Evolution of magnetic order in mechanically alloyed Al–1 at%Fe

The evolution of ferromagnetic order in high-energy ball-milled Al–1 at% Fe before the onset of a considerable Fe–Al solid solution phase has been investigated using ⁵⁷Fe Mössbauer and bulk magnetization studies. The unmilled sample does not exhibit bulk magnetic properties and an onset of bulk magnetization is observed only after 30 min of milling, when the grain size becomes comparable to the ferromagnetic exchange length. The Curie temperatures of all the samples are less than that of pure iron. The reduction in grain size is accompanied by an increase in coercivity and reduced remanence and a decrease in T_C. The effective magnetic moment per iron atom decreases with the development of a non-magnetic, Al-rich Fe–Al solution on longer milling. The clustering of Fe at grain boundaries is responsible for the observed bulk magnetic ordering. The systematic variation of the magnetic properties has been qualitatively correlated with the evolution of microstructure, reduction in grain size and enhanced inter-granular exchange coupling.     

Magnetic,electrical transport and electron spin resonance studies of Fe-doped manganite LaMn0.7Fe0.3O3+δ

We have investigated the magnetic, electrical transport and electron spin resonance (ESR) properties of polycrystalline Fe-doped manganite LaMn_0.7Fe_0.3O_3+δ prepared by sol–gel method. A typical cluster-glass feature is presented by DC magnetization and AC susceptibility measurements and a sharp but shallow memory effect was observed. Symmetrical Lorentzian lines of the Mn/Fe spectra were detected above 120 K, where the sample is a paramagnetic (PM) insulator. When the temperature decreases from 120 K, magnetic clusters contributed from ferromagnetic (FM) interaction between Mn³⁺ and Mn³⁺/Fe³⁺ ions develop and coexist with PM phase. At lower temperature, these FM clusters compete with antiferromagnetic (AFM) ones between Fe³⁺ ions, which are associated with a distinct field-cooled (FC) effect in characteristic of cluster-glass state.     

Properties of Fe–Ga based powders prepared by mechanical alloying

Alloys of Fe–Ga with starting compositions of 17, 19, 21, 23, and 25 at% Ga and Fe₈₁Ga₁₇Z₂ (Z=Si, Sn) have been prepared by mechanical alloying. Samples were milled in a SPEX Model 8000 mill with a ball to sample weight ratio of about 4:1. Phase formation as a function of milling time has been investigated for the 19 at% Ga sample and suggests that milling times of 12 h produce fully alloyed samples. Alloys have been studied by electron microprobe, X-ray diffraction, vibrating sample magnetometery and ⁵⁷Fe Mössbauer effect spectroscopy. Fully milled powders have measured compositions of Fe_100−xGa_x with x=15.7, 17.0, 19.0, 22.4, and 24.0 and Fe_83.1Ga_15.2Z_1.7 (for both Z=Si and Sn). X-ray diffraction showed the presence of a disordered bcc phase with no indication of an ordered D0₃ phase. However, the latter is difficult to observe with X-ray diffraction because of the low intensity of the fcc superlattice peaks. A bimodal Fe hyperfine field distribution as obtained from Mössbauer effect spectra indicated the presence of two discrete Fe environments. The results suggested a lower degree of Ga clustering than has been previously observed in Fe–Ga alloys, of similar composition, prepared by melt spinning. The microstructure is similar to that of Fe–Ga thin films prepared by combinatorial sputtering. Some samples have also been studied after annealing at 800 °C for 8 h. No changes were observed in X-ray diffraction patterns after annealing. However, Mössbauer effect studies show the formation of D0₃ and L1₂ order in annealed samples analogous to the phases observed in melt spun ribbons of similar composition.     

