The influence of composition and field annealing on magnetic properties of FeCo-based amorphous and nanocrystalline alloys

We report the influence of composition and very high transverse field annealing on the magnetic properties and structure of four FeCo-based amorphous and nanocrystalline alloys. The compositions (Fe₅₀Co₅₀)₈₉Zr₇B₄ and (Fe₆₅Co₃₅)₈₉Zr₇B₄ were investigated changing the Fe:Co ratio from 50:50 to 65:35. (Fe₅₀Co₅₀)₈₅Zr₂Nb₄B_8.5 was chosen to investigate Nb substitution for Zr in an FeCo-based alloy. This substitution is shown to increase the magnetostrictive constant, _λS${\lambda }_{\mathrm{S}}$, of the nanocrystalline alloy from 36×10⁻⁶ to 54×10⁻⁶. The composition (Fe₆₅Co₃₅)₈₄Cr₅Zr₇B₄ was studied to investigate the influence of Cr on intergranular coupling across the amorphous matrix. Samples of each composition were annealed in the amorphous state at 300 °C and in the nanocrystalline state at 600 °C. Field annealing was performed in 17 T transverse field in an inert atmosphere. Frequency-dependent magnetic properties were measured with an automatic recording hysteresisgraph. Static magnetic properties were measured with a vibrating sample magnetometer. The mass-specific power loss of the alloys decreased with field annealing in both the nanocrystalline and amorphous states for some frequency and induction combinations. Furthermore, the hysteresis loops are sheared after field annealing, indicating a transverse magnetic anisotropy. The nanocrystalline (Fe₅₀Co₅₀)₈₅Zr₂Nb₄B_8.5 composition has a lower relative permeability than the other compositions.     

First-order-reversal-curve analysis of Pr-Fe-B-based nanocomposites

Ribbons of nominal composition (Pr_9.5Fe_84.5B₆)_0.96Cr_0.01(TiC)_0.03 were produced by arc-melting and melt-spinning the alloys on a Cu wheel. X-ray diffraction reveals two main phases, one based upon α-Fe and the other upon Pr₂Fe₁₄B. The ribbons show exchange spring behavior with H_c=12.5 kOe and (BH)_max=13.6 MGOe when these two phases are well coupled. Transmission electron microscopy revealed that the coupled behavior is observed when the microstructure consists predominantly of α-Fe grains (diameter ∼100 nm.) surrounded by hard material containing Pr₂Fe₁₄B. A first-order-reversal-curve (FORC) analysis was performed for both a well-coupled sample and a partially-coupled sample. The FORC diagrams show two strong peaks for both the partially-coupled sample and for the well-coupled material. In both cases, the localization of the FORC probability suggests demagnetizing interactions between particles. Switching field distributions were calculated and are consistent with the sample microstructure.     

Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Soft magnetic properties of NiFe compacted powder alloys

It is known that Ni–Fe based alloys (permalloys) are important soft magnetic materials, which have been widely applied in the field of electronic devices and industry. The most suitable permalloys for application exhibit low value of coercivity and magnetostriction (for about 80 at% Ni), high saturation magnetic induction (for about 50 at% Ni), higher electrical resistivity (for about 35 at% Ni). The aim of this work was to investigate the structure and magnetic properties of _Ni81Fe19${\mathrm{Ni}}_{81}{\mathrm{Fe}}_{19}$ (wt%) compacted powder material in the form of small cylinders.     

Study of the magnetic properties of the permanent magnets by Mössbauer spectroscopy

This paper presents methods that can be used in order to determine the relative remanent magnetization and uniaxial magnetic anisotropy constant of particles in powder-based permanent magnets using Mössbauer spectroscopy. The methods were verified on the permanent magnet barium ferrite.     

Size effect on the magnetism of nanocrystalline Ni films at ambient temperature

Size effect on the magnetization and the coercivity of nanocrystalline Ni films has been examined at room temperature. Agreement between modeling predictions and measurements reveals that the size-suppressed magnetization results from the drop of spin-spin exchange energy due to the coordination number (CN) imperfection of atoms near the surface edges, and that the size-enhanced coercivity arises from intergrain interaction that is proportional to the inverse of particle size. Findings herewith and reported previously on the size-induced lattice contraction and Curie temperature suppression evidence the significance of atomic CN imperfection on the unusual behavior of a ferromagnetic nanosolid.     

Magnetic and microstructural characterizations of CoFe and CoFeB nanowires

Magnetic and microstructural characterizations of cobalt-rich CoFe and CoFeB nanowires fabricated in commercially available alumite templates were investigated. The modifications in magnetic and microstructural behaviors of crystalline CoFe and amorphous CoFeB nanowires were observed after magnetic field annealing and reannealing of the samples.     

