Evolution of magnetic and microstructural properties of thick sputtered NdFeB films with processing temperature

Ta (100 nm)/NdFeB (5 μm)/Ta (100 nm) films have been deposited onto Si substrates using triode sputtering (deposition rate ∼18 μm/h). A 2-step procedure was used: deposition at temperatures up to 400 °C followed by ex-situ annealing at higher temperatures. Post-deposition annealing temperatures above 650 °C are needed to develop high values of coercivity. The duration of the annealing time is more critical in anisotropic samples deposited onto heated substrates than in isotropic samples deposited at lower temperatures. For a given set of annealing conditions (750 °C/10′), high heating rates (?2000 °C/h) favour high coercivity in both isotropic and anisotropic films. The shape and size of Nd₂Fe₁₄B grains depend strongly on the heating rate.     

Improving magnetic properties of barium hexaferrites by La or Pr substitution

La or Pr substituted barium hexaferrites, Ba_1−x(La or Pr)_xFe₁₂O₁₉, x=0.00-0.20, were successfully prepared by a citrate combustion process. The sintered bodies were structurally and magnetically studied by powder X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). All XRD patterns show the single phase of the magnetoplumbite barium ferrite without other intermediate phases. Magnetization (M_S) and coercive field (H_C) could be improved by substitutions of La or Pr ions on Ba ion basis sites. The M_S reveal magnetic behavior with respect to La or Pr ions content, showing an increase at first and then a decrease. The H_C increases remarkably with increasing La or Pr ions content.     

Studies on the magnetic properties for single-phase nanocrystalline FePt magnets with different orientation degrees

The single-phase nanocrystalline FePt magnets composed of 343 irregular-shaped grains are built. The demagnetization curves are simulated by micromagnetic finite element method. The remanence, coercivity and maximum energy product of the magnets decrease with deteriorating grain alignment. The characteristics of variation of magnetic properties with the degree of orientation are closely related to the average grain size of nanocrystalline magnets. The contribution of intergrain exchange coupling (IGEC) to remanence enhancement is associated to the degree of orientation, and decreases with improved grain alignment. With decreasing grain size, coercivity increases for anisotropic nanocrystalline magnets, which is completely different from that of isotropic nanocrystalline magnets.     

Effect of γ-ray irradiation on the magnetic properties of NdFeB and Fe–Cr–Co permanent magnets

The effect of γ-ray irradiation on the magnetic properties of NdFeB and Fe–Cr–Co permanent magnets has been investigated. The magnetic flux loss of two kinds of magnets before and after irradiation was measured. Results show that the effect of γ-ray irradiation on the magnetic properties of sintered NdFeB is not so obvious as that on Fe–Cr–Co magnet. Irradiation-induced damage from γ-ray for the Fe–Cr–Co magnets was characterized for the first time. The decline of permanent magnetic properties of Fe–Cr–Co magnet induced by γ-ray irradiation is reversible except for the maximum energy product (BH)_max. The difference of coercivity mechanism between these two kinds of permanent magnets is responsible for the different dependence of magnetic properties loss induced by γ-ray irradiation.     

Effect of SiO2 nanopowders on magnetic properties and corrosion resistance of sintered Nd-Fe-B magnets

To improve the magnetic properties and corrosion resistance of magnet, SiO₂ nanopowders were added into Nd_28.25Dy_2.75Fe_balAl_0.15Ga_0.1Nb_0.1B_0.98-sintered magnets as grain boundary modifiers. It was found that the intrinsic coercivity (H_cj), remanence (B_r) and corrosion resistance were all improved with addition of certain amount of SiO₂ nanopowders. The optimum addition amount of SiO₂ nanopowders was found to be 0.01 wt%. Thermodynamic calculation in combination of energy dispersive X-ray spectroscopy (EDX) analyses indicated that SiO₂ nanopowders reacted with Nd of Nd-rich phase. As a result, the intergranular phase was modified, and the grain growth of main phase was restrained. It led to the optimization of microstructure.     

