Monitoring three typical phenol endocrine disrupting compounds in drinking water of Suzhou urban area – from raw water to tap water

In this work, three typical phenol endocrine-disrupting compounds (EDCs), namely Bisphenol A (BPA), 4-nonylphenol (4-NP) and 4-tert-octyphenol (4-t-OP), were detected in water samples from the whole drinking water supply chain of seven water plants at three hydrographic periods in Suzhou, China. Almost all of the drinking water in urban area of Suzhou city is provided by the seven water plants. Every link of drinking water supply, including raw water, finished water and tap water were monitored. The results indicated that BPA and 4-NP were detected in all samples with the concentration of 0.067–0.118 μg L^?1 and 0.111–0.350 μg L^?1, respectively, while 4-t-OP could be detected in only a few raw water samples with the concentration lower than its limit of quantitation (LOQ). The levels of BPA and 4-NP in raw water were significantly different among three hydrographic periods and the highest concentration can be observed in dry period. The difference in removal efficiency of BPA and 4-NP in seven water plants was also observed among three hydrographic periods, e.g. relative higher in dry period for BPA and in flow period for 4-NP. Potential risk assessment hinted that BPA and 4-NP in raw water showed a low to medium and a medium to high risk respectively to aquatic environment, while in tap water, the health risk from BPA and 4-NP could be ignored on human.     

Potential hazards and health assessment associated with different water uses in the main industrial cities of Egypt

Deterioration of water quality has become an ecological threat in many industrial areas worldwide due to unmanaged anthropogenic activities. Contaminants therein find out their ways to drinking water-pipes via broken or leak old- pipes. The current study aims at evaluating the suitability of tap water, collected from the main-ten-industrial cities of Egypt, for drinking purposes. Shallow and deep ground waters were also sampled from the same locations. This is one of the few research projects that are interested in quantifying the acrylamide in drinking water. The obtained results indicate that concentrations of COD, BOD, Fe, Mn, Ni, Pb, Cd, Zn and Hg were within the permissible levels in tap water while surpassed these levels in both shallow and deep ground waters. Acrylamide levels did not exceed the acceptable levels in all water samples (drinking, surface and deep ground waters). Overall, no potential risks were associated with the oral ingestion of tap water in all studied locations for both adults and children (all hazard quotient (HQ) values, defined as exposure intake dose of contaminants relative to the maximum permissible daily intake dose were below “1″). However, inorganic pollutants that exist in ground waters may cause undesirable dermal impacts when used for irrigating the green areas in these cities (used for picnics and as playgrounds). In this context, most HQ values associated with ground water dermal contact were above “1”. Specifically, Mn, Ni, Pb and Cd hazards exist for children (HQ > 1) while Ni, Pb and Cd toxicity detected for adults. This result; therefore, highlights the indirect negative impacts of industrialization on human health.     

Determination of Background Concentrations of Ag,Pd, Pt and Au in Highly Mineralized Ground Waters at Sub-ng L–1 Concentrations by Online Matrix Separation/Pre-Concentration Coupled to ICP-SFMS

Though not regulated in directives such as the Water Framework Directive of the European Union, the investigation of geogenic background concentrations of certain elements such as precious metals is of increasing interest, in particular for the early detection of a potential environmental pollution due to the increased use in various industrial and technological applications and in medicine. However, the precise and accurate quantification of precious metals in natural waters is challenging due to the complex matrices and the ultra-low concentrations in the (sub-) ng L⁻¹ range. A methodological approach, based on matrix separation and pre-concentration on the strong anion exchange resin TEVA^® Resin in an online mode directly coupled to ICP-SFMS, has been developed for the determination of Ag, Pt, Pd and Au in ground water. Membrane desolvation sample introduction was used to reduce oxide-based spectral interferences, which complicate the quantification of these metals with high accuracy. To overcome errors arising from matrix effects—in particular, the highly varying major ion composition of the investigated ground water samples—an isotope dilution analysis and quantification based on standard additions, respectively, were performed. The method allowed to process four samples per hour in a fully automated mode. With a sample volume of only 8 mL, enrichment factors of 6–9 could be achieved, yielding detection limits <1 ng L⁻¹. Validation of the trueness was performed based on the reference samples. This method has been used for the analysis of the total concentrations of Ag, Pt, Pd and Au in highly mineralized ground waters collected from springs located in important geological fault zones of Austria’s territory. Concentrations ranges of 0.21–64.2 ng L⁻¹ for Ag, 0.65–6.26 ng L⁻¹ for Pd, 0.07–1.55 ng L⁻¹ for Pt and 0.26–1.95 ng L⁻¹ for Au were found.     

