In situ growth stresses during the phase separation of immiscible FeCu thin films

This paper addresses the in situ growth stress evolution and post-growth stress relaxation during the phase separation of immiscible Fe_0.51Cu_0.49 thin films at various in situ deposition temperatures. Each film was sputter-deposited onto a 10 nm Si₃N₄ underlayer that was grown on top of Si [0 0 1] substrate at 25 °C, 145 °C, 205 °C, 265 °C or 325 °C. The thin film stress was measured using a wafer curvature technique. The in situ growth stress increased in compression with increasing substrate temperature. The stress relaxation of the Fe_0.51Cu_0.49 was found to have a linear increase with the inverse grain size for films deposited at temperatures greater than 205 °C. The stress state was correlated to the films’ phase and morphology by X-ray diffraction, (scanning) transmission electron microscopy and atomic force microscopy techniques.     

Multiplication rule of similarity transformations in the coherent state representation and its mapping onto quantum optical generalized ABCD law

We find that classical similarity transformations in the coherent state representation projects onto the similarity transformation operators (STO), these operators constitute a loyal representation of symplectic group. Remarkably, the multiplication rule of the STOs naturally leads to the quantum optical generalized ABCD law, which is the quantum mechanical correspondence of the classical optical ABCD law. Throughout the whole derivation, the technique of integration within an ordered product (IWOP) of operators is employed.     

Formation of vinylidene and vinylene by selective reactivity of Si(1 0 0)2 × 1 towards iso, cis and trans isomers of dichloroethylene

The room temperature (RT) chemisorption of three (iso, cis and trans) isomers of dichloroethylene (DCE) on Si(1 0 0)2 × 1 have been investigated by X-ray photoelectron spectroscopy (XPS) and temperature programmed desorption (TPD). Unlike ethylene, the lack of molecular desorption features in the TPD data effectively rules out the cycloaddition adsorption mechanism for all three isomers. XPS spectra show that cis- and trans-DCE adsorb dissociatively on the 2 × 1 surface in equal proportion as mono-σ bonded 2-chlorovinyl and di-σ bonded vinylene adspecies, which could be produced by dechlorination mechanisms involving the proposed tri-atom π-complex and diradical intermediates, respectively. Acetylene (m/z 26) evolution from 2-chlorovinyl adspecies at 590 K and vinylene at 750 K are also observed for both cis- and trans-DCE, further confirming the common adsorption mechanisms for these geometrical isomers and the relative stabilities of the adspecies. In contrast, only vinylidene adspecies is found for iso-DCE, which indicates that the high ionicity of the CCl₂ group favours the diradical dechlorination mechanism. The single m/z 26 desorption peak for iso-DCE adspecies observed at a higher temperature (780 K) than cis and trans isomers is consistent with the higher adsorption energy of vinylidene than vinylene on Si(1 0 0) obtained in our ab initio calculations. The different relative locations of the Cl atoms in these isomers therefore play a crucial role in controlling the adsorption and thermal evolution on Si(1 0 0)2 × 1. The selective reactivity of the 2 × 1 surface towards these isomers can be used to generate vinylene or vinylidene templates from their corresponding adspecies.     

Removal of lead(II) by adsorption onto Viscumalbum L.: Effect of temperature and equilibrium isotherm analyses

The removal efficiency of Viscumalbum L. from lead containing aqueous solutions was investigated. The effect of adsorbent mass, pH of solution, initial Pb(II) concentration and temperature was investigated using a batch adsorption technique. The optimum pH for Pb(II) adsorption was found as 3.0 for Viscumalbum L. Results were analyzed by the Langmuir, Freundlich, Temkin and Harkins-Jura, equation using linearized correlation coefficient at different temperature. The characteristic parameters for each isotherm have been determined. The Langmuir model agrees very well with experimental data than the other models. According to Langmuir isoterm, the monolayer saturation capacity (Q_o) is 769.23 mg/g at 25 °C. Models and the isotherm constant were evaluated depending on temperature. Thermodynamic parameters such as ΔH^o, ΔS^o and ΔG^o were calculated. The adsorption process was found to be endothermic and spontaneous. The experimental data were analyzed using the first- and the second-order kinetic models. The rate constants of adsorption for both kinetics models have been calculated. The second-order model provides the best correlation of the data.     

