Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Adsorption behavior of <Superscript>99</Superscript>Tc on Fe,Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Summary The adsorption of ⁹⁹Tc on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ was studied by batch experiments under aerobic and anoxic conditions. The effects of pH and CO₃^2- concentration of the simulated ground water on the adsorption ratios were also investigated, and the valences of Tc in solution after the adsorption equilibrium were studied by solvent extraction. The adsorption isotherms of TcO₄- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ were determined. Experimental results have shown that the adsorption ratio of Tc on Fe decreases with the increase of pH in the range of 5-12 and increases with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M. Under aerobic conditions, the adsorption ratios of ⁹⁹Tc on Fe₂O₃ and Fe₃O₄ were not influenced by pH and CO₃^2-concentration. When Fe was used as adsorbent, Tc existed mainly in the form of Tc(IV) after equilibrium and in the form of Tc(VII) when the adsorbent was Fe₂O₃ or Fe₃O₄ under aerobic conditions. The adsorption ratios of Tc on Fe, Fe₂O₃ and Fe₃O₄ decreased with the increase of pH in the range of 5-12 and increased with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M under anoxic conditions. Tc existed mainly in the form of Tc(IV) after equilibrium when Fe, Fe₂O₃ and Fe₃O₄ was the adsorbent under anoxic conditions. The adsorption isotherms of TcO_4- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ are fairly in agreement with the Freundlich’s equation under both aerobic and anoxic conditions.     

Solubility in the ternary system CaSO<Subscript>4</Subscript> + Na<Subscript>2</Subscript>SO<Subscript>4</Subscript> + H<Subscript>2</Subscript>O at 298.15 K

The solubility in the ternary system, aqueous mixture of CaSO₄ and Na₂SO₄, at T = 298.15 K comprises five different salts: calcium sulfate dihydrate, mirabilite, thenardite, glauberite and labile salt. Using the Extended Pitzer’s Ion Interaction model for pure and mixed electrolyte solutions and criteria of phase equilibria, predicted solubility behavior of salts was compared with experimental results from literature. The agreement between calculated and experimental solubilities was excellent in the ionic strength range up to 10.9062 mol kg⁻¹.     

Crystallization and Phase Stability of CaSO<Subscript>4</Subscript> and CaSO<Subscript>4</Subscript> – Based Salts

Summary.  Calcium sulfate occurs in nature in form of three different minerals distinguished by the degree of hydration: gypsum (CaSO₄·2H₂O), hemihydrate (CaSO₄·0.5H₂O) and anhydrite (CaSO₄). On the one hand the conversion of these phases into each other takes place in nature and on the other hand it represents the basis of gypsum-based building materials. The present paper reviews available phase diagram and crystallization kinetics information on the formation of calcium sulfate phases, including CaSO₄-based double salts and solid solutions. Uncertainties in the solubility diagram CaSO₄–H₂O due to slow crystallization kinetics particularly of anhydrite cause uncertainties in the stable branch of crystallization. Despite several attempts to fix the transition temperatures of gypsum–anhydrite and gypsum–hemihydrate by especially designed experiments or thermodynamic data analysis, they still vary within a range from 42–60°C and 80–110°C. Electrolyte solutions decrease the transition temperatures in dependence on water activity. Dry or wet dehydration of gypsum yields hemihydrates (α-, β-) with different thermal and re-hydration behaviour, the reason of which is still unclear. However, crystal morphology has a strong influence. Gypsum forms solid solutions by incorporating the ions HPO₄ ²⁻, HAsO₄ ²⁻, SeO₄ ²⁻, CrO₄ ²⁻, as well as ion combinations Na⁺(H₂PO₄)⁻ and Ln³⁺(PO₄)³⁻. The channel structure of calcium sulfate hemihydrate allows for more flexible ion substitutions. Its ion substituted phases and certain double salts of calcium sulfate seem to play an important role as intermediates in the conversion kinetics of gypsum into anhydrite or other anhydrous double salts in aqueous solutions. The same is true for the opposite process of anhydrite hydration to gypsum. Knowledge about stability ranges (temperature, composition) of double salts with alkaline and alkaline earth sulfates (esp. Na₂SO₄, K₂SO₄, MgSO₄, SrSO₄) under anhydrous and aqueous conditions is still very incomplete, despite some progress made for the systems Na₂SO₄–CaSO₄ and K₂SO₄–CaSO₄–H₂O. Corresponding author. E-mail: daniela.freyer@chemie.tu-freiberg.de Received December 17, 2002; accepted January 10, 2003 Published online April 3, 2003     

