In situ hybridization to chitosan/magnetite nanocomposite induced by the magnetic field

Chitosan/magnetite nanocomposite was synthesized induced by magnetic field via in situ hybridization in ambient condition. Results of XRD patterns and TEM micrographs indicated that magnetite particles with 10–20 nm were dispersed in chitosan homogeneously. An interesting result is that magnetite nanoparticles were assembled to form chain-like structures under the influence of the external magnetic field, which mimics the magnetite chains inside of magnetotatic bacteria. The saturated magnetization (Ms) of nano-magnetite in chitosan was 50.54 emu/g, which is as high as 54% of bulk magnetite. The remanence (Mr) and coercivity (Hc) were 4 emu/g and14.8 Oe, respectively, which indicated that magnetite nanoparticles were superparamagnetic. The key of route is that a pre-precipitated chitosan hydrogel membrane, used as chemical reactor, which controlled the precipitation of chitosan precipitation and in situ transformation of magnetite from the precursor simultaneously in the magnetic field environment.     

Studies of magnetite nanoparticles synthesized by thermal decomposition of iron (III) acetylacetonate in tri(ethylene glycol)

In this paper, water-soluble magnetite nanoparticles have been directly synthesized by thermal decomposition of iron (III) acetylacetonate, Fe(acac)₃ in tri(ethyleneglycol). Size and morphology of the nanoparticles are determined by transmission electron microscopy (TEM) and dynamic light scattering (DLS) measurements while the crystal structure is identified using X-ray diffraction (XRD). Surface charge and surface coating of the nanoparticles are recognized using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectra (XPS) and zeta potential measurements. Magnetic properties are determined using vibrating sample magnetometer (VSM) and superconducting quantum interference device (SQUID) measurements. The results show that as-prepared magnetite nanoparticles are relatively monodisperse, single crystalline and superparamagnetic in nature with the blocking temperature at around 100 K. The magnetite nanoparticles are found to be highly soluble in water due to steric and electrostatic interactions between the particles arising by the surface adsorbed tri(ethyleneglycol) molecules and associated positive charges, respectively. Cytotoxicity studies on human cervical (SiHa), mouse melanoma (B16F10) and mouse primary fibroblast cells demonstrate that up to a dose of 80 μg/ml, the magnetic nanoparticles are nontoxic to the cells. Specific absorption rate (SAR) value has been calculated to be 885 and 539 W/gm for samples with the iron concentration of 1 and 0.5 mg/ml, respectively. The high SAR value upon exposure to 20 MHz radiofrequency signifies the applicability of as-prepared magnetite nanoparticles for a feasible magnetic hyperthermia treatment.     

Synthesis of iron oxide nanoparticles under oxidizing environment and their stabilization in aqueous and non-aqueous media

Synthesis of magnetite (Fe₃O₄) nanoparticles under oxidizing environment by precipitation from aqueous media is not straightforward because Fe²⁺ gets oxidized to Fe³⁺ and thus the ratio of Fe³⁺:Fe²⁺=2:1 is not maintained during the precipitation. A molar ratio of Fe³⁺:Fe²⁺ smaller than 2:1 has been used by many to compensate for the oxidation of Fe²⁺ during the preparation. In this work, we have prepared iron oxide nanoparticles in air environment by the precipitation technique using initial molar ratios Fe³⁺:Fe²⁺?2:1. The phases of the resulting powders have been determined by several techniques. It is found that the particles consist mainly of maghemite with little or no magnetite phase. The particles have been suspended in non-aqueous and aqueous media by coating the particles with a single layer and a bilayer of oleic acid, respectively. The particle sizes, morphology and the magnetic properties of the particles and the ferrofulids prepared from these particles are reported. The average particle sizes obtained from the TEM micrographs are 14, 10 and 9 nm for the water, kerosene and dodecane-based ferrofluids, respectively, indicating a better dispersion in the non-aqueous media. The specific saturation magnetization (σ_s) value of the oleic-acid-coated particles (∼53 emu/g) is found to be lower than that for the uncoated particles (∼63 emu/g). Magnetization σ_s of the dodecane-based ferrofluid is found to be 10.1 emu/g for a volume fraction of particles ?=0.019. Zero coercivity and zero remanance on the magnetization curves indicate that the particles are superparamagnetic (SPM) in nature.     