Study of the magnetic properties of the permanent magnets by Mössbauer spectroscopy

This paper presents methods that can be used in order to determine the relative remanent magnetization and uniaxial magnetic anisotropy constant of particles in powder-based permanent magnets using Mössbauer spectroscopy. The methods were verified on the permanent magnet barium ferrite.     

Structural and magnetic properties of SmCo5.6Ti0.4 alloy

Three series of SmCo_5.6Ti_0.4 samples were prepared by quenching, melt spinning, and ball milling, respectively. Annealing at different temperatures was carried out for the three series. The influence of the processing routes on the structural and magnetic properties was systematically investigated for this alloy. The as-quenched bulk sample consisted of three phases with a rather coarse grain microstructure. Low intrinsic coercivity (_iH_c) of 0.12 T was obtained in this sample. While the as-spun ribbons and as-milled/annealed powders showed the CaCu₅-type phase (1:5) plus Th₂Zn₁₇-type phase (2:17), and the 1:5 phase plus TbCu₇-type phase (1:7), respectively, with nanograin microstructure. The _iH_c of as-spun ribbons and as-milled/annealed (700 °C for 2 h) powders was found to be 0.59 and 2.23 T, respectively. Coercivity mechanism of these as-spun ribbons is mainly of nucleation type. In the as-milled/annealed powders, the network of the nanograin boundaries is believed to provide strong pinning sites for the domain wall movement.     

Structure and magnetic properties of SmCoxTi0.4-1:7 ribbons

SmCo_xTi_0.4 (x=6.6, 7.1, 7.6, 8.1) ribbons have been prepared by melt spinning at a wheel speed of 42 m/s, followed by annealing at 750 °C for 2 h. Both as-spun and as-annealed ribbons possess the disordered TbCu7-type (1:7) phase even when the Sm/(Co,Ti) atomic ratio deviates from 1/7. The c/a ratio increases with increasing Co concentration x, but the unit cell volume decreases. The Curie temperatures show above 700 °C, increasing from 707 °C for x=6.6 to 782 °C for x=8.1. The saturation magnetizations increase almost linearly with increasing Co content. The observed magnetic hardening is believed to arise from the high magnetocrystalline anisotropy of the 1:7 phase and the fine nanograin structure. The intrinsic coercivity of 9797 Oe has been obtained in the melt-spun SmCo_7.1Ti_0.4 ribbons.     

The influence of thermal annealing on the structural and magnetic properties of gold nanoparticles

In the past few years ferromagnetic-like behavior has been reported in metal gold nanoparticles coated with diverse organic surfactants. In this work we report on the effect of thermal annealing on the ferromagnetic-like behavior of oleic acid and oleylamine coated gold nanoparticles of about 7 nm size. The magnetic moment of the “as prepared” sample is about 3×10⁻² emu/g and the coercive field is 200 Oe at 10 kOe and 5 K, after the annealing the behavior changes from ferromagnetic-like to paramagnetic and the magnetization at 10 kOe decreases at a factor of 10. These results are compared with those obtained for oleylamine coated gold nanoparticles, which are diamagnetic at room temperature.     

Research on La–Co-substituted strontium ferrite magnets for high intrinsic coercive force

M-type strontium ferrites with substitution of Sr²⁺ by rare-earth La³⁺, and a little amount of Fe³⁺ by Co²⁺ according to the formula Sr_1−xLa_xFe_12−xCo_xO₁₉, are prepared by the ceramic process. Effects of the substituted amount of La³⁺ and Co²⁺ on structure and magnetic properties of Sr_1−xLa_xFe_12−xCo_xO₁₉ compounds have systematically been investigated by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and B–H hysteresis curve measurements. In our results, the suitable amount of La³⁺–Co²⁺ substitution may remarkably increase saturation magnetization. Intrinsic coercive force (H_cj) of Sr ferrite magnets is evidently increased without significant decrease in residual flux density (B_r) by La³⁺–Co²⁺ substitution.     

