碳纳米管的氧化铝模板法合成及其退火效应研究

结合氧化铝模板制约生长技术和高温退火处理，得到了相当统一的多壁碳纳米管.扫描电子显微镜（SEM）图像表明模板制约生长的初始碳纳米管形貌和尺寸完全受控于模板结构，透 射电子显微镜（TEM）和x射线粉末衍射（XRD）结果显示其管壁结构为无定形碳和石墨纳米 晶组成的混杂结构.为减少晶格缺陷及无定形碳，对初始碳纳米管进行系列高温（1100—240 0℃）退火处理，并初步研究了管壁在高温下的晶化行为.实验证明高温退火是提高多壁碳纳 米管质量的有效途径. 关键词： 氧化铝模板 碳纳米管 高温退火     

银纳米粒子修饰三维碳纳米管阵列SERS实验

为了使表面增强拉曼散射(SERS)基底的三维聚焦体积内包含更多的“热点”,能吸附更多探针分子和金属纳米颗粒,以便获得更强的拉曼光谱信号,提出了银纳米粒子修饰垂直排列的碳纳米管阵列三维复合结构作为SERS基底,并对其进行了实验研究。利用化学气相沉积(CVD)方法制备了垂直排列的碳纳米管阵列;采用磁控溅射镀膜方法先在碳纳米管阵列上形成一层银膜,再通过设置不同的高温退火温度,使不同粒径的银纳米粒子沉积在垂直有序排列碳纳米管阵列的表面和外壁。SEM结果表明：在有序碳纳米管阵列的表面和外壁都均匀地负载了大量银纳米粒子,并且银纳米颗粒的粒径、形貌及颗粒间的间距随退火温度的不同而不同。采用罗丹明6G(R6G)分子作为探针分子,拉曼实验结果表明：R6G浓度越高,拉曼强度越强,但是R6G浓度的增加与拉曼强度增强并不呈线性变化;退火温度为450 ℃,银纳米颗粒平均粒径在100～120 nm左右,退火温度为400 ℃,银纳米颗粒平均粒径在70 nm左右,退火温度为450 ℃的拉曼信号强度优于退火温度400和350 ℃。     

高压退火对碳纳米管微结构转变的影响

利用高分辨电子显微镜研究了在高压退火条件下碳纳米管的微结构变化规律，发现在5.5GPa下，770℃退火后即发生了明显的结构改变；在950℃退火25min后发现形成了类碳纳米洋葱和纳米碳条带结构.碳纳米管转变成类碳纳米洋葱可以分成几个步骤，首先碳纳米管破裂，然后形成碳纳米球，最后形成类碳纳米洋葱结构.讨论了高压和退火温度对碳纳米管结构变化的影响. 关键词：     

新型氧化铝模板自组装制备非晶碳纳米点阵列膜及其场发射性能研究

通过对阳极氧化铝(AAO)模板进行特殊扩孔处理,消除了AAO模板中带电阴离子对沉积碳离子的不良影响,利用磁过滤阴极弧等离子体沉积技术成功制备了非晶碳纳米尖点阵列膜.场发射扫描电镜(FESEM)分析表明,经过氧化和扩孔多步处理制备的AAO模板具有特殊的开口结构,制备的非晶碳纳米尖点阵列完整地复制了AAO模板的孔道阵列结构,纳米点排列整齐有序,直径约100nm,密度达1010cm-2,样品的场发射测试显示,非晶碳纳米点阵列具有良好的电子发射性能,发射电流为10mA/cm-2时的阈值电场为3.7V/μm.     

不同退火条件对纳米多孔氧化铝薄膜光致发光的影响

以草酸为电解液,采用二次阳极氧化法制备出了纳米多孔氧化铝薄膜,经不同退火温度和退火气氛处理氧化铝薄膜后,通过分析其光致发光光谱得出：相同的退火气氛中, 退火温度T≤600 ℃ 时,T=500 ℃具有最大的光致发光强度;退火温度T≥700 ℃时,随着退火温度的升高,样品的发光强度增大。在不同的退火气氛中,多孔氧化铝薄膜随着退火温度的升高,发光峰位改变不同,即在空气中退火处理后,随着退火温度的升高,发光峰位蓝移,而在真空中退火处理后,发光峰位并不随退火温度的升高而变化;通过对1 100 ℃高温退火处理后的氧化铝薄膜的光致发光曲线的高斯拟合,可以看出,经退火处理后的多孔氧化铝,主要存在三个发光中心,发光曲线在350～600 nm范围内对应三个发射峰, 发射波长分别为387,410,439 nm。相同的退火温度下,空气中退火得到的氧化铝薄膜的光致发光强度大于真空中退火处理后的氧化铝薄膜。基于实验结果,结合X射线色散能谱(EDS)、红外反射光谱等表征手段,探讨了多孔氧化铝薄膜的发光机制,并对经过不同退火条件得到的多孔氧化铝薄膜的光致发光特性的改变做出了合理的解释。     