A Simple Turn-off Schiff Base Fluorescent Sensor for Copper (II) Ion and Its Application in Water Analysis

An aniline-functionalized naphthalene dialdehyde Schiff base fluorescent probe L with aggregation-induced enhanced emission (AIEE) characteristics was synthesized via a simple one-step condensation reaction and exhibited excellent sensitivity and selectivity towards copper(II) ions in aqueous media with a fluorescence “ turn-off ” phenomenon. The detection limit of the probe is 1.64 × 10⁻⁸ mol·L⁻¹. Furthermore, according to the results of the UV-vis/fluorescence titrations, Job’s plot method and ¹H-NMR titrations, a 1:2 stoichiometry was identified. The binding constant between L and Cu²⁺ was calculated to be K_a = 1.222 × 10³. In addition, the AIEE fluorescent probe L could be applied to detection in real water samples with satisfactory recoveries in the range 99.10–102.90% in lake water and 98.49–102.37% in tap water.     

A simple approach for ultrasensitive detection of bisphenols by multiplexed surface-enhanced Raman scattering

Bisphenol A (BPA) is well known for its use in plastic manufacture and thermal paper production despite its risk of health toxicity as an endocrine disruptor in humans. Since the publication of new legislation regarding the use of BPA, manufacturers have begun to replace BPA with other phenolic molecules such as bisphenol F (BPF) and bisphenol B (BPB), but there are no guarantees regarding the health safety of these compounds at this time. In this context, a very simple, cheap and fast surface-enhanced Raman scattering (SERS) method was developed for the sensitive detection of these molecules in spiked tap water solutions. Silver nanoparticles were used as SERS substrates. An original strategy was employed to circumvent the issue of the affinity of bisphenols for metallic surfaces and the silver nanoparticles surface was functionalized using pyridine in order to improve again the sensitivity of the detection. Semi-quantitative detections were performed in tap water solutions at a concentrations range from 0.25 to 20 μg L⁻¹ for BPA and BPB and from 5 to 100 μg L⁻¹ for BPF. Moreover, a feasibility study for performing a multiplex-SERS detection of these molecules was also performed before successfully implementing the developed SERS method on real samples.     

Content of Carotenoids,Violaxanthin and Neoxanthin in Leaves of Triticum aestivum Exposed to Persistent Environmental Pollutants

Persistent pollutants such as pharmaceuticals, pesticides, musk fragrances, and dyes are frequently detected in different environmental compartments and negatively impact the environment and humans. Understanding the impacts of diffuse environmental pollutants on plants is still limited, especially at realistic environmental concentrations of contaminants. We studied the effects of key representatives of two major classes of environmental pollutants (nine different antibiotics and six different textile dyes) on the leaf carotenoid (violaxanthin and neoxanthin) content in wheat (Triticum aestivum L.) using different pollutant concentrations and application times. The wheat plants were watered with solutions of selected environmental pollutants in two different concentrations of 0.5 mg L⁻¹ and 1.5 mg L⁻¹ for one week (0.5 L) and two weeks (1 L). Both categories of pollutants selected for this study negatively influenced the content of violaxanthin and neoxanthin, whereas the textile dyes represented more severe stress to the wheat plants. The results demonstrate that chronic exposure to common diffusively spread environmental contaminants constitutes significant stress to the plants.     

Determination of Polybrominated Diphenyl Ethers in Water Samples Using Effervescent-Assisted Dispersive Liquid-Liquid Icroextraction with Solidification of the Aqueous Phase