Magnetic and structural properties of CaO–SiO2–P2O5–Na2O–Fe2O3 glass ceramics

Magnetic properties of glass ceramics derived from glasses with composition 41CaO·(52−x)SiO₂·4P₂O₅·xFe₂O₃·3Na₂O (2?x?10 mol% iron oxide (Fe₂O₃)) are reported. Structural investigation revealed the presence of nanocrystalline magnetite phase in the heat-treated samples containing x?2 mol% Fe₂O₃. Magnetic hysteresis cycles of the glass-ceramic samples were obtained with a maximum applied field of ±20 kOe as well as a low field of ±500 Oe, in order to evaluate the potential of these glass ceramics for hyperthermia treatment of cancer. Samples with x>2 mol% of iron oxide exhibited magnetic behavior similar to soft magnetic materials with low coercivity. The evolution of magnetic properties in these samples as a function of iron oxide molar concentration is correlated with the amount and crystallite size of magnetite phase present in them.     

One-step hydrothermal synthesis of highly water-soluble secondary structural Fe3O4 nanoparticles

Magnetite nanoparticles (MNPs) were prepared using the ferric acetylacetonate as the sole iron source in a facile hydrothermal route, while poly(acrylic acid) (PAA) was chosen as the stabilizer via one-step functionalized MNPs for better hydrophilic properties. The orthogonal was used in the paper for the experimental parameters optimization, including the solvent, the reaction time, the amount of stabilizer and the presynthesis. The obtained highly water dispersible MNPs with uniform size from about 50 to about 100 nm was individually composed of many monodisperse magnetite crystallites approximately 6 nm in size. And the MNPs show high magnetic properties, whose magnetite content was up to 76.76% and the saturation magnetization was 39.0 emu/g. Later the formation mechanism of MNPs was also discussed. Thus the MNPs proved to be very promising for biomedical applications.     

Preparation of size-controlled nanoparticles of magnetite

Samples of ferrofluids containing chemically stabilized nanoparticles of magnetite (Fe₃O₄) with tetramethylammonium hydroxide (TMAOH) were prepared by a direct reduction–precipitation method. The influences of aging time and temperature on the size and monodispersion characteristics of the produced nanoparticles were investigated. Transmission electron microscopy, powder X-ray diffraction, Fourier-transform infrared, and magnetization measurements with applied magnetic field up to 2 T were used to characterize the synthesized iron oxides. Raising the temperature of the synthesized material in autoclave affects positively the monodispersion of the nanoparticles, but it was not found to significantly influence the size itself of individual particles.     

Improvement of corrosion resistance of nitrided low alloy steel by plasma post-oxidation

Post-oxidizing treatments can be performed to improve the corrosion resistance of nitrided steel samples. In this paper, plasma nitriding treatments were performed at 540 °C for 4 h using ammonia as the working gas, and plasma post-oxidizing treatments were carried out at temperatures ranging from 350 °C to 500 °C for 2 h in oxygen gas. The treated samples were characterized by using optical microscopy, SEM, XRD, and electrochemical polarization. The X-ray analysis revealed the formation of iron-nitride phases of ?-Fe_2-3N and γ′-Fe₄N during plasma nitriding and iron oxide phases of hematite (Fe₂O₃) and magnetite (Fe₃O₄) through the post-oxidizing treatment. In particular, it was found that the very thin magnetite layer 0.8-1.5 μm in thickness on top of the compound layer was obtained by plasma post-oxidized at 400 °C and 450 °C. It was also demonstrated that the corrosion characteristics of the nitrided compound layer were further improved by post-oxidation treatment.     

Infrared and Raman spectroscopic studies on iron oxide magnetic nano-particles and their surface modifications