Extraction of metal ions (Fe<Superscript>3+</Superscript>, Co<Superscript>2+</Superscript>, Ni<Superscript>2+</Superscript>, Cu<Superscript>2+</Superscript> and Zn<Superscript>2+</Superscript>) using immobilized-polysiloxane iminobis(n-2-aminophenylacetamide) ligand system

A new insoluble solid functionalized ligand system bearing chelating ligand group of the general formula P-(CH₂)₃-N[CH₂CONH(C₆H₄)NH₂]₂, where P represents [Si–O] _n polysiloxane network, was prepared by the reaction of the immobilized diethyliminodiacetate polysiloxane ligand system, P-(CH₂)₃N(CH₂CO₂Et)₂ with 1,2-diaminobenzene in toluene. ¹³C CP-MAS NMR, XPS and FTIR results showed that most ethylacetate groups (–COOEt) were converted into the amide groups (–N–C=O). The new functionalized ligand system exhibits high capacity for extraction and removal of the metal ions (Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺ and Zn²⁺) with efficiency of 95–97% after recovery from its primary metal complexes. This functionalized ligand system formed 1:1 metal to ligand complexes.     

Heat capacity and magnetic phase transition of two-dimensional metal-assembled complex (NEt<Subscript>4</Subscript>)[{Mn<Superscript>III</Superscript>(salen)}<Subscript>2</Subscript>Fe<Superscript>III</Superscript>(CN)<Subscript>6</Subscript>]

Summary Heat capacity measurements of the two-dimensional metal-assembled complex, (NEt₄)[{Mn^III(salen)}₂Fe^III(CN)₆] [Et=ethyl, salen= N,N’-ethylenebis(salicylideneaminato) dianion], were performed in the temperature range between 0.2 and 300 K by adiabatic calorimetry. A ferrimagnetic phase transition was observed at T_c1=7.51 K. Furthermore, another small magnetic phase transition appeared at T_c2=0.78 K. Above T_c1, a heat capacity tail arising from the short-range ordering of the spins characteristic of two-dimensional magnets was found. The magnetic enthalpy and entropy were evaluated to be ΔH=291 J mol^-1 and ΔS=27.4 J K^-1 mol^-1, respectively. The experimental magnetic entropy agrees roughly with ΔS=Rln(5·5·2) (=32.5 J K^-1 mol^-1; R being the gas constant), which is expected for the metal complex with two Mn(III) ions in high-spin state (spin quantum number S=2) and one Fe(III) ion in low-spin state (S=1/2). The heat capacity tail above T_c1 became small by grinding and pressing the crystal. This mechanochemical effect would be attributed to the increase of lattice defects and imperfections in the crystal lattice, leading not only to formation of the crystal with a different magnetic phase transition temperature but also to decrease of the magnetic heat capacity and thus the magnetic enthalpy and entropy.     

UV excited green luminescence of SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Dy<Superscript>3+</Superscript> nanophosphor

Eu, Dy co-doped strontium aluminate nanophosphors were prepared by the combustion synthesis method. Their structure and morphology were investigated by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy. According to the XRD and the TEM analysis, the average crystallite size was found to be in the nanometer range. The phase structure of the prepared nanophosphor is consistent with a standard monoclinic phase with a space group P2₁. The prepared SrAl₂O₄:Eu²⁺, Dy³⁺ nanophosphor emitted green light with a peak at 510 nm showing blue shift, which is due to the reduction in the particle size. Two distinct peaks were observed in the ML intensity versus time curve. The two peaks in ML indicate the presence of charge transfer in an ML process.     