An effective and sensitive method is necessary for the determination of polybrominated diphenyl ethers (PBDEs) pollutants in water. In this study, effervescent-assisted dispersive liquid-liquid microextraction with solidification of the aqueous phase (EA-DLLME-SAP), followed by Gas Chromatography-Tandem Mass Spectrometry (GC-MS-MS) quantitative analysis, was established for the preconcentration and determination of PBDEs in real environmental water samples. 1,1,2,2-Tetrachloroethane was used as the extractant and directly dispersed into the water phase of the aqueous samples with the aid of a large number of carbon dioxide bubbles generated via the acid-base reaction of acetic acid and sodium bicarbonate, which did not require the use of a dispersant during the extraction process. The key factors affecting the extraction recovery were optimized, and an internal standard was used for quantitative analysis, which gave good linearity ranges of 1–100 ng·L⁻¹ (BDEs 28, 47, 99, and 100), 2–200 ng·L⁻¹ (BDEs 153, 154, and 183) and 5–500 ng·L⁻¹ (BDE 209) with limits of quantification in the range of 1.0–5.0 ng·L⁻¹. The accuracy was verified with relative standard deviations < 8.5% observed in tap, lake, river and reservoir water samples with relative recoveries ranging from 67.2 to 102.6%. The presented method contributes to the determination of PBDEs in environmental water samples.     

Determination of priority pollutants in aqueous samples by dispersive liquid–liquid microextraction

A dispersive liquid–liquid microextraction (DLLME) method followed by high-performance liquid chromatography–triple quadrupole mass spectrometry has been developed for the simultaneous determination of linear alkylbenzene sulfonates (LAS C₁₀, C₁₁, C₁₂, and C₁₃), nonylphenol (NP), nonylphenol mono- and diethoxylates (NP₁EO and NP₂EO), and di-(2-ethylhexyl)phthalate (DEHP). The applicability of the method has been tested by the determination of the above mentioned organic pollutants in tap water and wastewater. Several parameters affecting DLLME, such as, the type and volume of the extraction and disperser solvents, sample pH, ionic strength and number of extractions, have been evaluated. Methanol (1.5 mL) was selected among the six disperser solvent tested. Dichlorobenzene (50 μL) was selected among the four extraction solvent tested. Enrichment factor achieved was 80. Linear ranges in samples were 0.01–3.42 μg L⁻¹ for LAS C₁₀–₁₃ and NP₂EO, 0.09–5.17 μg L⁻¹ for NP₁EO, 0.17–9.19 μg L⁻¹ for NP and 0.40–17.9 μg L⁻¹ for DEHP. Coefficients of correlation were higher than 0.997. Limits of quantitation in tap water and wastewater were in the ranges 0.009–0.019 μg L⁻¹ for LAS, 0.009–0.091 μg L⁻¹ for NP, NP₁EO and NP₂EO and 0.201–0.224 μg L⁻¹ for DEHP. Extraction recoveries were in the range from 57 to 80%, except for LAS C₁₀ (30–36%). The method was successfully applied to the determination of these pollutants in tap water and effluent wastewater from Seville (South of Spain). The DLLME method developed is fast, easy to perform, requires low solvent volumes and allows the determination of the priority hazardous substances NP and DEHP (Directive 2008/105/EC).     

Redox Speciation of Vanadium in Estuarine Waters Using Improved Methodology Based on Anion Exchange Chromatography Coupled to HR ICP-MS System

An improved methodology was developed for V redox speciation in estuarine waters using a hyphenated technique consisting of ion chromatograph (IC) with an anion exchange column and a high-resolution inductively coupled plasma mass spectrometer (HR ICP-MS). This approach enables the direct determination of V(V), whereas reduced species (mainly V(IV)) are calculated by subtracting V(V) concentrations from the measured total V concentration. Based on the “on-column” V(V) chelation mechanism by EDTA, with the eluent composed of 40 mmol L⁻¹ ammonium bicarbonate, 40 mmol L⁻¹ ammonium sulphate, 8 mmol L⁻¹ ethylenediaminetetraacetic acid and 3% acetonitrile, the method was successfully used for analyses of V redox speciation in samples taken in the vertical salinity gradient of the highly stratified Krka River estuary. Due to the matrix effects causing different sensitivities, a standard addition method was used for V(V) quantification purposes. The limit of detection (LOD) was also found to be matrix related: 101.68 ng L⁻¹ in the seawater and 30.56 µg L⁻¹ in the freshwater. Performed stability tests showed that V redox speciation is preserved at least 7 days in un-treated samples, possibly due to the stabilization of V-reduced species with natural organic matter (NOM). The dominant V form in the analysed samples was V(V) with the reduced V(IV) accounting for up to 26% of the total dissolved pool. The concentration of V(IV) was found to correlate negatively with the oxygen concentration. Significant removal of dissolved V was detected in oxygen depleted zones possibly related to the particle scavenging.     