Iron oxide magnetic nano-particles (MNPs) have been prepared in aqueous solution by a modified co-precipitation method. Surface modifications have been carried out using tetraethoxysilane (TEOS), triethoxysilane (TES) and 3-aminopropyltrimethoxysilane (APTMS). The uncoated and coated particle products have been characterized with transmission electron microscope (TEM), energy dispersive X-ray (EDX) spectroscopy, infrared (IR) and Raman spectroscopy, and thermal gravimetric analysis (TGA). The particle sizes were determined from TEM images and found to have mean diameters of 13, 16 and 14 nm for Fe₃O₄, TES/Fe₃O₄ and APTMS/Fe₃O₄, respectively. IR and Raman spectroscopy has been applied to study the effect of thermal annealing on the uncoated and coated particles. The results have shown that magnetite nano-particles are converted to maghemite at 109 °C and then to hematite by 500 °C. In contrast, the study of the effect of thermal annealing of micro-crystalline magnetite by IR spectroscopy revealed that the conversion to hematite began by 300 °C and that no maghemite could be identified as an intermediate phase. IR spectra and TGA measurements revealed that the Si-H and 3-aminopropyl functional groups in TES and APTMS coated magnetite nano-particles decomposed below 500 °C while the silica layer around the iron oxide core remained unchanged. The molecular ratio of APTMS coating to iron oxide core was determined to be 1:7 from the TGA data. Raman scattering signals have indicated that MNPs could be converted to maghemite and then to hematite using increasing power of laser irradiation in a manner similar to that observed for thermal annealing.     

The effect of aging time and calcination temperature on the magnetic properties of α-Fe/Fe3O4 composite

Composites of α-Fe/Fe₃O₄ having dimensions in the range of 100–150 nm have been prepared by disproportion method. The structure and morphology are investigated by XRD and TEM. XRD shows that the metal has got the BCC structure. TEM shows balls of metallic iron about 100-nm-wide stuck to magnetite grains. Magnetic measurement shows that the sample aged for 3 h and calcined at 200 °C has the maximal saturation magnetization corresponding to the highest concentration of α-Fe in the final sample.     

Novel magnetic Fe onion-like fullerene micrometer-sized particles of narrow size distribution

Magnetic polydivinylbenzene (PDVB)/magnetite micrometer-sized particles of narrow size distribution were prepared by entrapping Fe(CO)₅ within the pores of uniform porous PDVB particles, followed by the thermal decomposition of the encapsulated Fe(CO)₅ at 300 °C in a sealed cell under inert atmosphere. Magnetic Fe onion-like fullerene micrometer-sized particles of narrow size distribution have been prepared by the thermal decomposition of the PDVB/magnetite magnetic microspheres at 1100 °C under inert atmosphere. The graphitic coating protects the elemental iron particles from oxidation and thereby preserves their very high magnetic moment for at least a year. Characterization of these unique magnetic carbon graphitic particles was also performed.     

Production of magnetic microspheres by ultrasonic atomisation

Magnetic microspheres, with mean particle sizes from 23 to 32 μm were produced by the ultrasonic atomisation of a suspension of magnetite particles, of approximately 200 nm diameter, in a solution of poly–l–lactic acid (PLLA). The mean particle diameter and the width of the particle diameter distribution both increased with increasing magnetite concentration. The particles appear to be suitable for magnetic hyperthermic treatment of liver cancers, with the hysteresis loop areas increasing linearly with nominal magnetite concentration up to 30 wt% magnetite.     

Core-shell structure and magnetic properties of magnetite magnetic fluids stabilized with dextran

The adsorption process of different dextran molecules onto the surface of in water dispersed magnetite nanoparticles has been investigated to optimize the preparation of magnetite magnetic fluids (MMFs). An average magnetite core size of 7.1 nm was found by X-ray diffraction and that of 8 nm was found by transmission electron microscopy for the samples prepared at 90 °C. An average hydrodynamic diameter of 25 nm was observed by scanning electron microscopy and that of 25-300 nm was obtained by photon correlation spectroscopy. The dextran was adsorbed by physical adsorption, a molecular weight of 20 kDa gave the best stability of these MMFs. The shell layer of the particles was weakly negatively charged in buffer solutions of pH values between 5.5 and 9.5. The particles seem to be mainly stabilized by sterical repulsion. The maximum available saturation magnetization of the MMFs was 3.5 kA/m.     

Characterization of iron oxide layers using Auger electron spectroscopy

Metals can form several kinds of oxides. Iron forms wustite (FeO), magnetite (FeO + Fe₂O₃ or Fe₃O₄) and haematite (Fe₂O₃). Iron oxides, especially magnetite, are used for insulation between the lamellas of an electromotor made of electromagnetic sheet. In this work, iron oxide layers were characterized on industrial samples of electromagnetic sheet by AES depth profile analysis, and iron oxides with known chemical composition were used as reference samples, i.e. a magnetite mineral and a standard haematite reference sample. The magnetite mineral was chosen because it can be found in nature in a very pure form. The selection of reference samples was also verified on samples with an oxide layer of known composition, which were prepared by sputter deposition. The composition of the sputtered oxide layers was analysed by the weight-gain method and Rutherford backscattering without the use of standard reference materials (SRM), and the results were then compared with those obtained by AES depth profile analysis.     