Detection of structural and magnetic transitions in La0.67Ba0.23Ca0.1MnO3 using the rf resonance technique

We report radio-frequency (rf) electrodynamics in polycrystalline La_0.67Ba_0.23Ca_0.1MnO₃ as a function of temperature and magnetic field using a home-built LC resonant circuit powered by an integrated chip oscillator. The resonance frequency (f_r) of the oscillator and the power (P) absorbed by the sample are measured simultaneously. The paramagnetic to ferromagnetic phase transition in the absence of an external magnetic field is accompanied by a rapid decrease in both P and f_r around the Curie temperature T_C=300 K. However, much below T_C, the f_r shows a step-like anomaly around 165 K (195 K) while cooling (warming), which we attribute to a structural phase transition from high temperature rhombohedral () to low temperature orthorhombic (Imma) phase. The step-like anomaly in f_r versus T disappears in a field of 300 G. Fractional changes as large as 19% in Δf_r/f_r and 10% in ΔP/P are observed under H=1 kG around T_C. Our study suggests that the rf resonance technique is a versatile tool to study the magnetization dynamics as well as to investigate the structural phase transition in manganites.     

Investigations of the interactions of CO2, O3 and UV light with silver surfaces by in situ IRRAS/QCM and ex situ TOF-SIMS

The characterization of the reactions occurring during the atmospheric corrosion of silver surfaces at the metal-atmosphere interface is of great importance as only the exact knowledge of the degradation mechanisms enables the development of suitable corrosion inhibiting steps. For in situ surface analysis three complementary experimental techniques have been combined in order to study the surface chemistry of silver samples exposed to humidified air, CO₂, ozone (O₃) and ultraviolet (UV) light. In situ infrared reflection absorption spectroscopy (IRRAS) combined with a quartz crystal microbalance (QCM) as well as ex situ time of flight secondary ion mass spectrometry (TOF-SIMS) provide an overall picture of the processes occurring at the metal-atmosphere interface. Investigations were carried out by exposing polycrystalline silver samples to synthetic air containing 50-90% relative humidity (RH) and 250 ppm CO₂. Additionally, the samples were exposed to UV light or O₃ for certain time periods. The formation of the main corrosion products on the sample surfaces, depending on the relative humidity, O₃ content and UV light exposure could be observed in a time resolved way. These investigations reveal the different reaction mechanisms and reaction rates occurring on a silver surface.     

Investigation on densification of Al2O3/B4C ceramic by ab initio calculation and experiment

Compared to experiment, the adsorption energies, bonding properties, and electronic structure of two different Al₂O₃/B₄C bridge sites with seven different Al₂O₃ surfaces are investigated by ab initio periodic density functional theory. The Al₂O₃/B₄C ceramic sintered in Ar is synthesized and measured by XRD and TEM. The calculated results reveal that the densification of O_bridge site of Al₂O₃/B₄C surface is better than that of Al_bridge. The Al₂O₃ (1 1 3)/B₄C with O_bridge is the most favorable and stable. The electronic structure shows that the electron hybridization exists between Al, O atoms and C, B atoms. The results indicate that the calculated results are in good agreement with the experiment.     

ToF-SIMS studies of Bacillus using multivariate analysis with possible identification and taxonomic applications

In this paper we discuss the application of ToF-SIMS with an Au₃⁺ primary ion beam, combined with principal components analysis (PCA) and discriminant function analysis (DFA) for the identification of individual strains of two Bacillus species. The ToF-SIMS PC-DFA methodology is capable of distinguishing bacteria at the strain level based on analysis of surface chemical species. By classifying the data using hierarchical cluster analysis (HCA) we are able to show quantitative separation of species and of these strains. This has taxonomic implications in the areas of rapid identification of pathogenic microbes isolated from the clinic, food and environment.     

Preparation of strontium hexaferrite film by pulsed laser deposition with in situ heating and post annealing

Strontium hexaferrite (SrFe₁₂O₁₉) films have been fabricated by pulsed laser deposition on Si(1 0 0) substrate with Pt(1 1 1) underlayer through in situ and post annealing heat treatments. C-axis perpendicular oriented SrFe₁₂O₁₉ films have been confirmed by X-ray diffraction patterns for both of the in situ heated and post annealed films. The cluster-like single domain structures are recognized by magnetic force microscopy. Higher coercivity in perpendicular direction than that for the in-plane direction shows that the films have perpendicular magnetic anisotropy. High perpendicular coercivity, around 3.8 kOe, has been achieved after post annealing at 500 °C. Higher coercivity of the post annealed SrFe₁₂O₁₉ films was found to be related to nanosized grain of about 50–80 nm.     