An Assessment of Mass Flows,Removal and Environmental Emissions of Bisphenols in a Sequencing Batch Reactor Wastewater Treatment Plant

This study analyzed 16 bisphenols (BPs) in wastewater and sludge samples collected from different stages at a municipal wastewater treatment plant based on sequencing batch reactor technology. It also describes developing an analytical method for determining BPs in the solid phase of activated sludge based on solid-phase extraction and gas chromatography-mass spectrometry. Obtained concentrations are converted into mass flows, and the biodegradation of BPs and adsorption to primary and secondary sludge are determined. Ten of the sixteen BPs were present in the influent with concentrations up to 434 ng L⁻¹ (BPS). Only five BPs with concentrations up to 79 ng L⁻¹ (BPA) were determined in the plant effluent, accounting for 8 % of the total BPs determined in the influent. Eleven per cent of the total BPs were adsorbed on primary and secondary sludge. Overall, BPs biodegradation efficiency was 81%. The highest daily emissions via effluent release (1.48 g day⁻¹) and sludge disposal (4.63 g day⁻¹) were for BPA, while total emissions reached 2 g day⁻¹ via effluent and 6 g day⁻¹ via sludge disposal. The data show that the concentrations of BPs in sludge are not negligible, and their environmental emissions should be monitored and further studied.     

New Strategies for the Simple and Sensitive Voltammetric Direct Quantification of Se(IV) in Environmental Waters Employing Bismuth Film Modified Glassy Carbon Electrode and Amberlite Resin

An analytical procedure regarding the determination of selenium(IV) by anodic stripping voltammetry exploiting the in situ plated bismuth film electrode is described. Since organics are commonly present in untreated natural water samples, the use of Amberlite XAD-7 resin turns out to be quite important to avoid problems such as the adsorption of these compounds on the working electrode. The optimum circumstances for the detection of selenium in water using differential pulse voltammetry techniques were found to be as follows: 0.1 mol L⁻¹ acetic acid, 1.9 × 10⁻⁵ mol L⁻¹ Bi(III), 0.1 g Amberlite XAD-7 resin, and successive potentials of −1.6 V for 5 s and −0.4 V for 60 s, during which the in situ formation of the bismuth film on glassy carbon and the accumulation of selenium took place. The current of the anodic peak varies linearly with the selenium concentration ranging from 3 × 10⁻⁹ mol L⁻¹ to 3 × 10⁻⁶ mol L⁻¹ (r = 0.9995), with a detection limit of 8 × 10⁻¹⁰ mol L⁻¹. The proposed procedure was used for Se(IV) determination in certified reference materials and natural water samples, and acceptable results and recoveries were obtained.     

The Use of a Solid Bismuth Microelectrode for Vanadium Quantification by Adsorptive Stripping Voltammetry in Environmental Water Samples

This paper presents for the first time the use of an environmentally friendly solid bismuth microelectrode for the voltammetric quantification of V(V) in natural water samples. These studies were designed to replace the film bismuth electrode that had been introduced to eliminate the conventional sensors based on highly toxic mercury. In the proposed procedure, V(V) is preconcentrated at the solid bismuth microelectrode surface via the formation of electroactive complexes with cupferron from a solution of 0.1-mol L⁻¹ acetate buffer, pH = 4.6 at a potential of −0.4 V. The linearity of the calibration graph is in the V(V) concentration range from 8 × 10⁻¹⁰ to 1 × 10⁻⁷ mol L⁻¹ with a preconcentration time of 1 min. The limit of detection (calculated as 3 σ) is 2.5 × 10⁻¹⁰ mol L⁻¹ for a preconcentration time of 1 min. It was also demonstrated that significant improvement in analytical parameters was achieved as a result of the activation of the solid electrode surface at a potential of −2.5 V for 2 s. The developed procedure is highly selective for the presence of foreign ions and organic compounds in tested samples. The accuracy of the recommended procedure was checked using SPS-WW1 waste water-certified reference materials of a complex composition, in which the concentration of V(V) determined by the proposed method was 95.1 ± 1.6 ng mL⁻¹. Moreover, in keeping with the outlined procedure, river, tap and rain water samples were analyzed without any pretreatment, and recovery values from 96% to 106% were obtained.     