Magnetic properties of anisotropic Sm–Fe–N bulk magnets produced by spark plasma sintering method

Sm–Fe–N powders were consolidated into bulk materials by the spark plasma sintering (SPS) method. Although partial decomposition of the Sm₂Fe₁₇N₃ phase was noted in the magnets, the decomposition was reduced by the addition of a small amount of Zn powder to the Sm–Fe–N powder. The anisotropic Sm–Fe–N magnet obtained from a mixture of Sm–Fe–N and Zn powders exhibited a high remanence of 0.90 T with a coercivity of 0.54 MA m⁻¹.     

Giant Faraday rotation in Fe–ZnSe granular films

The giant magneto-optical Faraday effect (giant Faraday rotation) of ferromagnetic metal–semiconductor matrix Fe–ZnSe granular films prepared by radio frequency sputtering is studied. The result shows that the Faraday rotation angle θ_F value of the granular films sample with Fe volume fraction x=35% is of the order of 10⁵ °/cm at room temperature. Temperature dependence of the θ_F of Fe_0.35(ZnSe)_0.65 granular films shows that θ_F value, below 150 K, increases rapidly with the decrease of the temperature, and when T=10 K θ_F value is 6×10⁵ °/cm. Through the study of the structure and dependence of magnetic properties on temperature, it has been found that the remarkable increase of the θ_F value of Fe_0.35(ZnSe)_0.65 granular films below 150 K seems to arise from the sp–d exchange interaction inside the granular films.     

Surface analysis of heat-treated Mong Hsu rubies

Mong Hsu rubies have been heat treated in air at 1100, 1200, 1300, 1400, 1500 and 1600 °C. Their visual appearance and surface analysis (XPS) after each stage of heating have been monitored. The characteristic blue core regions of untreated ruby become slightly faded at 1100 °C and completely disappear at temperatures above 1500 °C. Trace amounts of Na, Ca, Si and Fe were found on the surface of untreated stones. Ti was first detected after heating to 1100 °C. Plots of detected surface concentrations of elements versus temperature show that the highest concentration of Fe occurred at 1300 °C while surface concentrations of Ti appeared to show two maxima near 1300 and 1500 °C. The results suggest that both the changing oxidation state of Fe²⁺ to Fe³⁺ and the diffusion of the Fe and Ti ions with temperature are responsible for the color changes through decreasing Fe²⁺ to Ti⁴⁺ charge transfer.     

Graphite nanosheets doped with Fe, Ni, and N, synthesized in one step, and their unique magnetic performance

Graphite nanosheets (GNs) doped with N, Fe, or Ni were synthesized by pyrolysis of metal tetrapyridinoporphyrazine (MPTpz, M=Fe²⁺, and Ni²⁺) and a mixture of MPTpzs in a chemical vapor deposition furnace. The products obtained were characterized by scanning and transmission electron microscopy, and X-ray photoelectron spectroscopy. The magnetic properties of the GNs obtained were investigated at room temperature using a vibrating sample magnetometer with an applied field of −10 000-10 000 Gs. The results show the GNs obtained are terrace-like and ultra-thin, with very high aspect ratio. Fe, Ni and N atoms have been doped to the GNs successfully. There are two types of N atom that are introduced into pure carbon systems: pyrinidic and graphitic N atoms. The GNs obtained exhibit ferromagnetic behavior at room temperature. Sample S1, obtained by pyrolysis of a mixture of MPTpzs (M=Fe²⁺ and Ni²⁺), have the highest coercivity force. The saturation magnetization (M_s), remanent magnetization (M_r), and coercivity (H_c) values of sample S1 are 24.51 emu g⁻¹, 3.95 emu g⁻¹, and 207.34 Gs, respectively.     