Synthesis and characterization of silicon carbonitride films by plasma enhanced chemical vapor deposition (PECVD) using bis(dimethylamino)dimethylsilane (BDMADMS), as membrane for a small molecule gas separation

Silicon carbonitride thin films have been deposited by plasma enhanced chemical vapor deposition (PECVD) from bis(dimethylamino)dimethylsilane (BDMADMS) as a function of X = (BDMADMS/(BDMADMS + NH₃)) between 0.1 and 1, and plasma power P (W) between 100 and 400 W. The microstructure of obtained materials has been studied by SEM, FTIR, EDS, ellipsometrie, and contact angle of water measurements. The structure of the materials is strongly depended on plasma parameters; we can pass from a material rich in carbon to a material rich in nitrogen. Single gas permeation tests have been carried out and we have obtained a helium permeance of about 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ and ideal selectivity of helium over nitrogen of about 20.     

Replication of homologous optical and hydrophobic features by templating wings of butterflies Morpho menelaus

The revealed “Christmas-tree” nanostructures in the cover and ground scales of the butterfly Morpho menelaus are responsible for the observed iridescent blue color and the diffraction pattern of the wings. The aspect ratio of nanostructures in ground scales is more than 5 times higher than that of Morpho peleides cover scales. Inspired by the butterfly, artificial nanostructures are fabricated successfully by templating the scales imbricating in the wings with low-temperature atomic layer deposition (ALD) methods. Through structural characterizations and optical measurements, we reveal that the hybrid structures inherit not only the morphology of the scales with high fidelity but also the homologous optical features including iridescence and diffraction. Besides, water contact angle measurements on both uncoated and coated wings show hydrophobic results. The integration of bio-templates and ALD methods provide a potential route to fabricate the nanostructures with multi-functional features, which may be especially crucial in the applications of innovative functional optical devices.     

Implant assisted-magnetic drug targeting: Comparison of in vitro experiments with theory

Implant assisted-magnetic drug targeting (IA-MDT) was studied both in vitro and theoretically, with extensive comparisons made between model and experiment. Magnetic drug carrier particles (MDCPs) comprised of magnetite encased in a polymer were collected magnetically using a ferromagnetic, coiled, wire stent as the implant and a NdFeB permanent magnet for the applied magnetic field. A 2-D mathematical model with no adjustable parameters was developed and compared to the 3-D experimental results. The effects of the fluid velocity, stent and MDCP properties, and magnetic field strength on the performance of the system were evaluated in terms of the capture efficiency (CE) of the MDCPs. In nearly all cases, the parametric trends predicted by the model were in good agreement with the experimental results: the CE always increased with decreasing velocity, increasing magnetic field strength, increasing MDCP size or magnetite content, or increasing wire size. The only exception was when experiments showed an increase in the CE with an increase in the number of loops in the wire, while the model showed no dependence. The discrepancies between experiment and theory were attributed to phenomena not accounted for by the model, such as 3-D to 2-D geometric and magnetic field orientation differences, and interparticle interactions between the MDCPs that lead to magnetic agglomeration and shearing force effects. Overall, this work showed the effectiveness of a stent-based IA-MDT system through both in vitro experimentation and corroborated theory, with the designs of the ferromagnetic wire and the MDCPs both being paramount to the CE.     

Determination of replacement of some inorganic elements in pulvinus of bean (Phaseolus vulgaris cv. Gina 2004) at chilling temperature by the WDXRF spectroscopic technique

In this study, bean seedlings (Phaseolus vulgaris cv. Gina 2004) were exposed to chilling temperatures until leaves are wrinkled (9 day), that is, showed nyctinastic movement. Pulvinus were subsequently were cut from the leaves. Concentrations of inorganic elements (P, S, Cl, K, Ca, Cu) in the pulvinus were measured by wavelength-dispersive X-ray fluorescence (WDXRF) spectrometry. Results indicated that concentration change (%) was not significant for Ca (0.82) but it was significant for K, P, Cl, S, and especially Cu concentrations (5.4%, 12.8%, 40.2%, 43.7%, 365%, respectively) in pulvinus of plants exposed to chilling temperature compared with control group.We hypothesize here the presence of association between nyctinasti movement brought about by pulvinus at chilling temperature in bean and changes of K, P, Cl, S and especially Cu concentrations measured by WDXRF analysis method.     

L10 FePt thin films with [0 0 1] crystalline growth fabricated by SiO2 addition—rapid thermal annealing and dot patterning of the films

FePt films that have a high degree of order S in their L1₀ structure (S>0.90) and well-defined [0 0 1] crystalline growth perpendicular to the film plane were fabricated on thermally oxidized Si substrates by the addition of an oxide and successive rapid thermal annealing (RTA). The mechanism of L1₀ ordering and [0 0 1] crystalline growth perpendicular to the film plane arising through the oxide addition and RTA process is also discussed. The L1₀ ordering (S>0.90) and the [0 0 1] crystalline growth were achieved by (1) lowering the activation energy due to in-plane tensile stress and the initiation of L1₀ ordering at a low temperature, (2) [0 0 1] crystalline growth through in-plane tensile stress, and (3) enhancement of atomic diffusion via the addition of an oxide and the resultant lowering of the ordering temperature. Effect (1) was observed in the case of SiO₂ addition, effect (2) was generally observed in the case of oxide addition and the RTA process, and effect (3) was prominent in the case of ZnO addition. With the addition of ZnO, the L1₀ ordering started at below 400 °C and was completed at 500 °C. Finally, dot patterns were successfully fabricated down to a diameter of 15 nm using electron beam lithography, and the magnetic state of the dot pattern was observed by magnetic force microscopy.     