Effect of Fe substitution on the magnetic properties of half-Heusler alloy CoCrAl

The effect of Fe substitution for the vacant site in half-Heusler alloy CoCrAl is studied. A series of single phase CoFe_xCrAl (x=0.0, 0.25, 0.5, 0.75 and 1.0) alloys has been successfully synthesized. The lattice constant is found to increase almost linearly with increasing Fe content, indicating Fe atoms enter the lattice of CoCrAl instead of existing as a secondary phase. When Fe entering the vacant site, spin polarization occurs and the alloy turns from a semimetal in CoCrAl to a half-metallic ferromagnet (HMF) in CoFeCrAl. This is due to the reconstruction of the energy band with Fe substitution. The Curie temperature and saturation magnetic moments are enhanced and increase monotonically with increasing Fe content. The variation of the spin moment follows the Slater-Pauling curve and agrees with the theoretical calculation as well.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Influence of Ge on magnetic and structural properties of Joule-heated Co-based ribbons: Giant magnetoimpedance response

Studies of magnetic and structural properties of Fe_3.5Co_66.5Si_12−xGe_xB₁₈ (x=0, 3, and 6) soft magnetic ribbons obtained by melt-spinning were performed. The samples were submitted to Joule-heating treatments with different maximum current values (0.01, 0.05, 0.1, 0.2, and 0.8 A, respectively) with steps of 0.01 A and times by step of 1, 2, and 10 s). X-ray diffraction, temperature dependence of magnetization (for the as-quenched samples), coercivity and giant magnetoimpedance (GMI), measured at different frequencies (100, 500, and 900 kHz, respectively) were performed. All the samples crystallized at annealing currents higher than 0.4 A, which was consistent with the magnetic hardening of the material. Coercivities less than 1 A/m were obtained for the three samples between 0.1 and 0.2 A. Maximum value of GMI response was observed for the sample without Ge in the as-quenched state.     

Mössbauer effect studies of RFe11Ti and RFe11TiH (R=Y,Gd, Er)

The Mössbauer spectra of ferromagnetic RFe₁₁Ti and RFe₁₁TiH_x   (R=Y$R=\mathrm{Y}$, Gd, Er, x=0$x=0$, 1) have been investigated in the temperature range 20–300 K and analysed in terms of a new model which allows a better fit of the spectra using less constraints than previously reported analyses. In addition to the dependence of magnetic hyperfine field and isomer shift on the number of Ti nearest-neighbours (NN) of the Fe atoms, this new model also considers the effect of the average interatomic distances between Fe atoms on the 8i, 8f and 8j crystallographic sites. Magnetic hyperfine fields were found to decrease with the average interatomic distances for Fe atoms on the same sites and with the same number of iron NN. This decrease was however lower than that due to the presence of one additional titanium NN. Furthermore the present model distinguishes the 8f from the 8j sites on the basis of the relative areas of the corresponding sextets. It leads to higher average magnetic hyperfine fields and isomer shifts for the 8f site as compared to the 8j sites which may be understood on the basis of electronic charge transfer between the rare-earth and Fe atoms. The dependence of hyperfine parameters on the number of titanium NN and on hydrogenation is similar to those previously reported.     

Structural,microstructural and magnetic properties of nanocomposite isotropic Sm(CobalFe0.1MyZr0.04B0.04)7.5 ribbons with M=Ni,Cu and y=0.09 and 0.12

In boron-substituted melt-spun Sm(Co,Fe,Cu,Zr)_7.5-type alloys a nanocomposite microstructure and high coercivities in both as-spun and short-time annealed ribbons can be obtained. In the present study three different compositions, namely Sm(Co_0.73Fe_0.1Cu_0.09Zr_0.04B_0.04)_7.5, Sm(Co_0.70Fe_0.1Cu_0.12Zr_0.04B_0.04)_7.5 and Sm(Co_0.70Fe_0.1Ni_0.12Zr_0.04B_0.04)_7.5 have been examined in order to investigate the influence of composition on the magnetic properties and the microstructure. Melt-spun ribbons have been obtained and annealing has been followed under argon atmosphere for 30–75 min at 600–870 °C. For the as-spun ribbons the TbCu₇-type of structure and fcc-Co as a secondary phase have been identified in the X-ray diffraction patterns. For the annealed ribbons above 700 °C the 1:7 phase transforms into 2:17 and 1:5 phases. The TEM studies have shown a homogeneous nanocrystalline microstructure with average grain size of 30–80 nm. Coercivity values of 15–27 kOe have been obtained from hysteresis loops traced in non-saturating fields. The coercivity decreases with temperature, but it is sufficiently large to maintain values higher than 5 kOe at 380 °C.     