Mössbauer spectroscopy as a probe of magnetic states in La0.5Ca0.5FeO3−δ perovskite

Charge disproportionation in La_0.5Ca_0.5FeO_3−δ perovskite has been detected by zero-field Mössbauer spectra from 20 K to room temperature. On the basis of the parameters of center shifts and hyperfine fields, Mössbauer spectra identified that the iron ionic states are Fe³⁺ and Fe⁵⁺ below 150 K, Fe³⁺, Fe⁴⁺ and Fe⁵⁺ in the intermediate temperature region, as well as Fe³⁺ and Fe⁴⁺ above 220 K. At low temperatures, the system exhibits a cluster-glass-like state resulting from competition between antiferromagnetic interaction of Fe³⁺–Fe³⁺ and ferromagnetic interaction of Fe³⁺–Fe⁵⁺.     

Influence of Fe-doping on the structural,optical and magnetic properties of ZnO nanoparticles

Zn_1–xFe_xO (x=0–0.05) nanoparticles were synthesized without a catalyst by a two-step method. Fe was doped into ZnO by a source of metallic Fe sheets in a solid–liquid system at 80 °C, and the Zn_1−xFe_xO nanoparticles were obtained by annealing at 300 °C. X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy were used to characterize the structural properties of the as-grown Zn_1−xFe_xO. The optical properties were determined by Infrared and Ultraviolet–visible spectroscopy. The results confirm that the crystallinity of the ZnO is deteriorated due to Fe-doping. XPS results show that there is a mixture of Fe⁰⁺ and the Fe³⁺ in the representative Zn_0.95Fe_0.05O sample. The optical band gap of Zn_1−xFe_xO is enhanced with increasing of Fe-doping. Room temperature ferromagnetism was observed in all the Fe-doped ZnO samples.     

Extended X-ray absorption fine structure (EXAFS) and X-ray absorption near-edge structure (XANES) study of melt-spun Fe85Ga15 ribbons

The local structure in melt-spun Fe₈₅Ga₁₅ ribbons with a width ∼3 mm and thickness ∼60 μm produced in argon atmosphere was studied by analyzing EXAFS and XANES data. The following results were obtained: Ga–Ga bonds were not detected excluding the tendency to form clusters of Ga atoms; Ga substitutes Fe creating a local strain of about +1% on the first shell Fe–Ga bond, whereas on the second Fe–Ga shell strain quickly relaxes down to +0.3%; XANES spectra are compatible with a random substitution of Fe atoms by Ga atoms in the A2 structure. From the AFM investigation, we observed that at the surface (free side) of the ribbon the particles are elongated along the ribbon (∼2 μm×∼5 μm) and each particle is formed by small grains of average size of 200 nm.     

Magnetic properties of amorphous Ge–Fe thin films

Thin films of Ge_100−xFe_x (x in at%) alloys, fabricated by thermal co-evaporation, have an amorphous structure at compositions x<∼40, although an unidentified crystalline phase with an FCC symmetry also exists at low Fe content. Magnetization versus temperature curves show that saturation magnetization is non-zero (1 to 2.5 emu/cm³) and remains nearly unchanged up to the highest measured temperature of 350 K. Magnetic hysteresis loops at room temperature show a typical ferromagnetic shape, complete saturation occurring by 1–2 kOe. These results may indicate ferromagnetic ordering at room temperature. No definite tendency is observed in the compositional dependence of saturation magnetization.     

Synthesis and characterization of nanostructured strontium hexaferrite thin films by the sol–gel method

Nanostructured single phase strontium hexaferrite, SrFe₁₂O₁₉, thin films have been synthesized on the (100) silicon substrate using a spin coating sol–gel process. The thin films with various Fe/Sr molar ratios of 8–12 were calcined at different temperatures from 500 to 900 °C. The composition, microstructure and magnetic properties of the SrFe₁₂O₁₉ thin films were characterized using Fourier transform infrared spectroscopy, differential thermal analysis, thermogravimetry, X-ray diffraction, electron microscopy and vibrating sample magnetometer. The results showed that the optimum molar ratio for Fe/Sr was 10 at which the lowest calcination temperature to obtain the single phase strontium hexaferrite thin film was 800 °C. The magnetic measurements revealed that the sample with Fe/Sr molar ratio of 10, exhibited higher saturation magnetization (267.5 emu/cm³) and coercivity (4290 Oe) in comparison with those synthesized under other Fe/Sr molar ratios.     

