Thickness dependence on thermal stability of sputtered Ag nanolayer on Ti/Si(1 0 0)

Thermal stability of Ag layer on Ti coated Si substrate for different thicknesses of the Ag layer have been studied. To do this, after sputter-deposition of a 10 nm Ti buffer layer on the Si(1 0 0) substrate, an Ag layer with different thicknesses (150-5 nm) was sputtered on the buffer layer. Post annealing process of the samples was performed in an N₂ ambient at a flow rate of 200 ml/min in a temperature range from 500 to 700 °C for 30 min. The electrical property of the heat-treated multilayer with the different thicknesses of Ag layer was examined by four-point-probe sheet resistance measurement at the room temperature. Phase formation and crystallographic orientation of the silver layers were studied by θ-2θ X-ray diffraction analysis. The surface topography and morphology of the heat-treated films were determined by atomic force microscopy, and also, scanning electron microscopy. Four-point- probe electrical measurement showed no considerable variation of sheet resistance by reducing the thickness of the annealed Ag films down to 25 nm. Surface roughness of the Ag films with (1 1 1) preferred crystallographic orientation was much smaller than the film thickness, which is a necessary condition for nanometric contact layers. Therefore, we have shown that the Ag layers with suitable nano-thicknesses sputtered on 10 nm Ti buffer layer were thermally stable up to 700 °C.     

Preparation and characterization of C54 TiSi2 nanoislands on Si (1 1 1) by laser deposition of TiO2

We present the preparation of C54 TiSi₂ nanoislands on Si (1 1 1) with a method of the pulsed laser deposition of titanium oxide thin films. The TiO₂ thin films with nominal thicknesses of 1 nm on Si (1 1 1) were annealed at 850 °C for about 4 h in situ. The X-ray diffraction patterns and the X-ray photoelectron spectra indicate that the nanoislands are in C54 TiSi₂ phase. The characterization using a scanning tunneling microscope shows that the nanoislands with triangular, polygonal and rod-like shapes on Si (1 1 1) exhibit the Volmer-Weber growth mode. The sizes of the polygonal islands distribute in two separated ranges. For the small islands, they have a narrow lateral size distribution centered at 4 nm and a height range in 0.6-3.6 nm, while for the large islands, their lateral sizes are in the range of 12-40 nm and the heights in the range of 4-9 nm. The sizes of the well-shaped triangular islands are intermediate with the lateral sizes in range of 5-20 nm and the heights of 2-3.5 nm. The rod-like islands are about 50-200 nm in length, 5 nm in height and about 15-20 nm in width. The origination of the various shapes of the nanoislands is attributed to the symmetry of Si (1 1 1) substrate and the lattice mismatch between the C54 TiSi₂ and the Si (1 1 1) surface.     

Fourfold in-plane magnetic anisotropy in epitaxial Fe(1 1 0)/Cu(0 0 1) and Fe(1 1 0)/Ni(0 0 1) bilayers

Epitaxial Fe(1 1 0) films with thicknesses of 100-800 nm on Cu(0 0 1) and Ni(0 0 1) buffer layers grown on MgO(0 0 1) substrates have been fabricated. These films contain Fe(1 1 0) crystallites which are in the Pitsch orientation relationship. Magnetization and the fourfold in-plane magnetic anisotropy constants of these films have been determined by torque measurements. All the samples under study are characterized by a fourfold magnetic anisotropy with easy axes parallel to the [1 0 0] and [0 1 0] directions of Cu(0 0 1) and Ni(0 0 1) layers. The measured values of the constant for Fe(1 1 0)/Cu(0 0 1) are found to depend on deposition temperature; a maximum value of (2.5±0.1)×10⁵ erg/cm³ is reached after annealing at 600 °С. The in-plane torque measurements on Fe(1 1 0)/Ni(0 0 1) bilayers obtained at 300 °С, on the other hand, exhibit a constant value of (2.7±0.1)×10⁵ erg/cm³. Assuming an exchange interaction between the Fe(1 1 0) crystallites, which are in the Pitsch orientation relationship, the fourfold in-plane magnetic anisotropy has been calculated as 2.8×10⁵ erg/cm³. The deviations of the experimental values from the predicted one may be explained by the formation of a polycrystalline phase within the Fe(1 1 0) layer and a partial disorientation of the epitaxial crystallites.     