Effect of hydrogen doping on the magnetic properties of Gd2CuO4

We report the results of ac-susceptibility and dc-magnetization measurements for H_yGd₂CuO₄ (0y0.54). It is shown thatH doping lowers the weak ferromagnetic component in the material. The distinct hysteresis loops observed atT=77 K for both non- and hydrogenated samples change its shape withy. The magnetic ordering temperatures T _N ^Cu and T _N ^Gd , as determined from the temperature dependencies of ac-susceptibility, remain unchanged with sample's hydrogenation. This result seems to indicate that extra electrons are not doped onto the Cu-O planes of Gd₂CuO₄. The frequency dependencies ofx(, T) andx(, T) for bothy=0 andy=0.15 samples are analysed., The maximums ofx andx found at about 200K are considered in terms of susceptibility dependence on the spin-lattice relaxation time (). The anomalies in ac-susceptibility found recently in Gd₂CuO₄ atT _a=8 K andT _b=9.5 K decrease significantly withy. Results are discussed in the context of available data on 214T-type compounds.     

Barium ferrite powders prepared by microwave-induced hydrothermal reaction and magnetic property

We have prepared barium ferrite particles by the microwave-induced hydrothermal method. The crystallization of the barium ferrite particles is promoted within a short time by microwave irradiation because the seeds of barium ferrite having large permeability are rapidly heated through the interaction of barium ferrite with the magnetic component of the microwaves. Crystals having unusually low thickness were obtained compared with the conventional hydrothermal method. The magnetic properties of barium ferrite particles are discussed.     

Critical bond lengths and their role in spontaneous magnetostriction of R2Fe17CX (R=Y,Nd, Gd,Tb, Er)

High-energy high-flux synchrotron X-rays have been used to study the spontaneous magnetostriction of R₂Fe₁₇ (R=Y, Nd, Gd, Tb, Er) and their carbides in the temperature range 10–1100 K. Addition of interstitial carbon greatly increases both the Curie temperatures (T_C) and the spontaneous magnetostrain of the compounds, while reduces the anisotropy of the magnetostrain by expanding the distances between rare-earth and neighboring Fe sites. The increase of T_C with carbon is due to the increased spatial separation of the Fe hexagon layers. On the basal plane, the Fe hexagons are squeezed and the contribution of Fe sublattice to spontaneous magnetostriction is attenuated, while that of rare-earth sublattice is enhanced. The average bond magnetostrain around Fe sites are in linear relation with their hyperfine field intensities.     

Effect of Cu and Ga additions on the anisotropy of R2Fe14B/α-Fe nanocomposite die-upset magnets (R=Pr,Nd)

Fully dense nanocomposite magnets containing hard R₂Fe₁₄B and soft α-Fe phases were produced from both melt-spun and mechanically milled alloys by hot pressing and subsequent die upsetting. Although R-lean R–Fe–B alloys that do not contain the grain-boundary R-rich phase are known not to be susceptible to texture development by means of die upsetting, we found that small additions of Cu make the texturing possible. The resulting microstructure of oriented platelet grains is similar to that of the R-rich die-upset magnets. Properties of the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets can be further improved by adding Ga. The anisotropic Pr₁₂Fe₈₀Cu₁Ga₁B₆ magnet made from mechanically milled alloy and containing 17.2 wt% α-Fe had a remanence of 13 kG and a maximum energy product of 23.4 MG Oe. The Pr_11.25Fe_80.75Cu₁Ga₁B₆ magnet made from melt-spun alloy and containing 16.2 wt% α-Fe had a maximum energy product of 19.9 MG Oe. The low coercivity of 3–4 kOe typical for the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets is due to the relatively coarse α-Fe grains. The latter grains are too large for intergranular exchange interaction, but, nevertheless, they are well coupled with the R₂Fe₁₄B grains by a long-range magnetostatic interaction.