Synthesis,structure formation,and thermal expansion of A<Superscript>+</Superscript>M<Superscript>2+</Superscript>MgE<Superscript>4+</Superscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The compounds AMMgE(PO₄)₃ (A = Na, K, Rb, Cs; M = Sr, Pb, Ba; E = Ti, Zr) were synthesized by the sol–gel procedure followed by heat treatment and studied by X-ray diffraction, differential thermal and electron microprobe analysis, and IR spectroscopy. The phosphates crystallize in the kosnarite (KZr₂(PO₄)₃, space group \(R\bar 3\)) and langbeinite (K₂Mg₂(SO₄)₃, space group P2₁3) structural types. The structure of KPbMgTi(PO₄)₃ was refined by full-profile analysis (space group P2₁3, Z = 4, a = 9.8540(3) Å, V = 956.83(4) ų). The structure is formed by a framework of vertex-sharing MgO₆ and TiO₆ octahedra and PO₄ tetrahedra. The K and Pb atoms fully occupy the extra-framework cavities and are coordinated to nine oxygen atoms. A variable-temperature X-ray diffraction study of KPbMgTi(PO₄)₃ showed that the compound expands isotropically and refer to medium-expansion class (linear thermal expansion coefficients α _a = α _b = α _c = 8 × 10^–6°C^–1). The number of stretching and bending modes of the PO₄ tetrahedron observed in the IR spectra is in agreement with that predicted by the factor group analysis of vibrations for space groups \(R\bar 3\) and P2₁3. A structural transition from the cubic langbeinite to the rhombohedral kosnarite was found for CsSrMgZr(PO₄)₃. In the morphotropic series of ASrMgZr(PO₄)₃ (A = Na, K, Rb, Cs) the kosnarite–langbeinite transition occurs upon the Na → K replacement. The effect of the sizes and electronegativities of cations combined in AMMgE(PO₄)₃ on the change of the structural type was analyzed.     

Formation of coordination compounds with aniline in the interlayer space of Ca<Superscript>2+</Superscript>-, Cu<Superscript>2+</Superscript>- and Fe<Superscript>3+</Superscript>-exchanged montmorillonite

The influence of Ca²⁺-, Cu²⁺- and Fe³⁺-exchanged montmorillonite (MMT) on the type of interaction with aniline in the interlayer space of MMT has been studied by means of X-ray powder diffraction and infrared spectra. Results of X-ray diffraction showed that aniline was successfully intercalated into the interlayer space of MMT. Based on IR spectra evaluation, aniline was indirectly coordinated through a water-bridge in Ca²⁺- and Fe³⁺-MMT and it was indirectly coordinated through a water-bridge as well as protonated in Cu²⁺-MMT (the spectrum of protonated aniline showed deformation and changes in the NH ₃ ⁺ absorption at approximately 1521 cm^?1). It is important to point out that Cu²⁺-MMT indirect coordination and protonation occur simultaneously.     

In situ synthesis of MnO<Subscript>2</Subscript>-loaded biocomposite based on microcrystalline cellulose for Pb<Superscript>2+</Superscript> removal from wastewater

We fabricated a new MnO₂-loaded biocomposite based on microcrystalline cellulose (MCC–MnO₂) by an in situ synthesis method and investigated its adsorption behavior and mechanism for Pb²⁺ removal from aqueous medium. As-prepared MCC–MnO₂ was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) analyses. The effects of pH value, initial Pb²⁺ concentration, contact time, and solution temperature on the uptake of Pb²⁺ onto MCC–MnO₂ were investigated using a batch system. Adsorption equilibrium could be achieved in 3 h for various studied initial concentrations, and a pseudo-second-order model could fit the adsorption behavior well. The equilibrium data could be well described by the Langmuir isotherm model, and the maximum monolayer adsorption capacity of MCC–MnO₂ (with 7.98% MnO₂ loading) for Pb²⁺ was estimated to be 247.5 mg/g at 313 K. Thermodynamic studies indicated a spontaneous and endothermic adsorption process. X-ray photoelectron spectroscopy (XPS) was used to analyze the adsorption mechanism, revealing that the chemical speciation of Pb²⁺ on MCC–MnO₂ was similar to the compound PbO. Moreover, no variations in the valence of Mn were observed after adsorbing Pb²⁺. The regeneration study showed that the adsorption capacity retained about 89.6% of its initial value at the fifth sequential regeneration cycle, indicating that this material is an efficient and renewable hybrid adsorbent for Pb²⁺ removal.     