阵列碳纳米管的石墨化程度

采用化学气相沉积法制备了阵列碳纳米管薄膜,对阵列碳纳米管的石墨化程度进行了系统研究。利用扫描电子显微镜(SEM)、拉曼光谱(Raman)对样品形貌以及结构进行了表征。探讨了不同实验参数对阵列碳纳米管石墨化程度影响的机理。结果发现,在一定催化剂浓度范围内,催化剂浓度过低时,阵列碳纳米管的石墨化程度较差,而随着催化剂浓度的增加,阵列碳纳米管的石墨化程度逐渐变好;生长石墨化程度较好的阵列碳纳米管需要合适的进液速度,进液速度过低或过高都会使得碳纳米管的石墨化程度变差;此外,生长石墨化程度较好的阵列碳纳米管也需要合适的生长温度,生长温度过低或过高都会使得碳纳米管的石墨化程度变差。     

超长定向含铁多壁碳纳米管阵列的制备

采用无模板化学气相沉积法,以二茂铁为催化剂,二甲苯为碳源,利用单温炉加热装置制备了定向碳纳米管阵列。运用扫描电子显微镜、透射电子显微镜、拉曼光谱和X射线衍射仪等对定向碳纳米管阵列的形貌、成分和物相进行细致的分析和表征。结果表明:制得的碳纳米管阵列具有良好的定向性和多壁管状结构,并且石墨化程度高;碳纳米管中除碳元素外,管中包含有少量以纳米颗粒和纳米线形式存在的铁及其化合物,主要成分是铁和碳化铁。结合碳纳米管的制备和透射电子显微镜分析表征结果,认为超长碳纳米管阵列的生长模式为底部生长方式,即经历催化剂分解、催化、成核、长大、中毒、凝聚成粒和连接成线的循环过程,正是由于碳源和催化剂的连续供应促成了碳纳米管阵列的快速定向生长。     

CoPt(FePt)-C纳米复合膜的结构与磁性

用磁过滤脉冲真空电弧沉积方法制备了CoPt(FePt) C纳米复合薄膜，并在不同温度下进行了退火处理，研究了薄膜中碳的含量以及退火温度对薄膜结构与磁性能的影响.制备态薄膜经过足够高的温度退火后，x射线衍射和磁力显微镜分析发现，在碳基质中生成了面心四方相的CoPt(FePt)纳米颗粒.对于特定组分为Co24Pt31C45和Fe43Pt35C22的薄膜，矫顽力以及颗粒尺寸都随退火温度的升高而增大，当退火温度为700℃时，Co24Pt31C45薄膜的矫顽力为21×105A/m，晶粒尺寸为17nm;当退火温度为650℃时，Fe43Pt35C22相应值分别为28×105A/m和105nm. 关键词： 磁记录材料 磁性薄膜 CoPt FePt纳米复合薄膜     

连续碳纳米管线及其应用

如何将碳纳米管组装成宏观尺度的结构对于碳纳米管的宏观应用来说具有重要意义．自从碳纳米管被发现以来，在合成大面积碳纳米管阵列方面已经取得很多的进展，并有望应用于场发射平板显示器．然而，在如何将碳纳米管顺排起来连成连续的长线方面则鲜有进展．这里介绍的是作者最近的新发现：当从一种作者称之为“超顺排”碳纳米管阵列中拔出一束碳纳米管时，碳纳米管以可自组织成一条连续的长线．在这个过程中，“超顺排”碳纳米管阵列起的作用如同一个蚕茧，阵列中的碳纳米管则由范德瓦耳斯力首尾相连形成连续的纯碳纳米管线．这种碳纳米管线平行排列起来构成的偏振片可以工作在紫外波段．这种碳纳米管线还可以用作白炽灯的灯丝，仅需很小的功率就可以发出白炽光．不仅如此，这种碳纳米管线经过高温处理后，强度和导电性都得到明显增强，这将使碳纳米管线在宏观领域内得到更多的应用．     

不同退火温度下晶化硅薄膜的电学输运性质

采用等离子体化学气相沉积技术制备氢化非晶硅薄膜,经过不同温度下的热退火处理,使薄膜由非晶结构向晶化结构转变,得到含有纳米晶粒的晶化硅薄膜.在晶化过程中,采用Raman技术对样品的结构进行表征.通过变温电导率的测试,对薄膜的电学输运性质进行了分析.研究结果表明：退火温度为700 ℃时,样品中开始有纳米晶形成,随着退火温度的增加,样品的晶化比增大,在1000 ℃时,薄膜的晶化比达到90%以上.在700 ℃退火时,薄膜中晶化成分较低,载流子的传输特性主要受到与硅悬挂键有关的缺陷态影响,表现为带尾定域态的跳跃电导 关键词： 氢化非晶硅 退火 纳米硅 电输运     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.