Seedlayer interface enhanced magnetic anisotropy in CoPt (0 0 0 2)-textured films

The effects of interface roughness of Ta seedlayer on the structural and magnetic properties of Co₇₂Pt₂₈(20 nm)/Ru(30 nm)/Pt(2 nm)/Ta(5 nm)/glass were investigated. Uniaxial perpendicular magnetic anisotropy (8.6×10⁶ ergs/cc), coercivity (5.5 kOe) and nucleation field (−2.8 kOe) in the Co₇₂Pt₂₈ thin film sputter-deposited on relatively smooth surface of Ta seedlayer were achieved. The results showed that relatively smoother interface roughness of Ta seedlayer improved the CoPt/Ru (0 0 0 2) texture and magnetic properties.     

Structural and morphological characterisation of hybrid Cu/Si(0 0 1) structures

The structural and morphological properties of epitaxial Cu/Si(0 0 1) type of structures have been investigated by a combination of electron, X-ray and scanning probe imaging techniques. Auger electron spectroscopy measurements indicate the presence of Si in the Cu layer for Cu thicknesses up to 10 nm. In addition, X-ray scattering results show that there is a mosaic spread in the Cu(0 0 1) crystal which decreases as the Cu thickness increases, from 8° at 15 nm to 4.5° at 100 nm. This behaviour is corroborated by reflection high energy electron diffraction patterns of the Cu surface measured during growth, which exhibit a twinning in the diffraction spots for the 15 and 30 nm Cu films. Atomic force and scanning electron microscopy imaging of Cu(4 nm)/Co(7,17 nm)/Cu(100 nm)/Si(0 0 1) structures allow one to visualise and characterise the sample surface in real space; from these measurements, an average roughness amplitude of ∼0.5 nm and a correlation length of ∼50 nm are obtained. Our results provide a better understanding of an important system which has been widely used as a template for the growth of epitaxial ultrathin magnetic films.     

Determination of a (4 × 4) structure formed on a Cu(0 0 1) surface by adsorption of calcium

The adsorption of calcium (Ca) atoms on a Cu(0 0 1) surface has been studied by low-energy electron diffraction (LEED) at 130, 300 and 400 K. It is found that a (4 × 4) was the only LEED pattern appeared at 400 K while a quasi-hexagonal structure was formed in a wide range of submonolayer coverage at 130 K. At 300 K, the (4 × 4) LEED spots were broad and weak. The (4 × 4) structure formed at 400 K was determined by a tensor LEED I-V analysis. It is a new-type of surface alloys consisting of five substitutional Ca atoms, nine surface Cu atoms, and two atomic vacancies in the unit cell. In spite of a quite large size-difference between Ca (3.94 Å) and Cu (2.55 Å) atoms, all Ca atoms are located at the substitutional sites. Among surface alloys so far reported, the atomic size ratio between Cu and Ca in the (4 × 4), 1.54, is the largest. Optimized structural parameters reveal that large lateral displacements of surface Cu atoms, being enabled by the appearance of the vacancies, allow the formation of the (4 × 4) structure.     