The influence of temperature on magnetic and microwave absorption properties of Fe/graphite oxide nanocomposites

Fe/graphite oxide nanocomposites were prepared by inserting Fe³⁺ into layers of graphite oxide and then reducing Fe³⁺/graphite oxide compound at different reduced reaction temperatures in H₂. The composition, crystal structure, magnetic and microwave absorption properties of Fe/graphite oxide nanocomposites were investigated using elemental analysis, transmission electron microscope (TEM), X-ray diffraction (XRD), magnetic hysteresis curve and electromagnetic parameter analysis. The results show that the densities of samples are 2.43–2.47 g/cm³ and the nanocomposites are soft magnetic materials. The optimum reduced reaction temperature for preparing Fe/graphite oxide nanocomposites is 600 °C. With the increase of the thickness of the sample, the matching frequency tends to shift to the lower frequency region, and theoretical reflection loss becomes less at the matching frequency. Microwave absorption property of Fe/graphite oxide nanocomposites prepared at 600  °C (FeGO600) is the best. When the thickness is 1 mm, the maximum theoretical reflection loss of FeGO600 is −9 dB and the frequency region in which the maximum reflection loss is more than −6.0 dB is 11–18 GHz. In conclusion, FeGO600 is a good candidate for microwave absorbent due to its low density, wide frequency region for microwave absorption and large reflection loss.     

Composition, structure and morphology of oxide layers formed on austenitic stainless steel by oxygen plasma immersion ion implantation

Oxygen ions were implanted in to austenitic stainless steel by plasma immersion ion implantation at 400 °C. The implanted samples were characterized by XPS, GIXRD, micro-Raman, AFM, optical and scanning electron microscopies. XPS studies showed the presence of Fe in elemental, as Fe²⁺ in oxide form and as Fe³⁺ in the form of oxyhydroxides in the substrate. Iron was present in the oxidation states of Fe²⁺ and Fe³⁺ in the implanted samples. Cr and Mn were present as Cr³⁺ and Mn²⁺, respectively, in both the substrate and implanted samples. Nickel remained unaffected by implantation. GIXRD and micro-Raman studies showed the oxide to be a mixture of spinel and corundum structures. Optical and AFM images showed an island structure on underlying oxide. This island structure was preserved at different thicknesses. Further, near the grain boundaries more oxide growth was found. This is explained on the basis of faster diffusion of oxygen in the grain boundary regions. Measurement of total hemispherical optical aborptance, α and emittance, ? of the implanted sample show that it has good solar selective properties.     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Possible origin of room-temperature ferromagnetism in undoped GaN epilayers implanted with Mn ions

Manganese ions were implanted into unintentionally doped GaN epilayers grown by metal organic chemical vapor deposition (MOCVD). The (Ga,Mn)N and Ga_xMn_y phases were formed after Mn-implanted undoped GaN epilayers annealed at 700 and 800 °C. The samples showed ferromagnetic behavior at room temperature with the highest magnetization obtained in the sample annealed at 800 °C. Ferromagnetic signal reduces as annealing temperature increased above 900 °C. It is believed that the room-temperature ferromagnetic property of Mn-implanted undoped GaN epilayers are mainly from (Ga_,Mn)N. The Ga_xMn_y phases play a critical role in providing holes and also contribute to increasing the ferromagnetic property.     

Room temperature magnetism of Fe doped CdS nanocrystals

Undoped and Fe doped CdS nanocrystals with Fe content of 2–5 at% of average crystallite size 1.2–2 nm have been obtained using chemical co-precipitation method with 2-mercaptoethonal as capping agent at 80 °C. X-ray diffraction (XRD) results showed that the undoped CdS nanocrystals were in mixed phase of cubic and hexagonal, where as the doped CdS nanocrystals were in hexagonal phase. Room-temperature ferromagnetism has been observed in Fe-doped CdS nanocrystals. Magnetic studies indicated diamagnetism in undoped, ferromagnetism in lightly doped (2 and 3 at%) and paramagnetism in samples of higher Fe content (4 and 5 at%). The substitutional incorporation of Fe³⁺ ion in Cd²⁺ sites was reflected in structural and electron paramagnetic resonance (EPR) measurements. Isolated as well as interacting Fe³⁺ ions are observed in EPR.     