A switchable sensor and scavenger: detection and removal of fluorinated chemical species by a luminescent metal–organic framework

Fluorosis has been regarded as a worldwide disease that seriously diminishes the quality of life through skeletal embrittlement and hepatic damage. Effective detection and removal of fluorinated chemical species such as fluoride ions (F⁻) and perfluorooctanoic acid (PFOA) from drinking water are of great importance for the sake of human health. Aiming to develop water-stable, highly selective and sensitive fluorine sensors, we have designed a new luminescent MOF In(tcpp) using a chromophore ligand 2,3,5,6-tetrakis(4-carboxyphenyl)pyrazine (H₄tcpp). In(tcpp) exhibits high sensitivity and selectivity for turn-on detection of F⁻ and turn-off detection of PFOA with a detection limit of 1.3 μg L⁻¹ and 19 μg L⁻¹, respectively. In(tcpp) also shows high recyclability and can be reused multiple times for F⁻ detection. The mechanisms of interaction between In(tcpp) and the analytes are investigated by several experiments and DFT calculations. These studies reveal insightful information concerning the nature of F⁻ and PFOA binding within the MOF structure. In addition, In(tcpp) also acts as an efficient adsorbent for the removal of F⁻ (36.7 mg g⁻¹) and PFOA (980.0 mg g⁻¹). It is the first material that is not only capable of switchable sensing of F⁻ and PFOA but also competent for removing the pollutants via different functional groups.

A robust In-MOF, In(tcpp), demonstrates sensitive detection of the fluorinated chemical species F⁻ and PFOA via distinctly different luminescence signal change, and effective adsorption and removal of both species from aqueous solution.     

Biosensor immunoassays for the detection of bisphenol A

Bisphenol A (BPA) is a xenoestrogen found in the environment, in consequence, for the biosensor detection of BPA we raised antibodies (polyclonal (PAbs) and monoclonal (MAbs)) against a structural analogue of BPA, 4,4 bis-(4-hydroxyphenyl) valeric acid (BVA). The kinetics of the MAb-BPA interaction were evaluated and the MAb providing the highest affinity was directly immobilized onto the sensor chip surface to evaluate a direct assay. Afterwards, the performance of the MAbs and the PAbs was compared in an inhibition assay using a BVA-coated chip.The highest sensitivity (limit of detection (LOD) of 0.4 μg L⁻¹) was obtained with MAb 12 in the direct assay. However, the inhibition assay was the most robust and the PAbs showed the highest sensitivity (LOD of 0.5-1 μg L⁻¹). The antibodies were specific for BVA and BPA as only minor cross-reactivities were found toward structurally related compounds or other endocrine disruptors. In the inhibition assay (with a run time of 6 min), water samples spiked with BPA at different levels (0.5-50 μg L⁻¹) resulted in recoveries varying between 68% and 121%. The sensitivity of the inhibition assay could be improved 40 times (LOD of 0.03 μg L⁻¹ with the Mab 12-based assay) using solid phase extraction (SPE).     

Improved Metal Cation Optosensing Membranes through the Incorporation of Sulphated Polysaccharides

Optosensing chitosan-based membranes have been applied for the detection of heavy metals, especially in drinking water. The novelty of this study is based on the use of sulphated polysaccharides, in such optosensing membranes, aiming at an improved analytical performance. The sulphated polysaccharides, such as ulvan, fucoidan and chondroitin sulfate, were extracted from by-products and wastes of marine-related activities. The membranes were developed for the analysis of aluminum. The variation in the visible absorbance of the sensor membranes after the contact between the chromophore and the aluminum cation was studied. The membranes containing sulphated polysaccharides showed improved signals when compared to the chitosan-only membrane. As for the detection limits for the membranes containing ulvan, fucoidan and chondroitin sulfate, 0.17 mg L⁻¹, 0.21 mg L⁻¹ and 0.36 mg L⁻¹ were obtained, respectively. The values were much lower than that obtained for the chitosan-only membrane, 0.52 mg L⁻¹, which shows the improvement obtained from the sulphated polysaccharides. The results were obtained with the presence of CTAB in analysis solution, which forms a ternary complex with the aluminum cation and the chromophore. This resulted in an hyperchromic and batochromic shift in the absorption band. When in the presence of this surfactant, the membranes showed lower detection limits and higher selectivity.     