Annihilation and creation of rotating waves by a local light pulse in a protoplasmic droplet of the Physarum plasmodium

Pattern dynamics plays a fundamental role in biological functions from cell to organ in living systems, and the appearance of rotating waves can lead to pathological situations. Basic dynamics of rotating waves of contraction-relaxation activity under local perturbation is studied in a newly developed protoplasmic droplet of the Physarum plasmodium. A light pulse is applied by irradiating circularly a quarter of the droplet showing a single rotating wave. The oscillation pattern changes abruptly only when the irradiation is applied at a part of the droplet near the maximal contraction. The abrupt changes are as follows: the rotating wave disappears or is displaced when the irradiation area is very close to the center of the rotating wave, while new rotating waves are created when the irradiation area is far from the center of the rotating wave. These results support the hypothesis that the phase response curve has a discontinuous change (type 0 resetting) from delay to advance around the maximal contraction. The significance of the results is discussed in relation to “vulnerability” in excitable media and biological systems in general.     

Direct micropatterning of high dielectric BaTiO3 films by laser-induced pyrolysis with a nano-crystalline seeding technique

A direct patterning method of dielectric BaTiO₃ (BT) films is proposed, which applies laser-induced pyrolysis in combination with nano-crystalline seeding technique. A precursor solution of a BT complex alkoxide containing BT nano-crystalline particles with polyvinylpyrollidone (PVP) as dispersion stabilizer was spin-coated on Pt substrate. An Ar⁺ laser beam was focused and scanned on spin-coated BT films, which induced pyrolysis and crystallization of the films with spatial selectivity. Micropatterns were obtained by striping laser-unirradiated regions on the films with HCl aqueous solution. Raman spectra of the micropattern confirmed that the structures were tetragonal crystalline BT. Clear micropatterns with a line width of ca. 3 μm and an interval of 5 μm were formed at PVP concentrations of 25 and 50 kg/m³. The dielectric constant and dissipation factor of the film fabricated at a laser energy density of 27 MW/cm² and a scanning speed of 25 μm/s attained 76.2 and 0.07, respectively, for a measurement frequency of 100 kHz.     

Study of interaction of butyl p-hydroxybenzoate with human serum albumin by molecular modeling and multi-spectroscopic method

Study of the interaction between butyl p-hydroxybenzoate (butoben) and human serum albumin (HSA) has been performed by molecular modeling and multi-spectroscopic method. The interaction mechanism was predicted through molecular modeling first, then the binding parameters were confirmed using a series of spectroscopic methods, including fluorescence spectroscopy, UV-visible absorbance spectroscopy, circular dichroism (CD) spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. The thermodynamic parameters of the reaction, standard enthalpy ΔH⁰ and entropy ΔS⁰, have been calculated to be −29.52 kJ mol⁻¹ and −24.23 J mol⁻¹ K⁻¹, respectively, according to the Van’t Hoff equation, which suggests the van der Waals force and hydrogen bonds are the predominant intermolecular forces in stabilizing the butoben-HSA complex. Results obtained by spectroscopic methods are consistent with that of the molecular modeling study. In addition, alteration of secondary structure of HSA in the presence of butoben was evaluated using the data obtained from UV-visible absorbance, CD and FT-IR spectroscopies.     

Surface structure analysis of metal adsorbed Si(1 1 1) surfaces by Patterson function with LEED I-V curves

Wu and Tong proposed the calculation method of Patterson function obtained directly from the LEED I-V curves which shows the relative position of surface atoms as an image. We have made the calculation program of Patterson function and applied to the structural analysis of the Si(1 1 1)1 × 1-Fe surface. Surface structure was able to be expressed almost correctly by the Patterson function obtained from the theoretical I-V curves for the model structure. In the Patterson function obtained from the experimental I-V curves, the locational relation between the atoms of subsurface layer was in agreement with the CsCl type structure. More over, because the faint peak, by which we can distinguish the model, can be seen, it seems that the model B8 is preferable to the model A8. This result is consistent with the model shown by Walter et al.