Relationship between structural and magnetic properties in (Ti,Fe)O2 powders obtained by mechanical milling

Fe-doped TiO₂ samples with different Fe content were prepared by mechanical alloying starting from TiO₂ rutile and FeO. The samples were structurally and magnetically characterized by XRD, Mössbauer spectroscopy, X-ray absorption spectroscopy (XAS), AC-susceptibility and magnetization measurements. XAS results showed that Fe ions were incorporated into the rutile phase with oxygen coordination that was lower than that expected in this phase. The oxygen coordination number decreased with the increase of Fe²⁺ ions such as it was previously found in the milled samples of TiO₂ doped with hematite. The RT Mössbauer spectra were reproduced using two paramagnetic interactions, one corresponding to Fe²⁺ (δ∼0.87 mm/s) and the other to Fe³⁺ (δ∼0.31 mm/s). Magnetometry measurements showed the presence of paramagnetic and ferromagnetic-like interactions at room temperature. Although saturation and coercivity of the ferromagnetic phase increased with iron, the effective magnetic moment per iron atom decreased, probably due to the precipitation of Fe rich antiferromagnetic structures.     

The important role of Mn in the room-temperature ferromagnetism of Mn-doped GaN films

Mn-doped GaN films (Ga_1−xMn_xN) were grown on sapphire (0 0 0 1) using Laser assisted Molecular Beam Epitaxy (LMBE). High-quality nanocrystalline Ga_1−xMn_xN films with different Mn concentration were then obtained by thermal annealing treatment for 30 min in the ammonia atmosphere. Mn ions were incorporated into the wurtzite structure of the host lattice by substituting the Ga sites with Mn³⁺ due to the thermal treatment. Mn³⁺, which is confirmed by XPS analysis, is believed to be the decisive factor in the origin of room-temperature ferromagnetism. The better room-temperature ferromagnetism is given with the higher Mn³⁺ concentration. The bound magnetic polarons (BMP) theory can be used to prove our room-temperature ferromagnetic properties. The film with the maximum concentration of Mn³⁺ presents strongest ferromagnetic signal at annealing temperature 950 °C. Higher annealing temperature (such as 1150 °C) is not proper because of the second phase Mn_xGa_y formation.     

Synthesis and characterization of lithium ferrite by oxalate precursor route

Nanocrystalline lithium ferrite (LiFe₅O₈) powders have been synthesized by oxalate precursor route. The effects of Fe³⁺/Li⁺ mole ratio, and annealing temperature on the formation, crystalline size, morphology and magnetic properties were systematically studied. The Fe³⁺/Li⁺ mole ratio was controlled from 5 to 3.33 while the annealing temperature was controlled from 600 to 1100 °C. The resultant powders were investigated by differential thermal analyzer (DTA), X-ray diffractometer (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). DTA results showed that LiFe₅O₈ phase started to form at around 520 °C. XRD indicated that LiFe₅O₈ phase always contained α-Fe₂O₃ impurity and the hematite phase formation increased by increasing the annealing temperature ?850 °C for different Fe³⁺/Li⁺ mole ratios 5, 4.55 and 3.85. Moreover, lithium ferrite phase was formed with high conversion percentage at critical annealing temperature 750–800 °C. Single well crystalline LiFe₅O₈ phase was obtained at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperatures from 800 to 1000 °C. Maximum saturation magnetization (68.7 emu/g) was achieved for the formed lithium ferrite phase at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperature 1000 °C.