Low-frequency noise and inelastic tunneling spectroscopy in Fe(1 1 0)/MgO(1 1 1)/Fe(1 1 0) epitaxial magnetic tunnel junctions

We report on tunnelling magnetoresistance (TMR), current–voltage (IV) characteristics and low-frequency noise in epitaxially grown Fe(1 1 0)/MgO(1 1 1)/Fe(1 1 0) magnetic tunnel junctions (MTJs) with dimensions from 2×2 to 20×20 μm². The evaluated MgO energy barrier (0.50±0.08 eV), the barrier width (13.1±0.5 Å) as well as the resistance times area product (7±1 MΩ μm²) show relatively small variation, confirming a high quality epitaxy and uniformity of all MTJs studied. At low temperatures (T<10 K) inelastic electron tunneling spectroscopy (IETS) shows anomalies related to phonons (symmetric structures below 100 meV) and asymmetric features above 200 meV. We explain the asymmetric features in IETS as due to generation of electron standing waves in one of the Fe electrodes. The noise power, though exhibiting a large variation, was observed to be roughly anti-correlated with the TMR. Surprisingly, for the largest junctions we observed a strong enhancement of the normalized low-frequency noise in the antiparallel magnetic configuration. This behavior could be related to the influence of magnetostriction on the characteristics of the insulating barrier through changes in local barrier defects structure.     

Study of S ion-assisted sulfurization of n-GaAs (1 0 0) surface

The chemical structure and site location of sulfur atoms on n-GaAs (1 0 0) surface treated by bombardment of S⁺ ions over their energy range from 10 to 100 eV have been studied by X-ray photoelectron spectroscopy and low energy electron diffraction. The formation of Ga-S and As-S species on the S⁺ ion bombarded n-GaAs surface is observed. An apparent donor doping effect is observed for the n-GaAs by the 100 eV S⁺ ion bombardment. It is found that the S⁺ ions with higher energy are more effective in the formation of Ga-S species, which assists the n-GaAs (1 0 0) surface in reconstruction into an ordered (1 × 1) structure upon subsequent annealing. The treatment is further extended to repair Ar⁺ ion damaged n-GaAs (1 0 0) surface. It is found that after a n-GaAs (1 0 0) sample is damaged by 150 eV Ar⁺ ion bombardment, and followed by 50 eV S⁺ ion treatment and subsequent annealing process, finally an (1 × 1) ordering GaAs (1 0 0) surface with low surface states is obtained.     

Structure and electronic properties of gold adsorbed on Ti(0 0 0 1)

The Au/Ti(0 0 0 1) adsorption system was studied by low energy electron diffraction (LEED) and photoemission spectroscopy with synchrotron radiation after step-wise Au evaporation onto the Ti(0 0 0 1) surface. For adsorption of Au at 300 K, no additional superstructures were observed and the (1 × 1) pattern of the clean surface simply became diffuse. Annealing of gold layers more than 1 ML thick resulted in the formation of an ordered Au-Ti surface alloy. Depending on the temperature and annealing time, three surface reconstructions were observed by LEED: (√3 × √3) R30°, (2 × 2) and a one-dimensional incommensurate (√3 × √3) rectangular pattern. The Au 4f core level and valence band photoemission spectra provided evidence of a strong chemical interaction between gold and titanium. The data indicated formation of an intermetallic interface and associated valence orbital hybridization, together with diffusion of gold into the bulk. Au core-level shifts were found to be dependent on the surface alloy stoichiometry.     

A low temperature surface preparation method for STM nano-lithography on Si(1 0 0)

Registration markers are crucial in connecting scanning tunneling microscope (STM) lithographed nano- and atomic-scale devices to the outside world. In this paper we revisit an ultra high vacuum annealing method with a low thermal budget that is fully compatible with etched registration markers and results in clean 2 × 1 reconstructed Si(1 0 0) surfaces required for STM lithography. Surface contamination is prevented by chemically stripping and reforming a protective silicon oxide layer before transferring the sample to the vacuum system. This allows for annealing temperatures of only 900 °C, where normally carbon contaminants result in the formation of SiC clusters on the surface at annealing temperatures below 950 °C. Reactive ion etched marker structures with an etch depth of 60 nm and a typical lateral dimension of only 150 nm survive a 900 °C flash anneal.     

