ds‐DNA were calculated as 2.8×10^?5 cm²·s^?1 and 1.6×10^?5 cm²·s^?1 respectively. The binding constant (K=1.0×10⁴ L·mol^?1), and binding site size (s=0.60) of CPT‐11 interacting with ds‐DNA were obtained simultaneously by non‐linear fit analysis. The results demonstrate that the main interaction mode of CPT‐11 with ds‐DNA is electrostatic.     

The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Study on Dynamic Interfacial Tension of 3‐Dodecyloxy‐2‐hydroxypropyl Trimethyl Ammonium Chloride at n‐Decane/Water Interface

Dynamic interfacial tension (DIT) and interface adsorption kinetics at the n‐decane/water interface of 3‐dodecyloxy‐2‐hydroxypropyl trimethyl ammonium chloride (R₁₂TAC) were measured using spinning drop method. The effects of R_nTAC concentration and temperature on DIT have been investigated, the reason of the change of DIT with time has been discussed. The effective diffusion coefficient, D _a, and the adsorption barrier, ?_a, have been obtained with extended Word‐Tordai equation. The results show that the higher the concentration of surfactants is, and the smaller will be the DIT and the lower will be the curve of the DIT, and the R₁₂TAC solutions follow a mixed diffusion‐activation adsorption mechanism in this investigation. With increase of concentration in bulk solution of R₁₂TAC from 8×10^?4 mol · dm^?3 to 4×10^?3 mol · dm^?3, D _a decreases from 2.02×10^?10 m^?2 · s^?1 to 1.4×10^?11 m^?2 · s^?1 and ? _a increases from 2.60 kJ · mol^?1 to 9.32 kJ · mol^?1, while with increase of temperature from 30°C to 50°C, D _a increases from 2.02×10^?10 m^?2 · s^?1 to 5.86×10^?10 m^?2 · s^?1 and ε_a decreases from 2.60 kJ · mol^?1 to 0.73 kJ · mol^?1. This indicates that the diffusion tendency becomes weak with increase strength of the interaction between surfactant molecules and that the thermo‐motion of molecules favors interface adsorption.