Selective extraction of Fe<Superscript>3+</Superscript> ions from Fe<Superscript>3+</Superscript>-Zn<Superscript>2+</Superscript> mixture with phosphate sorbents

The absorption of Fe³⁺ ions from Fe³⁺-Zn²⁺ mixture with zinc and calcium phosphates was studied.     

Synthesis and Characterization of New Os<Subscript>2</Subscript><Superscript>5+</Superscript> and Os<Subscript>2</Subscript><Superscript>6+</Superscript> Azido Complexes

Reaction of Os₂(OAc)₄Cl₂ with an excess of HDPhF (HDPhF = N,N′-diphenylformamidine) gives a high yield of Os₂(DPhF)₄Cl₂ (1), which can be converted to its azido analog, Os₂(DPhF)₄(N₃)₂ (3), by treatment with NaN₃. We report a major improvement on the preparation of Os₂(chp)₄Cl (2; Hchp = 2-chloro-6-hydroxypyridine) by synthesizing the compound in the reducing solvent ethanol. Reaction of 2 with NaN₃ affords the azido complex Os₂(chp)₄N₃ (4). Compound 3 has been examined by X-ray crystallography, and has an Os–Os bond distance of 2.45 Å, suggesting a (π*)² ground state for the molecule.     

Complex formation of maleic acid with the Zn<Superscript>2+</Superscript>, Ni<Superscript>2+</Superscript>, Co<Superscript>2+</Superscript>, Cu<Superscript>2+</Superscript> in aqueous solution

The process of complex formation of maleic acid (H₂L) with the ions Zn²⁺, Ni²⁺, Co²⁺, Cu²⁺ was studied by potentiometric titration in a wide range of concentration ratios at 298 K and I = 0.1 mol/l (NaNO₃). The moieties ZnL, CoL, NiL, NiL ₂ ^2? , CuL, and CuL ₂ ^2? were detected and their stability constants were determined.     

Synthesis of novel magnetic sulfur-doped Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles for efficient removal of Pb(II)

In this work, we report the synthesis of magnetic sulfur-doped Fe₃O₄ nanoparticles (Fe₃O₄:S NPs) with a novel simple strategy, which includes low temperature multicomponent mixing and high temperature sintering. The prepared Fe₃O₄:S NPs exhibit a much better adsorption performance towards Pb(II) than bare Fe₃O₄ nanoparticles. FTIR, XPS, and XRD analyses suggested that the removal mechanisms of Pb(II) by Fe₃O₄:S NPs were associated with the process of precipitation (formation of PbS), hydrolysis, and surface adsorption. The kinetic studies showed that the adsorption data were described well by a pseudo second-order kinetic model, and the adsorption isotherms could be presented by Freundlich isotherm model. Moreover, the adsorption was not significantly affected by the coexisting ions, and the adsorbent could be easily separated from water by an external magnetic field after Pb(II) adsorption. Thus, Fe₃O₄:S NPs are supposed to be a good adsorbents for Pb(II) ions in environmental remediation.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>composite particles

Using Fe₃O₄ nano-particles as seeds, a new type of Fe₃O₄/Au composite particles with core/shell structure and diameter of about 170 nm was prepared by reduction of Au³⁺ with hydroxylamine in an aqueous solution. Particle size analyzer and transmission electron microscope were used to analyze the size distribution and microstructure of the particles in different conditions. The result showed that the magnetically responsive property and suspension stability of Fe₃O₄ seeds as well as reduction conditions of Au³⁺to Au⁰are the main factors which are crucial for obtaining a colloid of the Fe₃O₄/Au composite particles with uniform particle dispersion, excellent stability, homogeneity in particle sizes, and effective response to an external magnet in aqueous suspension solutions. UV-Vis analysis revealed that there is a characteristic peak of Fe₃O₄/Au fluid. For particles with d(0.5)=168 nm, the λmax is 625 nm.     