Rate coefficients measurement for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F)

We report experimental rate coefficients for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F). In the experiment the Cs(5D) state was populated via photodissociation of Cs₂ molecules using an argon-ion laser at wavelength 488.0 nm. We also consider the competing process 6P_1/2 + 7S → 6S + (nl = 9D, 11S, 7F) that might also populate 9D, 11S and 7F. An intermodulation technique was used to select the fluorescence contributions due only to the process 6P_1/2 + 7S → 6S + (nl = 9D, 11S, 7F). The excited atom (nl_J) density and spatial distribution were mapped by monitoring the absorption of a counterpropagating probe laser beam tuned to various transitions. The measured excited atom densities are combined with measured fluorescence ratios to yield rate coefficients for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F). The rate coefficients for nl = 9D, 11S, 7F are (4.1 ± 2.0) × 10⁻¹⁰ cm³ s⁻¹, (1.6 ± 0.8) × 10⁻¹⁰ cm³ s⁻¹ and (3.6 ± 1.8) × 10⁻¹⁰ cm³ s⁻¹, respectively. The contributions to the rate coefficients from other energy transfer processes are also discussed.     

An ab initio-based approach to phase diagram calculations for GaN(0 0 0 1) surfaces

Surface phase diagrams of GaN(0 0 0 1)-(2 × 2) and pseudo-(1 × 1) surfaces are systematically investigated by using our ab initio-based approach. The phase diagrams are obtained as functions of temperature T and Ga beam equivalent pressure p_Ga by comparing chemical potentials of Ga atom in the vapor phase with that on the surface. The calculated results imply that the (2 × 2) surface is stable in the temperature range of 700-1000 K at 10⁻⁸ Torr and 900-1400 K at 10⁻² Torr. This is consistent with experimental stable temperature range for the (2 × 2). On the other hand, the pseudo-(1 × 1) phase is stable in the temperature range less than 700 K at 10⁻⁸ Torr and less than 1000 K at 10⁻² Torr. Furthermore, the stable region of the pseudo-(1 × 1) phase almost coincides with that of the (2 × 2) with excess Ga adatom. This suggests that Ga adsorption or desorption during GaN MBE growth can easily change the pseudo-(1 × 1) to the (2 × 2) with Ga adatom and vice versa.     

SR-PES and STM observation of metastable chemisorption state of oxygen on Si(1 1 0)-16 × 2 surface

Initial adsorption of oxygen molecules on the Si(1 1 0)-16 × 2 surface and subsequent modification of the bonding states induced by mild (300 °C) annealing have been studied by synchrotron-radiation photoemission spectroscopy and scanning-tunneling microscopy. It has been shown that upon annealing, the intensity and the energy positions of the Si 2p suboxide components shift towards the values characteristic for the thermal oxide. This indicates the presence of a metastable chemisorption state of oxygen on the Si(1 1 0)-16 × 2 surface.     

Needle-like domain structure in Co films deposited on Mo (1 1 0)

Magnetization reversal processes and domain structures have been studied in Mo(1 1 0)/Co(0 0 0 1)/Au(1 1 1) structures grown by molecular beam epitaxy on monocrystalline (11–20) sapphire substrates. Wedge-shaped samples with different Co thickness gradients relative to the Mo [0 0 1] direction were fabricated. Observation of the domain structure was performed at room temperature using Kerr microscopy in a Co thickness range varying from 5 to 50 nm, where the magnetization is oriented in the plane of the sample. A Co thickness-dependent coercivity field was determined through analysis of the domain wall position during the reversal process. A preferential orientation of magnetic domain walls was found, with the domains being needle-like. The orientation, as well as the size of the needles, depends on the Co thickness and the orientation of the magnetic field applied in the sample plane.     