Depth dependence of Néel wall pinning on amorphous CoxSi1−x films with diluted arrays of elliptical antidots

Diluted arrays of elliptical antidots have been fabricated by optical lithography, electron beam lithography and plasma etching on amorphous Co₇₄Si₂₆ magnetic films with a well-defined uniaxial anisotropy. The magnetic behavior of two identical antidot arrays but with different hole depth in comparison with film thickness has been studied by transverse magneto-optical Kerr effect. Significant differences appear in the coercivity depending on whether the magnetic film is completely perforated or not, indicating a much more effective domain wall pinning process when the depth of the holes is smaller than the magnetic film thickness.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

Structural relaxation,crystallization and improvement of magnetic properties in FeXSiB (X=Cr,Nb)-type amorphous alloys

In the present paper, the influence of Nb and Cr on intensity of structural relaxation, crystallization processes, electric and magnetic properties in the Fe₇₆Nb₂Si₁₃B₉, Fe₇₆Cr₂Si₁₃B₉ and Fe₇₆Nb₁Cr₁Si₁₃B₉ alloys were investigated. It was shown that the improvement of magnetic permeability caused by a suitable annealing is a thermally activated process. Activation energy of this process is found to be of the order of 1 eV. Cr as an alloying addition to the Fe–Si–B alloy does not change the 1 h optimization annealing temperature and causes an increase of its efficiency. Nb as an alloying addition causes an increase of the 1 h optimization annealing temperature, and also the temperature of the first step of crystallization.     

Contribution of magnetostatic interaction to magnetization reversal of Fe3Pt nanowires arrays: A micromagnetic simulation

Using the micromagnetic simulations, we have investigated the magnetization reversal and magnetostatic interaction of Fe₃Pt nanowires arrays with wire diameters lower than 40 nm. By changing the number of interacting nanowires, N, interwire distance, a, and wire diameter, D, the effects of magnetostatic interaction on coercivity and remanence are investigated in detail. According to the simulated results, the contribution to the stray field induced by surface perpendicular magnetization at the end of wires is established.     

Permeability-frequency spectra of (Fe1−xcox)73.5Cu1Nb3Si13.5B9 nanocrystalline alloys under different magnetic fields

Under various amplitude of AC magnetic fields domain wall motion is the main mechanism in the magnetization process. This includes domain wall bulging and domain wall displacing. In this paper complex permeability-frequency spectra of (Fe_1−xCo_x)_73.5Cu₁Nb₃Si_13.5B₉ (x=0,0.5$x=0,0.5$) nanocrystalline alloys were measured as a function of the AC magnetic field, ranging from 0.001 to 0.04 Oe. Obvious changes have been found in complex permeability spectra for alloy x=0$x=0$ with the change of the amplitude of AC magnetic field, but variation of AC magnetic field has little effect on complex permeability spectra for alloy x=0.5$x=0.5$. This is attributed to the increased pinning field after substitution of Fe with Co in Fe_73.5Cu₁Nb₃Si_13.5B₉ nanaocrystalline alloy.     

High concentration of hematite nanoparticles in a silica matrix: Structural and magnetic properties

The α-Fe₂O₃/SiO₂ nanocomposite containing 45 wt% of hematite was prepared by the sol-gel method followed by heating in air at 200 °C. The so-obtained composite of iron(III) nanoparticles dissolved in glassy silica matrix was investigated by X-ray powder diffraction (XRPD), transmission electron microscopy (TEM), and superconducting quantum interference device (SQUID) magnetometry. XRPD confirms the formation of a single-phase hematite sample, whereas TEM reveals spherical particles in a silica matrix with an average diameter of 10 nm. DC magnetization shows bifurcation of the zero-field-cooled (ZFC) and field-cooled (FC) branches up to the room temperature with a blocking temperature T_B=65 K. Isothermal M(H) dependence displays significant hysteretic behaviour below T_B, whereas the room temperature data were successfully fitted to a weighted Langevin function. The average particle size obtained from this fit is in agreement with the TEM findings. The small shift of the T_B value with the magnetic field strength, narrowing of the hysteresis loop at low applied field, and the frequency dependence of the AC susceptibility data point to the presence of inter-particle interactions. The analysis of the results suggests that the system consists of single-domain nanoparticles with intermediate strength interactions.     

Effect of γ-ray irradiation on the magnetic properties of NdFeB and Fe–Cr–Co permanent magnets

The effect of γ-ray irradiation on the magnetic properties of NdFeB and Fe–Cr–Co permanent magnets has been investigated. The magnetic flux loss of two kinds of magnets before and after irradiation was measured. Results show that the effect of γ-ray irradiation on the magnetic properties of sintered NdFeB is not so obvious as that on Fe–Cr–Co magnet. Irradiation-induced damage from γ-ray for the Fe–Cr–Co magnets was characterized for the first time. The decline of permanent magnetic properties of Fe–Cr–Co magnet induced by γ-ray irradiation is reversible except for the maximum energy product (BH)_max. The difference of coercivity mechanism between these two kinds of permanent magnets is responsible for the different dependence of magnetic properties loss induced by γ-ray irradiation.     