Synthesis and characterization of novel magnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/polyurethane foam composite applied to the carrier of immobilized microorganisms for wastewater treatment

The objective of this work was to prepare novel magnetic Fe₃O₄/polyurethane foam (Fe₃O₄/PUF) composites applied to the carriers of immobilized microorganisms for toluene-containing wastewater treatment. The morphology and structure of Fe₃O₄/PUF composite were characterized by X-ray diffraction, Fourier transform IR spectroscopy, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, and magnetic property measurement system. These morphological investigations revealed that Fe₃O₄ nano-particles were well dispersed into the matrix of PUF with nano-scale diameter particles. TG experiments indicated that the initial thermal weight loss temperatures of composite with the content of 2.5 wt% and 7.5% Fe₃O₄ were increased by 7 and 16 °C, compared with pure PUF. The degradation efficiency of toluene with magnetic PUF composite was much higher than that of pure PUF carrier, and the reason why the immobilization of microbial biomass of microorganisms on the magnetic PUF composite was much higher than that of the pure PUF. The prepared magnetic Fe₃O₄/PUF composite offered excellent thermal stability and medium paramagnetic properties. And this composite could not only increase the immobilized biomass of the microorganisms, but also enhance the COD removal efficiency of wastewater.     

Characterization of nano-iron oxyhydroxides and their application in UO<Subscript>2</Subscript><Superscript>2+</Superscript> removal from aqueous solutions

The nano-iron oxyhydroxides (α- and γ-FeOOH) were synthesized by using three ferrous and ferric salts (FeSO₄, FeCl₂, Fe(NO₃)₃) as iron precursors under alkaline conditions. Morphologies of nano-iron oxyhydroxides were characterized by employing X-ray powder diffraction (XRD) and specific surface area (SSA) analysis respectively. The occurrence of needle-like shape of nano-goethite and rod-like shape of nano-lepidocrocite were attributed to hydrolysis of Fe³⁺ cations and/or oxidization of Fe²⁺ at alkaline conditions in terms of XRD analysis. The N₂-BET SSA and BJH (Barrett–Joyner–Halenda) pore size analysis showed that internal SSA of nano-lepidocrocite is higher than that of nano-goethite, although they have similar N₂-BET SSAs. The distribution of average pore size of nano-iron oxyhydroxides are higher than that of predominant pore size due to formation of the heterogeneous nanoparticles under the experimental conditions. These nanoparticles possess the high sorption capacity and the strong affinity for contaminants. Application of nano-iron oxyhydroxides in environmental engineering plays an important role to remove a variety of contaminants, such as heavy-metal ions and organic pollutants.     

Specific features of absorption of Cu<Superscript>2+</Superscript>, Zn<Superscript>2+</Superscript>, Co<Superscript>2+</Superscript>, and Pb<Superscript>2+</Superscript> cations from aqueous solutions by calcium phosphates

Kinetic characteristics of the interaction of trisubstituted calcium phosphate Ca₃(PO₄)₂ · xH₂O with Cu²⁺, Zn²⁺, Co²⁺, and Pb²⁺ ions in aqueous solutions were studied.     

Electrodeposition of thin Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> films

The electrochemical behavior of copper(II), zinc(II), and thiosulfate (S₂O₃ ^2-) ions on the molybdenum electrode in individual 0.2 М sodium sulfate solutions (рН 6.7) and with addition of either 0.1 М tartaric acid (рН 4.6) or 0.1 М citric acid (рН 4.7) is studied. A one-step electrochemical method is developed for the deposition of thin Cu₂ZnSnS₄ films, which is carried out on the molybdenum electrode at a constant potential in sodium sulfate solutions containing tartaric acid. The effect of the concentration of electrolyte components on the chemical composition of Cu₂ZnSnS₄ films is determined. The phase composition is confirmed by the Raman spectroscopy data. The surface morphology of synthesized films is studied by means of scanning-electron and atomic-force microscopes. The photoelectrochemical characteristics of Cu₂ZnSnS₄ films are determined. Samples of these coatings on the Mo electrode are found to be highly photosensitive.