Surface treatments toward obtaining clean GaN(0 0 0 1) from commercial hydride vapor phase epitaxy and metal-organic chemical vapor deposition substrates in ultrahigh vacuum

We studied processes of cleaning GaN(0 0 0 1) surfaces on four different types of wafers: two types were hydride vapor phase epitaxy (HVPE) free-standing substrates and two types were metal-organic chemical vapor deposition (MOCVD) films grown on these HVPE substrates and prepared by annealing and/or Ar ion sputtering in ultra high vacuum. We observed the surfaces through treatments using in situ low-energy electron diffraction (LEED), reflection high-energy electron diffraction (RHEED), scanning tunneling microscopy (STM), and Auger electron spectroscopy, and also using ex situ temperature programmed desorption, X-ray photoelectron spectroscopy, X-ray diffraction, and secondary ion mass spectrometry. For HVPE samples, we obtained relatively clean surfaces under optimized three-step annealing conditions (200 °C for 12 h + 400 °C for 1 h + 500 °C for 5 min) without sputtering, after which the surface contamination of oxide and carbide was reduced to ∼20% of that before annealing. Clear GaN(0 0 0 1)1×1 patterns were obtained by LEED and RHEED. STM images showed flat terraces of ∼10 nm size and steps of ∼0.5 nm height. Upon annealing the HVPE-GaN samples at a much higher temperature (C), three-dimensional (3D) islands with facets were formed and the surface stoichiometry was broken down with the desorption of nitrogen in the form of ammonia, since the samples include hydrogen as an impurity. Ar⁺ sputtering was effective for removing surface contamination, however, postannealing could not recover the surface roughness but promoted the formation of 3D islands on the surface. For MOCVD/HVPE homoepitaxial samples, the surfaces are terminated by hydrogen and the as-introduced samples showed a clear 1×1 structure. Upon annealing at 500-600 °C, the surface hydrogen was removed and a 3×3 reconstruction structure partially appeared, although a 1×1 structure was dominant. We summarize the structure differences among the samples under the same treatment and clarify the effect of crystal quality, such as dislocations, the concentration of hydrogen impurities, and the residual reactant molecules in GaN films, on the surface structure.     

Atomistic mechanisms for the ordered growth of Co nanodots on Au(7 8 8): a comparison between VT-STM experiments and multi-scaled calculations

Hetero-epitaxial growth on a strain-relief vicinal patterned substrate has revealed unprecedented 2D long range ordered growth of uniform cobalt nanostructures. The morphology of a sub-monolayer Co deposit on a Au(1 1 1) reconstructed vicinal surface is determined by using variable temperature scanning tunneling microscopy (VT-STM). A rectangular array of nanodots (3.8 nm × 7.2 nm) is found for a particularly large deposit temperature range lying from 65 to 300 K. This paper focuses on the early stage of growth at temperatures between 35 and 480 K. Atomistic mechanisms leading to the nanodots array are elucidated by comparing statistical analysis of VT-STM images with multi-scaled numerical calculations. Molecular dynamics allows the quantitative determination of the activation energies for the atomic motion, whereas the kinetic Monte Carlo method simulates the submonolayer Co growth over mesoscopic time scale and space scale.     

Magnetic study of nanostructured zinc ferrite irradiated with 100 MeV O-beam

Nanostructured zinc ferrite of particle size 10 nm was synthesized by using the nitrates of appropriate cations and citric acid. This system was irradiated by 100 MeV oxygen beam with the fluence of 5×10¹³ ions/cm². The particle size of the system remains almost same after the irradiation. We observe decrease in magnetization of the sample after irradiation at 300 and 10 K. The nature of the σ-H plot shows the presence of superparamgnetic domains at 300 K even after irradiation. The blocking temperature decreases from 276 to 63 K after irradiation. The Mössbauer spectroscopy supports the presence of superparamgnetic domains at 300 K in both the samples. The decrease in magnetization after irradiation is attributed to the decrease in cation inversion and increase in canting angle as observed from in-field Mössbauer spectroscopy.     