Determination of eleven priority EPA phenolics at ng L−1 levels by on-line solid-phase extraction and liquid chromatography with UV and electrochemical detection

Summary The eleven priority, EPA phenolic pollutants were determined by liquid chromatography followed by two detectors in series; UV and electrochemical. Three different adsorbents, Envi-Carb (a carbon black) and two functionalized polymeric resins, Bond Elut PPL and another synthesized in our laboratory with an ocarboxybenzoyl moiety, were compared for solid-phase extraction (SPE) to detect lower concentrations of the eleven phenolics in natural waters. Higher recoveries were obtained using the functionalized polymeric adsorbents compared with Envi-Carb. When real samples were analysed, the synthetic adsorbent gave lower interference than Bond Elut PPL and phenol was determined at low levels with no humic and fulvic acid inter-ference when Na₂SO₃ was added. The linearity range for most compounds in tap water was 0.05–20 μg L⁻¹ and the limits of detection were <35 ng L⁻¹. Repeatability and reproducibility between days for real samples spiked at 0.1 μg L⁻¹, expressed as relative standard deviation, were <8% and 10%, respectively.     

Polar herbicides,pharmaceutical products,perfluorooctanesulfonate (PFOS), perfluorooctanoate (PFOA), and nonylphenol and its carboxylates and ethoxylates in surface and tap waters around Lake Maggiore in Northern Italy

A survey of contamination of surface and drinking waters around Lake Maggiore in Northern Italy with polar anthropogenic environmental pollutants has been conducted. The target analytes were polar herbicides, pharmaceuticals (including antibiotics), steroid estrogens, perfluorooctanesulfonate (PFOS), perfluoroalkyl carboxylates (including perfluorooctanoate PFOA), nonylphenol and its carboxylates and ethoxylates (NPEO surfactants), and triclosan, a bactericide used in personal-care products. Analysis of water samples was performed by solid-phase extraction (SPE) then liquid chromatography–triple-quadrupole (tandem) mass spectrometry (LC–MS–MS). By extraction of 1-L water samples and concentration of the extract to 100 μL, method detection limits (MDLs) as low as 0.05–0.1 ng L⁻¹ were achieved for most compounds. Lake-water samples from seven different locations in the Southern part of Lake Maggiore and eleven samples from different tributary rivers and creeks were investigated. Rain water was also analyzed to investigate atmospheric input of the contaminants. Compounds regularly detected at very low concentrations in the lake water included: caffeine (max. concentration 124 ng L⁻¹), the herbicides terbutylazine (7 ng L⁻¹), atrazine (5 ng L⁻¹), simazine (16 ng L⁻¹), diuron (11 ng L⁻¹), and atrazine-desethyl (11 ng L⁻¹), the pharmaceuticals carbamazepine (9 ng L⁻¹), sulfamethoxazole (10 ng L⁻¹), gemfibrozil (1.7 ng L⁻¹), and benzafibrate (1.2 ng L⁻¹), the surfactant metabolite nonylphenol (15 ng L⁻¹), its carboxylates (NPE₁C 120 ng L⁻¹, NPE₂C 7 ng L⁻¹, NPE₃C 15 ng L⁻¹) and ethoxylates (NPE _n Os, n = 3-17; 300 ng L⁻¹), perfluorinated surfactants (PFOS 9 ng L⁻¹, PFOA 3 ng L⁻¹), and estrone (0.4 ng L⁻¹). Levels of these compounds in drinking water produced from Lake Maggiore were almost identical with those found in the lake itself, revealing the poor performance of sand filtration and chlorination applied by the local waterworks.     

Development and characterization of a new polyampholyte-surfactant complex applied to the solid phase extraction of bisphenol-A

This paper presents a material that has both hydrophilic and hydrophobic domains, obtained by combination of a polyampholyte with a surfactant. This material was fully characterized by different spectroscopic techniques and microscopy.Bisphenol-A (BPA) was chosen as a model molecule to study the interaction with compounds of intermediate polarity. We explored the kinetics and equilibrium of BPA on the surface of the polyampholyte-surfactant complex and found a significantly high loading capacity (2.02 mmol g⁻¹) and complete binding from solutions at concentration levels below 100 μmol L⁻¹.The complex was encapsulated in agarose gel to be used as solid phase for extraction of BPA from food simulants in contact with polycarbonate bottles under different treatments. Bisphenol was preconcentrated, extracted and analysed by liquid chromatography with an amperometric detector. The instrumental detection limit of the technique was 10 μg L⁻¹, which was lowered to 0.14 μg L⁻¹ by the preconcentration step. The BPA released from baby bottles was 2.1 ng cm⁻² (σ_n − 1: 0.1) in the first use with distilled water.     