Application of silica–magnetite nanocomposites to the isolation of ultrapure plasmid DNA from bacterial cells

The aim of this study was to develop a simple and rapid method for purification of ultrapure plasmid DNA with high yields from bacterial cultures. Nanosized superparamagnetic nanoparticles (Fe₃O₄) were prepared by chemical precipitation method using Fe²⁺, Fe³⁺ salt, and ammonium hydroxide under a nitrogen atmosphere. Silica–magnetite nanocomposites were prepared by the method of acid hydrolysis of tetraethoxysilane (TEOS) to coat the silica onto magnetite nanoparticles. DNA was adsorbed to the support under high salt conditions, and recovered directly in water for immediate downstream application, without the need for precipitation. We demonstrated that a useful plasmid, pRSETB-EGFP, encoding for the green fluorescent protein with T7 promoter, could be amplified in Escherichia coli of DE3 strain. Up to approximately 43 μg of high-purity (A₂₆₀/A₂₈₀ ratio=1.75) plasmid DNA was isolated from 3 ml of an overnight bacterial culture. The eluted plasmid DNA was used directly for restriction enzyme digestion, bacterial cell transformation and polymerase chain reaction (PCR) amplification with success. The protocol, starting from the preparation of bacterial lysate and ending with purified plasmid takes less than 8 min. The silica–magnetite nanocomposites deliver significant time-savings, overall higher yields, lower RNA contamination, and better PCR amplification compared to commercial available silica-based and other methods.     

Aligned carbon nanotubes catalytically grown on iron-based nanoparticles obtained by laser-induced CVD

Iron-based nanoparticles are prepared by a laser-induced chemical vapor deposition (CVD) process. They are characterized as body-centered Fe and Fe₂O₃ (maghemite/magnetite) particles with sizes ≤5 and 10 nm, respectively. The Fe particles are embedded in a protective carbon matrix. Both kind of particles are dispersed by spin-coating on SiO₂/Si(1 0 0) flat substrates. They are used as catalyst to grow carbon nanotubes by a plasma- and filaments-assisted catalytic CVD process (PE-HF-CCVD). Vertically oriented and thin carbon nanotubes (CNTs) were grown with few differences between the two samples, except the diameter in relation to the initial size of the iron particles, and the density. The electron field emission of these samples exhibit quite interesting behavior with a low turn-on voltage at around 1 V/μm.     

A Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) study of oleate adsorbed on magnetite nano-particle surface

Magnetite nano-particles were coated with sodium oleate and the spectral behaviour of the coating layer was studied by FTIR spectroscopy after the particles had been heated in air and argon. Magnetite was synthesized by controlled co-precipitation and subsequently coated with sodium oleate. Thermal analysis in combination with mass spectroscopy was carried out to support the FTIR spectroscopic interpretations, but also to monitor the decomposition and surface reaction of oleate adsorbed on the magnetite surface. It was deduced from FTIR and TGA results that the oleate molecules are bonded to iron atoms by a bidentate mononuclear complex and form essentially a single layer with a distance between oleate molecules of ∼36 Å². It was shown by IR as well as Raman spectroscopy that oleic acid, when heated in air, undergoes decomposition implying that new carbon-oxygen bonds are formed. Heating the iron oxide-oleate system in air also implies oxidation of the double bond at the C:9 position of the alkyl chain and formation of intermediate oxygen-rich molecules. An enthalpy change of ΔH = 49.86 J/g was obtained for oleate desorption/decomposition at ∼350 °C under argon atmosphere and a carbonaceous graphitic species resulted from this decomposition.     