The role of dipolar interaction in nanocomposite permanent magnets

The effects of dipolar interactions on the magnetization behaviors and magnetic properties of the nanocomposite magnets have been studied by micromagnetic simulations. Numerical results show that the dipolar interaction plays an important role during the demagnetization process, especially in the magnets with large soft-phase content _vs$v_{\mathrm{s}}$. For the isotropic nanocomposites, the remanence enhancement can be controlled through adjustments of the grain size D   and _vs$v_{\mathrm{s}}$. However, the appearance of magnetic vortex state leads to a very low remanence in the magnets with large D   and _vs$v_{\mathrm{s}}$. The dependence of coercivity on D   and _vs$v_{\mathrm{s}}$ can be attributed to the exchange-induced magnetization reversal near the grain boundaries and the low nucleation field of soft phase, respectively. For the anisotropic nanocomposites, the reduced remanence _mr$m_{\mathrm{r}}$ is equal to 1.0$1.0$ for the magnets with small D   or with low _vs$v_{\mathrm{s}}$. However, _mr$m_{\mathrm{r}}$ decreases with increasing _vs$v_{\mathrm{s}}$ for the magnet with large D   due to the influence of dipolar interactions. The difference between the calculated coercivity _Hc$H_{\mathrm{c}}$ with and without considering dipolar interaction shows that the dipolar interaction plays a more important role during the magnetization reversal in the soft phase than that in the hard phase. The maximum calculated energy product of the isotropic nanocomposites is only about 40 MGOe due to the conflicting relation between remanence and coercivity, while that of the anisotropic nanocomposites is 112 MGOe. This reminds us that the alignment of hard grain is important to obtain high performance.     

THz Generation by Optical Rectification and Competition with Other Nonlinear Processes

We present a study of the competition between tera-hertz （THz） generation by optical rectification in （110） ZnTe crystals, two-photon absorption, second harmonic generation and free-carrier absorption. The two-photon nonlinear absorption coefficient, second harmonic generation efficiency and free-carrier absorption coefficient in the THz range are measured independently. The incident pump field is shown to be depleted by two-photon absorption and the THz radiation is shown to be reduced, upon focusing, by free-carrier absorption. The reduction of the generated THz radiation upon tight focusing is explained, provided that one also takes into account diffraction effects from the sub-wavelength THz source.     

Synthesis and magnetic properties of antiferromagnetic Co3O4 nanoparticles

Antiferromagnetic Co₃O₄ nanoparticles with diameter around 30 nm have been synthesized by a solution-based method. The phase identification by the wide-angle X-ray powder diffraction indicates that the Co₃O₄ nanoparticle has a cubic spinel structure with a lattice constant of 0.80843(2) nm. The image of field emission scanning electron microscope shows that the nanoparticles are assembled together to form nanorods. The magnetic properties of Co₃O₄ fine particles have been measured by a superconducting quantum interference device magnetometer. A deviation of the Néel temperature from the bulk is observed, which can be well described by the theory of finite-size scaling. An enhanced coercivity as well as a loop shift are observed in the field-cooled hysteresis loop. The exchange bias field decreases with increasing temperature and diminishes at the Néel temperature. The training effect and the opening of the loop reveal the existence of the spin-glass-like surface spins.     

Effects of precursor types of Fe and Ni components on the properties of NiFe2O4 powders prepared by spray pyrolysis

The effects of the precursor types of Ni and Fe components on the morphology, mean size, and magnetic property of NiFe₂O₄ powders prepared by spray pyrolysis from the spray solution, with citric acid were studied. The precursor powders with hollow and thin wall structure turned to the nano-sized NiFe₂O₄ powders after post-treatment at a temperature of 800 °C. The nickel ferrite powders obtained from the spray solution with ferric chloride had nanometer sizes and narrow size distributions irrespective of the types of nickel precursor. The nickel ferrite powders obtained from the spray solution with ferric nitrate and nickel chloride also had nanometer size and narrow size distribution. The saturation magnetizations of the NiFe₂O₄ powders changed from 37 to 42 emu/g according to the types of the Fe and Ni precursors. The saturation magnetizations of the NiFe₂O₄ powders increased with increasing the Brunauer-Emmett-Teller (BET) surface areas of the powders.     

Mössbauer studies on the superparamagnetic behavior of CoFe2O4 with a few nanometers

CoFe₂O₄ nanoparticles with a cubic spinel structure are prepared by a high-temperature thermal decomposition method. The average particle sizes are 4.6  and 5.7 nm for CoFe₂O₄ made with two kinds of solvents by TEM. Mössbauer spectra of 4.6 nm particles displayed a superparamagnetic behavior as demonstrated by a single line with zero hyperfine fields, but that of 5.7 nm particles did not at room temperature. It is considered that anisotropy energy was still more superior to thermal energy because of particle size of 5.7 nm CoFe₂O₄. Furthermore, Mössbauer spectra exhibited the typical spectrum shapes of the CoFe₂O₄ at 4.2 K. The spectrum at 4.2 K was fitted using two magnetic components of hyperfine fields _Hhf=540.4,512.6$H_{\mathrm{hf}}=540.4,512.6$ kOe and isomer shifts δ=0.40,0.30$\delta =0.40,0.30$ mm/s for 4.6 nm and _Hhf=542.7,512.8$H_{\mathrm{hf}}=542.7,512.8$ kOe and δ=0.41,0.29$\delta =0.41,0.29$ mm/s for 5.7 nm corresponding to Fe³⁺ ions at site A and site B, respectively.