Effect of Must Hyperoxygenation on Sensory Expression and Chemical Composition of the Resulting Wines

This paper evaluates the effect of must hyperoxygenation on final wine. Lower concentrations of caftaric acid (0.29 mg·L⁻¹), coutaric acid (1.37 mg·L⁻¹) and Catechin (0.86 mg·L⁻¹) were observed in hyperoxygenated must in contrast to control must (caftaric acid 32.78 mg·L⁻¹, coutaric acid 5.01 mg·L⁻¹ and Catechin 4.45 mg·L⁻¹). In the final wine, hydroxybenzoic acids were found in higher concentrations in the control variant (gallic acid 2.58 mg·L⁻¹, protocatechuic acid 1.02 mg·L⁻¹, vanillic acid 2.05 mg·L⁻¹, syringic acid 2.10 mg·L⁻¹) than in the hyperoxygenated variant (2.01 mg·L⁻¹, 0.86 mg·L⁻¹, 0.98 mg·L⁻¹ and 1.50 mg·L⁻¹ respectively). Higher concentrations of total flavanols (2 mg·L⁻¹ in hyperoxygenated must and 21 mg·L⁻¹ in control must; 7.5 mg·L⁻¹ in hyperoxygenated wine and 19.8 mg·L⁻¹ in control wine) and polyphenols (97 mg·L⁻¹ in hyperoxygenated must and 249 mg·L⁻¹ in control must; 171 mg·L⁻¹ in hyperoxygenated wine and 240 mg·L⁻¹ in control wine) were found in both the must and the control wine. A total of 24 volatiles were determined using gas chromatography mass spectrometry. Statistical differences were achieved for isobutyl alcohol (26.33 mg·L⁻¹ in control wine and 32.84 mg·L⁻¹ in hyperoxygenated wine), or 1-propanol (7.28 mg·L⁻¹ in control wine and 8.51 mg·L⁻¹ in hyperoxygenated wine), while esters such as isoamyl acetate (1534.41 µg·L⁻¹ in control wine and 698.67 µg·L⁻¹ in hyperoxygenated wine), 1-hexyl acetate (136.32 µg·L⁻¹ in control wine and 71.67 µg·L⁻¹ in hyperoxygenated wine) and isobutyl acetate (73.88 µg·L⁻¹ in control wine and 37.27 µg·L⁻¹ in hyperoxygenated wine) had a statistically lower concentration.     

Free Radical Isomerizations in Acetylene Bromoboration Reaction

The experimentally motivated question of the acetylene bromoboration mechanism was addressed in order to suggest possible radical isomerization pathways for the syn-adduct. Addition–elimination mechanisms starting with a bromine radical attack at the “bromine end” or the “boron end” of the C=C bond were considered. Dispersion-corrected DFT and MP2 methods with the SMD solvation model were employed using three all-electron bases as well as the ECP28MWB ansatz. The rate-determining, elimination step had a higher activation energy (12 kcal mol⁻¹) in case of the “bromine end” attack due to intermediate stabilization at both the MP2 and DFT levels. In case of the “boron end” attack, two modes of C–C bond rotation were followed and striking differences in MP2 vs. DFT potential energy surfaces were observed. Employing MP2, addition was followed by either a 180° rotation through an eclipsed conformation of vicinal bromine atoms or by an opposite rotation avoiding that conformation, with 5 kcal mol⁻¹ of elimination activation energy. Within B3LYP, the addition and rotation proceeded simultaneously, with a 9 (7) kcal mol⁻¹ barrier for rotation involving (avoiding) eclipsed conformation of vicinal bromines. For weakly bound complexes, ZPE corrections with MP2 revealed significant artifacts when diffuse bases were included, which must be considered in the Gibbs free energy profile interpretation.