Biodegradable nanocomposite magnetite stent for implant-assisted magnetic drug targeting

This study shows, for the first time, the fabrication of a biodegradable polymer nanocomposite magnetic stent and the feasibility of its use in implant-assisted-magnetic drug targeting (IA-MDT). The nanocomposite magnetic stent was made from PLGA, a biodegradable copolymer, and iron oxide nanopowder via melt mixing and extrusion into fibers. Degradation and dynamic mechanical thermal analyses showed that the addition of the iron oxide nanopowder increased the polymer’s glass transition temperature (T_g) and its modulus but had no notable effect on its degradation rate in PBS buffer solution. IA-MDT in vitro experiments were carried out with the nanocomposite magnetic fiber molded into a stent coil. These stent prototypes were used in the presence of a homogeneous magnetic field of 0.3 T to capture 100 nm magnetic drug carrier particles (MDCPs) from an aqueous solution. Increasing the amount of magnetite in the stent nanocomposite (0, 10 and 40 w/w%) resulted in an increase in the MDCP capture efficiency (CE). Reducing the MDCP concentrations (0.75 and 1.5 mg/mL) in the flowing fluid and increasing the fluid velocities (20 and 40 mL/min) both resulted in decrease in the MDCP CE. These results show that the particle capture performance of PLGA-based, magnetic nanocomposite stents are similar to those exhibited by a variety of different non-polymeric magnetic stent materials studied previously.     

Preparation of hydrophilic magnetic nanospheres with high saturation magnetization

Well-defined silica-magnetite core-shell nanospheres were prepared via a modified sol–gel method. Sphere-like magnetite aggregates were obtained as cores of the final nanospheres by assembling in the presence of Tween 20. Characterization by transmission electron microscopy (TEM) showed spherical morphology of the nanospheres with controlled silica shell thickness from 9 to 30 nm, depending on the amount of tetraethoxysilane (TEOS) used. The nanospheres contained up to 41.7 wt% magnetite with a saturation magnetization of 21.8 emu/g. Up to 35 μg/mg of the model biomolecule streptavidin (SA) could be bound covalently to the hydrophilic silica nanospheres.     

Intra-well relaxation process in magnetic fluids subjected to strong polarising fields

We report on the frequency and field dependent complex magnetic susceptibility measurements of a kerosene-based magnetic fluid with iron oxide nanoparticles, stabilized with oleic acid, in the frequency range 0.1-6 GHz and over the polarising field range of 0-168.4 kA/m.By increasing polarising field, H, a subsidiary loss-peak clearly occurs in the vicinity of the ferromagnetic resonance peak, from which it remains distinct even in strong polarising fields of 168.4 kA/m. This is in contrast to other reported cases in which the intra-well relaxation process is manifested only as a shoulder of the resonance peak, which vanishes in polarising fields larger than that of 100 kA/m.The results of the XRD analysis connected to the anisotropy field results confirm that the investigated sample contains particles of magnetite and of the tetragonal phase of maghemite.Taking into account the characteristics of our sample, the theoretical analysis revealed that the intra-well relaxation process of the small particles of the tetragonal phase of maghemite may be responsible for the subsidiary loss peak of the investigated magnetic fluid.     

In vitro study of magnetic particle seeding for implant assisted-magnetic drug targeting

The concept of using magnetic particles (seeds) as the implant for implant assisted-magnetic drug targeting (IA-MDT) was analyzed in vitro. Since this MDT system is being explored for use in capillaries, a highly porous (ε∼70%), highly tortuous, cylindrical, polyethylene polymer was prepared to mimic capillary tissue, and the seeds (magnetite nanoparticles) were already fixed within. The well-dispersed seeds were used to enhance the capture of 0.87 μm diameter magnetic drug carrier particles (MDCPs) (polydivinylbenzene embedded with 24.8 wt% magnetite) under flow conditions typically found in capillary networks. The effects of the fluid velocity (0.015–0.15 cm/s), magnetic field strength (0.0–250 mT), porous polymer magnetite content (0–7 wt%) and MDCP concentration (C=5 and 50 mg/L) on the capture efficiency (CE) of the MDCPs were studied. In all cases, when the magnetic field was applied, compared to when it was not, large increases in CE resulted; the CE increased even further when the magnetite seeds were present. The CE increased with increases in the magnetic field strength, porous polymer magnetite content and MDCP concentration. It decreased only with increases in the fluid velocity. Large magnetic field strengths were not necessary to induce MDCP capture by the seeds. A few hundred mT was sufficient. Overall, this first in vitro study of the magnetic seeding concept for IA-MDT was very encouraging, because it proved that magnetic particle seeds could serve as an effective implant for MDT systems, especially under conditions found in capillaries.