Strain relaxation in nano-patterned strained-Si/SiGe heterostructure on insulator

In order to evaluate the strain stability, arrays of strained Si/SiGe nano-stripes and nano-pillars were fabricated by Electron-Beam Lithography (EBL) and Reactive-Ion Etching (RIE). The strain relaxation in the patterned strained Si on SiGe-on-insulator (SGOI) was investigated by high-resolution UV micro-Raman spectroscopy. The Raman measurements before and after patterning indicate that most of the strain in the top strained Si is maintained until scaling down to 300 nm, and relaxation of <15% is observed in pillars with a dimension of 150 nm × 150 nm. In the nano-patterned heterostructure strained Si/SiGe, the observed relaxation is small, which is mainly attributed to the fully relaxed and dislocation-free SiGe virtual substrate fabricated by modified Ge condensation.     

Characterizations of n-type ferromagnetic GaMnN thin film grown on GaN/Al2O3 (0 0 0 1) by metal-organic chemical vapor deposition

A high-quality ferromagnetic GaMnN (Mn=2.8 at%) film was deposited onto a GaN buffer/Al₂O₃(0 0 0 1) at 885 °C using the metal-organic chemical vapor deposition (MOCVD) process. The GaMnN film shows a highly c-axis-oriented hexagonal wurtzite structure, implying that Mn doping into GaN does not influence the crystallinity of the film. No Mn-related secondary phases were found in the GaMnN film by means of a high-flux X-ray diffraction analysis. The composition profiles of Ga, Mn, and N maintain nearly constant levels in depth profiles of the GaMnN film. The binding energy peak of the Mn 2p_3/2 orbital was observed at 642.3 eV corresponding to the Mn (III) oxidation state of MnN. The presence of metallic Mn clusters (binding energy: 640.9 eV) in the GaMnN film was excluded. A broad yellow emission around 2.2 eV as well as a relatively weak near-band-edge emission at 3.39 eV was observed in a Mn-doped GaN film, while the undoped GaN film only shows a near-band-edge emission at 3.37 eV. The Mn-doped GaN film showed n-type semiconducting characteristics; the electron carrier concentration was 1.2×10²¹/cm³ and the resistivity was 3.9×10⁻³ Ω cm. Ferromagnetic hysteresis loops were observed at 300 K with a magnetic field parallel and perpendicular to the ab plane. The zero-field-cooled and field-cooled curves at temperatures ranging from 10 to 350 K strongly indicate that the GaMnN film is ferromagnetic at least up to 350 K. A coercive field of 250 Oe and effective magnetic moment of 0.0003 μ_B/Mn were obtained. The n-type semiconducting behavior plays a role in inducing ferromagnetism in the GaMnN film, and the observed ferromagnetism is appropriately explained by a double exchange mechanism.     

Composition, morphology and surface recombination rate of HCl-isopropanol treated and vacuum annealed InAs(1 1 1)A surfaces

X-ray photoelectron spectroscopy and atomic force microscopy were used to examine the chemical composition and surface morphology of InAs(1 1 1)A surface chemically etched in isopropanol-hydrochloric acid solution (HCl-iPA) and subsequently annealed in vacuum in the temperature range 200-500 °C. Etching for 2-30 min resulted in the formation of “pits” and “hillocks” on the sample surface, respectively 1-2 nm deep and high, with lateral dimensions 50-100 nm. The observed local formations, whose density was up to 3 × 10⁸ cm⁻², entirely vanished from the surface after the samples were vacuum-annealed at temperatures above 300 °C. Using a direct method, electron beam microanalysis, we have determined that the defects of the hillock type includes oxygen and excessive As, while the “pits” proved to be identical in their chemical composition to InAs. Vacuum anneals were found to cause a decrease in As surface concentration relative to In on InAs surface, with a concomitant rise of surface recombination rate.